How to glue a Chinese air mattress. The internal partition in the air bed burst

Each owner of an inflatable product sooner or later faces a problem: how to seal the mattress. An air mattress is a very practical thing. Unfortunately, one of the significant drawbacks of inflatable products is the likelihood of a puncture. With this damage, further operation is simply impossible, and sometimes dangerous - when used on water. Even a very small puncture will lead to the fact that you (or your guests) will wake up in the middle of the night on a lowered “bed”. So, let's discuss how and how to glue the mattress so that it lasts for more than one year.

Can you fix a mattress yourself?

There are many reasons for punctures - a sharp pebble, a fragment, a thorn of a bush or tree, the claws and teeth of a pet. It is definitely not worth it to rush to throw away the product. Repair of an air mattress is a common thing. Most often, patches and glue are used for this.


The repair process is often even easier than finding the puncture itself. When it comes to a tall double model, finding a small puncture is not an easy task.

Note! According to statistics, side seams are most susceptible to damage. The second place in the ranking is occupied by the so-called bottom of the product. But before you start looking for a puncture, you should determine whether a damaged valve is the cause of the pressure loss.

Puncture or hole detection

So, more to the point - how to fix a mattress? As already noted, finding a puncture (especially visually) is not always as easy as it might seem at first glance. For effective detection, use one of the options below.


Water

With the help of water, it is quite easy to detect a puncture. But there is a caveat - you will need a lot of water. If the mattress is large, it will be quite problematic to apply this method in an apartment environment.


It is much easier to detect a problem near a pond. Place the mattress on the water. Ask a few friends to climb on it (so that it is as submerged as possible). Air bubbles will indicate the injury site. Taking the opportunity (the presence of a large amount of water), turn the mattress over and repeat the procedure (suddenly there are damages on reverse side). In apartment conditions rubber product you will have to water section by section with water until a puncture is detected.

Lather


Next effective method. Prepare a liquid soap solution, inflate the mattress and gradually lather the surface with a sponge. Inflating air bubbles will show where the puncture is. This method is also good because in the process of detecting a puncture, you will wash the product at the same time.


In principle, damage can be detected by hearing. It is best to search for a puncture in a quiet, calm place. Pump up the product and listen for the characteristic hissing sound. The sound may be amplified if the mattress is poured with water.

Liquid filling


This method works, but is not recommended for use. Firstly, the product filled with water becomes very heavy, it is rather difficult and inconvenient to turn it over. Secondly, at the end of the detection procedure, it will not be easy to dry the mattress from the inside. If all this does not bother you, pour water with the addition of soapy detergent inside. 3 liters of prepared liquid will be enough.

starch or powder

Any fine powder will do. Sprinkle it on the mattress area by area. Where the powder begins to rise in a cloud is the puncture site.


Note! In some cases, there may be several punctures. Therefore, after finding the first puncture, continue to check the product to make sure there are no other damages.

Getting ready for renovation

After finding all the existing damage, mark them with a marker or outline with a dry remnant. Before the beginning repair work dry the surface completely naturally(rubber product is not recommended to dry near and even more so on heaters). Degrease desired area(alcohol, nail polish remover, gasoline, acetone).


Note! If a puncture was found on the flock side, the area around the damage must be cleaned. For this, it is best to use fine-grained sandpaper. Stripping the pile will allow the patch to better adhere to the surface of the mattress.

Action algorithm

In order not to miss anything, we will describe the algorithm of preparatory actions again.

  1. Find the puncture(s) in one of the ways and mark them.
  2. Release all the air from the mattress.
  3. Dry the item naturally.
  4. Clean the area around the damage (if necessary).
  5. Thoroughly clean the area. Check that there are no small particles, pile left around the damage site.
  6. Prepare the area for gluing the patch - degrease.

Mattress Repair Adhesive


The question is what kind of glue to glue inflatable mattress the choice is better to make in favor of the repair kit from the manufacturer. However, to seal a damaged mattress, you can use any adhesive designed to work with PVC and rubber products. As an option:

  • "Moment" is universal - provides reliable bonding, dries up during the day.
  • "Desmokol" or similar polyurethane (quite often used for shoe repair).
  • Adhesives for repairing PVC boats.
  • Glue INTEX.


Special attention should be paid to the last option, especially if you are the owner of the product of this company. Glue from a global manufacturer, ideal for repairing INTEX inflatable products. Usually, in addition to glue, the kit includes a vinyl film, a flock patch and instructions for performing work. The set is simple and easy to use. Among other things, patches have a variety of colors.

Note! It is not recommended to use superglue or supermoment for repairs. These adhesives harden after drying. Over time, they begin to crumble, which can damage the mattress.

Patch preparation

Do not use large patches. Optimal size- one and a half by one and a half centimeters. Before using the patch, it must be degreased. Rubber parts can only be glued together after the degreasing agent has completely dried.


How to patch an air mattress when there is no professional repair kit at hand? In such a situation, you need to cut a patch from any suitable material. You can use flock rubber (from a child's toy) or a piece of vinyl (from an old air mattress). If there is a leaky bicycle tube in the shed or garage, cut off a piece of it right size. It will act as a patch. For reliability, cut the patches with a small margin around the edges (no more than 3 cm). Cut off the excess in the process.

How to apply a patch

The amount of glue used depends on its type. So for example, "Moment" universal is applied quite thickly. Desmokol, on the contrary, needs to be distributed thin layer. After applying the glue, it is necessary to dry it a little, but not more than 10 minutes (read in the instructions). You can shorten the time with a hair dryer.


Press the prepared patch firmly and leave to dry under pressure. The "hold" time will vary depending on the type of adhesive. Usually - from 30 minutes to a day.

What if the problem is in the seam

If the seam is damaged, there may be several options for solving the problem. If the puncture is very small, fill the puncture site with glue and leave to dry completely.


The second option is more troublesome, but at the same time more reliable. Through the valve, pull out the wrong side damaged area. Further - everything is as usual. Degrease, dry, apply glue, wait 10 minutes, press the patch to the puncture site, leave the product for 12 hours.

What if the damage was formed at the site of the previously glued patch? How to seal a hole in a mattress in this case? Do not delete the old one. The hole may enlarge during pull-off. Instead, glue trouble spot patchwork bigger size, which will block the old one with a margin.


To avoid the possibility of "pulling" the edges of the patch, they should be sanded with sandpaper. Then apply a thin layer of glue along the edge of the patch.

findings

A mattress puncture is not a reason to dispose of it. The algorithm of actions is as follows: find damage, decide how to glue the air mattress, carefully prepare the site and “patch”. Best of all, professional repair kits from the manufacturer cope with the task. If it is not possible to purchase such a kit, use it as an adhesive for an air mattress universal options(for rubber and PVC), and as an impromptu patch fit: an old children's toy, a ball, an unusable air mattress or a bicycle camera.



Video

Air mattresses are a versatile product with a wide range of applications. They are easy to use, compact, and relatively inexpensive. However, perfect things do not happen and any air mattresses have one popular problem - rubber is susceptible to damage from any sharp objects.

To fix a defect, you need to find the defect. Most often, finding a hole is not as easy as it seems. In addition, even if you find noticeable damage, this does not mean that there are no small scratches nearby that allow air to pass through. To find damage, you need to inflate the mattress and place it in water. Small air bubbles will appear at the puncture site.

If it is not possible to place the mattress in water, lubricate it with soapy foam or shaving foam. The puncture site will begin to let air through and the applied foam will begin to bubble. This video shows how bubbles come out at the puncture site when applying foam

Pay attention to the seams - most often they are torn due to the strong blowing of the mattress. Mark the location of the leaky mattress with a marker or pen.

How to seal an air mattress

What is needed for repair

Most often, a repair kit comes with the purchase in the kit. But if it was lost, take glue, scissors, a dry cloth, alcohol, a piece of rubber (tire patches, an old bicycle inner tube are good). PVC glue - will be the best choice, it does not leave a cracking crust after drying. Glue for shoes is also suitable - it bends well and glues the surface perfectly.

Surface preparation and mattress patches

Before starting the process, dry the mattress well, blow it off, remove small debris and dust from the surface. Wipe the restoration site itself with a cloth soaked in alcohol - this will help remove excess moisture from the surface and degrease it.

Often, the place of damage is applied a large number of glue. Because of this, the mattress dries out for a long time and puffs up in the places of the patch. Be extremely careful, apply glue in a thin stream. Prepare the surface properly.

Velor side

To repair the velor side, you will need to clean the repair area.

  • First you need to clean the layer of villi. Pour solvent or nail polish remover over the puncture site and within a 0.5 cm radius around it. After application, wait two minutes and remove the velor layer with a dull knife or spoon.
  • We cut out a circle from the prepared rubber with a diameter of 1 cm more than the damage itself.
  • We apply glue to the patch and a little to the damaged surface.
  • We evenly apply a piece of rubber, press it a little and hold for 2-3 minutes until it dries.

From the smooth side

On the smooth side, repairs are a little easier.

  • It is necessary to dry the puncture site well, degrease it with alcohol, wipe it with a dry cloth.
  • Apply adhesive to patch and surface. The radius of the rubber should also be 1 cm larger than the damage site.
  • We apply a patch, press and wait 2-3 minutes.

Along the seam

If you glue the mattress along the seam or fold from the outside, the repair will not be reliable. Therefore, you need to open the valve, completely deflate the mattress, pull out the puncture site through the valve. This way you can work with the wrong side.

  • The surface should be degreased with alcohol, wiped well.
  • Seal with a patch with a radius greater than the area of ​​the cut.
  • Apply glue and put the product under the press.
  • Check if the patch is moving out of place. If unsuccessful, repeat the procedure.

The effectiveness of this method lies in the fact that in this case the patch closes the hole in the mattress and is also held with the help of air pressure from the inside.

To avoid new damage:

  • Do not blow air over the mattress - because of this, it often tears at the seams or even bursts.
  • Before you put the mattress on the surface - inspect it for sharp objects.
  • Try to distribute the weight on the surface of the mattress when using.
  • Do not allow any sharp objects to the mattress, avoid being near animals.

The mattress will serve you much longer if you follow certain rules.

  1. Fold the mattress evenly at the seams, store in a cover for safety.
  2. After swimming and any contact with water, dry the product, and then pack it.
  3. Remove dust and dirt only with mild soap solutions, without contact with chemicals cleaning.
  4. The mattress should be inflated according to the purpose and weight of the person who will use it. The heavier the weight, the weaker it should be inflated.

Air mattresses often get damaged - a long-known fact. But repairing them is no big deal. To carry out quality repair mattress needs to be selected the right materials and approach the matter wisely. Not all improvised means are suitable for correcting defects, but to glue different materials needed differently. In order for the mattress to serve for a long time and correctly, it is enough just to follow these recommendations. And remember - different mattresses have various uses. Handle the thing for its intended purpose and carefully, and then you definitely won’t have to deal with repairs.

An air mattress is not only good decision for water activities, but also an alternative to a bed. At home, it can be used to accommodate guests. Such products are compact, when folded they practically do not take up free space.

They are durable, especially when handled with care. But, even in the event of a puncture, can be glued air mattress by yourself. Required for repair inexpensive materials, available in hardware and hardware stores, a minimum set of tools and improvised means.

Should You Repair Your Mattress?

The mattress can be damaged both during rest - by branches, stones or even sand, and at home, for example, thanks to pets. But, you don't need to get rid of it. Do-it-yourself restoration is needed patches and glue. Following the instructions, you can glue an air mattress at home no worse than professional craftsmen.

It is easy to seal a rubber product, it is much more difficult to find a hole in an air mattress. It is usually very small visual inspection And it's hard to find the sound. First of all, you need to check the valve. It could wear out and start leaking air.

In 90% of cases, holes in mattresses are formed at the seams. Damage is the next most common. bottom surface. It is often damaged by debris present in nature or in a pond, but it can also be pierced at home.

First of all, you should decide with the site of injury. First you need to visually inspect the entire product. If it was not possible to identify a puncture, several more effective methods are used.

Search for a damaged place

Often it is not possible to visually find a hole in the rubber due to its elasticity. But, at severe damage, such places are noticeable. If it is visible visually, attach to it to check back side palms. If there is a hole, you will feel a cool air flow.

It is better dip your hand in water. This makes it easier to detect air flow, as air bubbles should appear when you apply the brush. You should not rush, examine the surface in detail, perhaps several holes have formed.

Immersion in water

If the defect is found directly on the pond, the mattress should be inflated and immersed in water. To create extra pressure you can sit on the product. Bubbles should come out of the hole. The place of their exit is the damage.

With soapy water

Bubbles will be more visible if you use soapy water. You can simply treat the entire mattress with soap using a sponge or cloth. Fits both regular and liquid soap. It is more convenient to work with the latter, since it already has a liquid consistency.

Add some soap to the water and go over the entire piece with a washcloth. Special attention give seams. Bubbles will start to stand out even from small holes.

By sound

The hole can be found at characteristic sound. But, it is advisable to do this in a quiet place, without distracting noises. Inflate the product and lean against it in different places. A characteristic hiss will be present at the puncture site.

Liquid filling

Due to the inconvenience, this method is rarely used, but in difficult cases it can be more efficient. The mattress must be filled with water. If there is a gap, liquid will flow through it. You can fill the product with a watering can.

The disadvantage of this method lies in the complexity of the subsequent drying of the internal cavity. The design is almost completely sealed, so even with open valve, the product will dry for a long time. Therefore, it is recommended to resort to this option only in summer in warm weather in order to speed up drying.

May remain on the mattress white stains. If this is not critical, follow these steps:

  • release the air;
  • prepare water with a small amount soap (you can use plain water, but with soap the efficiency is higher);
  • pour approximately 3 liters of liquid into the mattress. When working with overall models more volume may be required;
  • inflate the mattress tightly;
  • Turn the product over several times so that the solution is distributed along the inner walls. The gap will be noticeable by hissing and water flowing out;
  • use a marker, chalk, or soap to mark the puncture.

Surface preparation for gluing

Rubber at the site of damage must be cleaned of contamination. The surface must be completely dry. Do not dry the mattress hair dryer or heaters, it may damage the material.

If a hole is formed on the fleecy side, the area must be lightly cleaned with a fine-grained sandpaper. This is necessary to ensure the tightness of the patch and improve the adhesion of the adhesive.

Degrease the cleaned area. You can use alcohol, acetone (nail polish remover will do) or similar non-aggressive solvents. You can use a small amount of gasoline.

Tools and materials

There are several ways to seal an air mattress. The best option- use a special repair kit. The Intex company produces such restoration kits its products. Set includes:

  • transparent vinyl film;
  • flock patch;
  • glue.

The set comes with instructions. Repair kits are sold in stores specializing in the sale of mattresses and auto parts. It is advisable to buy 1-2 sets when purchasing the product. The set is compact, if necessary, you can take it with you on vacation.

In the absence of the possibility of buying a ready-made set, you should resort to improvised materials:

  • a patch can be made from any piece of rubber - old wheel tubes, children's toys, circles, etc .;
  • for gluing, you can use any glue for rubber products. But, do not use superglue, it will damage the material.

To perform the work, you need scissors, sandpaper with fine grain, a brush for applying the adhesive composition and a marker for making marks.

Adhesive selection

There are a lot of adhesives on the market that are designed to work with rubber. But, can not use products with the effect of instant gluing. They usually contain a substance that corrodes rubber.

The moment is universal

One of the most popular adhesives. Suitable for both rubber and other materials, including plastic, ceramics, wood and others. The joint reaches maximum strength after 24 hours.

Polyurethane Shoe Adhesive

Adhesive solution based on polyurethane. Also found on sale under the name "Desmokol". Effective remedy recovery leather goods, but also glues rubber parts well.

PVC adhesive

An effective solution for PVC products. Also suitable for air mattresses. The advantage is that there is no need to use a separate patch. It is formed by itself adhesive composition during polymerization, due to which it received the name "Liquid Patch".

Not affected by moisture. Available in various colors, which allows you to repair any product without compromising aesthetic qualities.

Super Moment

Composition based on natural rubber. But, for the restoration of rubber mattresses, it is better not to use. After hardening, it acquires a very hard structure, in further operation it can crumble, including damaging the mattress material.

rubber adhesive

Applied on both bonded surfaces. After application, you need to wait 2-5 minutes, attach the parts and squeeze tightly. It is advisable to leave the connection under pressure for a while. Full hardening occurs after a day.

Making a patch

The size of the patch should completely cover the hole, capturing a little of the surrounding whole material. But, it is not worth making it excessively large, this will create an additional load on the rubber. Before gluing the patch and the damaged area, be sure to degrease.

If there are several adjacent gaps, they can be sealed with one large patch. But, it should completely cover the damaged area and have a small margin.

Surface sealing

The thickness of the adhesive layer depends on its type, so you need to follow the instructions from the manufacturer. So, "Moment" is applied in a thicker layer, and "Desmokol" is as thin as possible. After application, wait a while for the adhesive to dry slightly.

Apply the patch to the injury and press firmly for 2 minutes. Try to press the entire part at once, eliminating its displacement. The mattress can be used after the glue has hardened, the specific time is always indicated in the instructions.

Seam sealing

Seams can usually be sealed with glue. It is important to wait for it to completely harden. The layer is thick, so you have to wait a while, preferably at least a day. There is also a more complicated but effective solution:

  • the damaged part of the product must be turned out through the valve hole;
  • degrease the damaged seam;
  • wait for the product to dry;
  • cut a patch from a rubberized fabric and glue it;
  • press the part firmly against the defective seam.

Using this method, do not rush to operate the product. Leave it on for at least 12 hours. After the glue has cured, turn the product inside out and inflate to check.

If the restoration fails, try repairing the gap again. Do not dismantle the patch, but stick an additional larger one on top of it. Especially carefully lubricate the edges of the patch with glue. Peeling of the part usually starts from the edges.

To prevent the patch from peeling off after repair, clean it with sandpaper and completely cover it with glue.

How to avoid new damage?

Not recommended transport the mattress in an inflated state. If there is no desire to blow it off every time, at least you need to carefully carry it in your hands, trying not to catch third-party objects. Allocate a separate place for him at home, better inaccessible to children and animals. Keep the product dry only. If the mattress is used as a guest bed at home, keep it in its original packaging and deflate it when not needed.

In each modern family there is an air mattress. It serves as a bed for suddenly arriving guests, it can be taken on vacation: it is useful for swimming, it can be used as a bed, it is convenient to sunbathe on it.

But sometimes on vacation there is a problem of air blowing, let's see how to solve it,how to stick an air mattress.

In contact with

Product features

An air mattress is a cavity made of a special material of various sizes, which, as a result of filling with air, transforms into a sleeping place. In size, they are single and one-and-a-half, but there are also wider air beds. They also differ in height - there are large models up to 50 cm, and small ones up to 23 cm.

They have firmly entered the everyday life of students, nomadic brigades and those who do not have permanent housing, are forced to move often. It is also good to have an air bed if the area of ​​​​the apartment is small, so that you can put it in the closet in the morning.

The presented products are made of polyvinyl chloride - this is a rather soft elastic material, but, unfortunately, it is prone to be easily damaged.

Therefore, every home should know how to implementrepair of air mattresses.

For those who cannot stand the chemical smell, environmentally friendly products are available.mattresses without glue and smell.

They are often bought for children or the elderly who react painfully to various chemical components.

Attention!A high mattress can be used as a permanent bed, covering it with a bedspread. In this form, it looks like a regular bed.

Such products are indispensable on vacation, you can sleep, sunbathe and swim on them.

Valve Troubleshooting

If the product is not damaged in the form of holes and cuts, and it gradually releases air, then the reason lies in the malfunction of the valve. If aair mattress repair shopis far away, you can fix the problem yourself at home, following the step-by-step instructions:

  1. Fill the product with air and lubricate the valve with soapy foam. If it lets air through, then foam will appear around it.
  2. Then you need to remove the adjacent valve, and then the rubber gasket.
  3. The valve end must be sanded with fine sandpaper and lubricated with silicone grease.
  4. Then put the valve back in its original place and inflate the product again to check.

Serious damage to the valve can only be repaired in the workshop. With such a simple taskhow to fix an air mattress, any owner can handle it.

How to find a puncture

Preliminary repair requires study of the issue,how to find a hole in an inflatable question, because it is this unfortunate nuisance that causes spoiled rest and sleep. There are several methods for searching:


  1. Tactile. This puncture detection method does not have any materials at hand. The mattress must be pumped up well and held with your hands above its surface at a height of 2-3 cm. At the location of the hole, your hands will feel a trickle of air. To increase sensitivity, hands should be moistened with plain water.Also, the puncture site can be detected by ear - a hiss and whistle will be heard from the damage.
  2. Soapy. Dilute a strong soapy solution, and then apply it to the surface with a sponge. Bubbles will form at the location of the puncture, mark it with a marker.
  3. Submersible. Mattresses small size you can simply immerse it in a container of water and see where the air bubbles come from.
  4. Water. In this method, water is poured into the mattress - a small amount is used. The mattress needs to be shaken and then inspected. If a wet spot is found on its surface, then a puncture is located in this place.

Advice!It is necessary to start looking for damage from the valve, and then from the side seams: they are the ones that suffer the most from overload. Next, you need to check lower part, which is in contact with the ground or floor, because it is more prone to punctures.

Preparation for repair


Before starting the repair, it is necessary to prepare its surface for work. First, the mattress must be deflated and dried thoroughly.

You need to know how to properly deflate mattresses. AT simple models just open the valve and wait a certain time. It cannot be pressed or crushed.

In other models, this is done differently.

For example, it is necessary to know exactlyhow to deflate a BESTWAY mattress, because it has a special damper that prevents the mattress from deflated if the valve cover is accidentally opened.

In this case, you need to open the lid, and move the plate to the side, then the air will come out.

Now the puncture sites must be degreased with alcohol, acetone or gasoline. The flock coating will have to be removed, that is, carefully cut off. Rubber or plastic does not need to be further processed and cleaned.

Patch preparation

When making a patch, you should knowhow to stick an air mattress. If there is no material suitable for repair at hand, then any will do piece of thin rubber. You can take a piece from the car or bicycle camera, children's toy or any rubberized object. You can also make a patch from a cotton fabric pre-impregnated with rubber glue.

What glue is suitable for repair


For product repair, it is importanthow to glue an air mattress. There are many adhesives, each designed to work with a certain type of material.

Experts advise choosing universal varieties, rubber and PVC composition.After drying, the adhesive should form a strong, elastic and water-resistant connecting layer.

Glue should be used in minimal quantities so that the layer is thin - excess will not help glue the rubber parts. For repairs, it is recommended to use the following types of glue:

  1. Moment. This is universal glue, it holds together almost any materials: rubber, plastic, PVC, fabrics and much more.
  2. Polyurethane shoe. This is a reliable adhesive, it forms a strong layer between the bonding surfaces. Only when applying glue, the surfaces should be joined and dried with a hair dryer.
  3. Adhesive for PVC. Air mattresses are often made from polyvinyl chloride, so the type of glue presented is best suited for them. It is necessary to glue, applying 2 layers on both surfaces, after which the composition is aged for 20 minutes.
  4. Super moment. Fast adhesives are also suitable for repairing this product, but contain substances that damage the surface.His main disadvantage- this is premature hardening and brittleness during the operation of the product.When the mattress dries out, crackling of the adhesive mass can be found on the folds, which will again lead to the need for repairs.
  5. Real rubber glue. Does not leave stains when glued. It is necessary to apply two layers of glue to the surface, let it dry, then connect the surfaces and put a load on them for a day.

Advice!If there is no rich choice at hand, you can patch with any glue. It is important to follow the instructions for gluing surfaces.

What is needed for repair

Now we should talk abouthow to glue an air mattress at homewhat tools and tools will be required for this. If there is no special repair kit, then any improvised materials will do:


  • universal glue "Moment";
  • patches of thin rubber;
  • alcohol or acetone;
  • fabric gloves;
  • brush for glue;
  • marker;
  • soap or shampoo;
  • water;
  • fine sandpaper.

The listed materials are almost always in the house, so it is not necessary to purchase special kit for repairs, because it is quite expensive.

How to seal a hole

Having found and identified all the defects, you can start repairing yourself. We offer step by step instructionshow to glue an air mattress:

  1. Remove the air from the mattress, straighten and carefully lay out the area to be repaired on level ground.
  2. Using sandpaper, carefully clean the bonding points on the mattress and on the patch.
  3. Cleaned areas must be degreased with any available means.
  4. Spread a thin layer of glue on the prepared surface of the product and the patch with a brush and let it dry for 10-15 minutes.
  5. Put the patch on the damaged part and let the glue dry for a day.

Important:You can put a small load on the patch. A day later, the repaired mattress is pumped with air, the tightness is checked by lubricating the repair site with soapy foam.

There is one more significant pointhow to glue an air mattress on the velor side, because in this situation the above repair technology will not work. This applies to mattresses of the popular Itex brand and other manufacturers. To apply a patch to such a product, you must do this:

  • clear the velor surface to the size of the patch. To do this, moisten the surface with acetone and clean off the pile with a dull knife;
  • wipe the smooth surface again with acetone, and then glue can be applied;
  • let the glue dry, apply the prepared patch to the surface in the same way. Press it against the surface of the mattress and let it dry for a day.

Advice!How and how to seal an Intex air mattress? The patch can be applied from the inside. In this case, the area with damage is pushed out through the valve and sealed in the usual way. The inside surface is rubber and additional processing won't require.

Repair of large holes and cuts

How to seal a hole in an air mattressif it is more than 5 mm. In this situation, do-it-yourself repairs may not be possible, it is better to entrust it to specialists. In specialized workshops, the repair of the inner part of the product, the sealing of large cuts and holes is carried out on special equipment.

Seam damage repair


Complex issuehow to seal an air mattress along the seam,experts will help you decide.

Home repairs may fail, so if there is a workshop nearby, it is better to take the mattress to the master. Seam damage is removed from the inside of the mattress.

To do this, the torn section of the seam is squeezed out through the valve, and then you can proceed with the repair, following the instructions:

  1. Wipe the rubber surface with alcohol to degrease.
  2. Leave to dry completely - during this time, cut out a suitable patch, which is also wiped with alcohol.
  3. Lubricate the sides to be joined with glue and attach them to each other.
  4. Press them tightly, leave to dry for 12 hours.

As the glue dries, turn the mattress inside out and inflate with air.This is necessary to check the quality of self-repair.

Damage prevention

To avoid further damage to the mattress, it is recommended to observe following rules operation:

  • Before throwing the mattress on the ground, remove all sharp objects or lay a dense fabric under it.
  • Do not over-inflate the product.
  • Protect the product from the claws of pets.
  • You can not drag an inflated mattress on the ground, especially when there is a person on it.
  • Do not jump or sit abruptly on the mattress.
  • The air must be released slowly.
  • Wash with soapy water.
  • Before you fold the mattress and place it in the closet, it must be thoroughly dried.

As can be seen from the above,how to glue an air bed- the process is quite simple, you can completely cope with the repair of the product yourself. Better yet, avoid such damage. But if there was a puncture, do not despair - everything is in your hands.

Air mattresses are currently very popular - they are used not only for outdoor recreation, but also as an additional bed. Today, manufacturers produce a huge number of these products. various forms and sizes. But, unfortunately, all these products have one, but significant disadvantage- they are easily damaged and can tear during operation. How to glue an air mattress on your own in order to extend its service life, and what means to choose for this, we will tell you today in the article.

Rules for using an air mattress

Inflatable furniture is a versatile product that has a lot of advantages:

  • Compactness. If necessary, the mattress can always be hidden in a closet.
  • Ease of transportation.
  • Wide selection of shapes, sizes and colors.
  • Versatility of application. You can use the mattress on hikes and travels, in the country and in the apartment, for swimming and sunbathing during the holidays.
  • Simple care.

However, in order not to damage the rubber product, it is necessary to adhere to simple rules operation:

  • Do not inflate the mattress to the maximum.
  • Keep animals away from the mattress, as their claws can easily damage the product. Dogs, moreover, can taste the object and taste.
  • Do not allow children to actively jump on rubber furniture.
  • Do not store inflatable furniture in low temperatures, since such conditions can adversely affect the surface shell.
  • Dry the product well before storing.
  • Keep inflatable furniture away from sharp objects.
  • Release the air gradually, do not press hard on the surface to speed up the process, as the seams may be damaged.
  • Before you put the mattress on the ground, be sure to inspect the surface for broken glass and sharp objects.
  • Do not pull the mattress with people lying on it over a hard surface, as this could tear the item at the seams.
  • If the product has been used for outdoor recreation, wash the mattress with mild soapy water. Do not use detergents containing abrasive components or chemically active inclusions.
  • Use the mattress as directed. If inflatable furniture is intended for sleeping, then do not use it for swimming procedures and vice versa.

Of course, sooner or later, even on such time-tested Intex air mattresses, damage can occur. Therefore, it will be useful for every owner of a rubber product to know how to seal an air mattress at home.

Types of damage to air mattresses

There are several types of defects, depending on the severity of which you will decide whether to repair an air mattress at home or entrust this work to professionals.

The main damage to rubber products include:

  • Cut or puncture.
  • Seam divergence.
  • Rupture of internal partitions.

Important! Of course, a small cut or puncture can be easily sealed on your own, but repairing such complex problems as a tear along a seam or a broken inner rib is unlikely to be within your power. The best thing to do in this case is to contact service center for help from experts. Repair of an air mattress can be carried out in the same company where the product was purchased. Many reputable companies meet the needs of customers and repair products at home.

How to detect punctures in inflatable furniture?

Finding damage in a mattress is not as easy as it seems at first glance, because the hole is most often microscopic and invisible to the naked eye. You can find a hole in a rubber product in the following ways.

Method number 1. Hearing:

  1. Inflate the mattress in a quiet room.
  2. Listen carefully. A characteristic hiss will be heard near the hole - this is the air coming out of the mattress.
  3. Carefully examine the injury site and slowly run your palm over the punched area at a height of 1-3 cm. A thin stream of air will “cool” your palm. Circle the cut with a marker.

Method number 2. Water procedures:


Method number 3. Use a detergent

Use for this method any detergent, which is quickly whipped into foam. If the product is too large and there is no point in lowering it into water in parts, then proceed in the following way:

  1. Inflate the mattress.
  2. Whisk any detergent (dishwashing detergent, soap, etc.) into lather.
  3. Apply foam to areas of the mattress that are likely to be damaged.
  4. In places of cuts and punctures, the foam will bubble.
  5. Mark the defect with a marker.

Method number 4. Powdering

Except wet ways, there is also a dry method. It is, for example, used when it is necessary to seal a velor mattress. soap solution on such a surface it foams weakly, and damp furniture, albeit inflatable, is not the most nice thing in home. Therefore, we suggest in this case to use starch, flour or other powdered easy remedy thus:

  1. Powder a dry mattress with powder at the site of the alleged puncture.
  2. The light powder will be blown away by the air coming out of the hole.
  3. Circle the puncture with a marker, and collect the powder with a vacuum cleaner.

Method number 5. Water + detergent

This is a more time consuming but effective method. Step-by-step instruction:

  1. Release the air from the mattress.
  2. Type 3-5 liters of water.
  3. Mix water with any washing liquid: liquid soap, dishwashing detergent, etc.
  4. Pour the resulting liquid into the mattress.
  5. Inflate the product.
  6. Turn the object in different directions, trying to determine the location of the cut. In these places, the water will flow out with a slight whistle.
  7. Mark the damaged area with a marker.

Important! This method detection of damage is very effective, but after it it is necessary to dry the product very carefully. In addition, on the surface of a rubber object from soap suds white streaks may appear.

Method number 6. We use stretch film

This is the most universal way detection of punctures and cuts on rubber products. Proceed as follows to check if the air mattress needs to be sealed:

  1. Inflate the mattress.
  2. Apply water to the surface of the product with a spray bottle.
  3. Lay a strip of stretch film on the wetted surface.
  4. Carefully level the film and remove air from it.
  5. In the damaged area, an increasing air bubble will be noticeable.
  6. Remove the film from the mattress. Determine the location of the cut by the gurgling and squeaking sound.
  7. Circle the damaged area with a marker or felt-tip pen.

Important! To accurately locate the hole after you have located the location, use shaving foam.

So, once you've found a defect in your air mattress, prepare a repair kit.

How to glue an air mattress?

It is best to seal an Intex air mattress with a special repair kit from the same company. Usually it comes with the purchase of the product.

The Intex rubber repair kit consists of the following components:

  • Flock patches.
  • Glue.
  • Transparent vinyl film.
  • Instructions for using the kit.

The PVC repair kit is very compact, you can always take it with you on the road. However, if such a kit was not at hand, then you can use alternative options, For example:

  • The patch can be cut from any old toy made of PVC, or any other unnecessary rubber thing.
  • Instead of glue from the repair kit, you can use:
    • Rubber adhesive made of natural rubber "Desmokol".
    • Glue for rubber boats"Uranus".

Important! Do not use to repair air mattresses instant glue, as it can further spoil the surface of the product.

In addition, for repairs you will need the following materials and tools:

  • Scissors.
  • Glue brush.
  • Fine-grained sandpaper.
  • Surface degreaser - alcohol, acetone or gasoline.
  • Soap or any detergent.

Repair of air mattresses

To properly repair a rubber product, you must strictly follow the instructions and follow the safety measures:

  • Use glue very carefully, in no case inhale it.
  • Wash your hands with soap after using the product.
  • Repairs must not be carried out near open sources of fire, since the adhesive intended for repairing rubber products is very flammable.

How to seal a small puncture or cut?

Step-by-step instruction:

  1. Prepare space for product repair.
  2. Gently flatten the damaged area on level ground.
  3. Clean the puncture (cut) site with fine-grained sandpaper. The cleaned area should be slightly larger than the cut itself.
  4. Degrease the patch area. Apply one of the means - pure alcohol, nail polish remover, gasoline for lighters. Please note that after processing there should not be any traces of the degreaser.
  5. Take a suitable patch from the Intex repair kit. If there is no such patch, then cut a circle or oval from a suitable material. The size of the patch should be 3-5 cm larger than the damaged area.
  6. Squeeze the adhesive onto the patch and use a brush to apply the adhesive evenly to both surfaces to be bonded. Be careful not to get glue into the hole.
  7. Press the patch firmly onto the damaged area.
  8. Put the repaired mattress under the press for a day. For the press, any solid object suitable for this purpose will do. In no case do not bend the product at the place of gluing.
  9. After a day, inflate the mattress and check the quality of the repair.

Important! If there are several damages, then they need to be repaired in stages, waiting until the previous glued patch dries completely.

If the defect is formed on the side with a flocked coating, then first gently clean the soft pile (velor) with sandpaper or rinse with alcohol, otherwise the patch will not stick. Then follow the instructions, but use a special patch - from flock. Unfortunately, sticking such a patch invisibly will not work, so try to stick the product from the inside in this way: using a ruler, pull the defective area to the inflation hole and turn it inside out. After gluing the patch, wait 12 hours and turn the product back.

If you did everything right, and after inflating the mattress, it still deflates, then perhaps the reason is in the valve and it was not installed tightly.

Air Mattress Valve Repair

To check for valve orifice problems:

  1. Inflate the mattress.
  2. Pour shaving foam into the valve opening.
  3. If there is damage, foam will appear around the valve.

To repair the valve, proceed as follows:

  1. Remove the adjacent valve.
  2. Pull out the rubber seal.
  3. Sand the end of the valve using sandpaper.
  4. Lubricate the end face of the valve with silicone grease.
  5. Insert the valve back.

How to glue an intex air mattress at the junction of the seams?

If the vinyl mattress has burst at the seam, there are two ways to seal it.

Method number 1:

  1. First, wash off the lint at the damaged area with alcohol.
  2. Glue the patch from the repair kit following the instructions.

Method number 2:

  1. Finding a defect, using your hands and a ruler, pull the damaged area through the hole in the valve.
  2. Wipe the cut with alcohol.
  3. Dry the cleaned area.
  4. Cut out rubberized fabric required size patches.
  5. Apply to inside glue patches.
  6. Apply the patch to the damaged area.
  7. Press the patch firmly against the surface of the product.
  8. Leave the mattress for 12 hours to dry.
  9. Turn the mattress inside out and inflate.

Important! Do not repair on your own if the size of the damage exceeds 5 mm or there is a problem with the internal partitions. Such damage is almost impossible to fix on your own. Contact the service workshop and the specialists will assess the existing defects and, if necessary, restore the product by replacing the section of the old canvas with a new one.

What else to read

Compliments in Estonian Russian-Estonian phrasebook: how to explain yourself in an unfamiliar country. Popular phrases and expressions for travelers....
Help Beltelecom on settlements Belarusian mobile operator Beltelecom, under which it offers Internet access services....
Exactly a month has passed since the disappearance of the schoolboy in Pushcha Alyaksandr Lukashenka's abilities could be useful in solving the disappearance of 10-year-old Maxim Markhaliuk, a resident of...