Make an artificial fire for the fireplace. How to make artificial fire in the fireplace with your own hands, simple methods

You can diversify your interior in many ways. For example, the creation of original textures and volumetric drawings on. For these purposes, special mixtures are suitable that perfectly imitate different ones. Decorative plaster, when applied correctly, will create an imitation of masonry. This finish is usually used for, but can also be used in the house. It all depends on your capabilities and desires. You can create a stone effect in different ways, we will talk about them below.

But do not apply this paint with spots, but only paint over all the empty stripes that have formed.

Thus, an overflow of different shades is obtained. Next, remove excess paint from the wall, this will help to show the texture. All white seams need to be drawn with darker paint. After that, light paint is applied to the stones in a small amount, for a more distinct highlighting of the texture. Next, you need to draw shadows on the stones with dark paint.

The end result is a wall with masonry, decorative plaster.

Stencils for imitating stone and brickwork

Currently, there are other techniques for simulating masonry from stucco. These are special models and molds made of plastic.

Working with such forms is quite simple. A certain layer of mortar is applied to the wall, and then, until it dries, a plastic mold is applied to it. By creating pressure on the form, it turns out to squeeze out a certain profile of the stones.

There are molds of different sizes on the market, for example, for one stone or for several pieces at once. Of course, with a large shape, getting relief is much easier and faster. And stones in these forms can be large and small.

Layouts are used to create not three-dimensional, but flat relief. These layouts have a rectangular shape of smooth masonry or the shape of uneven stone.

After you have applied the plaster to the wall, attach a mock-up to it and draw along the edge with a knife. Next, close to the borders of the previous masonry, attach a layout, and again draw a knife around the perimeter. And so on until the end of the masonry.

After the entire wall is ready, highlight all the borders with clearer lines. With the help of special tools, removing excess mortar, you can make seams of various sizes and shapes. This procedure is similar to removing tape.

After all the procedures, the plaster dries, processed and painted, as we described above.

This completes the process of forming decorative masonry. We hope that our article will help you create a unique and original interior in your home.

People living in apartment buildings often dream of a real fireplace, but it is impossible to build such a structure in such conditions. In this situation, false fireplaces, shown in the photo, come to the rescue, with which you can create a cozy atmosphere in the room.

For such a design, drywall, wood, metal frame or tile will be required. Thanks to a rich selection of materials, you can build an imitation of a fireplace with your own hands in a certain style.

Features and varieties

Falshkamina is an imitation of a firebox and a portal, which will be an excellent interior decoration. Such a design can be created in various styles with the addition of various decorative elements. Often, false fireplaces are used to hide interior flaws.

In general, stands out three types of imitation fireplaces:

Imitation of a fireplace in the interior

The main advantage of this design is its versatility. If desired, such fireplaces can only be used to simulate fire, which can be seen in the photo. Some designers prefer to focus on the artificiality of the structure.

For decorating the portal are used different materials and objects. Most often, several candles are placed here. To make the design more realistic, it is enough to place a few logs in the fireplace insert.

Fireplace imitation looks great with firewood on a metal grate. In this case, it is recommended to organize an additional yellow-red backlight.

A good everyday option involves using the mantel as a book stand. You can also place figurines, family portraits or a vase of flowers here.

False fireplaces are really appropriate in the New Year's interior. On the portal, you can arrange garlands, hang socks for gifts, as well as arrange multi-colored balls and fir wreaths with candles. Thanks to the use of a ready-made fireplace portal, after the end of the holiday, the structure can be stored in the basement.

Making a fake fireplace with your own hands

The easiest way is to purchase a ready-made portal. Thanks to a rich selection, you will be able to choose the right size. If desired, it will be possible to integrate an electric fireplace into such a design, having previously taken into account the dimensions and ventilation requirements.

Options for imitation fireplaces

Polyurethane construction

Of course, you can make a false polyurethane fireplace with your own hands. This will require a ready-made portal, special glue, putty and any finishing materials.

Installation:

1. First you need to decide on a place. It is best to install an imitation fireplace near the side wall. If you plan to install an electric fireplace or arrange lighting, you must first conduct electrical wiring and install a socket.
2. A frame is made of wooden beams or a profile. You should also build plasterboard walls, which are attached to the portal with special glue. All gaps are filled with finishing putty.
3. The next stage is the installation of an electric fireplace and the finishing of the firebox. If desired, instead of an electric fireplace, you can decorate the back wall with a mirror, and lay out several decorative logs at the bottom.
4. To decorate the portal, paint or gilding is suitable.

Drywall construction

The easiest option involves creating a false fireplace do-it-yourself drywall. Such a design will be appropriate in any room.

First you need to prepare the following materials:

When making a structure with your own hands, it is first necessary sketch a fireplace taking into account dimensions and connection points.

From galvanized profile frame needs to be done. In this case, all elements are connected by self-tapping screws. To make the structure stable, the parts are fixed with transverse jumpers. The bulky structure is additionally attached to the floor and walls.

Next, you need to cut sheets of drywall and fix them to the profile with self-tapping screws. All joints are puttied, and the corners are strengthened with a paint grid. If necessary, the surface of the false fireplace is necessary level with putty.

The finished structure is finished using tiles, artificial stone or stucco. An imitation of a hearth or a candle is installed inside the firebox. This fake fireplace is safe. Accordingly, it can be placed even in the room where children sleep.

Construction from old furniture

If desired, you can build an imitation of a fireplace from an old closet or chest of drawers. This design is different in that it will not make unnecessary costs for materials. In addition to furniture, you need to prepare several sheets of plywood, acrylic paint, various finishing materials, putty, a grinder, a jigsaw and a screwdriver.

Do-it-yourself work:

How to make fake fire

• The easiest option is to make a drawing. You can also put an electronic photo frame with the image of fire.
• It is worth installing several candles in the inside of the fireplace. To enhance the effect, you should fix mirrors on the inner wall of the fireplace.
• Firewood can be placed on the shelf, and an LED strip can be fixed on the sides.
• The most realistic option involves the installation of an electric or biofireplace.

Artificial fireplaces are great fit into any interior. To create such a design, many finishing materials are suitable. In this case, the finished product is completely safe. To create a cozy atmosphere in the room with a fake fireplace, just turn on the backlight or light a few candles.

The device of a fireplace is one of the interesting interior solutions that give the interior of the home interior warmth, comfort and homely appeal. But it is far from always possible to fit a real fireplace into the design. As a rule, this is due to the inability to arrange a chimney, the lack of storage space for firewood and other reasons associated with the use of open fire in the room.

There is nothing difficult to create an imitation of a fireplace without heating in an apartment with your own hands. This will require drywall sheets, exterior materials, imagination for the project and a good mood for work. The fake fireplace is ready and all that is left is to fill it with artificial flames, sit in an armchair and enjoy the play of light and shadow.

The main task of the illusion of live fire in the hearth is to form a spectacular, as realistic as possible sensation of a burning flame. Visualization is the main element of the task, but not the only one. To complete the perception of the picture, not only the visual component is necessary, but also the corresponding crackling and smell of burning panels, as well as the physical sensation of heat flow. To do this, there are modern methods of creating a "cold fire" in a false fireplace.

A bit of history

The first experiments in creating a safe fire and turning household heaters into residential decor elements have been undertaken for a long time. The origins of this direction include an electric fireplace with a heating element and a decorative panel. It was carried out in the form of glowing coals with internal illumination by a conventional incandescent lamp. Similar imitators could be found in the middle of the last century.

Somewhat later, the backlight was given dynamism. Electrical appliances were equipped with strips of foil that rose in the streams of warm air and reflected bizarre reflections on the body of the device, creating the effect of a flickering flame.

The first successful illusion of live fire was the cutting of light fabric, swaying in artificial air jets pumped by a built-in fan. This principle of imitation of open flame tongues formed the basis for the further development of the design direction and still has the right to life.

Cold fire, obtained in this way "in its pure form", has a sufficient level of entertainment, light reflections whimsically and uniquely change their position in space. But the realism of such an imitation is low, since the picture looks like a hand-drawn one. To add volume and “visual vitality”, a built-in system of mirrors and light filters is used, as well as electronic control of the backlight elements.

In addition to electronic-mechanical methods for creating the effect of live fire, digital and LCD technologies, cold steam generators, 3D holograms with a stereo effect and other achievements of the modern development of science and technology are widely used in our time.

There are several ways to light a safe fire in an apartment fireplace. Let's consider them in more detail.

Method one. Protozoa

If there is no desire or opportunity to engage in the manufacture of a complex electronic-mechanical structure, then you can use the simplest solution to the problem: paste a photographic image of burning firewood into the hearth of the fireplace. To give some semblance of realism, it is necessary to install spotlights with filters of various colors.

The most low-cost, but no less effective, will be the use of an old Christmas tree garland. To do this, mini-plafonds are trimmed with reflective foil from the inside. The controller built into the garland will allow you to simulate the dynamics of light transmission, as from living flames. To give the picture a visual stereo volume, you can choose a holographic 3D image of an open fire of a suitable size.

Method two. Theatrical

As the name implies, this method is borrowed from theatrical props. When, according to the plot of the play, it is necessary to make a safe fire on the stage, the decorators use just such a fire.

To make a theatrical fire in the fireplace, you need to stock up on the following items:

• silent fan of medium power;
• halogen lamps;
• color filters of appropriate shades;
• white silk.

The fan housing is dismantled. Its working part is rigidly attached to the bottom of your fireplace in such a way that the injected air flows perpendicular to the base. The wiring is laid in the cable channels and led outside the fireplace.

Below the working plane of the fan, three halogen lamps are mounted: one along the central axis of the fan, two at an angle of 30 degrees to each side. The direction of light on the future focus should be from the bottom up.

As brackets for fixtures, you can use the remains of a bent metal profile for plasterboard. Light filters are attached at a distance of 1-2 cm in front of each lamp. It is additionally recommended to put a blue light filter on the central lamp, this will give the flame more exotic reflections.

The next stage is the imitation of flames. Irregular future flames are cut from white silk and attached to the fan grille in an "artistic mess".

The open flame simulator is ready to go. It remains to adjust the fan power, the angle of the light filters and fill the artificial parts of the hearth with purchased birch charcoal.

Method three. water vapor

All of these devices can be purchased at retail or dismantled from old concert equipment that creates a vapor effect.

Fog generators are installed at the bottom of a sealed container for distilled water. Each generator in its design involves a membrane, which, due to high-frequency vibration, creates a local reduced pressure. Under conditions of low pressure, water evaporates at a temperature close to room temperature.

The fan is rigidly mounted in the zone of active evaporation and drives the formed steam up. LED backlighting, controlled by a decoder and controller, creates a very realistic visual sensation of the play of light and shadow of live flames.

In the lower part of the fireplace hearth, the steam is illuminated more strongly and there is a feeling of the presence of an open flame. At the top, the backlight is less intense and the illusion of smoke is created.

To prevent the formation of excess condensate, a diaphragm is installed in the upper part of the hearth.

Method four. The use of a salt ceiling

Salt electric lamp is a specific electric lamp. The plafond is made of natural crystal - salt. Under such a ceiling, a conventional incandescent lamp is installed. Passing through the edges of the crystal at different angles, the light flux is refracted and outwardly very realistically resembles the play of living flames.

Using shades of various colors, a realistic imitation of live fire is created. And using lamps with different configurations and sizes, a small fire is easily imitated.

This method has its advantages and disadvantages.

The advantages include the simplicity in the manufacture of such an illusion, its realism. In addition, when heated from an incandescent lamp, the salt ceiling saturates the surrounding air with negative ions. This leads to the neutralization of positive ions, which has a positive effect on the health of its owners.

The disadvantages of this method include the very significant price of such devices and their infrequent appearance in free sale.

Method five. TV instead of live fire

Using a flat LCD TV in a fireplace is one of the most technically simple options for solving the problem. But, it should be noted, far from low-cost.

If the choice falls on such a method of “igniting” an artificial flame in a fireplace, then first it makes sense to choose an LCD TV, and only then, based on its size, mount the fireplace casing. The TV screen is installed on a recess of 10-12 cm in the hearth of the fireplace. Its plastic frame is hidden by decorative elements.

Through the USB port built into the TV, a recording found on the Internet is played on the screen. Depending on the mood and environment, you can choose one of several recordings: the play of flames, embers or a bright fire. The selected record with repeated repetition will serve as an imitation of live fire in the hearth.

If you place a system of mirrors and light filters along the internal planes, then the picture will visually acquire volume and look very natural.

Decorative firewood for fireplaces

To give a finished look to the fireplace under a cold fire, it is necessary to “put” firewood and coals. On the windows of specialized stores there is a huge selection of decorative firewood made of plastic or ceramics. Such dummies exactly repeat the texture of dry or partially burnt wood. Imitation, purchased or made with your own hands, will turn the hearth into the center of home warmth and comfort.

In order to obtain greater realism, a backlight with red light filters is installed under the wood-burning display. In more expensive versions of decorative firewood, internal lighting with a non-repeating flicker cycle is provided.

To give the integrity of the picture, small gaps between decorative firewood are recommended to be covered with natural charcoal.

This summer I did a renovation in the room. The idea to make imitation brickwork pounded my brain for 2 years. I didn’t want to cut the post until I finished everything, but the finances died, and I only had to make a table. But, by the way, today we are talking about brickwork, so let's start.

Here's what was "Before"

Here is an example of a redevelopment. Due to my stupidity, I did not take a picture of the whole room in the very original version, and I could not find older pictures.
As a result, on the first day I took out the whole room, peeled off the wallpaper, removed the linoleum from the floor, ceiling tiles.
Next were the floors. I stretched the lags with 80mm self-tapping screws. I put 10mm plywood on top. The seams were sealed with wood putty. The floors stopped creaking. I also changed the wiring, laid HDMI for the TV set and put the cheapest tile behind the battery.

And now we are approaching the bricks. Went the most important stage - markup. For marking, I used a marking cord. It costs 200 rubles, and saved time darkness.
Before the start of the marking, he called the ceiling workers, they filled the profile under the ceilings. danced from him.
according to the markup: The size of the brick is 6.5 by 25. and its seam is 1-1.2mm. It is important to start marking from the ceiling, because in tiled houses the walls are crooked. On a 4.2m wall, the difference came out to be 2-3cm.

In order for the adhesive tape to hold better, I grabbed it with a small amount of solution.
Scotch took 48mm, sort of, and cut it into 5 parts with a utility knife. it took about 4 pieces.
Next comes the magic:
on top of the adhesive tape, I threw gypsum plaster, with a layer of about 7-10 mm, and leveled it.

gave a little to dry, and tore off the adhesive tape

Immediately you need to check whether everything turned out exactly, because then you had to gouge some gaps with a screwdriver and a hammer.

Painting:
Painted with water-based paint. Used black color. It took about half a liter in total (looking ahead, I’ll say that I still have 5 liters of gray paint left).
The first layer was primer. Very quickly absorbed into the wall. Gypsum though. Immediately put the spots (I really wanted to see how it would look)

After the second layer went through all the gaps with white paint. I took a little, so that it would not flow. But even without this, a lot of places climbed where it is not necessary)
It may seem to many that everything is cool and without jambs. But I did, and I know that there are a lot of jambs))

Then I slightly darkened the paint, painted over groups of bricks. Then darkened again and repeated)
Here I will say an important thing: You need to try the color of the paint on something. I had a plywood floor and I scoffed at it. It is important to have some white paint in stock in order to adjust the color if the color is poured. At the very end, he took a brush, dipped the very tips into white paint, and with quick, careless movements went through some of the bricks.

Let's move on to the painting on the wall. ordered a template in the printing industry. I will also say that I was stupid and overpaid. They made me a laser cut, on a 1mm PVC sheet.
It was necessary to stand on a plotter cutting, on a film.

There are no more photos left, but the process was something like this:
I glued a soldier's template to the wall on a ton of molar tape (I made the inscriptions "Linkin park" and "Hybrid theory" on separate pieces. I also painted over it with a water-based emulsion.
Next, the template removed and tinted the fragments with a thin brush for painting. After drying, I also made the inscription "Linkin Park" as a template. I painted the background for the inscription "hybrid theory" with black paint. For smudges, I made the paint thinner (added water).
Splashed - smudges flowed)

Let's move on... Poster. I love Ramstein! Opposite the bed according to the plan is a telly. It is symbolic that the poster has the inscription "Lichtspielhaus" - which means "cinema".
I made the frame myself. Essentially a rectangle, and in the middle of the stiffener. Attached with a stapler.

Separately, I think, it is worth mentioning the wallpaper. Ordered in the salon. Gave unreasonable money. But I did not find other interesting wallpapers. 3 rolls, 2 pieces. As a result, 6. was enough right back to back.
Waited 1.5 months. Because of them, the repair was delayed.

The telly was presented to the DR. I took it from the point of view of rationalism. Initially planned as a second monitor for a PC. As a result, I took Akai - 127cm, for 25k rubles. Suitable for my needs. Satisfied.

Shelves. A friend cut the boards to my size. I sanded them down, painted and varnished them. Well, you don’t need to screw everything into one pedestal of mind.
Of the nuances - strengthened it with corners inside.

I made a clock out of an old record. I have a laser engraver, so I burned the contours with it. What did not burn through was cut out with a burner.
Screw on the clockwork and you're done.

It seems that he showed everything ... Now for the money:
Plywood on the floor - about 4k
Linoleum - 7k
Putty - 2.5k
Tiles - 2k
Wallpaper - 6k
Stretch ceiling - 9k (together with a corridor 1.5 * 3)
Light - 4 spots + chandelier + switches + sockets + dimmer + wires - 9k
Paint, coller, board paint, varnish - 3k
screws (for the floor) - 1k
curtain, muslin (curtain) - 2.5k
Plinth - 1k
Tool (marking cord, rollers, brushes, spatula, whisk
Stencil + designer's work (translated into vector) + poster printing - 4k
HDMI cable 10m - 1.5k
_________________
Total 52.5k

Many people like to look at the fire in the fireplace. The sight of a flame calms, allows you to relax and immerse yourself in your own thoughts. However, it is not always possible to put a real fireplace in your home, it is especially problematic to do this for city dwellers, whose stress level is very high and who, like no one else, need an effective way to relax.

Fortunately, we can build in our apartment, which will adequately replace a real analogue. At the same time, it can contain real fire if biofuel is used, or an imitation of fire in a fireplace, which you can also make yourself. In this article we will talk about how to make an imitation of fire in a fireplace with our own hands, we will analyze the most popular methods.

False fireplace with skillfully filled firebox

Available Options

A decorative false fireplace is created from various materials, you can use cardboard, gypsum, polystyrene, drywall, plywood, chipboard and even brick. In most cases, these materials are combustible, so it is worth remembering the fire safety standards and not placing real fire in the furnaces. If you plan to build it into a firebox that will create a real flame, then the choice of materials for construction should be taken more seriously. For example, build a brick structure, sheathe the furnace with sheets of metal.

We will consider options when it is required to make an imitation of fire, which would be remotely or very similar to a real flame. And the simplest idea that immediately comes to mind is to create a suitable pattern. Anyone can draw a picture, but how this fire will look on canvas depends on the talent of the artist.

A painted hearth inside a fake fireplace

There are many other options to create an artificial fire in the fireplace so that it is more realistic than a painted one, and the most interesting of them are the following:

• using a steam generator is a modern way;
• the use of fabric and a fan is a theatrical solution;
• the use of LCD displays, TVs is a spectacular option;
• original backlighting with a salt lamp is a useful technique;
• lighting with garlands is a simple method;
• - design approach.

If you want to create a quality fire imitation in a fireplace, you can use any of the available options, but remember that each method has its own advantages and disadvantages. To understand which fire for a fireplace is easiest for you to make with your own hands, let's look at all these methods in order.

General description of popular methods

One of the most difficult ways is to create an artificial fire using the generated water vapor, and we will start with this method.

Steam

To create a steam plant inside your raised fireplace, you will need certain parts and electrical skills. You can look for a ready-made solution, but it will be difficult to find it.

To build a steam generator, we need the following components:

• small quiet fan
• DMX controller and DMX decoder - devices that allow you to transfer digital data and balance the operation of all generator systems;
• light-emitting diode lamp (LED);
• fog generators operating on ultrasound;
• pure water;
• matching box, boxing.

Installation scheme for creating an imitation of fire from steam

The principle of operation of the system for a couple is very simple. Fog generators are installed in a suitable box or box. Pure, distilled water is poured into them, which, under the influence of a fan and a generator of ultrasonic vibrations, begins to gradually evaporate. Note that the evaporation of water occurs at room temperature, and the vapor itself is cold. The rising steam from the evaporation of water is illuminated by an LED lamp, and the effect of a real flame in the fireplace is obtained.

To make the fire look more realistic, a diaphragm should be installed over the entire structure. A diaphragm with holes of different diameters will allow you to vary the speed of the air around you, which means creating more realistic flames.

If we consider the ongoing processes more deeply, then we should recall Bernoulli's law, which tells us that the smaller the holes, the higher the speed of air flows.