The ceiling is painted with oil paint what to do. Ceiling painted with oil paint

The technology of preparing the ceiling for painting is not unique and includes standard painting work. However, there are a few professional tricks and tricks that will be mentioned below.

The steps in preparing the ceiling for painting are the same for any room in the house, only the materials for the work may differ. So, for example, in a humid room it is better to use a moisture-resistant putty, instead of a simple one. But about everything in order.

Stages of preparing the ceiling for painting

Let's divide the work on preparing the ceiling for painting into the following stages:

• Ceiling cleaning;
• Ceiling plaster (if necessary);
• Puttying the ceiling, you need a number of times;
• Grinding the ceiling between puttying;
• Finishing putty of the ceiling;
• Primer before painting.

Cover the floor before starting work. If the floor will not change, its shelter must be approached especially carefully. Put cardboard on the floor, cover the cardboard with two layers of thick polyethylene of 100-200 microns. Put the top layer of polyethylene on the wall and stick it to the wall with paper masking tape. The concrete floor may not be covered.

Ceiling cleaning

As always, the first step is to clean the surface of the old finish, bumps to the concrete base.

Wallpaper

If the ceiling is finished with wallpaper, and the wallpaper is poorly removed, they need to be wetted with warm water. Use a foam roller for this, it absorbs water well.

Whitewash

Cleaning whitewash is dirty, but not dusty, so even a concrete floor is best covered with polyethylene. You can cover not the entire floor, but the place of work, and then drag a piece of polyethylene around the room.

Whitewashing from the ceiling is removed as follows. Liberally wet the part of the ceiling that you can reach. You will have to work from a ladder or table. Wet whitewash is easily scraped off with a metal spatula. In such a wet way, remove all whitewash. After removing the whitewash, the ceiling must be washed twice with warm water. It is better to add laundry soap to the first water. After washing, you will get a clean concrete surface ready to work.

class="eliadunit">

Ceiling painted with oil paint

If the ceiling was previously painted with enamel or oil paint, it is better to remove it with the same metal spatula. If the paint cannot be removed, cover the entire ceiling with a primer like Betonkontakt. It will cover any paint and create a solid foundation for further work.

water paints

If you need to carry out a complex of works on preparing the ceiling (leveling, puttying) on ​​a ceiling covered with water-based paints, then the water-dispersion paint must be removed, and the well-adhering water-based paint can be left.

Concrete ceiling in a new building

The concrete ceiling in a new building is usually covered with mortar drops, concrete, sand and similar construction results. They need to be knocked down, cleaned with a spatula and rinsed with a ceiling.

Ceiling plaster

If full or partial plastering of the ceiling is required, it is primed with Betonokontakt. After the concrete contact has dried (14-20 hours), the ceiling is plastered with gypsum plaster. For example, Rotband.

Ceiling plastering and sanding

Before any layer of putty, the surface of the ceiling is primed. On concrete and plaster, a deep penetration primer is used. For loose surfaces, a latex primer is used to create a durable surface layer.

• Rusts, cracks are sealed with a molar mesh (sickle). For the best quality, the entire surface of the ceiling is puttied on a paint grid.

The ceiling is puttied 2-3 times. After drying of each layer of putty, the surface is polished with sandpaper. The sandpaper is fixed in a special holder. The fidelity of paper (the degree of surface roughness) decreases from layer to layer. The last layer is sanded with sandpaper called “zero”, this is the most “smooth” sandpaper. Sandpaper is bought on a cloth basis, it is more convenient to use and does not require frequent changes.

To get the perfect painting option, you can make a finishing putty. For finishing putty, ready-made polymer putty with a coating layer of up to 0.5 mm is used.

• Before painting, the ceiling must be primed with a special ready-made composition, which is called "Primer".

It would seem that a simple matter is to paint the ceiling

It's been a few months now that I've been renovating. Alone without any help, and without any special training. Before that, I did a little repair work, not professionally, mostly finishing work. Before I started painting the ceiling, I did not read a single line on the Internet on this topic. Apparently in vain. Some things I could do better. It would seem that such a simple matter - to paint the ceiling. In truth, I was hoping to complete this process in a few hours. As a result, everything about everything took several days (about 24 hours in total), because I did not know the most elementary things and reached everything myself. Knowing the simple points, I could do it much faster.

Because Since my ceiling required quite serious repairs, I did not start right away with painting. In fact, the painting process itself is just the easiest thing in painting the ceiling :). In my case, the scope of work, from beginning to end, amounted to: cutting the strobe (for wiring), laying and fixing the cable, sealing the strobe, leveling the ceiling, priming, painting and tinting. Each of these types of work brought me many "pleasant" surprises. In our case, we will assume that you have hidden wiring and you do not need to cut strobes and lay cables, this is a separate topic for a “conversation”.

Tools you will need

Let's start with the tools. So we will need roller. I painted with a long pile roller. The seller recommended it to me (I think not in vain), later I found confirmation of this. Foam and velor rollers are not suitable. We also need paint tray and brush. It doesn't matter which brush, the main thing is more :).

Let me dwell on the paint in a little more detail. I used water-based paint, you can of course oil, but then it will be difficult to tear it off the ceiling in the future. I would also NOT recommend using glossy paint, it perfectly conveys any irregularities in the ceiling and looks somehow too glamorous. You will also need a rag and, oddly enough, construction glasses:). Guess what for? That's all. We turn to the actual painting process, or rather the preparation for painting.

Ceiling leveling

Now even a small child knows that in order to paint the ceiling, it must first be leveled. Most often, the problem of an uneven ceiling occurs at the joints of ceiling slabs. They either stick out or vice versa have gaps. For example, my ceiling joints protruded. I solved it with a grinder. I walked along the joints, removed a layer of paint, concrete and old putty, the grinder removes all this perfectly. When processing joints, the main thing is not to get carried away and not remove too much.

If gaps appear in the plates, they can be eliminated with putty. The difference in height in the slabs can also be leveled with putty. It allows leveling with a layer up to 1 cm, for a ceiling this is quite enough. Important point! When leveling the ceiling, do not use oil putty, it is expensive and cracks on large surfaces, proven by bitter experience. It is good to use oil putty to eliminate small gaps and depressions, no more than 1 cm wide. For example, I puttyed the strobes well with it. If desired, you can putty her the same joints in the slabs.

Prime the ceiling, it's important!

Before leveling the ceiling, prime it and remove the top coat of paint. I screwed up on this. In places where leveling was not needed, the old paint peeled off and went lumpy mixed with the new one, I literally had to pick out the old layers of paint with my fingers. The solution in this case could be this. We take a spatula or sandpaper and scrape off the old layer of paint, quickly and efficiently. As a last resort, when painting, just take more paint so that the roller does not stick to the surface. If your ceiling is painted with oil paint, I would recommend walking on the surface with sandpaper, IMHO it is more effective and the paint will lie better.

We smoothly move on to the painting process itself. When the surface is leveled and primed, you can start painting. There are no tricks here. Most importantly, make sure that the primer and putty are completely dry. According to the instructions, the primer should dry for 1 hour, and the putty for 12 hours (time varies depending on the manufacturer). I waited a day in both cases, it's a lot. In your case, it all depends on your patience. One more moment. You can not apply a primer on top of the putty, the paint will lie perfectly. Especially if it is white paint, it will match the putty.

Some points and tricks worth paying attention to

1. You can use a table as a stepladder, the main thing is that it is stable. The painting process can be easily carried away and played in the box. If the table wobbles, put some paper on it.
2. Wear construction goggles. Believe me, even water-based paint brings a very unpleasant sensation on the surface of the eye. There was an experience, it is checked up.
3. Paint the ceiling first. If you paint or lay the floor first, paint splatters will leave unpleasant memories on the floor surface. Ideally, the order of finishing the room should be as follows: ceiling, walls, floor, everything else.
4. Stir the paint in the jar without opening the jar. Just need to push harder. If you are a woman, ask a nearby or standing man to do this for you. Or, without lifting the can, roll it across the floor.
5. Use a brush to tint irregularities, as well as those places where the roller “does not reach”.
6. While touching up, arm yourself with a rag to immediately wash off the paint if it unexpectedly drips onto the floor or walls.
7. Paint the ceiling in two layers, so you will hide spots and bumps. The third time you can paint, only the most problematic areas. Do not dilute the paint - this is a "divorce".
8. After painting, do not forget to dip the roller and brushes in water so that they do not harden. For example, after the second painting, I lost the roller.
9. Before leveling and painting, remove all lighting fixtures, insulate the wires, or better, turn off the electricity altogether.
10. Clothing should be old, which is not a pity, preferably with long sleeves and a collar.

P.S. If you are concerned about your safety - installing video surveillance, Moscow offers various options. You will not only install, but will also service the equipment. It should also be noted quite reasonable prices for real quality!

Your question:

How to paint walls and ceilings with oil paint?

Master's response:

The undoubted advantage of oil paint is that it is durable and easy to clean.

This type of paint is suitable for painting plastered walls, wooden and even metal parts of objects. However, it must be borne in mind that after drying, oil paints darken somewhat. Knowing this feature, they select a color a couple of tones lighter than desired.

We paint the walls with oil paint.

As with any paint, you also need to carefully prepare the walls for oil paint. If there is adhesive paint on the walls, it must be scraped off, all cracks cleared and cracks that have appeared puttied. After that, the surface must be smoothed with pumice stone and abundantly soaked with drying oil. When the drying oil dries, the walls are puttied 2-3 times. The surface is again smoothed with pumice and only after that they begin to cover with oil paint.

The old layer of oil paint is quite difficult to remove. But this must be done only if the walls will be covered with water-based or adhesive paint. When using oil paint as a coating, only cracked places should be cleaned on the wall and the cracks formed should be puttied.

To remove old oil paint, special chemical compounds are used. In places of a cracked coating, the paint is scraped off with a spatula, the cracks are sealed with a primer and puttied. Painting should start from these freshly puttied places.

If a color similar to the previous one is used, the walls can be painted once. If the color scheme is different, the coloring is carried out twice. A primer layer should be applied under each coat of paint.

If wood surfaces are to be painted, the old paint is carefully scraped off. Clear and putty cracks and cracks.

Not everyone likes the sheen of oil paint. To reduce it, you can carry out trimming, that is, a special brush called trimming is carried out on a freshly painted surface, from which the surface will become rough and the gloss will become less.

In some cases, a combination color is used. This is when the lower part of the wall is painted with oil paint, and the upper part is glued. On the border between two different types of paint, a strip 1.5 cm wide is drawn with glue paint.

Currently, there are many options for decorating the ceiling, but among all the variety, painting remains the most common and economical type of finishing work. However, the process of applying the coloring mixture requires certain phased preparatory work, even if you just need to update the old paint. Therefore, getting started, you should figure out how to properly paint the ceiling on the old paint.

Peculiarities

The need to update the appearance of a painted ceiling arises quite often. This is the least time and effort consuming process. Many property owners choose it precisely because of these advantages, but they also face the question of how to re-paint so that the surface is painted as evenly as possible and does not leave streaks on it.

This type of finishing work is easy to do with your own hands, the main thing is to know some of the features of such work.

• If the old coating layer is in good condition, does not have chips, cracks, does not peel off, does not peel off, just faded and lost its attractiveness, then painting can be done over the old coating. This process will not require large expenditures of money and time, since preparatory work is not needed. It is also not necessary to putty the surface before painting it.
• In the case when the ceiling has already been covered with paint, and at the same time the surface has small fragments of peeling of the material, do not despair, the layer of water-dispersion paint does not require complete removal. In such a situation, it is enough to clean the exfoliated places and apply the coloring composition over the old coating.
• In the presence of severe defects in the finish, additional work cannot be avoided. Cracks, bumps and wrinkles can not be repaired by paint products; such flaws require the consumption of additional building materials.

The old layer of paint should be completely removed. This can be done with a spatula, carefully cleaning the entire surface. With the help of a brush and a special tool, the ceiling must be primed. After the primer layer has dried, the surface must be well puttied, correcting all irregularities and defects. A special base for water-based paint should be applied to the dried surface, this layer is the previous painting.

Paint selection

Currently, for painting ceilings, compositions are used, presented in a huge assortment by manufacturers of paints and varnishes. Each type has its own characteristics, has a number of advantages and disadvantages.

Do not use oil paint to paint the surface of the ceiling. The best option is water-based paints, water-based, or, as they are also called, water-dispersion.

• no pungent odor;
• absolute non-toxicity;
• good adhesion with most building materials;
• the possibility of applying to old paint;
• practicality in use.

The most popular types of water dispersion paints are:

• Latex- has a good level of coverage and density, after drying it is not washed off, the surface can be subjected to wet cleaning. In most cases, one layer is sufficient.
• silicate- A good option for exterior decoration of buildings. This type of paint is more expensive than its counterparts, since it is based on liquid glass. As a rule, this coating is used for profile finishing of various surfaces, in warehouses and industrial premises. Perfectly covers the surface of concrete or stone.

• Acrylic the most versatile paint, adapted to various surfaces. This substance is able to hide minor surface imperfections, and textured paint can remove minor cracks or potholes. Acrylic coating dries quickly enough and does not change color during operation. Has a certain level of resistance to direct sunlight. Of the shortcomings - sensitivity to moisture. The color palette of acrylic paints is huge. All shades can be glossy or matte. The matte surface can visually increase the height of the ceiling, help hide some defects. Gloss is convenient for use when painting planes of large areas, it requires a perfectly flat surface.
• Silicone paint creates a beautiful finish that can be washed. This type of paint is suitable for coating surfaces in rooms with high humidity and sudden changes in temperature.

Each type of paint, if necessary, can be diluted with water to give the desired consistency. With the help of tinting pigments, you can get any desired shade, just add the desired amount of dye to the white composition.

How to calculate the expense?

Before buying, it is necessary not only to decide on the type and color of ceiling paint, but also to calculate the required volume, which is due to its consumption. The required amount depends on the size of the room, which determines the area of ​​\u200b\u200bthe ceiling. Usually, all the necessary information for calculating the coloring composition is on the package, so be sure to read the manual.

In general figures, you can navigate the following calculations. The average consumption of water-dispersion paint when finishing ceilings is about 100 - 120 g / m2. Depending on the surface, at least two or three coats will need to be applied for a good uniform finish. The consumption of material is approximately the same, that when using a roller, that - brushes. If we take into account the lack of experience and the inability to grind the paint professionally, then the average consumption will be 300 g / m2.

In any case, these figures are approximate, the consumption depends on many parameters, so it is better to take paint with a margin.

Having chosen the necessary type of water-based paint, on the package you can read information about whether it requires dilution. If manufacturers recommend diluting the purchased material, then water can be added to the right amount of paint, as a rule, no more than 5-10% is required. The prepared volume is best used immediately, do not let it thicken again. The best option is considered to be diluting the paint to the state of liquid cream.

It happens that the material does not require dilution, it is enough to mix it thoroughly. Such manipulations are enough if it is planned to paint the ceiling in one layer; in such situations, the paint should be a little thicker.

For the entire surface of the ceiling, you should purchase paint from the same manufacturer, of the same brand. This requirement is a guarantor of a uniform monochromatic coating.

If you plan to paint the ceiling not in pure white, then it is better to entrust the tinting to specialists, they will help you choose the right shade and mix the components thoroughly.

How to apply?

Painting the ceiling with old paint is not difficult; even an inexperienced person can do it with their own hands. After all the stages of preparation, you need to start painting.

The best is considered to be a paint coating consisting of three layers, in this case you can be sure that there will be no streaks or stripes on the surface. Before applying each layer, the roller must be carefully rolled out in a tray in order to get rid of the excess amount of the coloring composition, thanks to such manipulations, the possibility of smudges is excluded. The first and last layers should be correctly applied perpendicular to the windows, this applies to all types of paint, including acrylic.

When painting, one should not make sudden movements, it is necessary to smoothly drive a brush or roller along the ceiling, slowly, inspecting so that there are no unpainted areas left.

The next layer should be applied only on a dried surface, and it is not necessary to speed up the process in any way, the paint should dry naturally.

After applying the second layer of paint, it is desirable to exclude the possibility of direct ultraviolet rays, as well as the occurrence of drafts, which will help to avoid peeling of the coloring material from the base.

You can paint the ceiling with several types of tools. The most common are a paint brush and a foam roller; you can also apply paint using an airbrush, which is a conventional spray gun. This device helps to carry out the painting process much faster, the main thing is that the consistency of the paint is appropriate.

When repainting the ceiling, it is better to use the same color or a similar shade, otherwise you will have to apply a large number of layers in order to completely paint over the previous coating and achieve the desired result.

When starting to repair your home, whether it is a city apartment or a house in the countryside, everyone understands that the most difficult stage in this case will be finishing the ceiling. Modern companies specializing in apartment renovation offer a wide variety of options for this: ceiling tiles or wallpaper, stretch or suspended ceilings, etc. But not every householder can afford their services. Therefore, do-it-yourself is still relevant.

Until recently, such a type of ceiling decoration as was especially popular. But with the development of new repair technologies, this method is resorted to less and less. This is due to the fact that, despite its cheapness and the harmonious combination of a snow-white ceiling with any type of interior, many are not satisfied with the laboriousness of preparatory work. In addition, the whitewashed surface quickly becomes dirty and loses its attractive appearance.

Today, painting the ceiling with water-based paint continues to be one of the most popular ways to finish it. Unlike whitewash, the surface painted with it retains its aesthetic appearance for a longer time. In addition, it allows for quick and easy maintenance of the ceiling surface.

This is one of the cheapest repair options. In its composition, this paint is a suspension based on polymer particles and pigment substances dissolved in water. Its peculiarity lies in the fact that after application to the surface, intensive evaporation of water occurs, and the polymers form a coating with high resistance to moisture. Water-based paint is an environmentally friendly material that does not cause allergic reactions and negative effects on the human body.

The choice of water-based paint for the ceiling

If you decide that the best option for you is to paint the ceiling with your own hands using water-based paint, then you have a difficult task: to choose from a huge assortment of goods that would suit you in terms of price and quality. Today on the consumer market you can find emulsion paints with various additives:

1. acrylic,
2. acrylic with the addition of latex,
3. based on polyvinyl acetate,
4. with silicone or silicate base,
5. with mineral content.

The cheapest of them - polyvinyl acetate. But they can only be used in dry rooms. Ceilings painted with such paint cannot be washed.

Paints with the addition of latex- the most expensive. They have a number of advantages, such as the possibility of wet care using detergents, obtaining a smooth, beautiful surface, etc.

Acrylic water-based paints- the most sought after. They can be used in almost any room, they have increased resistance to abrasion during washing.

Silicate paints(liquid glass) are widely used for painting plastered, stone or concrete surfaces.

How to choose a water-based paint so that it has high strength characteristics, gives a beautiful surface after painting, etc. By the names of the paint offered for sale in jars, it is difficult to understand how one type differs from another, and what are their advantages. Moreover, the seller himself often tries to sell, first of all, the product that is more expensive, without thinking too much about its quality.

Read the label

Therefore, in order not to make a mistake with the choice, you should carefully read what is written in the annotation on the label of a can of water-based paint. In it, the manufacturer states:

• What type of work is it intended for?
• What is the consumption of paint per square meter (which is very important for determining the required amount),
• The degree of coverage (the ability of paint to cover a dark background with white, in the form of a continuous canvas),
• Its resistance to abrasion during wet cleaning, etc.

Be sure to pay attention to what is written in small print. Most often, the basic information about the technical characteristics of the paint is contained there. For example, if the annotation says that the paint has:

1. "High resistance to dry abrasion"- this means that the surface painted with such paint cannot be washed, but can only be wiped with a dry cloth or a vacuum cleaner can be used.
2. "Use in dry rooms with reduced operational load". This inscription indicates that the water-based emulsion is not suitable for painting kitchens, with a large amount of greasy fumes from cooked food, as well as in bathrooms where there is high humidity.
3. "High abrasion resistance, indelible"- the ceiling painted with such paint can be washed with water without the use of detergents.
4. "Stain-repellent, high abrasion resistance with intensive washing". This is the best type of water-based paint. Surfaces coated with this type of paint may be washed using gentle detergents.

Water-based paints can be glossy and semi-gloss, matte and semi-gloss. Their difference lies in the fact that matte paints slightly mask small surface defects and visually increase the height of the room. But they are difficult to wash. The surface covered with glossy paint is easier to clean, it is more resistant to abrasion, but small cracks and other flaws in the ceiling are noticeable on it. The best option is to choose a semi-gloss or semi-gloss paint.

Another important point. It is necessary to purchase water-based paint in a store that has an insulated warehouse. The fact is that when freezing, the structure of the paint is disturbed, which is no longer restored when it is thawed. And this means that the acquired paint has lost all its useful properties.

It is recommended to use water-based paint, the purpose of which is to paint the ceiling. It is perfectly distributed over the surface, practically does not drip, and has excellent adhesion.

Preparing the ceiling for painting

Before proceeding with painting the ceiling surface with water-based paint, it is necessary to carry out preparatory work. To begin with, it must be freed from whitewashing or layers of old paint. To get rid of chalk or lime whitewash, you will need to moisten it with plenty of water using a paint roller, and then scrape it off using a chisel or steel spatula. Finally, wash the ceiling with a sponge.

Removing the old layer of paint

To update the ceiling, painted with water-based paint, it will take much more time to carry out the preparatory work. This is due to the fact that the process of removing the previous painting is quite laborious, since the layers of old paint practically do not dissolve in water, and therefore it is not possible to scrape them off the ceiling completely. Most often, this work comes down to removing areas of peeling paint with a spatula.

To facilitate this not entirely pleasant work, you can use the following technique: moisten the old coating with plenty of water using a water spray or foam roller. Repeat this procedure twice with an interval of twenty minutes. The moisture should soak the old coating well. Then you need to create a draft by opening all doors and windows. A layer swollen with water forms blisters, and it will not be difficult to remove the old water-based paint with a spatula.

This work must be done very quickly so that the surface to be treated does not have time to dry. After that, it is necessary to treat stains from smudges and rust with a 5% solution of copper sulfate. If there are stubborn stains on the ceiling, use one of the following compounds:

1. a solution of hydrochloric acid, two or three percent concentration (carefully, trying to prevent the acid from getting on the skin, wipe the stains);
2. a solution of 20 parts of crushed lime, diluted with one part of drying oil,
3. a thick solution of water and lime with the addition of denatured alcohol (about 50 ml).

Any of the last two mixtures is applied for 10-15 minutes on pollution. Repeat until they are completely removed. Usually two treatments are enough.

If whitewashing was applied to your ceiling before the current repair - (there you will also find information on how to find out what the ceiling was painted with earlier).

Ceiling leveling

As soon as the ceiling surface is completely cleaned, it is necessary to level it. A thin-layer putty is best suited for this, which has good adhesion properties, has excellent ductility and gives a smooth surface that can be easily sanded with fine-grained sandpaper. Apply putty to the ceiling using a spatula.

Often, the ceiling is leveled by applying a special whitewash putty on an oil-adhesive basis, which is evenly distributed over the surface with a roller, brush or spatula. Before this, it is necessary to repair all cracks and crevices in the ceiling, filling them with the prepared composition. In order for the putty to completely fill the gaps, they must be slightly expanded before applying it.

Primer

The next preparatory operation is the priming of the surface, which is performed with the same paint. It is applied in a thin layer. She is allowed to dry well so that the putty does not come off.

The main stage of painting

Painting tools

To perform high-quality painting of the ceiling with paint based on an aqueous emulsion, you will need:

1. paint brush for painting butt joints between the wall and ceiling, as well as corners;
2. narrow brush for correction;
3. fur, long pile roller,
4. paint bath,
5. ribbed surface for uniform distribution of paint over the surface of the roller.

Staining rules

just as with whitewashing with chalk, it is better to apply the first layer of paint parallel to the rays of light from the window, and the second - parallel to the window frame

Many do not know how to paint the ceiling with water-based paint correctly. In most cases, they do not take into account during the execution of painting work, the direction of the light flux and many other nuances. Therefore, the painted surface is uneven, with stripes from the passage of a brush or roller, with lighter or darker spots. To prevent this from happening to you, follow the following rules.

• It is always necessary to start painting from the corners and joints between the wall and the ceiling. In this case, the farthest corner relative to the front door is painted first. To do this, a wide paint brush is wetted halfway in the paint, then squeezed lightly to remove the excess. A passage is made along the entire perimeter, with a width of 3 to 5 cm. Due to this, with further painting with a roller, the junction of the ceiling and the walls, as well as the corners, will not be damaged.
• The main whitewashing of the ceiling with water-based paint is carried out with a roller. It is applied in three passes, no matter what type of paint is selected. In this case, the very first pass of paint is carried out parallel to the rays of light falling from the window. The second in a perpendicular direction to it. The latter - should always be directed towards the window.
• Each subsequent staining is carried out only on a well-dried previous layer. This takes 8 to 12 hours.

Coloring technology

1. In a bath filled with paint, moisten the roller, and run three or four times over a rough surface. This will allow the paint to spread evenly over the roller.
2. Make the first pass on the ceiling section. Starting from the corner on the left side of the wall opposite the window.
3. Move the roller from left to right. Then change direction. In this case, it is necessary to ensure that the paint lays down in an even layer, without visible transitions. You can move the roller and W-shaped movements.
4. The following technique will help to remove excess applied paint: when there is no more paint left on the roller, pass it over the painted surface. He will absorb all the surplus.
5. In the process of performing painting work, use a directed bright beam of light to check the quality of the painting.
6. The use of a new roller during the last painting will allow a uniform surface to be obtained.
7. Until the paint is completely dry, drafts are not allowed in the room. It is advisable to protect the painted surface from direct sunlight. This will help prevent stains. Do not try to dry the painted surface with electrical appliances.

Features of painting a plastered surface

The ceiling, on which the plaster is applied, can be painted using a special spray gun or a conventional vacuum cleaner. They give a high-quality, uniform distribution of paint on the plastered ceiling surface. At the same time, it lays down in a thin, even layer. It is best to paint with an airbrush on a primer already made with a roller or brush.