Any hood is equipped with a filter that absorbs grease, fumes and unpleasant odors. If you ignore pollution, it will cease to perform its functions. In order not to waste time removing a huge layer of dirt, clean the hood at least once a quarter. You can get rid of it in 15-20 minutes, and our article will help you with this.
You can start cleaning only after turning off and partial disassembly unit. For faster preparation, we recommend that you read the manual for your hood model. After turning off the device, you can proceed to the analysis:
Most often, this panel is a metal grease filter. It is cleaned with fat-soluble detergents, which will be discussed below.
The instructions should indicate how often such a filter needs to be changed. It is usually recommended to replace carbon filter for a new one every 3 months of active use of the plate. You can buy a new consumable in the store household appliances, order in service center or directly from the manufacturer via the Internet.
Even if you wipe the hood, it is still not protected from grease, which you can fight with the following instructions:
See how it's applied this method, and what results can be achieved, you can in the following videos:
Each of the methods described below is effective, it all depends on your "arsenal":
The hood filter can be washed in the dishwasher using your usual detergents.
Sewer drain cleaner reacts with hot water, forming chemical vapors and heating up. Therefore, the use of this product should take place in a well-ventilated area, or try not to inhale the vapors emitted.
In the following video, the hostess will share the method she uses to clean the hood filter:
You can also clean the hood from fat using a steam generator. The extract is processed with steam, as a result of which the fat softens and is easily washed using a sponge and soap solution.
Be sure to wipe the surface with a dry cloth to avoid leaving streaks.
We hope that the recipes, along with the video, helped you get rid of the layer of grease and dirt that covered the hood filter. If something is constantly fried in the kitchen, it is recommended to clean the filter once a month - it will not get worse.
In contact with
The hood in the kitchen is an opportunity to rid the room of fatty fumes and odors that can nourish the entire apartment. But sooner or later you have to clean it. Of course there are special chemicals intended for these purposes. But more and more often, housewives are wondering how to wash the hood from fat folk remedies. There are many options!
Before you start cleaning the hood in the kitchen, it should be prepared for this. Accordingly, you need it:
ATTENTION! Before starting the process, be sure to read the instructions for the hood. And don't forget to turn it off. Otherwise, there is a risk of electric shock or short circuit.
The analysis of the hood for washing it is carried out in the following order:
ATTENTION! It is very important to find information about the air filter in the instructions for the hood. Not every type of it can be cleaned.
The hood is very easy to clean. Any tool will work for this. You can even simply dilute the powder, soap or dishwashing detergent in water and wash off traces of grease with a sponge. After that, the entire surface is wiped with a clean cloth. But how to wash the hood mesh from fat is another question. There are many ways here.
Methods for cleaning greasy and dirty stains from the hood and its filter mass. You can use purchased products, which in their composition have a variety of chemical elements. Among the available store tools:
And someone tries the most diverse available folk remedies, time-tested:
And, of course, in the fight against grease on the hood, you can’t do without brushes, rags, sponges.
Many housewives agree that laundry soap is one of better ways how to wash the grate of the hood from fat. At the same time, the content fatty acids in such soap should be at least 72%(this figure is usually written directly on the bar).
Prepare the cleaning solution as follows:
If suddenly the pollution did not disappear the first time, the procedure can be repeated once again.
An indispensable tool - lemon, or rather its juice, will help to remove fresh fat from the hood. To do this, it is enough to carefully rub all the greasy surfaces of the hood with its pulp. In this form, they are left for 10 minutes. After - everything is erased with a regular napkin. Such a tool does not always help the first time. Therefore, you need to keep in mind that you will have to repeat the procedure a couple more times before the final cleaning of the hood.
A rather difficult question is how to wash the kitchen hood from fat, which is already outdated. Acid can be used for this. The most affordable for us is vinegar. It can be used both in a concentrated, undiluted form, and in the form of a weaker aqueous solution.
It is enough to dilute 2 parts of acetic acid in 1 part of water. All the necessary surfaces of the hood are wiped with this solution and left for 12-15 minutes. After this time, all residues of contaminants are removed with a sponge and clean water.
IMPORTANT! Because Since the product involves the use of concentrated acetic acid, it is recommended to work only with gloves. They need to be thick. The product should not get on the skin or in the eyes!
A heavily soiled hood can be washed off grease stains using a conventional baking soda. For such folk recipe would need:
The result is a crystal-clear and clean hood!
ADVICE! If the pan is not large enough to completely fit the grate, you can clean first one side and then the other by turning it over.
If the hood is in a completely neglected state, when neither soda nor vinegar helps, then how to quickly wash the hood from fat? It is possible to correct the situation with the help of aggressive pipe cleaners. It can be a granular preparation, powder, liquid or cream.
The hood grate is placed in a stainless steel container. From above, it is carefully poured or covered with a purchased product to remove blockages in pipes. Now you need to carefully pour warm water on top. After 10 minutes, when the grate is already soaked, the fat begins to move away, the solution is drained, and the filter is washed with warm running water.
ATTENTION! Pipe cleaner is a harsh chemical. It should be used no more than once a year. Otherwise, the lattice, made of metal, will gradually begin to collapse.
Today in stores you can find a wide variety of products that are designed specifically to combat greasy old pollution in the hood. It is enough to buy one of them (domestic or foreign production) and use it.
To do this, the grate, on which fat accumulates, must be placed in a large container. From above, its surface is poured with a special cleaning agent. Lattices can be laid in layers, also treated with a tool. In this state, they should be kept for at least 20 minutes. Then they are thoroughly washed in water.
If the drug has not completely coped with the dried fat on the hood, you should not worry. It is enough to repeat the cleaning process again.
Each housewife can choose for herself the most suitable remedy than to wash the hood in the kitchen from fat. Just gotta try different variants. But don't try to use these harsh chemicals often. Better - once a month or even less often. Otherwise, you can simply damage the hood.
Faced once with serious old greasy stains on the hood, housewives dream of facilitating the process of washing them. But is it really that simple?
Highly effective recipe how to clean the filter kitchen hood from fat is presented in this video:
Whatever one may say, but to clean at least something from the dried and chronic fat, this is not something that is not simple, and sometimes even seemingly completely unrealistic. Therefore, every good housewife knows by heart that the hood is on own kitchen you need to wash it immediately, as it gets dirty, because then you will have to make much more effort. And it’s worth saying that it’s actually difficult, but the most experienced and experienced housewives, wake them up even in the middle of the night, will tell you exactly how and with what to wash the fat from the hood over the stove so that the kitchen sparkles with cleanliness and order.
Professional chefs, or housewives who most they also spend their lives in the kitchen, they know for sure how quickly the hood over the gas one gets dirty, and over electric stove also. It would seem, well, what’s wrong with that, let it stand until it becomes completely dirty, but it’s not worth doing this at all. Firstly, the hood protects the house from all the burning and smoke that inevitably arise during cooking, and secondly, it will be simply impossible to pick out the frozen fat later. Therefore, in no case should you delay and put off the process indefinitely, but it would be optimal to wash the hood often, but with a degree of ease and a sense of accomplishment.
Moreover, when the hood is clogged and dirty, it simply stops performing its functions as it should, and all due to the fact that the filters are simply overgrown with layers of sticky and nasty fat, which does not want to get out of there at all and scraping it off will not be easy at all . How to clean the hood over the stove in order to protect yourself and your loved ones from harmful fumes, fumes and burning, as well as unpleasant odors. Moreover, it is worth saying that not even in a restaurant or a cafe, but in ordinary apartment, the hood should be cleaned approximately twice a month, in extreme cases, once every thirty days, but it all depends on how much and how often you cook.
It is clear that you can wash and clean the hood over the stove in the kitchen only when you clearly understand what to do. First of all, you should understand that without an instruction that would explain everything in detail point by point, you definitely won’t be able to cope for the first time, and the maximum that you can do is wipe all the outer surfaces. It is clear to figure out how to clean the hood in the kitchen from fat , you should first prepare, for example, to study its design, since the gadget will have to be disassembled.
Important information
If you think that all filters in hoods are subject to mandatory cleaning and washing, then you are greatly mistaken. There are models that can only be changed, and it is simply not possible to wash such filters. That's why this information you need to initially draw from the same, good old instructions, which we often begin to read only when the “subject of study” is already broken.
When everything is taken apart and necessary items for washing are collected in one place, it is worth proceeding specifically to the question of how to wash the stainless steel hood from fat, which clings firmly and reliably to its walls. In fact, if you know the aspects, subtleties and nuances, then it will not be difficult to do all this, but you will have to make enough efforts to bring the matter to its logical conclusion. Next, you will need to finally decide how to clean the kitchen hood filter from fat, and great help can come to us familiar remedy from the set of household chemicals of any housewife - cleaning powder for stoves and ovens, but there are also good old, proven over the years, tools.
There are many options, here are just a few. And, of course, you yourself will choose, and the employees of the household chemicals store, who are usually perfectly familiar with their own assortment, as well as with the nuances of using a variety of products, should give advice.
It is clear that the choice of how to wash the stainless steel hood from grease largely depends on the assortment of the store where you are going to purchase professional or household cleaners. Moreover, it should be understood that high-quality and really effective remedy it can't be too cheap, so get ready to fork out.
It is the hood filters, as well as the grilles, which are most often made of stainless steel, that are the main obstacles that stop dirt, grease, dust, and fumes that occur when cooking. However, small grates are extremely easy to clog with the same fat, after which the efficiency of the hood drops significantly. Having disassembled the hood and prepared everything for cleaning it, it will immediately become clear that the most difficult question will be how to clean the hood grid from fat, especially if it is already thoroughly dried up. To determine whether it is worth resorting to drastic measures of influence immediately, or you can do without them, it is not at all necessary to run to the experts, a visual inspection will be enough.
So, if the droplets of fat on the surface of the mesh are light enough, then they have not yet had time to harden, and therefore it is quite possible that you will have to get out of the difficult question of how to wash the extractor hood in the kitchen from fat. The very first and simplest method is quite simple, so even those who see this amazing contraption for the first time can figure it out.
If, for various reasons, the fat has already solidified thoroughly, turned dark brown, and ordinary cleaning does not bear any fruit at all, you will have to use more drastic means of dealing with dirt. In this case, the question of how to clean the grate of the hood from fat is becoming more and more relevant, and we suggest using the old and proven method that our grandmothers used to wash old pans and pots from the remnants of adhering fat, namely, digestion.
Thus, it turns out that washing the filters, as well as how to clean the grate from the hood, is not at all so difficult, although this is a rather laborious process that will require special efforts and attentiveness, because you have to mess with hot water and a variety of chemically active reagents.
note
If, after boiling, you notice grease residues on the filter surface, the procedure can be repeated or simply extended. Moreover, radical measures in the form of alkaline purification should be addressed only as a last resort, because the metal can simply collapse from frequent use.
When hands are already falling, and all the methods of how to clean the hood in the kitchen are simply and “painlessly” exhausted, the time comes for drastic measures. Apply this method cleaning is not possible often, since this process can damage the grids and filters themselves, which is not at all desirable. Therefore, it is better to try not to bring the equipment of your kitchen to such a deplorable state. However, talking about it if nothing helped is stupid, but for the future it is worth making a mark in your schedule and allocating time for the timely cleaning of hoods and other kitchen utensils.
You need to leave the bars for five to seven minutes, and after all, simply rinse with plenty of cold water. Then everything is simple, dry the parts of the hood thoroughly, assemble the unit, and feel free to use it, the main thing is to avoid strong pollution anymore, washing the hood from fat and burning in time.
Video "How to clean the kitchen hood from fat"
If your house has a hood, then you should think about the last time you looked under its dome or checked the filter for purity. If you did this a few months ago or are just about to do it, then you should be prepared for the fact that the view will be intimidating. The filter in the hood performs the role of collecting grease, fumes and odors, therefore, while doing its job properly, it will become dirty at the very a short time intensive use of the equipment.
On the surface of the filter, you will be able to see a fairly thick layer of dirt. Over time, the filter can become contaminated to the point where it becomes ineffective. To avoid this, it must be cleaned periodically. You can get the job done at home. If you wondered how to wash the hood from fat, then you should know that such work should be carried out at least once a quarter. And if you often cook, then they can be repeated once a month.
Cleaning the hood starts with preparatory work. To do this, the device is turned off and disassembled. You must first read the instructions for the equipment. Before you start cleaning, you need to dismantle the cover, which is located above the stove. To do this, the latches are disconnected, only after that you can remove the element from the grooves.
Next, remove the filter and remove the pipe that connects the vent to the hood. She, too, will have to be washed of fat. Next, you can also remove the air filter. The body of the equipment should also be checked for contamination.
If you have thought about the question of how to wash the hood from grease, then you should know that the filters can be washed in the bath by soaking them in a dishwashing detergent solution. Concerning air filter, then it does not always need to be cleared. You can always find information about this in the instructions.
The surface of the hood must be thoroughly cleaned. For this, standard detergents and a sponge are usually used. The composition must be diluted in water using a ratio of 1 to 4. The sponge in the product must be moistened and wiped with the surface of the device. After cleaning is completed, the base is wiped dry so that there are no streaks left. When it comes to the filter, you can experiment with cleaning it, because there are a lot of ways to do this.
Before washing the extract from fat, it is necessary to choose a technology that will provide for the use of an appropriate product. The most popular solution will be fat-dissolving products that are used for washing dishes. The filter is soaked in the composition, and after that it can be wiped with a brush or sponge, doused with boiling water at the final stage. The effect can be achieved only if the pollution is quite fresh.
The filter can be cleaned with a soda solution. This approach is the simplest, safest and at the same time the most effective. Quite often, housewives wonder how to wash the hood from fat. To do this, take a large pot, fill it with water and put on fire.
As soon as the water boils, you should pour soda into it in a volume of 1 cup. When all the soda is at the bottom, stir it well and place the filter grate in the pan. The element should be boiled for half an hour until the contamination is gone. If the capacity is large enough, then the procedure can be repeated by turning the filter over. At the final stage, you will need to wash the pan.
You can clean the grease filter with soap. A 72% composition is perfect for this. To carry out the work, you will need 0.5 pieces, hot water and a grater. The bar of soap is rubbed so that it can be dissolved in hot water. A sponge is wetted in the product. She should wipe the surfaces of the hood and the filter. A metal scraper will allow you to get rid of old contaminants.
You can use at home a product prepared on the basis of vinegar. It is important to be careful when doing this, since the remedy cannot be called safe. For protection, use rubber gloves. For cleaning, use a cloth soaked in acid. All contaminated areas must be thoroughly wiped, wetting the surface.
Vinegar is left on the base for up to 7 minutes, if the pollution is quite impressive, then this time can be extended to 12 minutes. undiluted acetic acid can be used for old stains. If the spots have appeared recently, then a solution with water should be used, which should be prepared in a ratio of 1 to 2.
If you also wondered how to wash the hood in the kitchen from fat, then you can use lemon juice. To do this, prepare two fruits, which are peeled and cut in half. The surface of the hood should be cleaned with pulp. The base is left for 10 minutes, after which you can remove dirt with a soft, damp cloth.
If the fat has formed on the hood with a rather impressive layer, then the procedure can be repeated several times until a positive result is achieved. If you still don’t know how to wash the hood in the kitchen from fat, then you can use radical method, which involves the use of a means for cleaning the pipeline. However, experts do not recommend using this technology too often. For the entire life of the hood, this method can be resorted to only a couple of times.
However, if the filter has not been cleaned for a long time, and the fat is clogged in its cells thoroughly, then this method will help you out. In addition to cleaning drainpipes, you will need a stainless steel container. Well, if the kitchen sink is made of stainless steel.
The tool should be prepared according to the instructions. It is poured into a closed sink, and then the filter is placed in the composition, not forgetting to wear gloves. You will see the reaction, after that the mesh will only need to be washed several times under running water. This method uses alkali, which can act quite aggressively on metal elements.
Some housewives are wondering how often it is necessary to clean the hood and its elements. It all depends on how often you cook. If the stove is used every day, then the hood should be cleaned once every three months. Otherwise, once every six months will be enough. However, more frequent cleaning procedures will make it easier to deal with fat deposits, because old stains are firmly eaten, this is especially true for metal mesh.
If you wondered how to wash the hood mesh from fat, then you can put it in dishwasher, the temperature should be as low as possible. Use a gentle cleaner for cleaning. If you decide to manually clean the mesh, it will be enough to use traditional cleaning agents that are pre-dissolved in warm water.
An alternative solution for cleaning the hood elements can be a solution of soap and soda in water. After boiling the grate, it will be easier to clean it of fat. This process usually takes 5 to 10 minutes. Turning the grate over to the other side, the procedure should be repeated. But it doesn't end there. After boiling is completed, the grate is soaked in the solution that remains after the procedure.
Instead of a saucepan, you can use a large basin. The grate is left for several hours, only in this way it will be possible to remove old contaminants. A tool for this can be a brush or rag, but it is important to try not to damage the part itself. Sometimes long soaking and boiling is not enough, in this case you can use ammonia, which is a reliable and proven remedy.
If you are faced with the question of how to wash the extract from fat at home, then half a glass of alcohol should be diluted in 3.5 liters of water, after putting on a mask or respirator. In the room where you plan to carry out these works, you must open the windows. A filter is placed in the hot solution and left for several hours. As soon as the dirt begins to move away, it can be removed with a stiff brush, but the intensity of the impact should not be such that it could lead to damage to the part. The filter at the final stage is wiped with a dry cloth.
If you are also one of the owners who are thinking about how to wash the hood from fat, improvised means will do you a good service. Bleach acts as another method, it helps to get rid of dirt not only in the filter area, but also in the housing area. To begin with, contaminated places must be moistened with water, and after applying whiteness, it is most convenient to use a toothbrush for this. After 10 minutes, the agent and scale residues are removed with a sponge, and the elements can be washed under running water.
Of course, it is important to know how to clean the kitchen hood filter from grease. But such pollution can be avoided if you follow the rules for caring for a household appliance. Splashes of grease can be removed from the surface of the appliance every time after cooking with a soft cloth. To carry out such work, you should choose the right one with which the care of the hood will not be too difficult.
When there is no dishes on the stove, the gas should not remain on, in addition, the hood should be cleaned only after it has been turned off from the stove. electrical network. The installation of the hood should be entrusted to a professional, because otherwise the device may be located too close, which will provoke the appearance of a fatty layer much earlier than one would expect.
If you are faced with the task of how to wash the kitchen hood from grease, then you can use the effect of steam. To do this, you need a steam cleaner, into which water is first poured. At the next stage, the device is connected to the network, and then you only have to drive with your hands. There are such models of steam cleaners, complete with which special napkins and nozzles are supplied. They will help with cleaning the hood.
Among the most FAQ, which arise in the head of housewives who monitor cleanliness, one can be distinguished: how to wash the extract from fat with soda. To do this, the powder can not be dissolved in water, but simply wipe the contaminated surface with it. However, it is first important to make sure that the abrasive particles do not damage the substrate.
Once the surface has been wiped with baking soda, you can clean it with water using a sponge or soft cloth. Now you know how to quickly wash the extract from fat. In order to achieve a positive result, you can use several tools in combination or decide which technology suits you more than others.
Impossible modern kitchen imagine without hood. This is not a decorative item at all, but an important one. household appliance. It is installed directly above the stove or hob and is designed to suck in air mixed with the smells of cooking food.
Very often, housewives forget to turn on the hood or consider it unnecessary. However, one must understand that during cooking, small particles of soot and fat in this case settle on the walls and furniture. Over time, the entire kitchen becomes covered with a sticky, dirty yellow coating, and not only spoils appearance furnishings, but also furniture.
If the hood is used constantly, then it needs regular and thorough maintenance.
From time to time it becomes clogged with grease and layers of dirt, and its efficiency drops noticeably. In this case, you need to replace the filter, or if it is a stainless steel mesh, then clean it. This business is messy and messy. It is recommended to wash the hood 1-2 times a month, otherwise it is very difficult to get rid of the greasy layers.
Sections of the article
Any kitchen air purifier must have a grease filter. It is designed to clean the air flow passing through the device from small suspended fatty particles. If it weren't for him, it wouldn't have been a month internal surfaces the hoods, including the engine, were covered with a layer of oil suspension.
The grease filter can be disposable and reusable - it is clear that the latter type is better and more practical. Disposable models are made of synthetic winterizer, acrylic or non-woven fabric and are most often installed in low-cost flat-type structures. Such "rugs" made of synthetic fabrics are thrown away as soon as they become dirty.
Disposable fat "catchers" cannot be washed, they lose all their properties from washing. That is why they are disposable.
The use of an "updated" product in this way is fraught with engine breakdowns.
But the metal grease filter will last as long as the hood itself - it is distinguished by quality, safety, reliability and durability. Such designs are better because they do not need to be replaced, but only require periodic flushing.
A traditional grease filter is a cassette in the form of a metal frame and a mesh element made of foil (in the form of a grid or with perforation). The perforation here can be uniform or asymmetrical, and the provided cells are necessary to change direction. air currents. This allows you to retain fat particles on the surface.
Grease metal filter can be made of aluminum, galvanized steel or thin stainless steel. In high-quality technology, aluminum is additionally anodized, which protects the product from oxidation. Such structures can have several layers or be made in the form of several modules.
Two or three separate cassettes are easier to clean - they are easy to remove, wash and return to their place.
A stainless steel grease filter is considered better than aluminum, as this material is characterized by a longer service life. In addition, products of this type purify the air more efficiently.
If we are talking about recirculation models that purify the air in the kitchen and send it back to the room, then here in without fail a charcoal filter is provided for the hood. After all, in such models it is important not only to remove soot and grease, but also to clean the air from foreign odors.
The installation of a coal "catcher" is provided behind the grease catcher. This element is based on a high-quality adsorbent, Activated carbon. It perfectly absorbs all smells.
It should be remembered that in the recirculation mode throughput hoods drops by 15-20%, and the installation of an absorbent article further reduces it. If the coal adsorbent accumulates pollution in itself, then the air will pass through it worse and worse.
The carbon filter for the hood is often not included in the basic package, and is purchased separately. In addition, this is a replaceable element that will have to be purchased as it wears out constantly.
Outwardly, such an element may look like a rectangular cassette or a circle. The case in the product is plastic, and the coal is held by a special mesh. Activated charcoal is available in the form of powder or granules.
The more total area absorbent particles, the better the "catcher" works.
Due to coal compacted in one place, the efficiency of the hood drops. The process for replacing the carbon filter is as follows:
Source: kitchendecorium.ru
How often should the carbon filter be changed? If you have opted for a hood that works in recirculation mode, the requirements for air purification increase. After all, it is necessary not only to collect soot and grease, it is necessary to clean the air from the smallest contaminants that manifest themselves as odors. It's pretty fine work which they can handle charcoal filters for hoods.
They are located behind the grease filters. The basis of the carbon filter, as you might guess from its name, is activated carbon - a well-known absorbent. It absorbs well and holds it securely inside. harmful substances. The only drawback is that these filters need to be changed quite often, and they cost from 250 to 2500 rubles, depending on the quality and the manufacturer.
The Kuppersberg carbon filter is one of the best models on the market The quality of the carbon filter depends on the operation of the entire unit. In the recirculation mode, the filter capacity decreases by about 20%. This is due to the fact that the movement of air inside the filter is difficult.
Carbon filters vary in density, and the more it is filled, the slower air passes through it.
Therefore, do not forget to change cartridges in a timely manner.
On average, charcoal filters for hoods serve 3-4 months, but different manufacturers give different recommendations regarding the service life. So, Elica filters are recommended to be changed every 2 months. Cartridges from Elikor, Jetair - once every 3-4 months, depending on the frequency of use of the hood.
After all, you can turn it on every other day for half an hour, or you can turn it on every day for three hours. Falmec filters - use 4 months, Fabriano - 4 to 6 months, Krona - 6 to 12 months, Gaggenau should be changed twice a year, and Bosch filter - 1 time per year. As a rule, additional carbon filters for the hood are not included in the package of the device.
If you leave the hood on after each use for another 5 minutes, you can extend the life of the charcoal filter. So the rest of the moisture is removed from it, and the coal does not cake and retain a high adsorbing capacity.
Source: kitchenguide.su
In order not to spoil an expensive device, it is recommended that you first study the instructions for it, which gives clear instructions on how to wash the device. Modern hoods may have their own cleaning system, which will simplify cleaning procedures.
Most often, the principles of washing and cleaning the kitchen hood come down to the following actions:
Most often it is mounted on latches, but if necessary, unscrew the mounting bolts. Try to put the bolts together so that you can assemble the device later.
The outer panel must be washed using detergents, in filmed it will be much easier to wash it from fat than in the one attached to the hood.
Now that all the parts are removed, you can go directly to the hood itself. Drops of hardened fat and dirt are usually present on its surface from all sides. Using detergents, it is necessary to wash off all the dirt, remove soot and grease, and prepare the device for assembly.
Once you have managed to wash the filter, pipe, outer panel and the hood itself from grease, assemble the appliance and prepare for further work. This washing method is applicable to heavily polluted air exhaust devices, but if the pollution is not of such a terrifying nature, then you can limit yourself to washing the filter.
Source: ubirai.ru
There are many ways to wash grease from the filter (grille) of the hood:
The easiest way to wash grease from the hood is to put the filter (grid) of the hood in the dishwasher, pour the appropriate detergent and turn on the unit at minimum temperature.
This method is similar to the automated version. It will require a steam cleaner. The equipment is expensive, but it makes life much easier in the field of any cleaning. Water is poured into the steam cleaner, it is plugged into the network, and then only drive with your hands ... The steam cleaner usually comes with several nozzles and special napkins. Their use is described in the instructions for the unit.
After boiling, the water in the pan will be yellowish in color. If the contamination is partially removed, we recommend repeating the operation again.
Grandma's old way! Many people remember how Soviet time mother or grandmother folded metal kitchen utensils into a huge pot called "dumping" and boiled for several hours in soapy water. The plot is the same:
A fairly easy and inexpensive way to wash the hood from grease if there is a large pot in the house that can accommodate the filter (grid) of the hood. A little time and effort will be spent:
The result of the work is a clean hood in almost original condition. The same easy and inexpensive way to wash the extract from fat is associated with the use ammonia with a large saucepan.
Everything is very carried out just as easily as in the previous version, the problem is only in the “flavor” that eats out the eyes. This method will help if the pollution was strong and you could not wash off the fat with soda:
Our stores are filled with a variety of household chemicals. This method cannot be called cheap, but it is quite fast. To clean the hood from grease, you can use:
You will have to put in effort and time, but without investing a lot of money. You will need liquid whiteness, a toothbrush and rubber gloves.
Stages of work:
There are facilities for cleaning waste water and sewer pipes. These products can very well wash grease from the hood, but their use contributes to the destruction of the metal. This is the risk - to be left without a hood! The process is quite simple:
kayabaparts.ru - Entrance hall, kitchen, living room. Garden. Chairs. Bedroom