How to soften silicone hose. How to repair a rubber gasket at home

Instruction

Small rubber parts that have lost elasticity from time to time, you can "reanimate" with the help of ammonia or kerosene. Roll long and narrow rubber parts into a spiral. Prepare a weak solution of ammonia and immerse the products in it for 25-30 minutes. If you use kerosene, keep the rubber parts in it for at least 1-2 hours. During this time, the rubber will not only become softer, but may also increase in size. After ammonia and kerosene, wash the products in warm water and soap, then rinse in running water and wipe dry.

The door of the old one, which over time is elastic, the masters advise to pour boiling water over. This helps to restore the former properties of the rubber seal and restore the tightness of the door. To fix the effect, wipe the rubber surface with a cloth soaked in silicone. But this is a measure. If possible, try to replace such a part as soon as possible - it will not live long.

Rubber seals on double-glazed windows, so that they last longer, periodically, when washing windows, lubricate with a layer or glycerin, which can be purchased. But manufacturers advise treating them with special ready-made chemical compounds. They can be purchased at the salon of a company engaged in the production and installation of plastic windows, or on the Internet.

Reestablish elasticity rubber possible with the help of special chemicals. Try Novogum Extra - special, restorative elasticity rubber, which can also offset rubber sheets and rollers. Its cost is small - within 200 rubles. Another tool - Rubber Renew - will also help return rubber belts, rollers, belts and other parts to. It should be applied to the surface of the product by moistening a napkin, swab or brush.

Over the years, the body loses its former elasticity, skin and muscles become more flabby. This natural process, after all, the maximum production of collagen reaches a peak at 25 years. After this age, the content of the “main factor of elasticity” in the body begins to gradually decrease. To restore the elasticity of the body will help simple home care procedures.

You will need

• A mixture of herbs of pharmaceutical chamomile, birch leaves, creeping thyme, sweet clover, hernia, milk, honey, oatmeal, body scrub, massage brush

Instruction

You can restore the elasticity of the body with the help of physical activity. Choose the most suitable for you daily complex exercises that you enjoy. It is important to choose feasible loads, because excessive efforts can lead to muscle injuries and refusal to exercise. Choose a set of exercises that will involve all muscle groups. As a result, after a few weeks, your muscles and skin will become more toned and elastic.

Be sure to take after exercise cold and hot shower. Alternating warm and cold water improves the tone of the skin vessels, and the result of good blood circulation will be smooth and elastic skin. In addition to the shower, use a massage with a stiff brush, first you will need to apply a body scrub to the skin. Use this peeling no more than once a week. A scrub and a massage brush will help the skin get rid of keratinized epithelium, as a result, its regeneration processes will be enhanced.

In addition to the shower, baths help restore skin elasticity - rejuvenating, nourishing and with essential oils. Prepare a nourishing bath: in 200 ml of hot milk, add 2 tablespoons of honey and a teaspoon of rose oil, stir and pour the mixture into warm water. Or prepare a rejuvenating herbal decoction bath: take a tablespoon of dry herbs of chamomile, creeping thyme, birch leaves and medicinal sweet clover. Add 2 tablespoons herb herb and brew the mixture with boiling water. After 30 minutes, pour the decoction into the prepared warm bath. Take baths 1-2 times a week, such procedures improve blood circulation and restore skin elasticity.

To restore skin elasticity after a bath, apply a nourishing mask to the skin. To prepare it, grind a glass in a blender oatmeal, mix them with a glass of milk and add 2 tablespoons of honey. Apply the mixture evenly all over the body, rinse off after 10 minutes warm water.

In the process of restoring elasticity, not only external procedures to improve the blood supply to the skin are important, but also rational nutrition. Design your diet so that you consume 100 grams of protein daily, which is building material for the main factors of elasticity - collagen and elastin. Include in your daily intake fresh vegetables and fruits, they contain vitamins and minerals that are necessary for a good tone of your skin.

Rubber is used in many household structures: various hoses, seals, adapters, car parts. Over time, products made from this material fail, dry out, lose elasticity, and become inconvenient to use. You should not immediately buy new elements, you can try to soften the rubber at home.

Remanufactured rubber part using kerosene

Rubber elements under impact external factors lose their original properties, become less elastic, harden. Their further use will not bring the desired effect, seals, for example, will not be able to make the system completely sealed. The purchase of new rubber elements is sometimes difficult due to the lack of products the right sizes or their overpriced.

The following substances allow you to soften rubber:

1. Kerosene. Allows you to make rubber parts soft by affecting the structure of the material. After processing, the rubber element becomes fully elastic. Recovery technology is as follows:

• fill a small container with kerosene (choose the container size depending on the size of the product to be restored);
• place the part in a container with kerosene for 3 hours;
• after the specified time, check the product for softness, if the result is satisfactory: remove the material and rinse with warm running water;
• dry material natural way, without the use of a hair dryer or battery.

1. Alcohol ammonia. The process of restoring old material is as follows:

• dilute the indicated alcohol with water in a ratio of 1: 7;
• place the rubber material in the resulting solution for half an hour;
• after the specified time, remove the part and rinse with warm running water;
• Allow the parts to dry completely before using them.

Please note: you can not keep rubber in a solution of ammonia and water for more than an hour. If the material does not become elastic after 30 minutes, use another recovery method.

1. Medical alcohol followed by the use of glycerin. The technology of "reanimation" of rubber parts:

• fill the container with medical alcohol;
• put in alcohol a part that needs to be restored for several hours;
• after the specified time, check the condition of the product, if it is soft enough, remove the element from the solution and wash it with warm soapy water;
• rub glycerin into the surface of the part using a sponge (cloth);
• remove any remaining glycerine from the surface of the product.

Instead of glycerin, it is allowed to use automobile oil, it is rubbed into the surface of the product, then the part is kept for half an hour before use. During this period, the rubber becomes sufficiently elastic.

1. Castor oil and silicone. Let's make a reservation right away - this method allows you to quickly "reanimate" the old rubber, but the recovery effect will not last long, after a few days the product will become solid. For this method, follow the sequence:

• smear the part with silicone;
• wait 10 minutes;
• after the specified time, the part can be used.

Note: a similar effect is achieved by using castor oil. It is rubbed into the surface of the part, after which it becomes soft and elastic.

Heating is an effective method

There are situations when the rubber element is difficult to remove from structural parts due to its hardening. achieve desired result you can heat the rubber with a stream of hot air using a hair dryer. When exposed high temperature the material will become softer, it can be pulled out of the part.

Too "hardened" element is softened by boiling in salted water. The technology is as follows:

• fill the container with salted water;
• let the liquid boil;
• place the rubber element in boiling water for 10 minutes;
• remove the rubber and quickly use it for its intended purpose.

This method is quite effective, but has a short-term effect. When it cools down, the rubber becomes stiff again.

Conclusion

You can soften the rubber in the above ways. In this case, it is necessary to take into account: a long-term effect after restoration, has a method with kerosene. Rubber, after its application, remains soft and elastic for a long time, because the structure of the material changes. Other methods do not allow to achieve such a result.

In many cases, rubber products are completely irreplaceable. Various seals, belts, hoses and other parts are found in the design of household items and automotive technology. But with prolonged use or hypothermia, they can become hard and unsuitable for further use. How to soften rubber at home? There are substances and methods of exposure that help achieve the desired result.

Kerosene

This substance is able to change the structure of rubber and restore the elasticity of rubber products. The procedure consists in soaking objects until the desired effect is obtained. Large size rubber can be carefully rolled up before being placed in a container of kerosene. After a couple of hours, the softened part must be removed and rinsed thoroughly.

Ammonia

There is another option - to arrange the product bathing in a water-ammonia solution. The rubber should be placed in the prepared composition and kept for about half an hour. Then the washed and dried part can be used for its intended purpose.

Silicone and castor oil

What can soften the rubber at least for a while? Silicone will have a temporary effect on it. Having lubricated the surface of the object with it, it is necessary to give time for absorption, after which the product will be ready for use. A similar treatment can be carried out with the use of castor oil.

The heating

In a situation where it is not possible to put a hose on a rounded part or pipe, immersion of the desired part of the product in boiling water will help. After waiting a little, you need to remove the hose from the water and, without wasting time, install it in the right place. It will be easy enough to do this, because the material will steam out from the high temperature.

Sometimes there is a problem with the removal of rubber elements from some structural parts. In this case, air heating will be effective. A hair dryer is used. Under the influence of a hot jet, the material will expand, as a result of which it will be possible to scroll and pull off the pliable element.

Such simple methods you can soften hardened rubber, thereby increasing the service life of popular products.

In the section on the question Water flows from drain tank into the toilet. The rubber pad has become too hard. What can soften it up? given by the author sucker the best answer is two weeks p .. beat the cat for puddles in the toilet .. .
Turned out the tank was leaking.

Answer from 22 answers[guru]

Hey! Here is a selection of topics with answers to your question: Water flows from the cistern into the toilet. The rubber pad has become too hard. What can soften it up?

Answer from Yoehmet[guru]
Why soften it, buy a new one.

Answer from Prostitute[guru]
hold it in kerosene, but it's better to buy a new one

Answer from V...Spb[guru]
softening will not work, and all kerosene gasolines only dissolve rubber.
You can wind a little solder (or lead) on top for weight, most often this helps.

Answer from Neurologist[guru]
Try putting a couple of heavy bearings on the thing that's blocking the drain hole... They will rust, of course, but the problem will be solved in time ... And so you have to remove the tank and change the whole system

Answer from Valery Myakishev[guru]
Completely replace the fittings, and neighbors can be flooded.

Answer from a lion[guru]
buy a new one, it costs a penny and adjust the valve

Answer from Alex Mishin[guru]
There is absolutely no need to replace all the fittings - just replace the trigger stop valve, colloquially often referred to as "pear".
Depending on the design of the tank, it is either screwed onto a wire hook-shackle, or (in newer tanks) it is pulled onto a plastic tube that serves as a trigger handle - a “pear” for one and for another case you need to buy a different one that you need - look necessary.
The pear not only becomes hard, but also begins to crumble, and sometimes falls from one side - soaking it in gasoline-kerosene will not help. Although it would get wet normally - the rubber is vulcanized and therefore will not completely dissolve, but only swell.
If you send a picture of your tank inside, I'll try to tell you which release valve you need.
Valve price - from 5 rubles.

Answer from Truculentus[guru]
Nothing to soften to the desired state. Replacement required. A penny nonsense, and work for five minutes.

Answer from Polina Roslikova[newbie]
It is necessary to rub the gum with sandpaper at the point of contact with the fittings of the barrel (to remove the upper coarsened layer of the gum).

Answer from Nikolai Khilko[newbie]
Elementary-in boiling water! But it's better to replace it with a new one!

14.03.2013

No matter how sad it is, but every thing has its own lifespan. And tires are no exception. After a certain time, it begins to lose its shape, becomes dry and hard, cracks and crumbles. And quite often in such a situation, when, as soon as possible, you need to replace a damaged part, there is absolutely no time to go to the store for it, or there is simply no way. But, fortunately, it is still possible to urgently solve this problem. Consider in this article several ways to give rubber elements a second wind.

So, the materials you will need: glycerin, ammonia, kerosene and napkins.

Do not be surprised! It turns out that kerosene and ammonia can really help out when trying to resuscitate rubber parts. First you need to prepare a low concentrated solution of ammonia. Then roll up the long and narrow rubber seals in the form of a spiral. And keep them in the solution for about half an hour. If kerosene is at hand, we carry out the same procedure, only the rubber should be in this solution for at least 2 hours. Result - the parts will become noticeably softer and, perhaps, even a little larger than before. After solutions rubber products must be washed in hot water using a soapy composition, then rinse them in clean water and dry.

The masters also found a solution for a short-term renewal of seals on refrigerator doors. In this case, it is recommended to pour boiling water over the rubber. It is said that for some time the sealant regains its lost elasticity and sealing ability. And in order to consolidate the effect obtained, you can treat the rubber surface with a napkin impregnated with a silicone compound. However, we recall once again that the effect will not last long, so it is necessary to replace the obsolete part as soon as possible.

Many of us have long established plastic windows. But not everyone knows that if the seals on double-glazed windows are properly cared for, they will last much longer. So, you just need to lubricate every time you wash windows. rubber elements a layer of ordinary glycerin or silicone. And for best result it is better to use specially designed for this chemical compositions from window manufacturers. As a rule, they should be offered by employees of the company in which you place an order, immediately. Although, however, today it is not at all difficult to find such a solution on the Internet.