How to glue wallpaper for one person. The choice of finishing material: features of different types of wallpaper

New wallpaper will refresh the interior of your favorite room, make it elegant, beautiful and cozy. Sticking any kind of wallpaper is a relatively simple job, although there are some small, but very important nuances, knowledge of which will help you make repairs correctly. So, let's figure out how to correctly glue the wallpaper with your own hands.

If you prefer to entrust repairs to professionals, then we will do a quality job!

Foundation preparation

Old wallpaper must be removed. To do this, soften them with water or soapy water using a roller or brushes. Dense canvases can be precut. After that, wait for the wallpaper to swell and remove it with a scraper, spatula and hands.

The previous paint is removed with a sanding pad, scraper, hammer (ax) and spatula, as well as using special chemicals. After carefully removing the previous finish, make sure that there are no flaking fragments on the wall.

If there are still noticeable flaws, depressions or irregularities on the surface, then, depending on the quality of the walls, it is necessary to apply a leveling plaster or starting putty layer, followed by sanding. It is not necessary to process the wall too “jewelleryly” - minor flaws will be hidden by wallpaper.

It is recommended that the base be well primed with a paint roller and brushes just before pasting the wallpaper. Choose the soil according to the type of surface. For the primer, PVA glue is also used (a couple of glasses per 10 liters of water) or wallpaper glue diluted to 25-30%. Wait for the soil to dry.

Check that there are no adhering debris or specks on the surface. In addition, when wallpapering, be sure to de-energize the apartment and avoid any drafts.

Marking the canvases and fitting the pattern

Traditionally, the height of most types of walls does not exceed 3 m. The length of one roll is on average about 10 m (maybe more), which will be enough for 3 strips. Considering the width of the walls and the width of the canvas, plan the number of wallpapers. For example, the length of the wall is 4.0 m, the width of a piece of wallpaper is 0.53 m, which means that by dividing the length of the wall by the width of the canvas, you can fit 7 solid strips on the wall plus 1 canvas with trimming a little more than half of it.

Roll out the rolls on the floor “face up”, after covering the floor with clean newspapers or a cloth. Workplace should be convenient for laying side by side and trying on two canvases.

To begin with, mark the height of the wall on the first canvas, leaving a certain margin of length at the bottom of the piece (5-12 cm). Place the second canvas next to the first piece of wallpaper, carefully align the pattern, not forgetting the “margin of safety” from below. It is clear that if the wallpaper is without a pattern, then the pattern fitting step is skipped.

Wallpaper glue

It is necessary that the glue strictly corresponds to one or another type of wallpaper. You can read about this on the packaging label or check with managers. Following the instructions, dilute the glue in water and mix everything very carefully. Then wait 15 minutes until the mass is infused to the desired consistency, and stir everything again. Try to make the glue so that it is not too thick or, on the contrary, is too liquid - this will negatively affect the quality of the work. The consumption of wallpaper glue is different, but on average 200-300 g is enough for 6-10 rolls.

Wallpapering process

Question: "Where to start pasting wallpaper?" unprincipled, but it is recommended to do this from the side of the window or the far corner, moving deeper into the room so that the shadow does not interfere with the work. It is best to start gluing with solid pieces from ceiling to floor, leaving corners and segments for later. For the first canvas, it is desirable to draw a vertical, even line on the surface using a plumb line (thread + load) or a level, along which the canvases will be leveled.

Turn the first canvas over on the floor, and using brushes or a roller, apply glue in an even layer, without “gaps”, smearing the wallpaper from the center and further to the edges of the fragment. Wait a little while adhesive mixture absorbed - 4-5 minutes for thin-layer wallpaper and up to 7-10 minutes. - for thick panels ( exact time indicated on the label). Try to keep the impregnation time for all canvases the same.

As a rule, if the wallpaper is single-layer paper, then it is enough to coat only the canvases. However, for vinyl or other similar heavy wallpaper, it is recommended to apply a small layer of glue to the wall as well. But in the case of non-woven wallpaper or fiberglass, on the contrary, it is not the cloth that is coated, but only the walls themselves.

After applying the cloth to the wall, it must be carefully smoothed out. To do this, using a special wide roller, a special brush or clean rags, carefully, but without excessive force, smooth out a piece of wallpaper, first from top to bottom, and then from the center to the edges. Make sure all the air comes out. Special attention give the joints - smooth the ends of the canvases harder. For these purposes, a narrow roller or a special plastic spatula is good. If the edges lag behind, they can be gently unscrewed slightly, additionally smeared with glue and again pressed down and smoothed well.

Then, next to the second fragment, lay the third canvas on the floor, trim, measure and cut it, then spread and stick the second fragment, that is, repeat the entire workflow until the end of the section.

Glue any next fragment end-to-end to the previous canvas. This is especially true for vinyl, embossed, cork and other similar wallpapers. But paper sheets can be glued with an overlap of up to 5 mm, just do not forget about aligning the pattern.

While everything dries, use a clerical knife to cut off the excess from the bottom half a centimeter below the level of the baseboards for bending.

Hard to reach places

Doors, switches, sockets, windows, etc. must be pasted over with thin longitudinal strips of wallpaper along the perimeter of the interference in advance. For better tacking, you can cut the strips into several pieces along the length. Windows and doors are easy to cut. But for sockets, attach an ordinary sheet of wallpaper to the wall “dry”, mark the location of the interference there and make a delivery cross-shaped incision at this point. Attach the fragment again, try on and finally make a hole of the required shape.

Angles.

Thoroughly coat the corner before pasting with glue (applies to all types of wallpaper). Next, try not to stick a whole piece here - it can “move away”. Measure the rest of the segment from the edge of the nearest solid piece, plus add 3 cm here, which will go to another corner wall. Such a capture of the corner is very necessary, since it is very difficult to glue the corner exactly butt-to-butt - there will still be distortions and gaps. Glue the next panel of the other wall already close to the corner, that is, overlapping on the first segment. Control the gluing in the corners with a plumb line.
Sometimes, especially for thick wallpapers, the so-called pruning is used in the corners. The technology is the same, only for the first trimming, the launch is already 7-10 cm. at 5-7 cm). Then knife under metallic profile or the ruler needs to be evenly cut through two layers of wallpaper at once, remove the trimmings and glue the ends back.

Ceiling.

If you plan to finish on top, then in any case, the ceiling should be covered with wallpaper in the first place, and only then move on to the walls. It is better to work together, the ceiling pasting technology is similar. On the ceiling, it is recommended to glue the wallpaper perpendicular to the window, while kneading the glue to a greater density so that the canvas holds better. In addition, when finishing the ceiling, it is recommended to mark all the borders of the canvases at the top, along which wallpaper fragments will be aligned (use a cord previously rubbed with chalk).
For the time of sticking the glue - up to 2 days - do not allow any drafts in the room so that the canvases stick to the walls with high quality. We wish you a successful renovation!

If we talk about the most popular wall decoration in our country, then the undoubted leader in this regard will be ordinary wallpaper. Each owner of his own home should know at least the basic nuances of their gluing. In the end, it's not all that difficult. Since even a beginner who will follow the instructions exactly can glue the wallpaper correctly, we will devote this article to this issue.

You should know that you can stick them both overlap and butt. It all depends not so much on your preferences as on the thickness of the material itself: if it is thick, then it should only be placed on the wall end-to-end. By the way, you need to start from the nearest window, since in this case the seams between the stripes will be less noticeable.

Measure the height of the room should be very carefully. Since it is not so easy to glue wallpaper in most domestic apartments with not very straight ceilings, it is better to measure the height before gluing each strip. Never forget that it is necessary to leave a margin, otherwise a gap may remain above or below, which greatly spoils appearance renovated room.

Don't worry about leftover "orphan" pieces: they're great for patching up minor imperfections and for decorating spaces above doors and window openings. Before you glue the wallpaper correctly, you need to soberly assess the forces: it is better for beginners not to buy those varieties that require exactly matching the pattern.

Never use questionable adhesive left over from a previous repair. It must be fresh, and also exactly match the type. finishing material which you are going to use. If the wallpaper is thick, then the adhesive must be applied not only to them, but also to the wall. After applying the composition, the strip of material is bent in half and left for a couple of minutes. Since it is not easy for beginners to glue wallpaper correctly, it is better to practice, because there is a high risk of spoiling a lot of material.

After impregnation, you can start working. The most difficult thing begins, so you need to follow the typical recommendations: take the smeared piece by the top, unfold the fold (as we said, the wallpaper is folded after applying the glue), bend again by about 1/3, and bend the remaining piece so that the front side " looked at the front. Such an "accordion" is carefully picked up and carried to the place of work. Knowing, you can just as well do it with other varieties of them.

To simplify the fitting of the pieces, it is better to draw vertical markings on the wall. This is especially convenient when you are doing repairs in splendid isolation. By the way, it is very difficult to adjust the pattern in the corner areas, so it is better to start with a flat wall.

Having fixed the strip, it is necessary to carry out from the center to its edges with a clean and soft brush, removing air from under the material. After final fit you can carefully trim off any excess.

If you don’t know how to glue non-woven wallpaper correctly, then use the same tips: there are no cardinal differences in the process.

Do-it-yourself wallpapering is a task that anyone can handle House master. Accuracy and compliance technical requirements- two components of success in this are quite simple matter. Aligning the walls requires professional skills and physical strength, but you can stick the wallpaper on the wall yourself. Repairing an apartment will be cheaper if you carefully study the rules for pasting walls and strictly adhere to them.

How to paste wallpaper yourself: the secrets of success

The person who decides to redecorating on their own, many questions arise. Is it possible to stick wallpaper alone? How to choose the right glue? How to stick wallpaper exactly? How to glue wallpaper end to end? How to quickly paste wallpaper? How to glue wide wallpaper? How to glue wallpaper in the corners of a room? These questions can be reduced to one: how to properly glue wallpaper on the walls.

Do-it-yourself wallpapering the walls, as in the photo, will become a reality if you break the task into parts and follow the recommendations.

Preparing walls for pasting

How to glue wallpaper correctly so that the result does not disappoint? Good start- half the battle: before gluing it is necessary carefully: it must be perfectly even, white, cleaned of litter and dust. The main rule is that it is impossible to glue wallpaper on curved walls, and it is better to invite specialists to level it. Plaster is applied to uneven areas.

If there is oil, water-based paint or old wallpaper on the walls, you will have to work hard before gluing new ones.

Is it possible? Many experts advise not to do this. To take off the old paper cover, it is enough to walk with a wet roller or a rag with soapy water. After 10-15 minutes, the paper will easily separate from the walls.

As you can see in the photo, the old coating is not always completely removed. Residues are rewetted and removed with a spatula.

If there is a waterproof film on the surface, it should be cut or scratched with a wire brush before wetting. When the surface swells, it's time to clean it off.

Removal old paint

Is it possible to glue wallpaper on sanded and primed oil paint? Professionals do not advise doing this: there is a high probability of delamination. Oil paint removed mechanically or with special chemicals. The lagging paint is removed with a spatula, and then options are possible.

Removing paint with a hammer and chisel is a laborious and lengthy process, but relatively environmentally friendly. More often, a grinder with metal brushes or a perforator is used to remove old paint. The disadvantage of this method is a large number of dust that will settle for several days. A part is removed along with the paint concrete base- as a result, the surface is littered with irregularities, and it has to be well putty.

To remove only the paint, washes are used. Removal of paint using special chemicals is carried out in two stages: a wash is applied to the surface, and then the softened paint is cleaned off with a spatula.

It should be remembered that paint removers are very toxic, so work is carried out in a well-ventilated area, be sure to use a respirator and gloves.

To hang wallpaper on walls covered with water-based paint or whitewash, it will have to be carefully removed with water and a scraper. Hot water will make the task easier.

Pasting the walls with wallpaper can be started only after the complete removal of the previous finishing materials, correction uneven areas, finishing puttying and grinding. The importance of these steps cannot be underestimated: proper preparation- a guarantee of excellent results.

When the walls are leveled, puttied and sanded, it remains to apply a primer that will protect the coating from moisture, prevent lag and reduce glue consumption. The primer is evenly distributed over the surface with a brush or roller about a day before wallpapering on the wall.

How to choose tools and equipment

How to glue wallpaper correctly, avoiding common mistakes? First you need to prepare the equipment.

For work you will need:

• ladder;
• tray;
• bucket;
• knife-cutter and wallpaper scissors;
• narrow metal spatula;
• wide spatula;
• plastic spatula / wide rubber roller;
• small rubber roller;
• brush / roller for glue;
• roulette;
• pencil;
• level or plumb.

The photo shows the most necessary tools: a special tray allows you to evenly distribute the glue over the roller, a plastic spatula or a wide roller is useful to press the canvas, and a narrow roller is designed for joints.

It is better to apply glue on the desktop. If it is not there, it is done on a film-covered floor.

High-quality wallpapering: what to look for

Before starting work, the question naturally arises: what to glue the wallpaper on? The adhesive composition can be selected independently, depending on the type of coating, or you can contact a sales consultant for help.

Another problem is where to apply the glue: on the wallpaper, on the wall, or on both surfaces? Pay attention to the special symbols highlighted in red in the figure: they will help you navigate.

The basic rules for wallpapering are simple

Windows and doors must be tightly closed. Why is a draft dangerous? The glue will dry too quickly, which will cause the glued sheets to peel off the walls.

A prerequisite for gluing wallpaper is de-energizing the room. It is necessary to turn off the electricity when approaching an outlet or switch: glue, like any liquid, can lead to a short circuit.

Before gluing, you need to cut the required number of strips and mark the top with a pencil on the back. It is convenient to put a mark on the edge, which will be cut off later. This will speed up the bonding process.

If the rolls are plain, the length of the strip is calculated based on the height of the ceiling with an overlap of 5 cm above and below. If there is a pattern, the length of each strip is increased by its step in order to properly join the pattern.

Work should begin by marking the wall: in order for the lines to be even, you should use a level.

It is necessary to ensure that the glue does not get on the outer part of the wallpaper: if they are light, the spots will be noticeable.

But how, so that the glue does not show through at the joints? It should not be applied much, do not be afraid that the joints will lag behind the wall a little: after drying, this deficiency can be corrected by spot application of glue from a special tube.

Beginners are often concerned about the question of how to glue the wallpaper in the corners - internal and external. Wallpapering in the corners is done at the final stage, when the main area of ​​the room is already pasted over. It is especially difficult to glue the corners with wallpaper if there is a window opening nearby: the canvas adjacent to the window is carefully cut.

How to glue wallpaper in the corners of the room?

There are several ways.

Method 1. One glued canvas is wrapped at an angle so that a strip of about a centimeter is obtained on the adjacent wall, as in the diagram.

The second canvas is cut so that the edge fits exactly on the corner. The joints are passed with a narrow roller. If you work in this way, overlaps may be visible.

Method 2. To make even the thickest wallpaper look neat at the corners, both canvases are glued, going onto the adjacent wall by about 2 cm. Then both excess strips are removed with a cutter: for this, a wide spatula rests against the corner, which is gradually shifted until the overlaps are will be cut off completely.

The outer corners of the room are glued in a similar way. To paste over the corner protrusions, one strip is led around the corner by 1-2 cm, and the second is glued exactly along the corner. The glued corner will look neat. If the wallpaper is very dense, resort to using a cutter.

Features of pasting walls with wallpaper of different types

Modern wallpaper production makes it possible to produce products based on paper, textiles, polymer materials. Wallpapering different types has features.

paper wallpaper

How to glue paper wallpaper? It is eco-friendly and easy to operate decorative coating successfully competes with many new finishing materials. But how to glue wallpaper on a paper basis? This will help step by step instructions.

1. The starting line is marked on the wall, stepping back from the corner of 30-40 cm. They put a dot at the top and draw strictly with the help of the level vertical line to the floor.
2. The strip smeared with glue is folded so that the glue is inside (this stage is relevant for those who glue without an assistant). If the adhesive is applied to the wall, it covers a slightly wider surface area than the roll. Under the ceiling and near the floor it is more convenient to use not a roller, but a brush.
3. The glued strip is pressed from above with an overlap on the ceiling of 4-5 cm (this will later allow you to cut the wallpaper in a straight line).
4. The side of the wallpaper is leveled and pressed with a flexible plastic spatula or a wide rubber roller strictly along the starting line.
5. By moving the pressure roller from the center of the strip to the edges, excess air is expelled.
6. With a wide metal spatula and a paper cutter, cut extra part stripes under the ceiling and at the plinth.

A start has been made, it remains to decide whether to glue end-to-end or overlap. Previously, no one asked this question, because paper wallpapers could only be glued with an overlap. Now overlapping wallpaper is rarely glued, and there are rules here. The wallpaper must be thin, and the width of the overlap cannot be more than 15 mm.

Some types of modern paper wallpapers, for example, duplex, cannot be overlapped: because of the thickness of the paper, it looks ugly. But how to glue paper wallpaper end-to-end? According to the described scheme, only the role starting strip each time will perform the newly pasted area. Sticking wallpaper end-to-end directly depends on the quality of the preparation of the walls: if they are even, there will be no problems.

The following video shows how to properly glue the wallpaper back to back.

At the final stage, the slopes can be decorated with plastic corners.

Vinyl wallpapers

Wall covering with vinyl wallpaper has its own characteristics.

It should only be with special glue, having carefully studied the instructions: it will indicate what glue should be applied to.

Glue is applied to the walls thin layer. Before you start pasting the walls with vinyl wallpaper, the glue is allowed to dry for about 20 minutes.

How to glue wide vinyl wallpapers? To mask the joints on them, work starts from the corner closest to the window. lower part the strips are kept rolled up while the top is smoothed out.

Non-woven wallpaper

How ? Interlining is a non-woven fabric that is wear-resistant and difficult to stretch: this feature determines the technology of pasting walls with wallpaper on this basis. When choosing, interlining is also often used.

Do-it-yourself wallpaper should be glued, not forgetting the following nuances:

• the base must be well putty and have a uniform White color: due to the thinness of the coating, the walls may shine through;
• the glue is carefully prepared from the powder according to the instructions and applied only to the wall;
• non-woven coatings do not shrink, so they will not disperse at the joints, but the protruding glue should be immediately removed with a dry cloth, otherwise it will be noticeable after drying.

The non-woven base allows you to produce wallpapers with a width of 90-140 cm. But how to glue wide wallpapers correctly? It should be borne in mind that the walls must be very even: with a large width, even a slight curvature will affect the correctness of the joints.

How to glue wide wallpaper? To keep the canvas from moving, you need an assistant. Glue is applied, as a rule, only on the wall, and the canvases are smoothed from top to bottom. Otherwise, the technology is the same as for narrower canvases. Wallpaper should be glued correctly, avoiding glue getting on the outside. Sticking wide wallpapers is not as difficult as people who are accustomed to standard 53 cm wide rolls fear.

Armed with the knowledge of how to stick wallpaper with your own hands, and having studied many of the intricacies of the wallpapering technique, you can get to work. If the rules were followed at each stage, you can be proud of the result.

This is the first stage on which the success of the whole event depends.

The requirements for the surface are as follows - it must be dry, smooth, without cracks. Of course, the remains of the previous finishing materials are usually preserved on the wall, they should be scraped off. To facilitate the process, the site advises to wet the wall with water and wait for a quarter of an hour, after which the scraping process will become easier. It is necessary to prime the surface before sticking the wallpaper if the walls in the apartment are new.

Freshly plastered walls are ready for gluing if they look light and dry. To check the readiness, you can resort to the following test: stick a piece of plastic film to the wall with adhesive tape, and after 10-12 hours, see if the surface is fogged under the film. If there are no traces of fogging, then this means that the wall has dried out enough and is ready for wallpapering. The porous structure of the plaster perfectly absorbs moisture, so it is worth priming the surface 1-2 times and then pasting it over.

It often happens that the wall on which the wallpaper is to be glued is covered with paint or varnish. Then you need to find out if you need to remove them or you can glue them on top. To check how firmly the varnish or paint adheres to the wall, we use adhesive tape, a strip of which we stick on the wall and then peel off with a sharp movement. If there are particles of paint or varnish on the adhesive tape, then the strength of the fastening of the new finishing material on such a wall cannot be guaranteed. In this case, the paint will have to be removed. Alternative option- wash the walls first with an alkaline solution, and then with water. And plastering is recommended!

To remove glass wallpaper and other types for which dispersion glue was used, you will need a special solvent.

Thus, wall preparation is as follows:

• cleaning from dust and dirt particles with sandpaper, removal of the old coating by the methods described above;
• leveling with putty with simultaneous filling of all cracks, in difficult cases applied reinforced mesh and an additional layer of putty.

Types of wallpaper and features of their gluing

Released today various kinds wallpapers, the gluing technology of which can have serious differences. For some types, it is enough to apply glue only on the design material or on the wall, for others it is recommended to lubricate both the wallpaper and the surface they are shaped with glue, there are other discrepancies.

paper wallpaper

The most popular type, the most affordable. Gluing paper wallpaper is easy. They differ in thickness, surface texture (smooth, embossed or patterned). They can be glued with almost any glue, the main thing is to carefully apply it in an even layer on the wrong side of the wallpaper sheet.

When sticking models with a pattern, you need to control that it is correctly compiled.

There are paper wallpapers that are painted after gluing, they are a white embossed canvas.

Non-woven wallpaper

The material for them is a non-woven material called interlining. It is recommended to glue the material on very well-aligned walls, since it does not mask these surface defects and stains.

As for the gluing process itself, it is simple:

• first we smear an even layer of glue on the wallpaper;
• then put them on the wall.

But it is important to remember that special glue is required for work.

Vinyl wallpapers

It's comparatively the new kind who uses good demand, thanks to such qualities as:

• easy gluing;
• a wide variety of textures;
• resistance to fading and yellowing;
• the presence of a moisture barrier.

The base material is paper or interlining, on which a layer of foamed or smooth polyvinyl chloride is applied. Such wallpapers are also valued for the fact that they mask the unevenness of the walls well.

Wallpaper glue

As a rule, there is an indication on the roll about the type of adhesive recommended and recommendations for use. We advise you to carefully study this information and do not deviate from the recommendations given by the manufacturer. This is especially true of the proportions that must be observed when diluting the powder, otherwise you risk getting poorly glued wallpaper with spots.

When applying the sheet to the wall, it should be lightly pressed down with a soft brush or roller, smoothing from the center to the edges so as to prevent the appearance of bubbles. From an awkward movement, the glue may end up on the front surface, it must be removed with a damp sponge, gently wetting the place stained with glue, but do not rub!

During the drying of the glued walls, it is not worth heating the room unnecessarily, as well as creating drafts, since these circumstances can lead to divergence of the joints,

Professionals do not advise sticking the strip through the corner or into the corner.

In the process of wallpapering, the door is approached from one side. A wallpaper strip that captures some of door leaf must be cut vertically to the upper border of the sash. The strip is pressed against the wall surface vertically, and the protrusion below the upper edge of the door is cut off. The ledge above the door is pressed against the wall.

If there is a radiator on the wall, then it is recommended to glue the wall behind it no more than 10-20 cm, and paint the rest of the place to match the color of the wallpaper.

How to glue wallpaper (video)

We hope that the article helped and it will now be easier for you with the question of how to properly glue ilm non-woven wallpaper with a paper base, and the result will be durable and pleasing to the eye.

Any repair begins with the acquisition of the necessary building materials, with tool preparation and dismantling old finish. The last position is associated with some difficulties, because tearing off, for example, old wallpaper from the walls is not as easy as it might seem at first glance. If they were well glued, then removing them can be a problem. But there are several ways to help you quickly carry out this operation.

Ways to remove wallpaper from walls

Before you start removing wallpaper from the walls, you need to take care of protecting the floor. It's best to put it on polyethylene film, which is attached to the plinth with masking tape. After that, the wallpaper is moistened warm water using a roller and allow time for them to soak.

If there is a question quick removal, it is better to use a special solution that penetrates the adhesive layer in minutes and dissolves it. The material itself begins to flake off, it remains only to collect it and throw it in the trash. It should be noted that solvents are not included in such liquids, therefore, after removing the wallpaper, there is no need to rinse the walls with water. Some areas, even under the influence of a solvent, will not peel off immediately, so it is recommended to re-apply the liquid and use spatulas.

• It is not necessary to wet the wallpaper strongly, the water will begin to flow down the wall, and only a small fraction of it will be absorbed. But a small amount of water will also not give a positive result. They will dry out quickly.
• It is necessary to moisten in small areas.
• If one area is dry, then it will have to be moistened again.
• It is necessary to tear off the wallpaper strips from the joints.
• When wetting, you need to turn off the electricity in the whole house (apartment).
• After wetting, it is recommended to walk on the surface of the wall with a spiked roller. Small holes will help water quickly penetrate under the finish into the adhesive layer.
• You can use the so-called wallpaper tiger, with the help of which not holes, but cuts will appear on the wallpaper.

Non-woven wallpaper is removed from the walls in a different way, because they are based on synthetic fibers. It is they who create a waterproof layer on the surface. It must be destroyed, for which you can use the same wallpaper tiger, or you can get by with the usual sharp knife. You just need to make deep cuts. Next, using a foam roller, you need to moisten the wall.

Vinyl is removed from the walls in the same way as non-woven. The thing is that vinyl is a durable waterproof polymer film that is applied to paper base. This film needs to be removed. By the way, after soaking, vinyl wallpaper should be pulled towards you, starting from the top. The tape is strong so it won't break. Paper may peel off from it, which sometimes remains on the walls in patches. They must be re-moistened and, using a spatula, removed.

The hardest part is removing the washable wallpaper. As in previous cases, it is necessary to damage the polymer outer layer with any tools. Next, the surface is wetted with water. There is no need to wait a long time, you have to try to tear them off the wall. If all else fails, then you have to use an iron. It is heated and the moistened wallpaper surface is smoothed with it. Thus, the destruction of the adhesive layer occurs.

And one more recommendation, which concerns the removal of wallpaper from a drywall surface. It should be noted that this process must be carried out very carefully, because the drywall itself is covered with a paper layer. It cannot be destroyed. Therefore, to quickly remove the wallpaper, you will need the same special liquid. But in this case, you can peel off the wallpaper, doing everything carefully.

Quick sticker method

One stick wallpaper, and even quickly, not easy. In order not to reduce the speed of the process itself, it is necessary to prepare well for it.

First, before gluing the wallpaper, the wall itself is prepared:

• It needs to be repaired: repair all defects with putty.
• Align using the same putty mortar.
• Prime the surface so that the surface has a high degree of adhesion.
• Mark out using a plumb line or level.

Secondly, you need to prepare right amount wallpaper and glue, as well as all the necessary tools:

• roller for applying glue;
• roller for smoothing wallpaper after laying on the walls;
• plastic spatula for the same needs;
• scissors or a knife for cutting material into strips;
• a sponge or rag to remove the adhesive that protrudes beyond the wall-mounted wallpaper.

Now you can proceed to the process itself, how to glue. To glue the wallpaper qualitatively, you need to cut them correctly.

Attention! The length of each wallpaper strip should be equal to the height of the wall to be finished plus 5 cm on each side. The allowance is cut off after drying. With the help of the allowance, it becomes possible to shift up or down the stacked strip, adjusting the patterns on the wallpaper.

Before gluing, on each strip with reverse side applied with a roller or brush adhesive composition. If it is necessary to glue non-woven or vinyl wallpaper, then the glue is applied to the wall. With them, the process itself is much easier. That is, take a strip, lay it on the wall, pressing upper edge according to the marked markup, and press down upper part hand. After that, a rubber roller is taken into the hands, with which the material is leveled and air is squeezed out from under it. To glue wallpaper in this way is not a problem for one.

Pasting paper wallpaper

With paper wallpaper everything is much more complicated. They must be treated with glue, then properly rolled up. It's done like this.

• The upper part of the strip folds inward by two-thirds.
• Down one third.
• The strip folded in this way must now be rolled up into a roll.

In this state, before gluing, the wallpaper should lie for about ten minutes so that the applied glue is well saturated in them. After that, the roll unfolds, but the edges remain in the same state (folded). The strip is laid on left hand, and the upper right edge is turned away and applied to the wall to the upper markup. By holding this glued edge, you can release the entire strip. Under its own weight, it will begin to straighten, and lie exactly vertically. It remains only to apply hands and a roller to straighten the material. The main thing here is that the edges of the wallpaper strip lie exactly on the markings applied in advance.

Conclusion

Many people think that fast is not always high quality. There is a lot of truth in this. But if the conversation is about peeling off and pasting the wallpaper, then this can actually be done quickly without compromising the quality of the final result. Watch the video - how to glue the wallpaper.