What is the installation of uute in the receipt. Thermal energy metering unit
Production
State Unitary Enterprise "TEK SPb" unites 277 boiler houses, 220 central heating stations and over 4700 km of heating networks. The company serves most areas of St. Petersburg and is one of the largest manufacturers and suppliers of thermal energy in the North-West of Russia.
TEK SPb supplies consumers with heat, process steam, and hot water. The scope of the company's activities includes installation, adjustment and repair of power facilities, power, heat and power equipment and power plants of consumers; development, manufacture and installation of equipment for newly constructed municipal heat power facilities, participation in the decision technical issues perspective heat supply St. Petersburg.
The strategic goal of SUE "TEK SPb" in terms of production is the modernization and innovative development of the company's technological facilities to improve their efficiency and energy saving.
- Boiler houses
Boiler houses
On the balance of SUE "TEK SPb" there are 277 boiler houses located in most districts of St. Petersburg. These are large - regional and quarterly heat sources (70 objects), as well as small - group boiler houses (208 objects). Operational management of the facilities is carried out by the Energy Sources Branch.
Among the boiler companies are the largest in Russia in terms of installed capacity. "Peak" boiler house "Parnassus" provides heat and hot water about 2000 buildings of the Vyborgsky and Kalininsky districts of St. Petersburg. Her total thermal power- 1250 Gcal/h.
Boiler houses of "TEK St. Petersburg" have become pioneers in the field of integrated control automation. Constant work is underway to increase the capacity and upgrade the equipment of boiler houses - to meet the needs of developing areas for heat and hot water.
- Heating network
Heating network
The system of thermal networks of SUE "TEK SPb" is the longest in the North-West of Russia and has over 4,700 km of pipelines. The diameter of the largest line is 1400 mm, the thinnest pipe is only 50 mm in diameter. Most of of heating networks was built using the method of underground channelless laying with thermal insulation from armored concrete.
Operational management of the system of heat networks of large boiler houses of the State Unitary Enterprise "TEK SPb" with all the equipment located on them (CTP, ITP, PNS) is carried out by the Branch of Heat Networks. The services of the branch carry out maintenance, operation and repair of the company's heating system, as well as control the parameters of the quality of thermal energy.
- Projects
Priority projects
In 2018, State Unitary Enterprise "TEK SPb" plans to invest almost 9 billion rubles in the development of heat and power infrastructure. This is almost 5 billion rubles from the company's own funds and 3.7 billion rubles from the budget of St. Petersburg, allocated as part of the city's targeted investment program. We are talking about both investments in the construction of facilities, and design and survey activities.
In 2018, funds will be invested in the reconstruction of 28 facilities, with Special attention the enterprise will devote to the heat-grid economy.
- perspective
perspective
Modernization of the thermal grid complex
One of the central tasks of the company in the near future is the complete replacement of obsolete heating mains using the latest technologies and materials. Due to the high level of underrepair in the 90s of the twentieth century, about 20% of the heating networks in the service area of SUE "TEK SPb" need to be replaced or close to this state. Since the beginning of the 2000s, the volumes of modernization of heat networks began to increase. In 2010, a record 210 km of heating mains were installed for the first time. In 2011 - 234 km. According to specialists' estimates, maintaining the volumes of heating networks rerouting at the level of 200-230 km per year will allow minimizing the number of technological failures of pipelines by an order of magnitude within 5-7 years.
- energy efficiency
energy efficiency
Energy Efficiency Priorities
The program for energy saving and energy efficiency improvement of SUE "TEK SPb" has been implemented by the enterprise for more than 10 years. It combines the main technological and innovative solutions, which are approved by the Technical Council of the enterprise and are included in all major working projects for the modernization of facilities.
The program is aimed at improving the efficiency of energy sources while reducing costs, at increasing the volume of energy consumption accounting, assessing the efficiency of energy use and the quality of equipment operation, minimizing energy losses and identifying unreasonably energy-intensive equipment with its subsequent modernization, updating, or - where possible - abandoning it. .
- thermal imaging
thermal imaging
Television aerial photography
Traditionally twice a year - at the beginning and end heating season- State Unitary Enterprise "TEK SPb" conducts thermal aerial photography of the enterprise's pipelines. For each seasonal session, the Mi-8 helicopter makes an average of 20 to 30 sorties, during which it inspects heating networks in the parts of the city serviced by SUE "TEK SPb".
Meaning
Thermal imaging aerial photography is one of the most effective methods non-destructive monitoring of the state of thermal networks. Covering for relatively short span long distances, thermal imaging survey allows you to save not only time, but also financial resources for ground work to identify defect-prone areas. For State Unitary Enterprise "TEK SPb", as a company with the longest system of heating mains in the North-West, this is especially significant.
- Heat supply scheme
Heat supply scheme
St. Petersburg heat supply scheme for the period up to 2030
In 2014, by order of the State Unitary Enterprise "TEK SPb", the St. Petersburg Heat Supply Scheme for the period up to 2030 was developed, which is the main document that defines the key principles for the development of the city's heat and power industry for the next 15 years. Requirements for the composition and content of the Scheme are determined by the Government Russian Federation, and the result of the work is presented to the residents of the city on public hearings and approved by the Department of Energy.
The heat supply scheme of St. Petersburg determined the strategy for the technological and organizational development of the heat supply system of the entire city, the necessary volumes of modernization and reconstruction of heat sources and heat networks, the investment needs of the industry, as well as mechanisms for attracting and returning them while maintaining the policy of curbing tariffs for the population.
Every month receipts for payment of consumed services are received. They are awarded to a citizen living in a given residential area. They indicate how much we pay for gas, electricity, water, etc. New samples differ in a set of abbreviations, color (for example, in St. Petersburg - a pink payment, in other regions - yellow), etc. An example of a receipt will be given below. In case of accrual of illegal amounts, which means if two receipts have arrived, with a double size, etc., then it is necessary to complain to the authorized bodies.
Who generates utility bills
In answering this question, several aspects must be taken into account. Thus, according to the law apartment building utility bills are sent and formed by managing organizations. They are authorized to calculate the consumption of the following housing and communal services:
- for water supply;
- for an apartment (depending on the number of persons registered there);
- for major repairs, etc.
Separate receipts for citizens come for gas and electricity. This is due to the fact that these organizations are direct providers of utilities, and therefore charge directly.
What does a utility bill look like?
The housing and communal payment looks like in the following way: This is a written document that lists the services for which a fee is charged. There are also rates.
The bill of lading has the following content:
- Payer reference.
- Address and location of the dwelling.
- The name of the service provider and its bank details.
- QR code.
- Information about the services provided.
- Tariffs that are applied in the calculation.
- The total amount due.
Depending on the management company, the receipt may also include services for garbage collection, sewerage, general house needs, heating, etc.
Housing and communal services - what is it and what is the difference
Before you figure out what the difference between these concepts is, you need to understand the decoding of this abbreviation.
Housing and communal services is understood as housing and communal services as a branch of the economy engaged in the study and formation of a range of services necessary for the normal life support of the population.
Housing and communal services are housing and communal services, that is, a specific resource provided to citizens - electricity, hot water, etc.
The concept of housing and communal services is much broader than the concept of housing and communal services, and includes, in addition to the list of services, other significant provisions, legislative norms, standards, etc.
What is included in the rent, utility payments and on the basis of what the amount of the rent in the receipt is formed
Depending on the basis on which the citizen owns housing, the receipt may include various elements. This is the payment for rent, for capital and Maintenance, for housing and communal services, etc.
It is also important to determine the basis on which the total amount payable is formed. First of all, the formation of payments is influenced by contracts concluded by citizens and government organizations (for example, a social contract of employment). Particular attention should be paid to the regulations adopted in the region on the provision of public services. It is also necessary to take into account the tariffs in force in the subject of the Russian Federation. Very important is the reading of meters installed in citizens' apartments.
What is included in utilities when renting an apartment
In this situation, you need to identify what kind of lease takes place. If this is a social rental, then the communal apartment also includes rent for housing.
In situations where there is a civil law tenancy, the rent is addressed directly to the landlord, and the tenant may actually pay it. These conditions must be spelled out in the contract. The possibility of the reverse order of calculation is also allowed.
Legal regulation
In the field of housing and communal services legal regulation includes such legal acts as:
- The Constitution of the Russian Federation.
- housing code.
- Privatization Law.
- Decree of the government in the field of housing and communal services.
- Private contracts.
- Regional legal acts.
It is in these legal documents that the tariffs for utilities, the procedure for their payment, the procedure for repaying debt obligations, etc. are reflected.
As a rule, regulation most often occurs at the regional level, so special attention should be paid to the regulatory legal acts of the constituent entity of the Russian Federation.
Explanation of abbreviations in the receipt
The receipt for utilities includes a lot of abbreviations that need to be deciphered and understood. Each abbreviation is indicated by a set of letters and has its own name. Let's deal with some of them.
SEON
This is a rather specific column in utility bills. SEON stands for Unified Public Information System. As a rule, this includes sending messages to citizens about impending natural disasters, etc.
SOI
This is one of the most common columns in the payment system. It is deciphered by the phrase "maintenance of common house property." It obliges citizens to pay mandatory expenses for needs common property in home. SOI includes:
- maintenance of stairs;
- entrances;
- elevators;
- attic, etc.
The amount of payment for SOI is determined by the agreement between the tenants and the management company.
ROM
This payment is applied only in those houses where an intercom is installed. The abbreviation stands for: intercom system ". In some cases, the ROM fee is issued on a separate receipt.
Citizens are obliged to pay for its maintenance and maintenance of normal technical condition.
ODN
Common house needs are an analogue of SDI. This is also the cost of maintaining common property. There are no differences in these abbreviations, it all depends on what set of letters the managing organization designates these expenses in the payment.
UUTE
UUTE in the receipt is responsible for providing thermal energy to apartments. It reflects how many resources were supplied and at what rates the fee is calculated. The inclusion of UUTE occurs depending on the season.
Abbreviation definition: evils of heat energy accounting.
DSKPT
stands for " additional systems cable program television". This column is not available in payments in all regions. It is a fee for the provision of telecommunication services, maintenance of a common house antenna, etc.
The MTCT can be challenged by a citizen in a situation where he uses cable TV and an antenna.
POAC
In order to understand what POVK means, you need to refer to the norms of housing legislation. This is an additional fee for providing heat to the apartment. A couple more letters are assigned to this abbreviation, for example, TXV.
APPZ
APPZ involves payment by citizens for the development and maintenance of systems that protect the house from sudden ignition. Such systems protect not directly the apartment, but entrances, stairs, attics, etc.
AUR
AUR is also a specific line of expenses in bills. This includes a set of payments aimed at ensuring the work of the administrative and managerial apparatus, for example, a management company.
GTC
The GTC includes the amount and types of costs for the collection, repair and installation of various metering devices, such as water or gas meters.
ELDT
This is the "daily consumption of the electricity meter." As a rule, such consumption is not indicated in all regions. A separate line can also indicate the night consumption of ELDT.
TPP
TPP includes payment for water - "coolant".
VDGO
The decoding of this concept includes the provision and maintenance of gas equipment. VDGO includes both plates and gas boilers, and columns. Citizens are required to pay for the inspection, repair and maintenance of these devices.
PD number
Water disposal in utility bills
Citizens are also required to pay for wastewater disposal. This is charged every month. The management company issues such a receipt, and it also issues an invoice for the withdrawal.
Water supply
A separate column indicates hot water and cold water. This is, in essence, supply of hot and cold water to the apartment. This is done through common pipes.
DHW
DHW refers to the provision of hot water. Filling in the column must occur in accordance with the requirements of the law. For consumption hot water in the situation when there is a column at home, no fee is charged.
cold water
This is the supply of cold water to the apartment. Payment is made according to general appliances accounting (common house) or individual, standing in the apartment. The calculation is formed for a certain period.
Heating
Abbreviations for heating have already been discussed above. It should be noted that the provision of this service is seasonal and, for example, in the summer, payment for heat is not charged.
Example of a utility bill
The form and form of the payment notice (invoice) is a written act that includes the name of the organization, personal account, an indication of the consumer and a description of the housing and communal services (housing and communal services).
Receipt for overhaul
As a rule, a separate receipt for major repairs is not printed. This line of expenses is included in the general receipt. The amount of contributions is determined by regional legislation or by an agreement with a regional operator. As a rule, these are small amounts of money.
Receipt for gas supply
This document is published separately. The law establishes the tariff, after which the consumption rate is determined. It can be calculated on the basis of apartment meters or common house meters installed in the basement.
Tariffs set by the general norm of consumption in the region may also be applied.. In a situation where there is a use gas cylinders, gas supply is not charged.
Norms and meter readings
They are playing huge role in determining the amount of payment. Devices must reliably indicate how much of a resource was consumed. Periodically there is a reconciliation of testimony by authorized officials.
In the situation when the device is faulty, the accounting of consumed resources occurs according to general norms provided for in the region of residence of the citizen.
Mistakes in utility bills - what to do
In this situation, you must contact either management company(in the one that sent you this receipt with an error), or to a resource supplying organization. Usually written written claim requesting a recalculation.
If this does not help, the citizen has the right to complain to Rospotrebnadzor, the prosecutor's office or the court, which will oblige the unscrupulous organization to correct its mistakes.
Payment reduction application
The decrease in payment can occur for various reasons, for example, due to the fact that the family is poor, a disabled citizen lives in the apartment, etc. The application has writing. It can be submitted both directly to the organization that supplies the service, and through Multifunctional Center. The application can be completed by a tenant or representative.
Sample application for recalculation (reduction) of payment for communal payments can . ⇐
Rent Reduction Rules
In this matter, the following points should be taken into account:
- You can reduce the fee for the provision of low-quality services.
- In the absence of the necessary maintenance of metering devices.
- With illegally overpriced.
- In situations where the fee exceeds 20 percent of total income.
Only in these situations can you really count on a reduction in the amount of utility bills. Everything happens exclusively at the written request of the person, since the reduction is exclusively declarative in nature.
Thus, the receipt includes many alphabetic characters and codes: IPU, IND, ZPU, ADS, AZU, ACN, BULA, VIK, ASPZ, AHR, ICU, OID, SOID, GUP, etc. In fact, this is one and the same the same name for different utilities. For example, OID and SOID apply to the common property of MKD, IPU and IND - they mean a fee for metering devices, ZPU and ADS - as well as to metering devices in terms of sealing.
The thermal unit is a set of devices and instruments that account for energy, volume (mass) of the coolant, as well as registration and control of its parameters. The metering unit is structurally a set of modules (elements) connected to the pipeline system.
Purpose
A thermal energy metering unit is organized for the following purposes:
- control rational use coolant and thermal energy.
- Thermal and hydraulic modes heat consumption and heat supply systems.
- Documentation of coolant parameters: pressure, temperature and volume (mass).
- Implementation of mutual financial settlement between the consumer and the organization engaged in the supply of thermal energy.
Main elements
The thermal unit consists of a set of devices and metering devices that provide the performance of both one and several functions at the same time: storage, accumulation, measurement, display of information about the mass (volume), amount of thermal energy, pressure, temperature of the circulating fluid, as well as operating time .
As a rule, a heat meter acts as a metering device, which includes a resistance thermal converter, a heat calculator and a primary flow converter. Additionally, the heat meter can be equipped with filters and pressure sensors (depending on the model of the primary converter). Primary converters with the following measurement options can be used in heat meters: vortex, ultrasonic, electromagnetic and tachometric.
Accounting unit device
The thermal energy metering unit consists of the following main elements:
- Stop valve.
- Heat meter.
- Thermal converter.
- Sump.
- Flow meter.
- Return temperature sensor.
- Optional equipment.
Heat meter
The heat meter is the main element of which the thermal energy unit should consist. It is installed at the heat input to the heating system in close proximity to the boundary of the heat network's balance sheet.
With remote installation from this boundary, in addition to the meter readings, losses are added (to take into account the heat that is released by the surface of the pipelines in the section from the balance separation boundary to the heat meter).
Heat meter functions
An instrument of any type must perform the following tasks:
1. Automatic measurement:
- Duration of work in the error zone.
- Operating time at applied supply voltage.
- Excessive pressure of the fluid circulating in the piping system.
- Water temperatures in pipelines of hot, cold water supply and heat supply systems.
- Coolant flow in pipelines and heat supply.
2. Calculation:
- The amount of heat consumed.
- The volume of coolant flowing through pipelines.
- Thermal power consumption.
- Differences in the temperature of the circulating liquid in the supply and return pipelines (pipeline of cold water supply).
Shut-off valves and sump
Locking devices cut off the heating system of the house from the heating network. At the same time, the mudguard provides protection for the elements of the heat meter and the heating network from dirt that is present in the coolant.
Thermal converter
This device is installed after the sump and shut-off valves in a sleeve filled with oil. Sleeve either through threaded connection fixed on the pipeline, or welded into it.
flow meter
The flow meter installed in the heating unit performs the function of a flow converter. It is recommended to install special gate valves in the measurement section (before and after the flowmeter), which will simplify service and repair work.
Entering the supply pipeline, the coolant is sent to the flow meter, and then goes into the heating system of the house. Then the cooled liquid returns in the opposite direction through the pipeline.
Thermal sensor
This device is mounted on the return pipeline together with shutoff valves and a flow meter. This arrangement allows not only to measure the temperature of the circulating liquid, but also its flow rate at the inlet and outlet.
Flow meters and temperature sensors are connected to heat meters, which allow calculating the consumed heat, storing and archiving data, registering parameters, as well as their visual display.
As a rule, the heat meter is placed in a separate cabinet with free access. In addition, the cabinet can be installed additional elements: Uninterruptible power supply or modem. Additional devices allow you to process and control data that is transmitted by the metering unit remotely.
Basic schemes of heating systems
So, before considering the schemes of thermal nodes, it is necessary to consider what the schemes are heating systems. Among them, the most popular design is top wiring, at which the coolant flows through the main riser and is sent to main pipeline top wiring. In most cases, the main riser is located in the attic, from where it branches into secondary risers and is then distributed over heating elements. It is advisable to use a similar scheme in one-story buildings in order to save free space.
There are also schemes of heating systems with lower wiring. In this case, the heating unit is located in the basement, from where it exits from warm water. It is worth noting that, regardless of the type of scheme, it is also recommended to place an expansion tank in the attic of the building.
Schemes of thermal units
If we talk about schemes of heat points, it should be noted that the following types are the most common:
- Thermal unit - a scheme with a parallel single-stage connection of hot water. This scheme is the most common and simple. In this case, the hot water supply is connected in parallel to the same network as the heating system of the building. The coolant is supplied to the heater from outdoor network, then the cooled liquid in the reverse order flows directly into the heat pipe. The main disadvantage of such a system, in comparison with other types, is high flow network water, which is used to organize hot water supply.
- Scheme heating point with serial two-stage hot water connection. This scheme can be divided into two stages. The first stage is responsible for the return pipeline of the heating system, the second - for the supply pipeline. The main advantage that thermal units connected according to this scheme have is the absence of a special supply of network water, which significantly reduces its consumption. As for the disadvantages, this is the need to install the system automatic regulation to adjust and adjust the heat distribution. This connection is recommended to be used in the case of a relationship maximum flow heat for heating and hot water supply, which is in the range from 0.2 to 1.
- Thermal unit - a scheme with a mixed two-stage connection of a hot water heater. This is the most versatile and flexible connection scheme in settings. It can be used not only for normal temperature graph, but also for elevated. Basic distinctive feature it is worth mentioning the moment that the connection of the heat exchanger to the supply pipeline is carried out not in parallel, but in series. The further principle of the structure is similar to the second scheme of the heat point. Thermal units connected according to the third scheme require additional consumption of network water for the heating element.
The procedure for installing the metering unit
Before installing a heat metering unit, it is important to conduct a survey of the facility and develop project documentation. Specialists who are engaged in the design of heating systems produce all necessary calculations, carry out the selection of instrumentation, equipment and a suitable heat meter.
After the documentation, it is necessary to obtain approval from the organization that supplies thermal energy. This is required current rules thermal energy accounting and design standards.
Only after agreement can you safely install thermal metering units. Installation consists of a tie-in locking devices, modules in pipelines and electrical work. Electrical installation work is completed by connecting sensors, flow meters to the calculator and then starting the calculator to conduct heat energy metering.
After that, thermal energy accounting is carried out, which consists in checking the system performance and programming the calculator, and then the object is handed over to the coordinating parties for commercial accounting, which is performed by a special commission represented by the heat supply company. It is worth noting that such a metering unit should function for some time, which different organizations ranges from 72 hours to 7 days.
To combine several metering nodes into a single dispatching network, you will need to organize remote withdrawal and monitoring of accounting information from heat meters.
Approval for operation
With admission thermal unit before operation, the correspondence of the serial number of the metering device, which is indicated in its passport, and the measurement range of the established parameters of the heat meter to the range of measured readings, as well as the presence of seals and the quality of installation, are checked.
The operation of the heating unit is prohibited in the following situations:
- The presence of tie-ins in pipelines that are not provided for by the project documentation.
- The operation of the meter is outside the accuracy standards.
- The presence of mechanical damage on the device and its elements.
- Breaking the seals on the device.
- Unauthorized intervention in the operation of the heating unit.
We will negotiate with suppliers of materials and equipment to obtain the "best" price.
In accordance with the amendments made by Decree of the Government of the Russian Federation No. 603 dated 06/29/2016, from 07/01/2016 when calculating the payment for utilities supplied to an apartment building or residential building, not equipped with a meter, if any technical feasibility its installationand , the utility consumption standard is applied (without a multiplying factor) and established by Decree of the Government of the Russian Federation dated June 29, 2016 No. 603 multiplying factor , the value of which is in 2016 is taken equal to 1,4 ; from January 1, 2017 - 1,5 . —27.02.2017— THE APPLICATION OF COEFFICIENTS IS CANCELED BY RF GD No. 232 dated February 27, 2017. This rule applies from 01/01/2017. cm.
Federal Law No. 279-FZ dated July 29, 2017 "About amendments to the federal law“On heat supply N 190-FZ ..” and certain legislative acts of the Russian Federation on improving the system of relations in the field ...
In particular, the Federal Law of November 23, 2009 No. No. 261 "On energy saving…” amended obliging owners of facilities with heat load less than 0.2 Gcal/h ensure the installation and commissioning of meters for used heat energy up to January 1, 2019 Features of accounting for thermal energy, coolant, as well as features of fulfilling the obligation to equip facilities with metering devices will establish the Rules for the commercial accounting of thermal energy, coolant, approved Government of the Russian Federation.
|
So why do you need The thermal energy metering unit (hereinafter referred to as UUTE), why it is needed, what gives its use, why it is with us.
UUTE is one of the main components of a set of measures necessary controls consumption of thermal energy, providing not only its accounting, but also the registration and control of the final parameters. It's no secret that our government is recent times spends huge amounts of money to strengthen measures to control the amount of heat consumed by the population, the basis for obtaining analytical data is UUTE.
Installing a meter is not a technology or a method of energy saving, it is an incentive to save energy, so the government thinks!
In the near future, it will no longer be possible to hide the actually consumed energy resources behind regulatory calculations, machinations with house metering devices and shift them to the "shoulders" of the supplier or transporter of energy resources.
To implement this, the state has adopted many regulations. The main one is the Federal Law of November 23, 2009 No. 261-FZ “On Energy Saving and Energy Efficiency”.
So let's get started:
As the government sees the implementation of the Federal Law of November 23, 2009 No. 261 regarding the installation of UUTE.
Installation of UUTE is required. 
The law clearly defines the deadlines for the installation of metering devices for energy resources (hereinafter referred to as energy resources) until July 1, 2012. Owners of premises in apartment buildings, residential buildings, country houses or garden houses with a centralized supply of resources are required to ensure that such houses are equipped with metering devices for the energy resources used, as well as putting the installed metering devices into operation. Wherein apartment buildings within the specified period must be equipped with collective (common house) meters for water, heat energy, electrical energy, as well as individual devices accounting of energy resources (water, gas and electric energy).
Although the deadlines are being pushed back, hiding from the installation behind objective reasons(the roof is leaking, the basement is flooded, etc.) and (or) subjective (the meeting of owners cannot make a single decision) will not succeed for a long time.
Payment for the installation of UUTE.
The law obliges the owners of buildings, structures, structures, residential, country or garden houses, premises in apartment buildings to bear the costs of installing metering devices. If the owner is not able to pay for the UUTE and its installation immediately, the energy supplier is obliged to provide installment payments for up to 5 years.
Comment: Not in all cases, the installation of UUTE is beneficial for the supplier organization, for this reason they are in no hurry with installments.
Is a meeting of the owners of the premises necessary to make a decision on the installation of the UUTE?
Necessary! The collective decision of the owners, adopted by a majority of votes at the general meeting, must be taken on the following issues:
1) the procedure for financing work on the installation of UUTE;
2) determination of a contractor for the installation and commissioning of the UUTE.
Since the future metering unit will become common property, payment for equipment and work is distributed among all apartment owners.
Comment: No protocol for decision does not remove the obligation to install UUTE.
What should the Criminal Code and HOA, ZhSK do?
The task of the Criminal Code or the board of the HOA, ZhSK is to convey information to the owners that the installation of metering devices is necessary in accordance with the requirements of the law on energy saving, and refusal to install threatens with compulsory measures for the installation of metering devices by the energy supply organization and court proceedings. UK or HOA board, housing cooperatives should offer owners options: a list of companies with which it is possible to conclude an agreement for the installation UUTE, their proposals for the cost of work and the quality of the equipment offered, payment options for the work performed, including the cost of the meter itself.
Comment: In most cases, homeowners do not receive reliable information about the lists of companies and the proposed methods of payment and installation of equipment. The reasons for this: low awareness and lack of interest.
Who is the customer under the contract for the installation of UUTE?
As a customer under an agreement on the installation (replacement) and (or) operation of collective metering devices for used energy resources, a person responsible for maintaining the common property of the owners of premises in an apartment building, or a person representing the interests of owners of residential (country, garden) houses, united by common networks of engineering and technical support. (Order of the Ministry of Energy of the Russian Federation dated April 7, 2010 No. 149).
Comment:
The contract is concluded by the UK, HOA, ZHSK i.e. persons responsible for the content.
The procedure for installing UUTE. 
- Conducting an inspection of the object, obtaining specifications from the heat supply organization and project development (contractor).
- The developed project is coordinated with the heat supply organization - the "contractor".
- Installation and commissioning, programming and performance testing - "contractor".
- Acceptance for operation and sealing UUTE - "heat supply organization".
Comment: The contractor must have a license to perform this type of work (otherwise the equipment may be rejected).
Responsibility for refusal to install UUTE.
If before July 1, 2012 the consumer does not install UUTE, then the energy supply organization is obliged from 2013 to take actions to force its installation and recover in court from the consumer all the costs of installing the meter, as well as legal costs. Resource supply organizations do not have the right to refuse to conclude an agreement regulating the conditions of installation, replacement and (or) operation of metering devices for the resources used, the supply of which or the transfer of which they carry out. The price, the procedure for concluding the essential terms of the contract is determined by agreement of the parties. (Order of the Ministry of Energy of 07.04.2010 No. 149).
Comment:
As a rule, power supply organizations do not have specialized services for installing UUTE (lack of permanent orders, no qualified specialists). For this reason, a chain of contractors and subcontractors arises, whose services significantly increase (several times) the cost of performing work. The energy supplying organization has no direct interest in saving Money owners, as participating in energy efficiency measures, it will return from the state its funds spent on a 5-year installment plan at the expense of investment programs 1-2 years after the installation of UUTE.
Who monitors compliance with the obligations for the installation of UUTE? 
Compliance with these obligations is monitored by the Federal antimonopoly service(FAS) and the Federal Service for Environmental, Technological and Nuclear Supervision (Rostekhnadzor) and their territorial offices in the constituent entities of the Russian Federation.
Penalties for refusing to install UUTE.
Failure to comply with legal requirements for the installation of appliances 
accounting (stages of design, reconstruction, overhaul, construction) - a fine on officials from 20 to 30 thousand rubles, per organization - from 500 to 600 thousand roubles. Non-compliance with the requirements for suppliers of energy resources on the proposal to install metering devices to owners of residential buildings, country houses, garden houses and their representatives - a fine for officials from 20 to 30 thousand rubles, for legal entities - from 100 to 150 thousand roubles. Non-compliance with the requirements for equipping a residential building with metering devices by persons responsible for maintenance apartment buildings- penalty for responsible person from 10 to 15 thousand rubles, for legal entities - from 20 to 30 thousand roubles. Failure to comply with the requirements for equipping non-residential buildings, structures, structures with metering devices by persons responsible for their maintenance - a fine on officials from 10 to 15 thousand rubles, for individual entrepreneurs - from 25 to 35 thousand rubles, for legal entities - from 100 to 150 thousand roubles. (Law on Energy Saving (Article 37) of the Code of Administrative Offenses of the Russian Federation).
Who provides services to UUTE and what is included in the service?
The owner of the UUTE is obliged to conclude an agreement for Maintenance UUTE with a service organization (for example, it can be an organization for installing metering devices, an energy supply organization, a management company).
Comment: In most cases, power supply organizations do not have specialized services for installing UUTE (there are no permanent orders, there are no qualified and trained specialists), it is also important to understand that it is advisable to entrust the service to a third party in the event of possible litigation with the power supply organization in the future. Analysts foresee a surge in activity lawsuits in these cases in the near future. The reason lies in the possibility of dishonest service of UUTE by energy supply organizations.
The following services are included in the operation and maintenance of common house metering devices:
- drawing up reports on the consumption of communal resources;
- providing reports to the resource supplying organization;
- monitoring the operation of metering devices to prevent and eliminate malfunctions;
- setting a common house metering device for commercial accounting;
- regular verification of metering devices;
- organization of repair of failed metering devices.
What energy meters can be used? 
Only those metering devices that are included in the state register of measuring instruments and approved for use on the territory of the Russian Federation should be installed. In addition, the rules for the use of electrical, thermal energy, water and gas establish requirements for the accuracy class of the applied metering devices not lower than the established threshold. The accuracy class is the possible error of the meter in the measurement range, expressed as a percentage. How more number denoting the accuracy class, the lower the accuracy of the instrument.
Our possibilities and offers:
During the period 2010-2016
gg. we have been involved in the design and installation of more than 60
UUTE.
This time has not passed for us in vain - we have come to a clear understanding of the needs of our customers / terms of work - price quality - service - guarantees/. After developing a base of projects, calculations and decisions, we needed to strengthen our positions / price of components - service-qualified personnel - guarantees/. To solve this problem, we entered into a partnership agreement with the leader of the Russian Federation for the supply of heat and gas meters CJSC "TD Teplokom"
(http://www.teplocom.spb.ru). With the aim of effective solution energy-saving tasks in the complex, a dealer agreement with the company OOO "Termalkom"
(www.astratek.ru) manufacturer of liquid thermal insulation. All this made it possible to minimize the cost and timing of our work, as well as the price of the materials used.
It is important to understand that the installation of UUTE is carried out by workers of different specialties. The reason for this is the non-typical nature of the work performed at each site (the timing, components and composition of performers change). P understanding the difficulty in making a decision on the installation of UUTE we are ready to discuss with you various projects cooperation, from development to further support of the implemented project.
Having experience not only in the installation of UUTE, but in such areas of energy saving as - thermal insulation, protection industrial equipment and buildings from corrosion and exposure to aggressive environments, landscaping and landscaping - we will carry out for you free consultations, as well as provide services for supporting documentation in regulatory authorities.
For uniform distribution of forces and costs for the installation of UUTE by time, before 
We propose to consider the possibility of concluding a tripartite agreement ( STS - Owner - Heat supply organization.
In our company, the installation of a heat energy metering unit is carried out only according to the project. Our specialists have the necessary qualifications and extensive experience in the installation of heat metering units various manufacturers.
Installation of a heat metering unit is usually carried out as part of the installation of equipment for a heating point.
The heat energy metering unit (UUTE) is necessary for making accurate calculations with the heat supply organization for the consumed thermal energy. When installing UUTE, payment is made according to actual consumption, and not calculated values.
Installation UUTE from the company "Energomontazh" is:
- Installation of a thermal energy metering unit in full accordance with the design solution and terms of reference
- Initial setup
- Preparation of a complete package of documentation
- Ease of future equipment maintenance
- Delivery and commercial registration in heat supply organization and obtaining the Certificate of Admission
- Training of personnel to work with the equipment
Feedback from a client
JSC "ELTEZA"
“Choosing a company, we, first of all, were based on the optimal ratio of price and quality of work performed.
During our cooperation, we have made sure that the technical equipment and the quality of work are at the highest level. high level, all work is carried out in compliance with the rules and safety precautions.
Director of TUKS MOSPROMSTROY LLC D. A. Shavkov
Examples of installation of heat energy metering units
Installation procedure for UUTE
Development and coordination of the project You can order from us or provide us with your agreed project. Purchase and supply of equipment We purchase equipment according to the project specification and deliver them to your facility. We reduce the time at this stage to a minimum due to the availability of components in our own warehouse and our own logistics. Welding and assembly work We carry out tie-in valves and devices in pipelines. We install the grounding system, if necessary. Electric installation work Install electrical panels, we are laying cable lines and connect the devices to the thermal calculator. Installation of UUTE at this stage can be considered completed. Programming and adjustment We set up a heat meter to work at your facility. We adjust the work of sensors. Registration for commercial accounting and receipt of an act of admission to operation We provide a ready UUTE to inspectors and receive an act of admission. Personnel training When the installation of the heat metering unit is completed and the equipment is allowed to operate, we show the basic methods of working with the equipment. Service We offer our services for and UUTE.Equipment for installation of a heat metering unit
The choice of the operation scheme of the metering unit and equipment occurs at the design stage. We have more than 10 years of experience in installing UUTE and we know the features of installing equipment from various manufacturers.
Free consultation on accessories
The main element of the thermal energy metering unit is a heat meter or heat calculator. The most common type of heat meter is electromagnetic.
It simultaneously registers the volume, mass, amount of energy consumed, the temperature of the direct and return pipelines. Data can be displayed on an external display in hourly, daily or monthly intervals.
We have experience in installing thermal energy metering units with thermal calculators from various manufacturers - VIST, SA-93/94, KM-5, MKTS, MAGIKA.
ASWEGA - SA-94/3 Intelpribor MKTS CJSC NPO Teplovizor - VIS.T LLC NPF ECOS - Magica
In addition to the UUTE thermal calculator, it may also include:
- tachometric transducers - measurement of coolant flow,
- pressure sensors - pressure measurement in pipelines,
- temperature converter or set of temperature converters for - measurement of temperature and temperature difference in pipelines,
- GSM / GPRS modem - transfer of readings from the heat meter to your PC,
- printer - printing of reporting sheets directly from the heat meter,
- stop valve.
The cost of installing UUTE
You can see the preliminary price of a heat metering unit on the page.
The initial data for estimating the cost of UUTE are:
- project,
- the results of a visual inspection of the object.