Secrets of installing a toilet. Connecting the bowl and drain tank

During overhaul apartment, we are faced with the need to replace the old toilet with a new one. A professional plumber is often called in to perform this work. However, installing a toilet bowl with your own hands is not such a difficult task as it might seem at first. If you are limited in funds or want to save on the services of workers, then this article is for you. Below we will tell you how to choose the right toilet, prepare the room, assemble and install a new one. plumbing fixture.

Choosing a toilet

Choosing new plumbing, some features of the toilet and bathroom should be considered. Namely:

• Room area;
• The presence or absence of an external water supply pipe, its diameter and distance from the proposed tank;
• The location of the sewer pipe;

• Release angle. Most best option- This is the installation of a toilet with an oblique outlet. You can measure the outlet height from the floor with your own hands, and with a slight mismatch, install an adapter - a drain corrugation.

All toilets have their own design and fastening features. First of all, you need to divide them into suspended and floor. Installation wall mounted toilet It has aesthetic benefits Moreover, it takes much less space. Whereas the floor toilet is more practical, convenient and reliable.

Flush classification

There are two main types of flush - straight and circular.

1. Straight (or horizontal) is more common in simple budget models sanitary equipment. Water from the tank flows down the back wall of the toilet bowl, which does not allow you to remove dirt under the rim. During the collection and discharge of water, such a toilet creates a lot of noise.
2. Circular flush effectively cleans the entire surface of the bowl due to the ring device. However, toilets with this type of flush are significantly more expensive.

Removing an old toilet

Dismantling and installation of the toilet follow each other in the event that you need to replace the old plumbing with a new one. This happens during the overhaul of an apartment or a bathroom.

All actions must be carried out in a strictly defined order:

1. Put on safety goggles and work clothes;
2. Turn off the cold water, and then drain the water from the tank;
3. Disconnect the water pipe and remove the tank;
4. Unscrew the floor-mounted toilet from the floor;
5. To detach the toilet bowl from the sewer pipe, use a sledgehammer or hammer. Gently tap on the cement or adhesive covering the joint. Make sure that the fragments do not fall into the pipe and do not clog the drain;
6. Shaking the toilet, remove the remnants of the sealant and remove it from its place;
7. Now you can clean the bathroom, clearing the place for a new plumbing fixture. Clean up the sewers and water pipes from rust and plaque, and then treat with a lubricant that prevents metal corrosion.

Building a new toilet

Installing a bidet and toilet is not an easy task, but doable. Any floor-standing toilet bowl consists of two main parts - a bowl and a drain tank. Our first task is to connect these two parts into a complete plumbing fixture using screws, nuts and various gaskets.

The assembly of the toilet bowl begins with a drain tank. First you need to mount the drain mechanism, and then the float. Drain mechanism, which is usually attached assembled, is not difficult to install. Insert it into a special hole on the bottom and secure with a plastic nut, on which then put rubber compressor.

Important: Don't forget the rubber pads! All toilet connections are made using them.

The toilet assembly instructions do not end there. Before proceeding with the installation, you need to connect cistern with a bowl. To do this, you will need metal studs. Install the tank on the bowl and secure it tightly by putting a special washer on the stud, a rubber gasket and securing it with a nut. Repeat all this with the second hole.

Toilet installation

Floorstanding toilet installation instructions

Installing a toilet bowl in a private house with your own hands or in an apartment with the help of a professional - all this does not matter. If your choice fell on a floor toilet, then in any case its installation will have to be carried out according to the scheme described below.

• Before installing plumbing, it is necessary to complete all finishing work.
• Installing a toilet bowl on a cement or tiled floor has its own characteristics. The floor must be perfectly flat, otherwise, when tightening the fasteners, the toilet itself or the tile may suffer.
• Insert the dowels into the holes and screw the plumbing fixture to the floor, but not completely.

• If you are mounting the toilet at some distance from the wall, then it's time to start installing the corrugated pipe and finally fixing the toilet, checking its strength and immobility. In this case, the pipes are connected using rubber seals and sealant.
• When the installation of the bowl is over, it's time to connect the water to the drain barrel and check the operation of the entire device. To supply water, use a corrugated metal hose, tow and nuts of the right size.

Do-it-yourself wall-mounted toilet installation

Installing a toilet with an installation is not much different from installing a hidden toilet. In both cases, the most commonly used bowl hanging type, which obliges us to mount not only a drain tank, but also a metal frame into the wall with our own hands.

Important: Make sure your wall is strong. It is better if this parameter is evaluated by a specialist.

Steel fasteners are mounted with dowels to a concrete and reinforced concrete wall (rarely to a brick wall). The installation height of the toilet bowl is determined independently at this stage.

Attach the toilet bowl and install the cistern following the instructions. Connect them with a flexible hose and connect to the water supply and sewerage system.

Remember: The tightness of the joints in this case is ensured in the same way as in the case of a floor-standing toilet.

Video

Do-it-yourself toilet installation with a competent approach and a thorough study of the issue is unlikely to cause you any difficulties. Below you can find video clips that will make the installation process simple and understandable. Happy viewing!

In cases where there is a desire to save on the services of specialists or just learn a new building skill, information on how to properly install a toilet will come in handy.

What you need to install

Before you install the toilet with your own hands, you need to take care of the availability of a number of tools:

• perforator or impact drill;
• drill with a diameter of 8-10 mm (depending on the diameter of the dowel for fixing the toilet bowl);
• tile drill (if installation is done on a tile or ceramic plate);
• wrench;
• set of wrenches;
• a hammer;
• sealant (either in a special tube or together with a sealant gun);
• screwdrivers (flat or Phillips, depending on the design of the toilet);
• transitional cuff made of rubber 123x100 (if you need to connect to a cast-iron socket);
• a set of fasteners for installing a toilet bowl (if it is not included in the kit);
• rags and a container for draining the remaining water from the old toilet.

Before you install a toilet, you need to do some preparatory work. For example, you need to decide what exactly to connect new toilet with a sewer socket. The following options are possible:

• Corrugated cuff. This method is the most economical, but in this case the toilet cannot be attached close to the socket. This matters if the bathroom is small.
• Straight cuff. It firmly and hermetically connects the bowl of the structure with the socket of the sewer system.
• Eccentric cuff. It is convenient if the connection centers of the system and the socket are displaced.

Next, it is advisable to replace the old flexible water supply. The choice of liner is based on how far from the connections on the pipe with cold water before connecting the filling mechanism of the toilet bowl. To this length should be added 15-20 cm.

If necessary, you need to pre-purchase adapters for threads at the junctions of flax or FUM tape.

In the case when under the old toilet bowl is preserved wooden stand, it must be removed. A nail puller or puncher will help with this. It is possible to close the resulting void cement composition, preferably quick solidification, and with a spatula.

Video - Self-installation of the toilet

Do-it-yourself toilet installation

• First you need to turn off the water. Disconnect the flexible hose, flush the toilet.
• Then you need to unfasten the drain tank. You can carefully, or you can use a hammer (in case the old toilet is no longer needed).
• You can quickly remove the toilet bowl with a hammer and a perforator.

Carefully, so that the fragments do not fall into the sewer system, use tools at the place where the toilet bowl is attached to the floor and the junction of the device with the sewer. Then the old bowl must be removed, pouring out the water that remains.

Wood plank removal and floor leveling

• After the old toilet is removed, you need to thoroughly clean the sewer socket from dirt and rust. Install a rubber transitional cuff 123x100 into the socket, pre-coated with sanitary sealant.
• Then plug the hole with a rag so that odors do not interfere with further work.
• Next you need to remove wooden board and fill the resulting void with repair staff.
• Align with a spatula to the level of the floor.

Marking and installation of dowels

• Put the bowl of the new toilet bowl in the planned place. Mark out through the holes in the bowl on the floor so you can see where to drill. The holes in the toilet bowl are located at an angle, in which case you also need to drill at an angle.
• After marking, the toilet can be removed. Next, you need to drill holes in the previously marked places and insert the dowels.

Toilet cistern attachment

• In accordance with the instructions that came with the toilet, you need to install the fittings for the drain tank. There are some peculiarities in this procedure.
• Tighten the drain and fill valve nuts by hand while holding the valve itself, thereby preventing it from turning and damaging the gasket.
• The valves must be installed so that during operation the moving elements do not touch each other and the walls of the tank.
• In case of uncertainty about the quality of the tank walls and gaskets, apply sanitary sealant.

The drain mechanism is available in a collapsible type to facilitate the installation process.

Installing the toilet bowl

• The connecting cuff is attached with a petal part to the adapter cuff 123x100, inserted into the socket pre-treated with sealant. The outlet of the toilet bowl is inserted into the adapter sleeve until it stops.
• It is necessary to turn the cuff so that the toilet bowl takes a flat position, and all the holes of the fasteners coincide.
• The bowl is fixed to the floor surface with screws with plastic washers. In cases where the floor surface is uneven, use spacers made of pieces of plastic to level the toilet before finally tightening it.

Connecting the bowl and drain tank

Before you install the drain tank on the bowl of the structure, you need to put a gasket between them. For reliability and to avoid displacement of the gasket, it is better to glue it to the bowl with sealant in advance.
After attaching the tank to the bowl, tighten the screws evenly. After that, install the tank lid and the drain button. Then fix the flexible eyeliner.

System Function Check

At the end of all work, you need to check - draw water into the tank and make a test drain. The amount of drained water can be adjusted, how to do this is written in the instructions.
Inspect all components for any leaks. If they occur, check the tensile strength and, if necessary, disassemble the assembly, re-treat with sealant, then tighten properly.
If the cause is a defective part, purchase a new part and replace it.

Final stage

Install the toilet seat and fill the gaps between the toilet and the floor surface with sealant.

Doing such work with your own hands is not difficult if you follow the above recommendations and rules. Good luck!

How to install a toilet in a toilet? You can proceed with the direct installation of the structure after dismantling the old tank. Next, follow these steps:

1. You must first remove the wooden board and level the floor. Clean the sewer socket from dirt and install a cuff 123x100 mm into it, covering it in advance with a sanitary sealant. Remove the board and fill the void with repair compound, use a spatula to level the floor.
2. Be sure to make markings in order to determine where to put the toilet and understand where you will need to drill. If the holes in the tank bowl are at an angle, then drill at an angle as well. Insert the dowels in the marked places.
3. Attach the corrugated pipe to the outlet of the device in order to articulate the tank with the sewage outlet pipe. Important: Use only edged rubber sealant, do not use cement to seal drains.
4. Install the sump valve. Hand tighten the valve nuts. Important: the valve must be held in order to prevent it from turning. Install the valves and use sanitary caulk to properly seal the walls of the tank.
5. Prepare the water inlet by screwing flexible hose to the water tap.
6. You should carefully select the required diameter of the fasteners at both ends of the hose. Thus, 1/8” pipe outlets are often used, but 3/4” pipe can also be installed.
7. Next, the toilet bowl is installed. Fasten the connecting collar with the petal part onto the adapter collar 123x100. Insert the bowl outlet as far as it will go. Rotate the cuff so that the bowl is level. Fix the bowl to the floor surface with screws with plastic washers. In order to assemble the toilet bowl, you need to mount a tank on the base or bring a pipeline from a hanging barrel, which is fixed on the wall. Next, you need to check the performance of the device. Important: turn on the feed cold water, wait until the drain tank is full.
8. Attach the seat to special holes using bolts or anchors.

Before mounting the drain tank on the tank bowl, place a special gasket between them, gluing it to the bowl with sealant.

You have to install the toilet, how to do it right. A video tutorial on how to install a toilet bowl with your own hands will help with this. You will see an example of installing a toilet for the first time.

If you do not have the opportunity to connect the toilet yourself, then you can find the installation wizard. Perhaps you should pay attention to the site https://zakaznaremont.ru/ and place an order for the repair or installation of a toilet bowl. The service for the selection of a master will help you find a suitable employee and discuss all the details of the work. But for those who want to install a toilet bowl with their own hands, they can learn from a video tutorial on how to install a toilet bowl with their own hands.

When the toilet is equipped with a sewerage system for leaving water and a socket for a drain barrel. First, unscrew the stopper with dropsy sockets, using an adjustable wrench. Before this, do not forget to turn off the water for this room.

Flexible eyeliner for a cream barrel to be mounted on a straight or angled faucet as you wish. We seal the thread on the tap with fum tape and twist it into a water outlet.

Align the corner faucet so that it looks down and closes the faucet valve. At the next stage, we fasten the flexible eyeliner to the faucet. The design of the eyeliner provides sealing rubber, so we will not use the fum tape. Everything is prepared for connecting the toilet.

Toilet installation

We proceed to install the toilet and we need to measure the width of the toilet. We determine the middle of the room and make the appropriate marks on the floor. On the floor, with a pencil or marker, we draw the appropriate lines to install the toilet.

If necessary, add sewer drain corner elements. sewer elements so that the best and easier to insert between themselves, it is necessary to lubricate the plumbing silicone grease. Carefully lubricate the gum and the outer part of the corner transition and, without additional effort, join the sewer parts.

Now we will install an additional plastic adapter in the sewer. In our case, the adapter is rigid; in its design, you can use corrugated plastic elements. We apply lubricant to the adapter and effortlessly insert this element into the sewer system.

Let's inspect the toilet itself before installation. We turn it upside down and on the supporting part we look at the bumps that may be. If they are, then we need to remove them with a knife. After cleaning the base of the toilet bowl, try it on to the installation site. It is worth paying attention to the fact that we will not immediately mount the toilet bowl drain barrel. At this stage, it is worth docking the toilet pipe with the sewer.

For additional control, check the distance from the walls to the toilet. Align the toilet and outline the base on the floor with a marker or pencil around the entire perimeter. This line on the tile will further help you install the toilet without additional measurements.

Before we remove the toilet, we need to mark the holes for fasteners. tile on the floor, we will drill with a special drill. AT drilled holes we score plastic stoppers that come with the toilet.

On the new one we put the toilet along the marked lines, we join it with the sewer. We install metal screws with a plastic washer into the drilled holes and, using a special key, twist them halfway.

Application of silicone

Next, raise the base of the toilet bowl to a small height, about 1.5 centimeters. This is necessary in order to create a solid gasket over the entire base area using liquid silicone. Gently insert silicone into the resulting gap. When applying silicone, you should not regret it, the layer itself must be large enough so that the gasket under the toilet is wide. In those places where there were toilet stands, silicone was also applied.

When we release the toilet to the floor, part of the silicone is squeezed out. Now we have to remove it and make a beautiful silicone edging. To do this, we need a homemade spatula that can be made from any flexible plastic or siding. After finishing the alignment of the edging, remove excess silicone with a dry cloth.

Without sparing the silicone on the base of the toilet bowl, we get a wide gasket. Now you should wait a few hours until the silicone grabs. Then you can tighten the fixing screws of the toilet to the floor.

Drain barrel installation

To install a drain barrel to the toilet, you must go detailed instructions complete with toilet. To begin with, on the toilet itself where the drain will go, we install a soft gasket.

Next, install the drain barrel and fasten it with screws. When fixing the screws of the drain barrel, you should monitor its horizontalness using a level gauge. We fasten the flexible eyeliner to the fitting located at the bottom of the barrel. Here we will also not use a fum tape, since there is a rubber gasket.

When the drain barrel is connected, open the cold water supply tap and check the toilet bowl for smudges. The final step will be the installation of a water release mechanism and ceramic tiles on the barrels. It remains to install the mount for the toilet seat. After that, our toilet is ready for use.

Greetings, my dear readers.

And the topic of this article: "?".

Replacing the plumbing fixtures in the bathroom at first glance may seem like a simple task. However, to perform these types of work, certain nuances must be taken into account. When installing one of the main elements of the toilet room - the toilet, it is necessary to take into account a number of process features from selection and purchase to correct installation and connections.

Possessing certain knowledge and skills, as well as having required set tools, installation work can be done on their own.

Typically, flooring toilet room formalized ceramic tiles, a modern models toilets in the base have 4 holes through which bolts are attached. Therefore, the installation will require the following set of tools and materials:

• drill
• drill bit with pobedite tip
• a hammer
• wrench suitable for fixing bolts
• marker
• plastic bushings
• connecting corrugation or plastic corners

So, friends, before you proceed directly to the installation of the product - you need to buy it. How to choose a good and high-quality toilet - read.

Which underfloor toilet is better to choose?

Plumbing hardware stores offer a wide selection of different models from many manufacturers.

IT IS IMPORTANT TO KNOW:

Before purchasing, it is necessary to conduct a visual analysis of the product for the presence of chips and cracks, pay attention to the coating of the product. It must be even.

Next, you should check the completeness. The package should contain documentation - installation instructions and a product passport, which state what is included in the toilet bowl. Then check the presence of all elements, including fasteners.

When choosing a toilet bowl, it is also recommended to pay attention to the method of water supply. In the case of connection from below, the liquid intake will pass more quietly. The aesthetic appearance of the room as a whole will not be spoiled by pipes protruding from the side (in the case of a lateral supply).

By the type of connection to the sewer, this plumbing equipment is different, so before going to the store, you should pay attention to where it comes out sewage pipe(from the wall or from the floor), as well as the angle of the pipe. This information will help to avoid additional costs for the purchase of adapters, and the connection will look more aesthetic.

Types of floor toilets

There are two types of toilet bowl: and floor. The most common model is the floor toilet, which has several advantages:

• a wide range of manufacturers
• more familiar model for most people
• availability of budget options
• installation does not require much preparatory work

When choosing an irreplaceable thing for a bathroom, you should pay attention to the type of sanitary bowl.

According to their structure, they can be divided into three types:

• poppet

The main advantage is design feature this type of bowl. One of the walls has a protruding part. This structure allows you to avoid splashing during rinsing, but odor may occur during use.

• Kozyrkovaya

In this model, the structure rear wall done with a twist. This type does not splash during flushing, and also prevents the appearance of bad smell during operation. This type bowls require careful care, with the use of special brushes.

• funnel-shaped

When flushing, there are small splashes, but the shape of such a bowl is the most hygienic and does not require special care. Imported manufacturers most often produce models of this type.

In the plumbing store, toilet bowls with various drain barrels are presented, which differ in design and installation method.

The types of drain barrels include:

• compact

- is the most common model. This view is mounted on a ledge behind the toilet. Between the elements there is a rubber gasket. Installation is carried out using the screws included in the kit. Some companies also produce models with a one-piece construction of a barrel and a toilet bowl.

• separate

This model is perfect for a small bathroom. Allows you to save space, due to the lack of a rear ledge for a drain barrel. In this case, the barrel is mounted on the wall and connected to the toilet using pipes and hoses. This type provides a better flush, since the water pressure has more pressure.

• concealed installation system

the drain barrel is located inside the false - walls. Flushing is carried out using a button that goes out. If necessary, dismantling, together with the button, you can replace the internal components of the tank.

Ways to drain floor-standing toilets can also vary. Among the presented range there are lever and push buttons. The second option includes more modern models. There are types with two buttons. When you press one, half of the water contained in the tank is flushed, two buttons - respectively, the entire volume of liquid. This option allows you to save water consumption and reduce the payment for the supplied resource.

The material used to make

When choosing a sanitary ware, you should pay attention to the material used for its manufacture. Porcelain and faience are widely used. Data ceramic materials differ in the firing method. Thus, faience has a greater porosity, due to which dirt is absorbed and, as a result, the color of the product changes during operation.

Models from of stainless steel are usually applied in in public places and have anti-shock and anti-vandal properties.

The plastic version is lightweight, does not require special care, but is not durable and more fragile than its counterparts.

The most expensive models made of glass and precious metals help to add sophistication and individuality. glass products only available from certain manufacturers. Plumbing equipment made of precious metals is made to order.

Toilets by type of connection to the sewer

One of the important aspects that builds to pay attention to is the type of connection to the sewer system. Equipment can be connected according to the outlet of drains in the design of the toilet bowl:

• horizontally
• vertically
• obliquely

A universal option can be called a horizontal connection. In this case, the branch pipe can be connected both to a pipe coming out from below (from the floor) and from the side (from the wall).

If the sewer pipe is removed from the floor, then you can safely give preference to the second - vertical way. This type allows you to save space in the room.

In the case of a pipe located very close to the wall, but at the same time it comes out of the floor, it is possible to carry out diagonal connection- inclined type of drains.

How to install a floor toilet with your own hands - video

Installation of a floor-standing toilet - step by step instructions

If it was decided to install the floor toilet without the involvement of a specialist, then this task should be taken seriously. All work is carried out in protective gloves, a mask to protect the respiratory organs, glasses to avoid getting a fragment in the eyes. A rag is being prepared to remove unwanted liquid, a bucket.

• Step 1 - dismantling

Work is underway to dismantle the old toilet bowl. First you need to turn off the water supply. Close the tap of the central riser, if there is an individual one for the toilet, then it will be enough to block it. Drain the water from the barrel. For high-quality removal of the toilet bowl, without damaging its integrity, free access is provided from all sides.

The water supply hose is unscrewed, the corrugation is disconnected or plastic corner connecting the toilet to the sewer.

In case of installation on anchor bolts, unscrew the fasteners with a wrench and dismantle the equipment. If the toilet was glued to the base, then you will need a chisel, a hammer, in some cases a puncher.

• Step 2 - preparing the base

The basis for the installation of new equipment is being prepared if it was damaged during the decommissioning. installation work.

• Step 3 - preparing the base

The next step is to install a new plumbing product.After checking the product for integrity, according to the attached instructions, the equipment is assembled. To protect against leaks, it is recommended connecting elements, in places rubber gaskets additionally seal silicone sealant and leave until completely dry.

IT IS IMPORTANT TO KNOW:

If under flooring pipes for a water-heated floor were laid, then, in order to avoid negative consequences, at this stage it is necessary to know for sure that the heating element line does not pass at the drilling site.

We drill holes with a drill. For easier drilling, the place of contact between the drill and the tile is wetted with water. This facilitates the process, eliminates damage to the drill and reduces the load on the drill.

Plastic bushings are inserted into the finished holes and hammered. The toilet is installed.

Further, the product is screwed to the floor with the bolts included in the kit. Using the key, the fastening is tightened. Stability is checked. Fasteners hidden by decorative plugs in the color of the toilet bowl. The gaps between the floor and the toilet are filled with sealant.

Using a flexible plumbing hose to supply water, the toilet is connected to the water supply. Special corrugation or plastic corners of various bends for connecting toilet bowls, equipment and sewerage are connected.

After complete installation, check for leaks. The water supply is opened, the drain barrel is filled and the liquid is drained. If no leaks are found, the toilet is ready for use.

Conclusion

Well, that's all, my dear readers. I hope I was able to answer the question in this article - how to install a floor standing toilet.