Tire beds with your own hands with a step-by-step guide. How to paint flowerbeds made of tires or other materials

The desire of a person to decorate the territory of his dacha, to create a wonderful, cozy environment with the use of things at hand, contributed to the emergence of many design ideas.

The original material for the implementation of extraordinary ideas is old car tires.

Entertaining crafts from tires for the garden will decorate both flower beds and playgrounds, as well as paths. Tires and tires can be used not only to create elements of garden decor, but also for practical purposes - they can be used to build a pool, furniture, swings, a sandbox, a bicycle parking lot.

The photo below shows extraordinary tire craft ideas.

Idea #1. Making a flower bed out of tires

Most easy scheme- we take an unnecessary tire, fill it with soil and plant plants. Of course it won't be unique. decorative element garden design.

To fix everything, we take bright colors(acrylic or oil-based) and paint the tires. Next, we put them on top of each other, resulting in a multi-tiered flower bed.

The original solution would be a vertically arranged flower bed, folded in the shape of a pyramid. We fall asleep inside the soil and plant curly flowers - petunias or strawberries. On top you can put a pot with a single plant.

From tires you can make and hanging flower bed. To do this, you need a steel chain - it will need to be attached to the tire and hang the entire structure on a tree.

In order to prevent the soil from waking up, cover the bottom of the tire with a dense sheet of rubber or other suitable material.

An unusual solution would be to make flower beds in the form of a teapot and cups. All you need is a few tires and scraps of metal tape and pipes.

Idea number 2. Tire figures

Another kind of tire crafts for the garden are a variety of unusual and intricate tire shapes. They will revive your garden and improve the mood of all household members.

The figure of a swan is very popular. To make it, you need a tire without a steel cord. It needs to be marked first.

For cutting, use a well-sharpened knife. We fix the swan neck with a metal rod. The final step is to cover the resulting product with white or black paint (depending on which swan you want - white or black).

It is enough just to create a funny horse, zebra or giraffe. Such figures will require installation in the ground wooden beam medium size with tire.

Crafts should be painted in colors corresponding to one or another representative of the fauna.

Old tires and basins are easy to turn into a frog or a cute turtle. A bit of imagination will help to make interesting and unusual installations.

Note!

Idea number 3. Country furniture

In the garden, pieces of furniture made of tires will look great.

They can be made in various styles and the use of different upholstery materials, ranging from leather and textiles to wicker and wire.

The tires will make a comfortable chair, in which it will be wonderful to relax in the bosom of nature. To do this, take the tires, wrap them with interlaced straps and ribbons. It won't take long, and the result will be entertaining.

Furniture for summer cottages can be made from different-sized tires of medium and low hardness.

Tires make beautiful tables, ottomans, armchairs, chandeliers, fountains and wash basins.

Note!

Idea number 4. Tire swing

Swings are an integral part of any playground. Tire swings are safer than wood or metal swings. It's easy enough to make them.

You will need:

• strong horizontal branch;
• sharp knife and jigsaw;
• chain or strong rope;
• tire.

We tie the end of the rope into a loop, the knots must be strong and reliable. We throw the loop over the branch, pass the rest of the rope through it and tighten it. Tires are placed perpendicular to the ground.

We pass a rope through them and fasten it at a height of approximately 0.9 m from the earth's surface. The swing is ready!

Idea number 5. Tire track

Paths created from unnecessary tires, or rather from their tread part, look unusual and original.

We bring to your attention a selection of photos of various crafts from tires.

Note!

Tires are universal material to create a wide variety of things with your own hands.

Numerous tire craft workshops can be easily found on the Internet. Therefore, if you have unnecessary old tires lying around, feel free to put them into action, creating memorable elements of garden decor.

Photo crafts from tires

The problem of recycling used tires has been of concern to environmentalists since the late 70s of the last century. This is especially true for our country, where there are not yet a sufficient number of enterprises capable of using them as recyclable materials. As they say, in such a situation, everyone is saved as best they can, so we can only welcome those craftsmen who are trying to free landfills from these non-decomposing wastes and, for example, make flowerbeds from tires with their own hands. They can be very different, from worn tires simply dug into the ground, in which flowers are planted, to complex flowerpots in the form of swans with a bright pattern. If you are interested in this idea and want the area in front of your house to be decorated with a beautiful tire, you can read below how to make one with your own hands.

Which ones to use

If you have a choice, then a complex DIY tire bed, the manufacture of which involves cutting out shapes, will look better if you use foreign-made products, as they have thinner and more pliable rubber. In addition, it makes sense to give preference winter tires, as they are more textured, and worn tires. The fact is that the worn proctor is softer, so the eversion process is easier and does not require much effort.

"Flower"

To make original do-it-yourself ones, you just need to take 4 any tires, preferably the same size. You will need to remove the rubber from the metal rim and cut it so that you get two identical halves. So you need to do this with three tires, and for one, leave the rubber shell intact, as it will be used as the core of the flower. Then the halves and the whole tire must be painted in different colors and dug 5-6 cm into the ground, laying out a flower with 6 petals with a round center. The composition will look more interesting if the core is planted with flowers of one type, and the petals of another.

Pyramid flowerbed

This one is very simple and beautiful option flowerbeds made of tires, made by hand, suitable for plots or yards with a small area. For its implementation, you will need 6 tires that need to be painted in bright colours and lay in 3 rows, in which there will be 3, 2 and 1 tire. If a country cottage area quite spacious, you can make the design more complicated by laying out a flower of 5-6 tires in the bottom row, of 3 on the second and crowning it with one. Such a pyramid will look especially impressive if you choose a plant with large leaves for the upper "vase".

DIY flowerbeds from car tires in the form of a vase

There is more difficult option, the implementation of which will require a lot of patience. However, the result is usually simply excellent.

So, in order to create original flower beds from tires with your own hands in the form large vases resembling open flowers, you must:

• Put the tire on flat surface and with chalk draw the petals of the desired shape around the entire circumference. In this case, the size of each petal should not exceed 12 cm.
• cut blank sharp knife or with a jigsaw along the marked contour. To facilitate this task, you can apply a little liquid soap to the knife from time to time.
• Make longitudinal cuts along the grooves of the tread at a distance of about 10 cm.
• Using a grinder, make several cuts along the outside and smoothly cut the rubber with an indent of 15 cm. If everything is done correctly and the grinder touches the metal cord, white smoke should be emitted.
• Turn the tire inside out so that you get a kind of flower on the leg.
• Decorate using enamel, oil or nitro paints.

To make a flowerbed of tires made with your own hands even more beautiful, you can apply an ornament or stick various decorative elements on top of the base layer of paint using a stencil.

pyramid slide

If you have 3 tires of different sizes, or at least two and one plastic bucket with a capacity of 0.5 liters, then you can make a pyramid according to the principle of a well-known children's toy. To create it, the tires need to be laid on top of each other in descending order of diameter, stuffing each with earth. From above you need to install a bucket and land in it and in the tires from the lower layers climbing plants, so that they hang down from the hill as they grow, covering it all.

Flowerbed-"cup"

A flower bed of tires, made in the form of a cup with your own hands, will also look original. Moreover, if the place allows, then on your site you can even install a whole tea set.

For such crafts, first of all, you need to make the lower part, which will depict a saucer. You will need a tire from a truck, which needs to cut the sidewall with an electric jigsaw (to make work easier, it is recommended to cool the jigsaw blade from time to time in soapy water). Having finished this work, they take the R13 tire and cut off the sidewall with a well-ground, or even better, shoe knife, lubricating the blade liquid soap. After that, the tire is turned inside out so that the tread is inside, and a bowl without a bottom is obtained. The next stage is the manufacture of the upper part of the mug, for which you need a tire of a slightly larger diameter, for example, from an UAZ. Both sides are cut off. At the same time, on the one hand, it should be done so that the resulting hole is no larger than the diameter of the "bowl". In addition, a strip for the handle is cut out of the scraps of the largest tire.

When all the details are ready, you should start painting and assembling the flower bed. To do this, the "saucer" and the handle are painted in one color, and parts of the mug in another. Further, at the place where they are going to install a flower bed, they lay a piece of cellophane and put a "saucer" on top, and first a "bowl" is installed in its hole, and then upper part mugs. Then, with the help of self-tapping screws, the handle is fixed and, using a stencil, mugs are applied to the mug in the color of the "saucer". All! Now you know how to make a flower bed out of a tire with your own hands in the form of a cup. It remains to fill it with earth and plant flowers.

"Pig" and "Ladybug"

If you are interested in the question of how to make it simpler with your own hands, but so that it looks original, you can use your imagination. To do this, you can simply remove the "gum" from the rim, turn it inside out and paint it accordingly. For example, if you want to appear on the site ladybug, you can paint the tire red, apply black dots using a stencil and draw a muzzle with eyes. You can also make a funny piggy by painting an inverted tire hot pink and attaching a spiral tail cut from a plastic bottle. After the earth is filled up in such a flower bed and plants are planted, you need to cut out a head with ears and a patch from a piece of rubber from another tire and insert it inside the tire circle, between the flowers.

Flowerbed-"frog"

A flowerbed made of tires, made with your own hands, can be the most different shapes, for example, resemble a frog. For such crafts you will need:

• three used car tires;
• two lids from kilogram buckets of ice cream or ghee;
• enamel PF green, yellow or red;
• self-adhesive colored paper;
• hose;
• awl;
• sponge;
• wire.

How to make a flower bed "frog"

The manufacturing process is very simple: tires need to be painted in green color and, if desired, apply yellow rims on top. Then install two tires in the chosen place, and on top, between them, the third. From the hose, also painted with green paint, it is necessary to cut two segments about 1 m long, and from another tire - 4 paws and lay two in front of the lower tires, and two between them, having previously attached "hoses" to them. When the body of the frog is ready, you need to move on to the design of its head. To do this, you need to draw eyes on the lids of ice cream buckets, and a mouth on the top tire with red paint. After that, it remains just to fill up the ground and plant flowers. If you wish, you can turn the frog into an enchanted princess by making her a crown from a plastic bottle painted with yellow paint.

"The sun"

Many summer residents are interested in do-it-yourself in the form of the sun. For such a craft, you will need one tire, bright yellow paint and several plastic bottles. The tire must be removed from the metal wheel and buried in the ground so that only a semicircle remains above the surface.

Then, on the tire, you need to make holes with a diameter equal to the size of the necks of plastic bottles, and, after lubricating them with glue, screw them into the tires. After that, the entire structure must be painted in yellow and plant flowers.

Flowerbed-pool for aquatic plants

Water lilies can also be an excellent decoration for a summer cottage. However, what to do if it is not possible to equip at least small pond or pool? In such cases, it is enough to make a “water” flower bed from the tire. To do this, it is necessary to cut off the upper part of the tire and dig it into the ground to half. Then it is necessary to lay on top a round piece of a special waterproofing film, which is intended for arranging swimming pools, with a diameter of 1 m more than the diameter of the tire. The edges of the film protruding above the side of the tire must be wrapped outward, secured and overlaid with small round stones or broken brick. It remains to put a small mesh basket with earth on the bottom of the reservoir, in which the roots of the water lily are planted.

To make flower beds, you will need:

• chalk or marker to mark the drawing;
• a sharp knife with a thick blade;
• electric jigsaw;
• extension;
• a set of files;
• any, including used, machine oil.

Preparation for work

With the help of worn tires, you can make original flower bed at no extra cost

First, take a close look side surface tires. Special attention pay attention to what is written in small print. You need to look for the word "steel" or make sure it's not there.

The presence of this word indicates that the tire is reinforced with steel wire, so you will need a fine-toothed metal file.

If there is no inscription, the tire is reinforced with nylon, and to work with it, it is necessary to insert a coarse-toothed file for soft wood into the jigsaw. A large-toothed file is easier to cut rubber, because you have to make less effort.

Often steel wire used for tire reinforcement trucks, but you still need to check the tire so as not to dull the file.

If you have not only a tire, but also a disk for it, you can make two types of flower beds - low and high.

The cutting technology is the same, the difference is in some marking nuances and the way the tire is “turned inside out”. Moreover, it is necessary to determine which particular flower bed you will make before marking.

markup

When marking, try to draw even, symmetrical lines and do not make the wide part of the petals of the flower bed narrower than 7 centimeters. Smaller petals are much more difficult to cut because the stiffness of the rubber is not enough for normal pressure jigsaw and saw.

Regardless of whether you want to make a low flower bed, low or high, the markup must be divided into three stages:

• marking a small (inner) circle;
• marking a large (outer circle);
• marking of teeth (petals).

A small circle is marked 3-5 cm from the edge rim, if it is not there, then 5–7 cm from the bead ring (a place to install the disk). This is necessary to avoid damage to the file on the disc and to remove thin and overly flexible sections of the tire.

To draw an even circle, hold the chalk large and index finger, press your little finger against the disk (if you are marking a tire without a disk, then grab the bead ring of the wheel with your little finger) and draw a chalk or marker along the wheel. This will allow you to use the disc or ring as a guide, so you can draw a neat and even inner circle.

We mark the tire like this

If the size of the petals is less than 7 cm, then the large circle is marked as described above. For higher petals, it is necessary to mark as above, but with the little finger to hold on to the top of the tire, or use a tape measure to mark the perimeter of the outer circle. The distance between the marks is 5–15 cm. After the marks have been made, draw a circle over them.

Petals can be marked both by eye and with a tape measure. The shape of the petals is only limited by your imagination. It can be triangles, waves, sine waves, oblique teeth, squares, slots, or anything else you can think of.

tire cutting

Before you start cutting, think again about what kind of flower bed you want to see. After you cut the tire, make changes to the design and appearance flower beds will not work.

Using a sharp knife, cut through the side of the wheel along any line. Then insert the necessary file into the jigsaw and lubricate it engine oil. Connect the jigsaw through the extension cord to the outlet, then insert the saw into the slot in the tire. Turn on the jigsaw and start cutting the wheel.

When cutting tires, follow safety rules

Please note that cutting a tire is a difficult and lengthy business, requiring compliance with safety rules:

1. Try not to hold the tire on the cutting line near the jigsaw with your hand. If the file breaks or pops out of the slot, you will injure your hand. While cutting, push the jigsaw forward strongly, but smoothly, without sharp jerks.
2. If you have enough strength, then instead of a jigsaw, you can cut tires with a sharp knife with a thick (at least 4 mm) blade. But this cutting method is not applicable for steel-reinforced tires.
3. Start each cut only after lowering the knife into the tire to a depth of 2-3 cm and cut only by moving the knife down. This will help you avoid cuts and more serious injuries.

tire eversion

After cutting through both sides of the wheel, it is necessary to unscrew the tire. This operation requires quite a lot of strength and skill, so the first time it may not work.

If it didn’t work out, don’t despair, after a while try again or ask someone stronger to turn it inside out.

It is better to ask someone strong enough to turn the tire out

When turning the tire, do not be afraid to damage it. Tire even from passenger car designed for such loads that cannot be created by hand.

As a result, we should get something like this:

Inverted tire - already almost finished flower bed

We grow, plant and care for stonecrop.

Flowerbed painting

If you have an airbrush (spray gun), then it is advisable to paint the inside-out tire before installation. After all, with the help of a spray gun you not only paint a new flower bed, but also hook on the adjacent soil.

If you only have brushes, then it makes no difference whether you paint before or after installation.

For painting, use nitro enamels or alkyd paints.

Wipe the surface of the inside-out tire with a dry, clean cloth to remove dust and remaining rubber chips. Then degrease with white spirit, 646 thinner or acetone. When the liquid dries, paint with a brush or spray gun.

If desired, the flower beds can not only be covered with paint of the same color, but also draw pictures or drawings.

The appearance of the flower bed can be anything, it all depends on your imagination and on the design of the site.

See the photo in the gallery for ideas for decorating a flower bed from a tire:

One of the most simple ways ennoble a suburban area - arrange it with flower arrangements. Colorful flowerbeds, mixborders and blooming rabatkas transform the territory, making it elegant and cozy at the same time. To highlight the natural beauty flowering compositions, they need to be framed in a decent frame, which can be flower beds made of tires. Do-it-yourself flowerpots will serve not only as a functional design element, but will give the site exclusivity.

Wanting to decorate the site, supplementing it with picturesque multi-level containers, it is not at all necessary to spend a lot of money on the purchase of ready-made flowerpots in gardening stores. You can make beautiful and durable flowerpots from outdated car tires. The main advantage of this material is its resistance to adverse weather conditions and the ability to maintain an attractive appearance for several seasons.

Decorative flowerbeds from old tires allow not only to emphasize the splendor of the colors of flowering plants, but to complete the compositions

To make a flower bed from tires with your own hands, you can use tires of both imported and domestic production. But if there is a choice, preference should still be given to imported products, since they are made of softer rubber, which is much easier to work with. When choosing between summer and winter tires, it is better to prefer the second option.

Since in the manufacture of such a flowerpot the most difficult question is how to turn out the tire for the flower bed, because the rubber is quite a hard material, to facilitate work, it is better to choose tires with maximum tread wear.

Tires with a diameter of R12-R17 are suitable for arranging flower beds. Products required size You can always get hold of any tire shop.

Using tires different sizes you can make original multi-level flower beds that will become a spectacular decoration of the front area or a recreation area on suburban area

How to make a flower bed from a tire: from simple to complex

The easiest option for arranging a floor flowerpot from a car tire is to create a flower garden from a tire, in which the side rubber surface was cut off and filled soil mixture.

It will take no more than half an hour to make such a flowerpot. It is easy to decorate the outer sides of the flowerpot by painting the surface oil paint various shades

But to do original flowerpot on a leg, fringed, or designed in the form big flower, it takes a little more effort.

A do-it-yourself flowerbed of tires can look like a flowerpot with smooth edges or a bowl with a wavy cut line, or even an outlandish flower framed by curly petals

Before you make a flower bed out of the wheel, you need to thoroughly clean the base. Contaminated car wheels are cleaned of sand and dirt. This procedure is necessary in order to facilitate the work in the future: the blade of a file or knife becomes dull much faster when cutting edges on dirty material.

Drawing a contour line and making cuts

Having decided on the shape of the future flowerbed of tires, it is necessary to apply a contour on the side of the prepared tire using chalk or a marker, along which the cut line will subsequently be drawn.

When planning to arrange a flowerpot in the shape of a flower, the contour of the petals should be applied in such a way that the size of each of them does not exceed 12-15 cm.

If you make petals bigger size, then after the tire is turned inside out, the flower bed may not accept the desired round shape, but will have angular joints of slices.

To make cuts, you need to prepare a well-sharpened shoe knife. You can increase the slip of the knife blade during the cutting process by lubricating its surface with liquid soap. The use of a jigsaw will greatly facilitate the cutting process, with which it is convenient to perform any curly sawing.

All cuts are made on soft rubber, the boundary of which is a metal cord located under the tread inside the tire

tire eversion

For arrangement decorative flower bed on a stable leg, it is necessary to turn the prepared tire with cut edges inside out. The process of turning a wheel is one of the most time-consuming stages of work, and for many craftsmen it often becomes a real stumbling block. Knowing a little trick will help you cope with this difficult job: you need to make every effort and turn only a small part of the tire inside out, and then work will go"like clockwork." The tire is turned over with cuts down and laid on a flat surface. The part of the tire where the rim goes into a hard tread is pressed with a foot, and the rubber is turned out at an angle of 45 degrees from the center.

One of the examples that clearly demonstrates the process of turning the wheel.

How to paint a flower bed from a wheel: design options

The vase is almost ready. It remains only to correct the shape of the edges and arrange it in the same style with other elements. landscape design. Until the outer walls of the inverted floor flowerpot are covered with a layer of dust, they must be painted. For these purposes, you can use enamel, oil, or nitro paints. A layer of paint applied to a clean, fat-free surface will last more than one season. Leftovers can also be used to decorate a flowerpot. car paint in aerosol cans, which can be sprayed on the side walls and the leg of the flower bed in just a few minutes.

It is desirable to paint not only outer part flowerpot, but "capture" the upper 10-15 centimeters inner surface.

When making flower bed better to use paint light shades, which will partially reflect the sun's rays, preventing overheating of the soil in the container

Colorful flower beds, painted in contrasting shades and decorated with outlandish patterns, look original.

An unusual addition to the ornament can be glued glass pebbles that look like frozen dew drops. But when decorating flower beds, you should not be too zealous, because the planted climbing and creeping plants will cover most flower bed walls.

Old car tires are a popular replacement for traditional flower beds. It is convenient to place them in small yards without lawns, along roads, in places with high lying groundwater. The flowerpot from the tire is easy to move to any place on the site, if desired, it can be installed on legs. Another popular garden shape is wheels stacked in the form of a pyramid.

To create flower beds, it is better to use products from winter tires they are much easier to cut. Old tires are thoroughly cleaned of gravel and other foreign matter, washed and dried. Then they can be painted in the desired shade, painted with an original pattern. Another popular option is flowerpots in the form of volumetric bowls. To make them, zigzag cuts are made on the top of the tire with a sharp knife or jigsaw. Turning the product is difficult, this will require significant physical strength.

In order for plants to develop well, fertile soil is necessary with large quantity compost. During the planting season, tires are periodically fed. complex fertilizer for flowers. It is important to ensure that the soil does not dry out; planting in a limited capacity should be watered daily.

What flowers can be planted in tires

Most often, annuals are used for planting in flowerbeds from tires. Seeds germinate for several weeks, so it is more convenient to use grown seedlings. When planting, the needs of each particular plant are taken into account. For example, for the normal development of a bush petunia, at least 5 liters of soil are needed, ampelous forms will require up to 7 liters.

Flyers with beautiful shape buds and various colors. Popular are regular and terry petunias, cluster or cascade. It is best to use modern hybrid forms, they form lush compact bushes with a large number of buds.

Nasturtiums look very impressive: orange, red, yellow. Nasturtium does not tolerate transplanting well, so seedlings are planted in tires in peat cups or swollen seeds are sown. In rubber flower beds, you can plant decorative calendula and escholcia, these species form beautiful composition. Another example of successful color combination- silver cineraria and bright red salvia.

Suitable annuals include viola, verbena, marigolds, subulate phloxes, and celosia. Look more interesting tall plants- lupins, cosmea, saffron, fragrant tobacco. As an accompaniment, you can plant ground cover plants, such as alyssum with a delicate honey aroma.

Some gardeners plant perennials in homemade planters. When dividing the bushes, a lot of planting material remains, tires will be an excellent field for experimentation. Small-flowered chrysanthemums can be planted in tires, different types carnations, primroses, daisies, daylilies, ornamental onions. beautiful flowering plants worth adding fragrant herbs with elegant leaves - thyme, oregano, lemon balm, mint. They not only look beautiful, but also repel pests.

You can make a lot of things out of old car tires. original crafts to decorate the garden. The advantage of their use is the low cost of materials, ease of manufacture, durability. To revive the suburban area with your own hands, you can make a snail from a tire.

For the manufacture of a snail, it is better to use an old worn tire with an erased tread pattern and without a solid steel mesh. It will be easier to cut crafts from it, and the result of labor will turn out prettier.

The tire should be cut with a sharp knife or electric jigsaw. If for the manufacture of crafts is chosen big tire, then it is better to use the grinder. To make cutting easier, the rubber should be moistened with soapy water all the time.

Making a snail from a tire is quite simple, since you will have to cut quite a bit.

First, the tire must be cut across in one place to get a continuous strip of material. Next, you need to draw the head and horns of the future snail on the tire and carefully cut them out.

Before coating with paint, the workpiece should be washed and degreased with gasoline or other solvent.

With nitro paint or water emulsion, you need to paint the details of the snail from the tire with your own hands. The dried workpiece must be rolled up in the shape of a shell, fastened with brackets or screws. If the neck of the snail does not hold, you can fix it with non-metal rods.

Eyes, mouth and other small details are best drawn after installing the product. lower part blanks for this should be sprinkled with soil, or a small pedestal should be made for the snail from the tire and the resulting craft should be fixed on it.