How to glue vinyl wallpaper on a paper basis. Heavy vinyl wallpaper

Before gluing vinyl wallpapers on the paper basis or non-woven base, you need to familiarize yourself with some of the intricacies of this work. Easy to clean, moisture resistant, durable wallpaper is noticeably different from the usual paper coating. Due to the PVC layer applied to the base, they are noticeably heavier than other types and require a slightly different gluing technology.

Preparing walls, tools and materials

As in any other case, sticking vinyl wallpaper with your own hands requires preparation:

• remove skirting boards;
• remove the previously applied coating from the walls: moisten the old wallpaper and remove it with a spatula, peel off the paint with a drill with a brush nozzle, wash off the water-based emulsion with a damp sponge;
• repair defects and level the surface of the walls;
• apply a deep penetration primer, after drying put thin layer putties, dry and process sandpaper;
• apply a new layer of primer for vinyl wallpaper, but if it is not available, it can be diluted with water to liquid state glue for vinyl on any basis.

In order not to be distracted in the process of work, you must first select the following:

• wallpaper of appropriate resistance to processing (determine by the icons on the roll packaging);
• adhesive for vinyl coating;
• brush for soil and glue;
• rubber roller;
• sharp knife or clerical cutter;
• plumb and tape measure;
• ladder;
• rag.

Before starting work, near one of the corners, use a plumb line to apply on the wall vertical line, from which the gluing of vinyl wallpaper will begin. You should pay attention to the base material. There are 2 varieties of it: paper and non-woven. The procedure for applying glue to either base is slightly different.

How to glue vinyl wallpaper with your own hands

The most important thing: to level and press the material when sticking paper-based vinyl wallpaper, you need a rubber roller.

This prevents the PVC layer from stretching, which, by shrinking as the paper dries, can tear it away from the wall. Negatively affect the "behavior" of the coating, after gluing vinyl wallpaper on a non-woven base and on paper is completed, temperature drops and drafts in the room where the repair is being carried out can.

The length of the cut should be 10-15 cm longer than the height of the wall from floor to ceiling. The rhythmic pattern on the wallpaper needs to be adjusted on adjacent strips before the piece is cut off. Sliced ​​adjacent panels must be folded together with the front sides inward.

Glue should be prepared in advance so that it has time to swell. Before sticking vinyl wallpaper, you need to pay attention to the index icons. One of them displays the method of applying glue: on the wall or on the base.

If the glue needs to be applied to the wall, then using a pile roller, you will need to evenly moisten with glue only that part of the wall where one strip will be glued. This method is usually used to glue non-woven vinyl wallpaper. For paper, it is often recommended to apply glue to the base. Lubricated strips must be folded in half lengthwise, with the adhesive side inward and allowed to stand for some time (indicated on the package). This is necessary so that the paper has time to soak with glue. Prepared strips can be glued to the wall.

Raise the first panel to the ceiling. It should be glued with a slight overlap on the ceiling, and the side should be aligned along the vertical line, which was marked by a plumb line. Smooth the surface, removing air bubbles from under the wallpaper. The next strip is aligned with the edge of the previous one.

Thick vinyl wallpaper should only be glued end-to-end, otherwise a noticeable scar will form at the overlap site, which will spoil the picture of a perfectly even wall. To get perfectly aligned edges of the strips, you can do in the following way: overlap adjacent strips and, until the glue has dried, sharp knife or use a cutter to make a cut in the center of the overlap. Remove the cut edges from above and from under the cloth, smear the edge with glue and roll with a roller. This will result in an almost imperceptible joint.

When rolling the panel with a roller, excess glue can get on the front side of the adjacent strip. To avoid this, it is necessary to spread the minimum amount of glue, rolling it with a roller on the wrong side of the wallpaper or on the wall. In the event that the glue still gets on the surface of the wallpaper, it must be removed immediately with a damp cloth.

After gluing the vinyl wallpaper is completed, the excess material under the ceiling must be cut along the ruler. lower part cut in such a way that an allowance of 0.5 cm remains. This part should be located on top of the plinth, covering the joint with the wall. It is important to remember that when making any cuts, the blade must be very sharp so as not to damage the still wet coating.

It is necessary to mention how to properly glue vinyl wallpaper in the corners of the room. When gluing the last strip on one wall and moving to the next extra part the cloth is bent on the mating wall. If the residue is very large, it must be cut so that an overlap of 3-4 cm wide remains. The first strip of wallpaper on new wall you need to glue, starting right from the corner.

As a conclusion

Introduced in the 70s, paper wallpapers with moisture resistant coating have come down to our days. Sometimes the question arises as to whether vinyl wallpaper is harmful. Compared with the products of half a century ago, manufacturers have mastered new way applying PVC to the base. Now the water-repellent layer is a microporous mass that freely passes air and allows the walls to “breathe”. This makes vinyl wallpaper indispensable and durable material convenient to use and maintain.

Any person who has minimal skills in such actions with wallpaper from other materials can handle gluing such a coating on the wall. To successfully complete the repair, you only need to carefully measure the strips of the desired length, combining the pattern on them, and do not forget that the vinyl cannot be stretched when gluing.

Related posts:

Vinyl wallpapers are ideal for both new buildings and for decoration during renovation. You will learn how to glue vinyl wallpaper from our article.

Tools and materials

For work you will need:

• A special brush or fur roller for priming walls and applying glue.
• Rubber roller for working with seams.
• Yardstick.
• Level or plumb line.
• Paper tape.
• Cotton rags (to remove excess glue).
• Scissors, knife for cutting fabrics.

Process details

How to stick vinyl wallpaper: work sequence

1. Preparing the walls

• The walls must be well dried before gluing, especially if plastering work was carried out before that.
• The surface should be without visible drops, potholes, chips.
• The walls are primed with diluted glue or deep penetration primer. It is preliminary recommended that the walls be treated with an antifungal compound (anti-fungus primer or any fungicidal compound).
• Clay gets divorced warm water according to the instructions on the package.
• A vertical line is beaten off using a level or plumb line, which will serve as a guide for gluing the first sheet.
• Then it is necessary to de-energize the room and remove sockets and switches from the walls.

Your attention! The walls are cleared old finish, cracks are puttied, and the surface is leveled. How to check if the walls are well dried? Glue a small piece polyethylene film if water droplets appeared on it overnight, the wall needs to be dried better.

You can also check the wall for the degree of preparation by gluing a piece of ordinary tape to it. Sharply removing it and viewing reverse side, it will be clear how the wall is prepared.

Wallpapering

The presence of paint or plaster residue on it indicates poor preparation of the surface or any other room.

Before gluing vinyl wallpaper, you need to make sure that there are no drafts in the room, in no case should you turn on fans and air conditioners, open windows until the canvases are completely dry.

It is impossible to stick canvases on old ones; they must be removed by moistening them with water beforehand. A similar procedure is followed.

2. Training

The rolls are cut into strips, leaving an allowance of 10 cm in length. If the coating has a pattern and its selection is required, when cutting the strips, you need to combine the pattern, not forgetting to leave an allowance.

3. We apply glue

After the wall is leveled and dried, the glue is prepared for application (it should stand for 10 minutes after stirring), you can start gluing the canvases.

Vinyl sheets are glued end-to-end, without overlapping sheets on each other. Glue is applied to the size of the first sheet, glued on and proceed to the preparation of the next section.

When gluing, make sure that no glue remains on the front side of the canvas, especially when working with light shades.

Your attention! When sticking vinyl flooring based on non-woven fabric, glue can not be applied to the sheet.

Before starting work, read the instructions on the package, and just that.

4. Trimming the edges

After gluing, an allowance remains near the plinth below and above, which must be cut with a sharp blade.

Advice! It is best to cut the coating when it is well dried, otherwise you will not be able to make an even, neat cut. The knife blade needs to be changed periodically.

Classic technology

Vinyl coating is best glued in a duet. One at the bottom cuts the canvases and applies glue to them, the other sticks a strip on the ladder-ladder and pre-applies glue to the wall.

The panels are pressed against the base of the wall and the bubbles are forced out with a roller from the center to the edges and from top to bottom.

If glue remains on the edges during gluing, you should immediately wipe them with a soft cloth or sponge.

Skirting board sticker

If it is not possible to remove the plinth, the sheets are carefully cut at its upper edge.

Work at the top

To prevent the glue from getting on the painted ceiling during work, you need to wrap the panel 5 cm at the top. After gluing the strips, glue this area, applying glue with a small narrow brush.

Corner finishing

Corner finishing options:

• You can glue the canvas in the corners with an overlap. This method is applicable for plain canvases and specimens with a small pattern. When gluing, the sheet is placed on the adjacent wall by 1 cm, this overlap is subsequently covered with an adjacent sheet. This sheet is also glued along a strictly vertical strip.

A special glue is used for gluing the panels with an overlap. The disadvantage of this method is the unaesthetic appearance of the corner.

• Another way - the work begins in the same way as the first method, but with a large (2-3 cm) allowance. After drying the canvases with a clerical knife, two sheets are cut vertically at once.

For this purpose, a spatula or a metal ruler is used, along which two layers of sheets are cut from bottom to top. The cut off parts are removed, the edges of the canvases are bent, glue is applied and rolled with a roller or plastic spatula. The seam in this case is perfectly even.

Finishing near batteries, switches and sockets

Advice! Behind the heating radiators, the wallpaper is let in 15-20 cm and pressed against the wall with a narrow roller. Behind the batteries, you can not stick canvases, but paint the wall to match.

In places where there will be sockets and switches, the gluing process takes place in the usual way. It is not necessary to pre-cut holes in the sheet, as they may not coincide with the technological holes for electrical outlets. This is done after gluing the panels.

Vinyl wallpaper on paper basis

The principle of operation differs little from the usual, with the exception of a few points.

Many people know how to glue paper-based vinyl wallpapers, as they have been traditional for a long time.

Glue is applied to the surface of walls and panels. On the sheets, the glue should impregnate the base; for this, the panel is folded face to face and left for some time.

Heavy vinyl wallpaper

This type of glue is somewhat more difficult than paper-based materials. It will not be easy to master this work on your own, especially if there is no experience in this matter.

Before gluing heavy vinyl wallpaper, purchase a special glue. We recommend using Quelyd, KLEO Line Optima or Metylan Interlining.

Such a finish stretches when wet and narrows when dry, which affects the quality of the seam.

The glued canvases should not dry too quickly, so the room temperature should not exceed 15 °C.

Summing up

We hope our article was useful to you. In order to more accurately understand the technological and practical matter, on our website there is a detailed photo and video instruction in which you will find useful information on this issue.

Photo gallery

How to glue vinyl wallpaper? This question is asked by many owners during cosmetic and overhaul, because it is vinyl already long years most valued among different types wallpaper.

The best value for money, durability, resistance to impacts and scratches, the most unusual colors and patterns - all this is vinyl.

Sticking a vinyl sheet with your own hands is a rather troublesome business, but it’s quite possible to cope if you prepare the surface well and study all the nuances of such a wallpaper repair.

Advantages and disadvantages

They are produced in the form of rolls with a base of paper web or better and more durable non-woven fabric, on top - a decorative layer of vinyl (officially - polyvinyl chloride).

This coating has several varieties, but they are all famous for a number of common advantages:

• strength (due to two layers of canvas, it is almost impossible to tear the vinyl when gluing or already on the wall);
• durability (perfectly kept on the wall for up to 10 years, while maintaining the original brightness);
• moisture resistance (some types of vinyl can be wiped with a cloth and even washed);
• versatility (you can choose a coating for any interior, find an imitation of any coating - wood, fabric, brick, etc.).

Among the disadvantages of vinyl are toxicity, airtightness and heavy repairs, but in fact - not everything is so dangerous.

Toxic fumes after finishing can appear only in wallpaper of dubious quality- proven non-woven vinyl is absolutely safe for health.

This coating is also highly breathable, unlike a heavier paper backing that can encourage mold and mildew growth.

Gluing vinyl wallpaper with your own hands is really not easy, especially in the absence of experience, but if you choose a light coating on non-woven, rather than paper-based, then the gluing process will be much easier.

Features of gluing different types of material

Where to start sticking vinyl wallpaper?

Many will say that from a window or from a wall and they will be almost right. But in fact, you need to start by choosing a type of vinyl sheet.

On the repair market, you can find several subspecies of such a coating, each with its own characteristics.

• Structural (with a layer of foamed vinyl). Such wallpaper is usually pasted over not smooth walls, as well as wood, plywood, fiberboard. The canvas helps to smooth out all the bumps and defects and creates a spectacular play of light on the surface;
• Hot stamping (heavy and compact vinyl). Such dense wallpapers are produced in the most unusual colors and textures. They perfectly hide all the unevenness of the walls and last as long as possible without losing their original appearance;
• Silkscreen. These rolls are produced on a paper basis. Stickering such wallpapers with your own hands is not an easy process: heavy silk-screened canvases are glued end-to-end, without overlap, and besides, when dried, they can shrink. But they are very durable, resistant to abrasion, look invariably expensive and stylish;
• Washable. Such vinyl is commonly used for kitchen renovations;
• Solid (evaporated). Consists of three layers of paper and evaporated vinyl, often used for painting.

Preparing for wallpaper repair

How to glue vinyl wallpaper with your own hands and what is needed for this?

You need to start by preparing a bridgehead for repairs - get rid of all traces of the old wall covering: greasy dirty wallpaper, crumbling putty and plaster.

Even if it is planned to paste the wall with embossed vinyl wallpaper, it is necessary to smooth out large cracks and bumps with putty, as well as prime the surface so that the vinyl lies tightly and does not peel off.

If wide vinyl wallpapers are used for wall decoration, it is important to ensure a perfectly flat surface.

Before you glue vinyl wallpaper with your own hands, you need to prepare:

• sharp scissors or a special wallpaper knife;
• pencil, suspension with a piece of chalk, ruler;
• a wide brush for glue and a thin brush for joints;
• wallpaper (plastic) spatula and rubber roller (smooth heavy canvases);
• clean dry cotton cloth;
• wet sponge;
• a bucket for glue and glue itself;
• ladder;
• several old newspapers.

Before gluing vinyl wallpaper with your own hands, you also need to de-energize the room and close all windows and doors tightly so that drafts do not walk in the room.

Then you need to properly prepare the glue and cut the wallpaper. Special glue for vinyl wallpaper is diluted according to the instructions and waiting for the solution to swell.

In the meantime, you need to prepare the wallpaper strips: cut the roll into separate canvases along the length with an allowance of 10 cm, spread them on old newspapers, smear with wallpaper paste and leave to “ripen” for 7-10 minutes.

Vinyl wallpaper gluing: work technology

How to glue vinyl wallpaper in a room with your own hands? It is best to do this together - with a reliable assistant.

First you need to draw a vertical line on the wall with the help of a suspension - the first strip will be glued along it.

The process of gluing the wallpaper will look like this: one person takes the wallpaper soaked with glue for upper part, gives it to a partner standing on a stepladder.

He applies a piece of vinyl roll to the wall, unfolds the panel and aligns the wallpaper.

It is necessary to glue vinyl only end-to-end, even minimal overlaps are strictly prohibited.

Then the strip must be smoothed out with a rubber roller or spatula.

A spatula is ideal for a smooth canvas, a roller is used for foamed vinyl and other embossed wallpapers so as not to damage the pattern.

Where to start smoothing the canvas to expel trapped air and remove excess glue? It is better to move from the center to the edges from top to bottom in order to squeeze out all the bubbles.

Excess glue must be quickly removed with a cloth so that it does not get on the front side of the wallpaper.

Excess wallpaper that remains below should be cut off after drying, otherwise the wet canvas will wrinkle and may even tear.

Wide vinyl wallpapers are glued in the same way as strips of standard width.

The only caveat is that if you have chosen wide wallpapers, then it is convenient to use 2 stepladders when working. This will provide perfect alignment wallpaper on the walls and make it easier to lay them end-to-end.

Where to start wallpapering?

It is better to lay a vinyl sheet on the wall from the corner of the wall perpendicular to the window, light wide canvases - from the window in the direction of the incident light.

This will allow you to glue the wallpaper exactly end-to-end, clearly connect the pattern and create the effect of a solid coating.

We glue vinyl wallpaper in problem areas

If the process of pasting the walls themselves with heavy vinyl looks quite clear, then how to glue vinyl wallpaper in problem areas and where to start work?

The most difficult areas for do-it-yourself wallpaper repairs are the corners, the space behind the battery and the switch sockets.

Where to start wallpapering the corners with your own hands and how to do it - end-to-end or overlap?

To make the corners look beautiful and not lose their appearance after drying, you need to act according to a special scheme.

We glue two panels on the corners with an overlap of 2-3 cm (if the corners are uneven, you can increase it to 5 cm).

Then, with a sharp clerical knife, we cut both pieces vertically - along a ruler or a long spatula.

Carefully remove the upper unnecessary strips, bend the edges of both canvases, coat with glue, lay them back on the wall, connect the pattern and roll it with a roller (spatula).

After drying, the corners will remain perfectly even.

It is not necessary to lay the vinyl completely behind the batteries - it is enough to glue 15-20 cm on both sides.

If you definitely want to decorate the area behind the radiator with wallpaper, then you can cut pieces of the canvas into several narrow parts - this will make the job easier, especially if wide wallpapers are used for decoration.

Places for sockets and switches, when pasting walls with vinyl wallpaper, need to be cut out only on the wall - if you make holes in advance, they may simply not coincide with a real outlet.

On the glued strip, mark the right place, make cuts crosswise and bend the corners inward.

After mounting the switches and sockets, the excess vinyl can simply be cut off.

We will send the material to you by e-mail

Wallpapering is important part any repair. This process differs in laboriousness and complexity. Many people are interested: how to glue paper-based vinyl wallpaper. At the same time, it is important to choose quality glue, since when using a low-quality composition, everything will need to be finished again. Features of gluing depend on the selected material. Vinyl panels are popular, which are characterized by reliability, wear resistance and UV resistance. Before you purchase the material, you should find out the features of working with this material.

Finishing with canvases vinyl backing provides an opportunity to apply unusual design tricks

Gluing consists of the following steps:

• walls are being prepared;

• a primer is applied, with the help of which shortcomings are repaired and miniature irregularities are hidden;

• glue is diluted in the container. You should get a solution without lumps and clots;

• using a level, a line is drawn for gluing the first sheet;

• electricity should be turned off in the room, and all switches and sockets should be removed from the walls;
• each roll is cut into strips;
• applied to the workpiece adhesive composition, while not leaving dry places;

• a solution is also applied to the surface of the wall;
• sheets are glued end-to-end, without allowance;

• excess glue is removed with foam rubber or a soft cloth;

• the edges are trimmed with a clerical knife.

Useful information! There should be no drafts in the room. The fabrics will dry for two days.

Related article:

Secrets of the correct gluing of the ceiling

The ceiling surface must be glued before pasting the walls. In this case, it is worth choosing lighter materials.When processing the ceiling, it is worth taking out all the items and carpets. If items cannot be taken out, they are covered with plastic wrap.

For your information! Vinyl is an excellent conductor of electricity, so it's important to remove any exposed wires.

How to glue the material in the corners?

Corners require special care. When to corner zone if there is a distance less than the canvas, then the sheet is cut off with an overlap. This part will move to the perpendicular wall surface. Then the second layer is overlapped. Sheets are passed by a special roller.

How long does paper-based vinyl wallpaper dry?

Drying time depends on dryness working surface and temperature values. If the humidity is exceeded and the temperature is slightly lowered, then the finish will dry for a long time.

Also, the drying time depends on the type of glue, the amount of solution used and the microclimate in a particular room.

Non-woven surfaces can dry within a day, and paper surfaces for a shorter time period.

Useful information! When drying, the canvas with a paper base can shrink significantly, so you need to make sure that the seams do not move out.

With the help of vinyl wallpaper, you can create a stylish and original interior. When choosing a texture and pattern, you should use the original design solutions and various combinations.

Save Time: Featured Articles Every Week by Mail

In this article, you will learn what tool is needed for wallpapering, how to glue vinyl wallpapers correctly so that they last as long as possible, about the difficulties of pasting walls in the corners of internal and external, how easy and not too tired to glue vinyl wallpaper on the ceiling and what kind of glue glue vinyl wallpaper on a paper basis.

Wallpaper can be glued different ways and technology, I will tell you how to glue paper-based vinyl wallpaper correctly.

Let's start with the tool:

1. Plumb or level mark a vertical line on the wall with a pencil or marker
2. Small brush and mop to apply glue to the wall and wallpaper, you can also use a roller with short and medium pile
3. Knife or scissors with a ruler, tape measure, cut the fabric and cut off excess wallpaper on the wall, as well as cut holes for switches and sockets
4. Large and small rubber roller, for smoothing the canvas on the wall.
5. Stepladder or table
6. A rag or thick foam rubber, remove excess glue that has come through the joints.

This is the main tool that you will need for wallpapering, you can replace some of the tools with what you have at home, but then the quality of wallpapering will suffer. You can replace the rubber rollers with a regular rag, in which case you risk damaging the vinyl layer or breaking through the wallpaper. You can take a small brush instead of a maklovitsa and smear the walls and canvases with it, but then you will be much longer and more tired to glue the wallpaper.

You need to start gluing any wallpaper, including paper-based vinyl ones, with preparatory work. Despite the fact that the wall will hide under the wallpaper and will not be visible, smooth and even walls are the key to a clean and beautiful view wallpaper. Pay more attention to the preparation of the walls and at the end of the repair you will enjoy the look of the wallpaper.

Remove old wallpaper, scrape off patches and sagging of old plaster, putty the wall in several layers and go over with sandpaper to make a clean and even base, then prime the walls so that the putty adheres firmly to the wall and does not fall off with the wallpaper, in addition, this will help prevent mold and fungus.

When the walls are prepared, you can begin to glue the paper-based vinyl wallpaper. Dilute wallpaper paste in water in the ratio of 1 part glue: 55 parts of water, this will be the adhesive preparation of the wall surface. Coat with this composition all the walls and ceiling where you will glue the paper-based vinyl wallpaper. This is necessary so that the walls are saturated with glue and hold the wallpaper more firmly. Let the primer dry for a day and start gluing the wallpaper.

Using a plumb or level, draw a vertical line on the wall, this will be the starting line from which you will begin to glue the wallpaper. The line can be drawn anywhere on the wall, no matter where you start gluing, paper-based vinyl wallpapers are always glued end-to-end and the “glue from window to door” rule is not relevant here, because the joints will not be visible, no matter where you start gluing.

Find yourself an assistant, it will be problematic to glue vinyl wallpaper alone.

When the glue swells, mix it again and start smearing the wall and canvases. First smear the first canvas and fold it with the smeared parts together so that the wallpaper base is saturated with glue, set it aside.

Further, one person spreads the wall, the second one spreads the second canvas and folds it like the first one, then the first canvas is taken and glued onto the plastered section of the wall, the edge of the canvas is clearly aligned with the vertical line that you drew at the beginning. If you have a straight line between the ceiling and the wall, you can glue the wallpaper point-blank to the ceiling, but if the line is crooked, you will have to make an overlap and try not to stain the ceiling with the glue from the wallpaper.

Smooth the canvas on the wall very carefully without pressing hard, paper-based vinyl wallpapers tend to stretch when wet and shrink when dry. If you do not stretch them too much when sticking, then, when they dry, they will not come apart at the seams.

In the same way, continue to stick the rest of the wallpaper.

How to glue vinyl wallpaper on a paper basis in the corners

Corners are the most problematic area when wallpapering. Here you need to act very carefully. As I wrote above, we prepared the walls well and now we have even corners and it will be easier for us to glue the wallpaper. If the corners are curved, it will be difficult.

The main thing you need to know when you glue vinyl wallpaper in the corners, one of the joints must be cut through. That is, when one roll or less remains to the corner, measure this distance and add 3-4 centimeters to it, make a canvas along this width and stick it on the wall so that those 3-4 cm are found on the second wall. Then, on the second wall, draw a vertical line at the width of the canvas from the corner, and glue the next canvas along this line. In the corner we got an overlap. Now, carefully with a sharp knife along the ruler, cut two canvases in this place and remove the trimmings, we have a joint. Now well coat with glue at the junction and smooth. In this case, most likely, you will get a shift in the picture, but it will not work in another way, unfortunately. You can try to reduce the drawing, maybe it will work.

What is the best way to glue paper-based vinyl wallpaper on the ceiling

Since the vinyl wallpaper will hang on the ceiling, it is better to take not heavy, but light paper-based vinyl wallpaper, this will reduce the load on the adhesion of the adhesive wall and wallpaper, which means the wallpaper will last longer.

In general, there is no difference in gluing wallpaper on a wall or on a ceiling, except that you need to keep your hands constantly on weight, and this makes them and their backs very tired. Therefore, breaks should be taken more frequently.

There are a few points that need to be mentioned, despite the fact that we seem to have a starting line in the form of a wall, but we have to draw our own line, we do not know how straight our wall is. If you are 100 percent sure that the wall is straight, you can glue it point blank, if not, draw a straight line on the ceiling along the wall at a distance of 10 centimeters less than the width of the roll, when you stick the first roll, aligning it along the line, you will have to do overlap on the wall, do it carefully so as not to stain the wall wallpaper with glue. You can play it safe, stick newspapers or film on the wall with masking tape, so the glue will not stain the wallpaper, and after sticking you can remove this protection without leaving a trace. But use only masking tape, clerical tape will not work here, it leaves traces.

How to glue vinyl wallpaper on a paper basis

Is it possible to glue paper-based vinyl wallpaper with non-woven glue - no, it is not possible, non-woven glue is specially designed for non-woven fabric and will not stick to the paper base. You can glue paper-based vinyl wallpaper with any glue for paper wallpaper. Glue for paper-based vinyl wallpaper has several main names, “Universal” (universal premium) and “vinyl” (premium vinyl, special vinyl), express (super express). All of these types of adhesives are well suited for bonding paper backed vinyl embossed profiled wallpaper, heavy paper backed vinyl wallpaper and any paper backed wallpaper. Methylan also offers premium granulate adhesive specifically for heavy paper-backed vinyl wallpapers. To be frank, you can glue paper-based wallpaper, both heavy and light, with any glue for paper wallpaper, you just need to increase the amount of glue in the mixture. That is, if the wallpaper is heavy glue, add more to the water and make the mixture thicker. For example, “Moment” writes that the same adhesive for vinyl paper wallpaper “Moment Classic” must be diluted in a ratio of 1 part glue: 35 parts of water, if the wallpaper is light, if the wallpaper is heavy, the ratio should be 1: 25.
In terms of the quality of glue, everything is traditional, the more expensive, the better.