How to hang wallpaper on old walls. How to glue wallpaper on old wallpaper

Tsugunov Anton Valerievich

Reading time: 5 minutes

Tired of old wallpapers? So, it's time to update the look of the room and start an easy one. The process of sticking wallpaper material itself is simple and does not take much time, the most tedious and time-consuming part of the work is often the removal of the old coating and surface preparation. Against this background, a natural question arises: is it possible to glue wallpaper on old wallpaper, and if so, in which case?

To get a decent result, the old canvases are removed, the wall is leveled, degreased and primed. But to save time, effort and finances, the preparatory stage is sometimes omitted by gluing new wallpapers onto the previous ones.

When can I glue new wallpaper on the old

In principle, it is possible to apply material to an already pasted wall, but only under the following conditions:

• the existing finishing material, on top of which it is planned to mount a new one, must be paper;
• previously glued canvases must be firmly attached to the wall, not move away at the joints and not have defects;
• the surface on which new strips will be glued must be smooth, without a relief pattern;
• it is highly desirable that the old material be thin and single-layered.

The requirements for an already applied wallpaper coating and the rules for gluing photo wallpapers on it are described in .

New wallpaper for vinyl flooring: is it possible or not?

You can not attach new wallpaper directly to it. Regardless of the type of adhesive you choose, it's likely that it just won't work because the synthetic coating is water-repellent. This is especially true for washable wallpaper. In addition, most vinyl materials have a textured pattern that will show through a fresh layer of finish.

How to choose material for pasting on old wallpaper

What wallpaper is suitable for gluing over the previous ones? When choosing, the intensity of the color and the brightness of the pattern on the old canvas are taken into account. If the new gluing material is lighter than the previous one, then the color of the bottom layer will show through. The following tips will help you choose:

1. The material is selected darker than the coating glued earlier.
2. Too thin canvases are not suitable, the old pattern will show through them.
3. Non-woven wallpaper cannot be used for the top layer: they often have a translucent structure.
4. Handle vinyl material with care as it is quite heavy and there is a risk of it falling off the wall along with the base layer.
5. It is better to stay on a canvas of embossed paper, as in the next photo: on a smooth surface, possible flaws will be especially noticeable.

Gluing rules

Important! If a small amount of bubbles appear on the surface after gluing, do not despair. You can try to smooth them out with a special spatula or even a simple iron. No need to be too zealous - after the surface has completely dried, they can smooth out by themselves.

What to do with liquid wallpaper

After we have dealt with the paper, vinyl and non-woven base, we will find out whether it is possible to glue new canvases on liquid wallpaper. This is essentially not a wallpaper in the standard sense, in terms of properties they are more reminiscent of the presence of cellulose in common with a paper web. Since this material, applied in a layer of a few millimeters, creates a fairly even surface, it will serve as a suitable base for gluing a new finish. In addition, the cellulose will absorb some of the water from the adhesive, which will also help the material adhere well.

In order for everything to work out as it should, consider a few important points:

1. The layer of liquid wallpaper should not be damaged, any flaws must be corrected.
2. If there are voids under separate sections of liquid wallpaper, they must be opened, smeared with glue and the surface dried.
3. A primer applied to the wall will significantly improve the adhesion of materials.
4. The relief structure of liquid wallpaper can cause poor-quality results; the new finish will look good only on a smooth base coat.
5. On a surface with a pattern, it is better to glue a dense material of a saturated or dark color, but not light.

HELPFUL INFORMATION: What wallpaper will make the bedroom beautiful and cozy

Wallpapering is the most common option for home renovations. Ease of installation and availability of materials allow you to do the work yourself. In this article, we will tell you in detail how to glue wallpaper with your own hands, starting with the choice of materials and glue, ending with the tricks and advice of experienced maters.

Wall preparation

The preparatory stage should begin with the release of the walls from all unnecessary items. Sockets and switches, skirting boards, as well as door paneling must be dismantled to simplify work.

Let's do everything with our own hands!

We carefully prepared this article before publication, and therefore we will tell you about all the nuances of self-pasting walls: how to choose glue, how to apply it, how to stick it, etc.

It is recommended to de-energize the room to prevent electric shock during wet work. If this is not possible, it is necessary to carefully insulate the wires of switches and sockets, and hide them in the sockets.

old wallpaper

Then you should do the preparation of the walls. If the walls are finished with old wallpaper, they will have to be torn off. First, they are removed by hand, and if you're lucky, the strips will come off entirely, but usually they come off badly, in separate pieces. The fragments remaining on the walls are recommended to be moistened with warm water and cleaned with a spatula.

Difficulties may arise with vinyl samples, with a moisture-resistant coating on the front side. It must be removed so that water can penetrate to the base and soak the glue. This will take a lot of time, but then the material will become more pliable and can be easily cleaned with a spatula.

Paint cleaning

If the walls are painted or whitewashed, the cleaning job becomes more difficult. Whitewash should be moistened with plenty of water and gradually removed with a spatula. Oil paint is harder to remove and takes longer, but there are ways to speed up the process. Firstly, you can use special chemical compounds to remove paint, and secondly, use construction power tools.

The chemical method of removing paint will be expensive, and will require the use of personal protective equipment, due to harmful fumes. As auxiliary tools for removing paint, a grinder or a puncher with special nozzles in the form of metal brushes can be used. In this case, a respirator and goggles are also needed due to the abundance of dust.

alignment

When the room is cleared of the old finish, they begin to level the base. The amount of work at this stage depends on the condition of the walls. A wall with a small number of chips and small defects will require only local alignment. Minor flaws should be corrected with a finishing putty, having previously treated the wall with a primer for better contact.

Pronounced uneven walls will require more attention. Puttying will be required in two layers - starting putty to correct the main defects, finishing for final alignment. At the end, the walls are sanded with an abrasive mesh and cleaned of a layer of dust.

Types of wallpaper

Now on the market of finishing materials there are many options for wallpaper that have certain performance characteristics, advantages and disadvantages. Let's highlight the main types:

• Paper wallpaper. The most common type, characterized by low cost and ease of pasting. Paper wallpapers are eco-friendly and great for bedrooms and children's rooms. On the other hand, they cannot be washed and they do not retain their original appearance for long;
• Non-woven wallpaper is made on the basis of paper with the addition of non-woven fibers. Differ in durability, wear resistance and not be afraid of water. Gluing non-woven wallpaper is simple - the glue is applied directly to the walls. This finishing material is able to hide minor wall irregularities, which simplifies the process of leveling the base;
• Vinyl wallpapers consist of paper or non-woven backing covered with a vinyl coating. They are easy to clean and do not lose their brightness for a long time. Before gluing non-woven vinyl wallpaper, it is worth considering that they do not “breathe”, and it is not recommended to use them in children's and bedrooms;

• Acrylic finishing material is paper coated with an acrylic compound. Unlike vinyl wallpapers, they have a thin outer layer, and are not as durable, but they are better breathable;
• Natural. This type of wallpaper is characterized by environmental friendliness, exclusivity and high price. They contain natural cork, straw, reed, etc. Drawing on the walls requires some skill;
• Fiberglass material is ideal for office space. Differs in durability and durability, is not afraid of water and does not burn. After application, it is painted with water-based paints, and this can be done dozens of times;
• Textile samples consist of a natural fabric material applied to a paper base. They look chic and expensive, and cost accordingly. They are sensitive to moisture and mechanical stress, and also absorb odors well;

• Metallized wallpapers have an outer layer of aluminum foil, are not afraid of external influences and are easy to clean. Ideal for modern interiors;
• Liquid wallpaper is the most unusual type of all listed. They are based on cellulose, supplemented with decorative dyes, fibers, sparkles. Walls before applying such a coating may not be leveled. It is not recommended to glue them in wet rooms, due to hygroscopicity;
• Wall mural is a self-adhesive film on which a certain pattern is applied. You can depict everything on the wallpaper, from an ornament to a photograph, which allows you to make the room unique.

As a rule, wallpaper for the room is selected based on taste preferences, but in order for them to last longer, their features must also be taken into account.

Wallpaper glue

The selection of glue causes difficulties for many who started repairs with their own hands. In fact, the variety of options presented should not scare anyone, because in order to make the right choice, it is enough to focus on the type of wallpaper used. There are several types of wallpaper glue, which differ in composition:

• methylcellulose glue;
• CMC glue, based on carboxymethyl cellulose compounds;
• starch glue.

The choice of glue is made on the basis of the following features:

• wallpaper type;
• microclimate of the room;
• wall material.

First of all, you should decide on the type of wallpaper. Manufacturers of adhesives offer a wide range of products on the market, from which choosing the right option is not a difficult task. According to the type of compatibility with wallpaper, glue is:

• for light wallpaper (paper);
• heavy wallpaper (fiberglass, textile);
• non-woven wallpaper;
• vinyl samples;
• universal, suitable for all types.

How to choose the right glue, taking into account the microclimate of the room? Materials for wet rooms must be resistant to moisture and retain their properties under any conditions. In addition, damp rooms contribute to the spread of fungus and mold. The adhesive composition must contain antiseptic substances to prevent their occurrence.

How to glue wallpaper with your own hands

Wall decoration with wallpaper is a procedure that you can easily handle with your own hands, but it is important to follow certain rules so that the result is of high quality, and the process itself does not take much time and effort.

Final preparations

Before gluing the wallpaper, you must go through the last preparatory stage - priming the walls. Priming allows you to achieve better adhesion between the base and the finishing material. For the production of works, you can choose an acrylic primer or use glue. Manufacturers of adhesives indicate on the packaging how to properly dilute it, for pasting or priming walls.

The composition is applied to the walls with a roller, and the corners are processed with a brush. It is recommended to prime immediately before work, so that dust does not have time to settle on the walls, which can impair adhesion. It is also worth providing the necessary conditions in the room itself. For the duration of the work, up to the complete drying of the glue in the room, the windows should be closed.

The most optimal room temperature is 20 degrees. It is also necessary to put things in order, wash the floor, so that during manipulations with the wallpaper they do not spoil their appearance.

Where to start gluing

From which wall the pasting process will begin, by and large it does not matter. The main thing is to stick the first strip strictly vertically. If there is no desire to beat the level, it is allowed to take some obviously vertical object (window slope or door jamb) as a guide. You can start gluing in the corners. The remaining strips will be glued already according to the reference first one and the fitting process will be simplified.

How to prepare glue

All modern adhesives have instructions on how to stick wallpaper on the back of the package. It is necessary to carefully study it before gluing the wallpaper and follow all the recommendations. As a rule, the preparation process is reduced to the dilution of dry glue in water, in the proportions indicated on the package. To prevent the formation of lumps, it is necessary to add glue to the water in small portions, stirring the resulting composition thoroughly.

How to glue wallpaper

First of all, you need to find information on the rules for applying glue on the wallpaper packaging. If the adhesive is to be applied directly to the strips, they must be rolled up with the smeared side inward. The edges are folded to the middle several times. The folds should remain rounded and the wallpaper strip should resemble a scroll.

If, according to the technology, glue is applied to the wall, then it is necessary to coat the base along the width of the glued strip with a margin. To apply glue in the corners under the ceiling and floor, use a brush.

Having climbed onto the stepladder, it is necessary to launch a few centimeters of the glued strip onto the ceiling. The edge of the strip must be aligned with the marked vertical or landmark. Then, with smoothing movements from the landmark to the opposite side, glue the strip near the ceiling.

with a special soft spatula. When gluing wallpaper, it is necessary to monitor the formation of air bubbles, be sure to expel them with excess glue to the edges.

The remaining parts are also glued, only you need to focus on the already glued strip. At the end, you need to cut off the extra parts in the corners near the ceiling and floor. The easiest way is to use a wide spatula and a clerical knife. The spatula is applied to the corner, and the resulting margin is cut off along its edge. As a result, the edges are smooth.

Separately, it is worth mentioning how to stick wallpaper in the corners. There are two ways. The first one involves gluing one strip overlapping on the other side of the corner with a margin. The second strip is cut off at the corner and glued directly onto the stock. If the material is thick, the joint will be very noticeable, and it is better to use the second method.

To achieve a more inconspicuous joint in the corners, the strips are overlapped on both sides and cut off with a sharp knife with a spatula. If the corners were glued tightly, then the stripes would line up perfectly evenly. The outer corners of the room are glued in the same way, using one of the methods.

How to glue wallpaper in the presence of obstacles

For those who understand how to stick wallpaper, difficulties may arise in areas near doors and windows. If the window or door is flush with the wall, it is enough to cut a strip of wallpaper along the casing or jamb with a small margin. Then, to the corner of the casing, the strip is cut at an angle of 45 degrees. The resulting parts must be hidden behind the design of the door or window, and cut off excess remnants.

If the door or window is located in different planes with the wall, the work becomes somewhat more complicated. First you need to glue the slope, leading a small margin onto the wall, cut along the edge with a spatula. Next, you need to glue the wall in the same way.

Also, difficulties may arise when bypassing sockets and switches. If they were dismantled before work, then only installation boxes with wires should remain on the walls, located flush with the wall, which will not interfere with the work.

If for some reason it was not possible to remove the wiring accessories, then it is necessary to attach a strip to the obstacle and mark its edges. Using a knife, cut out the necessary fragment according to the marks, leaving a margin that can be hidden behind a false decorative frame.

If you need to glue the wall behind the battery, it is not necessary to remove it. It is enough to get a certain supply of wallpaper from all edges for her. You may also need information on how to properly bypass heating pipes. If they weigh on clamps, you can dismantle them for convenience, and put them in place after the work is completed. Holes in the walls will not be difficult to find.

How long does wallpaper dry

The drying time of the wallpaper depends on its type. Non-woven wallpaper dries for at least a day, and the thicker they are, the longer it takes to wait. Vinyl wallpaper dries for about two days, provided the humidity in the room is not more than 60%. Drying time for paper wallpapers varies from 24 to 72 hours. It is important to remember that at this time you should not open windows, and generally allow drafts in the room. By following these rules, you can hope for a quality result.

Frequently asked Questions

• Is it possible to glue wallpaper on wallpaper? - This is allowed only in certain cases. If the old samples are thin, then most likely they sit firmly on the walls, therefore, they will be a good basis for a new finish. However, how long such wallpaper will hang is a big question;
• How much do the services of masters cost? - On average, finishers estimate their work from 150 to 170 rubles per glued square meter;
• What to do if the wallpaper peels off? - You can use a brush to glue the detached part with the remnants of glue, or use special glue for seams;
• What happens if you ventilate the room during and after work? - It may happen that in a draft the glue dries too quickly, and the material does not have time to stick.

Everyone dreams of equipping their home in such a way that it is cozy, compact, and most importantly, practical. Now in the markets and in online stores, many materials are sold that make our life comfortable, in particular, these are wall murals. There are many nuances on how to glue them correctly and in general, what additional tools to use. Let's take a closer look at all the subtleties of this case, so that the result justifies all the efforts invested in it.

Photo wallpaper gluing technology next:

• level the surface before starting work;
• prime thoroughly;
• treat with glue that is specially used for vinyl wallpaper;
• apply glue to the photo wallpaper with the image down, using a meaty roller;
• after that, fold them in half and let them soak for 2 minutes;
• attach to the wall and walk with a rubber spatula, and then with a rubber roller;
• grease the edges and smooth with a rubber spatula;

• then repeat the procedure until a complete picture is formed;
• after gluing, you need to retouch everything, for this, take a pencil of the desired color, chop it with a blade and carefully go through the seams;
• the temperature in the room should not exceed 19°C;
• close all windows and doors tightly until the glued sheets are completely dry.

Follow the above points, and your work will bring you great joy and pleasure, the main thing is to tune in to a positive result.

What kind of glue to glue photo wallpaper - proportions and application technology

There are 2 types of glue for this type of work:

• Adhesive for non-woven, vinyl and textile rolls (heavy types). The proportions and technology of application depends on the surface area on which the wallpaper will be pasted. If, for example, the area is 70-80 m2, then in this case the glue must be diluted in proportion 1:35 , the amount of water per pack is 9.45 liters. If you need to glue 30 m 2 , then the proportion will be 1:25, and the amount of water will be 6.25 l.

• Glue for paper sheets (light wallpaper). To do this, you can use ordinary glue, which must be diluted strictly according to the proportions indicated in the instructions. Pour the contents of the pack into water and stir for 35 seconds. After 10 minutes, stir the mixture again and you can safely use it.

The only thing is that in the first case, you apply glue only on the wall, and in the second: both on the canvas and on the wall. Then you can get great results. Do not experiment, but act clearly according to the indicated instructions.

On which wall to glue the wallpaper?

You choose the wall on which you want to see a beautiful picture. The main thing is to process it correctly. After all, your future work depends entirely on it.

• Immediately before starting the process of applying photo wallpapers, the walls must be prepared in advance: apply a thin layer of plaster, then putty, carefully sand everything and be sure to cover with a primer. Also don't forget to mark up.

IMPORTANT: All walls must be smooth, without any irregularities and specks, because all this can be reflected in the main wallpaper pattern you have chosen.

• If you can’t level the walls with putty, then use drywall, so you can achieve perfectly smooth wall surfaces. People who have used such wallpapers say that the preparatory work plays a key role in this matter, and if quality is really important to you, and not speed, then you need to make a little effort, and you will get exactly what you dreamed of.

How to glue paper photo wallpaper?

Such wallpapers are much thinner than non-woven ones in their structure, so you need to give the glue some time to soak in so that they expand and the pattern is evenly distributed over the entire wall.

• After you have completed all the preparatory work, lay out the canvas as you stick it.
• If there are small white stripes along the edges, then, if desired, they can be cut off in some places so that the pattern lies flat and does not protrude anywhere.

• Glue must be added by stirring the water with a whisk until a homogeneous mass is formed.
• It is best to use a special pallet for working with a roller. For these types of wallpapers, according to reviews, it is the roller with a small nap that is most suitable.
• The glue is applied in a uniform thin layer first on the wallpaper, and then directly on the wall, for a more convenient combination of wallpaper with each other.
• Be extremely careful, such wallpapers are overlapped. Each joint is wiped with a damp cotton cloth.

Do not rush, the main thing in this matter is accuracy and skill, then your work will always please you and cheer you up after a hard day's work.

How to glue non-woven wallpaper?

The main surface that you decide to decorate with beautiful non-woven photo wallpapers should be moisture-absorbing, without any protrusions and roughness, and also be sure to be uniform in color. After all, too bright, saturated color of the base can be seen through the wallpaper.

• The room itself should be well lit, and of course, avoid drafts, the temperature should not exceed 20°C. Before you get down to business, make sure that all the rolls you buy match in all respects and colors.
• If everything came together, draw two lines in the middle of the wall: horizontal and vertical, while using a plumb line and a level.
• There is a large selection of glue designed specifically for non-woven wallpaper. Dilute it to a thick consistency according to the technology described above. In this case, apply only to the surface of the wall, this will be enough.

• Glue each part of the drawing according to the drawn lines. Remove air from the center down using a soft cloth or soft roller, and excess adhesive with a damp soft cloth.
• Since this type of wallpaper is much thicker than ordinary paper ones, you need to glue them butt-to-butt, the pattern will be even, and no seams will be visible.
• If the edges protrude in certain places, then using a regular clerical knife, this problem can be easily eliminated without damaging the drawing. Drying should be slow to avoid divergence of the seams and the occurrence of cracks, it is necessary to observe the temperature regime.

According to reviews, following the correct wallpapering technology can guarantee that the wallpaper will last you much longer.

How to glue photo wallpaper from 8 parts?

Walls, as in the previous versions should be perfectly aligned, because the wallpaper will only emphasize all the existing bumps and roughness.

• To smooth out all the imperfections, you can use a special brush.
• If there are any recesses, then they must first be covered with putty, and then rubbed well with a brush.
• The temperature regime should not be higher than 19 ° C, so that all parts adhere well to the surface.
• Before starting the process, lay out all 8 parts of the picture, forming a complete composition. As in the previous version, draw a horizontal and vertical line on the wall.

• Dilute the glue to a thick consistency and apply it for no more than 3 minutes on the first part of the wallpaper. Glue them, then glue all subsequent fragments of the pattern with an overlap of 2-3 mm to the previous ones.
• Approximately the entire composition dries out in 10-12 hours, this is subject to strict adherence to all application rules.
• Carefully remove excess glue particles with a damp sponge. If somewhere the seams are not glued, then go again with a thin brush and lightly press with a rag so as not to damage the pattern applied on top.
• Carefully look at all the seams and, if necessary, also go through the glue again.

Is it possible to glue photo wallpapers on old wallpapers?

According to reviews , it is best that the walls are even, and there are no drawings and recesses on them. old wallpaper who have already served their better clean it up from the surface with a special knife. But, if you want to leave them, then before doing this, you need to take into account some important nuances in order to get an excellent result:

• textured ornament on them should not be more than 0.2-0.3 cm
• in this case, it is recommended to use the simplest method of sticking colored wallpapers with a density of not more than 250 g / m 2
• your old wallpaper must be resistant to moisture

If all the above parameters clearly match, then you can safely get to work. If for any one of the points there are discrepancies, then this method will not work for you and you should not waste extra time, nerves and effort.

Also consider the fact that, in this case, wallpaper depicting a beautiful, dense forest, tall and saturated with green grass, some metropolis, parks, fountains and lights, as well as plum, apricot, apple and pear orchards is best suited. . Due to their rich color and dense pattern, they perfectly overlap the background of old wallpapers.

Glue must be selected strictly according to the parameters specified by the manufacturers and recommended brands. The quality and service life of the photograph you purchased will depend on this.

Now the choice is yours. Considering all the recommendations and tips described above, you can create your own dream interior that will make your country house or your favorite apartment even more comfortable and beautiful. At the same time, you will spend only 4 hours on the work itself, which you can enjoy for many years. Moreover, now you can find everything that your heart desires, for every taste and color, and the pricing policy will pleasantly surprise you.

The number of repairs carried out on their own has increased significantly in recent years. This is due to the desire of people to save time and money. Very often, the question of savings arises when gluing new wallpaper, since many apartment owners do not know whether such a saving option is possible, and how to glue the wallpaper correctly in this case.

We will try to answer these and other questions about such wallpapering in this article.

When is wallpapering acceptable?

Why do many people try to leave the old cladding? There are several situations in which people decide to glue wallpaper on old ones:

1. Some try not to remove the old lining, mistakenly believing that the wallpaper on the wallpaper will stick better.
2. In some cases, peeling off old wallpaper is very difficult, and then the owner of the apartment decides to simply paste the wallpaper on the wallpaper.
3. Another reason is ordinary human laziness. Far from many people want to mess with the old finish for a long time, especially when the repair is done by hand.
4. An attempt to save money. For some reason, it is believed that the dismantling of the old cladding takes a lot of financial resources. When sticking new wallpaper, you spend only your time, warm water, putty and primer. But if you do not want to bear even such insignificant costs, then you can not remove the old wallpaper.

The advantages of such a sticker include:

• you do not need to level the walls;
• saving time on stripping wallpaper.

As disadvantages of this venture, one can name the following:

• the walls will not be aligned;
• bubbles may appear;
• the service life of glued wallpaper is reduced;
• new wallpaper may simply not stick;
• new wallpaper may peel off along with the old.

Features of the work

If you still decide to glue wallpaper on wallpaper, then keep in mind that although this process is not considered too complicated, there are some nuances in it that you should definitely pay special attention to.

There are a couple of very important things to keep in mind:

1. The wall must be strong and very even, without any defects. If such defects are found, then it is not worth the risk, it is better to get rid of the old wallpaper. Therefore, you will have to carefully examine the walls before gluing in order to detect hidden and obvious defects:

   • obvious defects - differences in the plane, tears and peeling off part of the wallpaper, as well as abrasions;
   • hidden defects - cracks and voids in the walls, which are easily detected by tapping the walls with a hammer.
2. Before gluing wallpaper on old wallpaper, certain manipulations should be done, such as gluing lagging seams and sealing cracks and cracks with putty and primer.

Advice. You can wash the wall with ammonia solution, and then let it dry well.

If major defects have not been identified, and minor ones have been eliminated, then you can safely proceed to gluing new wallpapers onto old ones. However, this requires advance. You will have to glue new wallpapers in compliance with all technological rules, based on the requirements and norms of the repair process.

Tools and materials

Before sticking wallpaper on wallpaper, we will carry out preparatory work, so that later we will not be distracted by them.

You will need these tools:

• Tray and roller, with which we will apply glue on the back of new wallpaper or on walls with old wallpaper;
• Wallpaper or ordinary household scissors;
• Sharp knife for cutting corner joints;
• Rubber spatula for leveling wallpaper;
• Clean rags for wiping glue;
• Wallpaper table with a horizontal flat surface. In the absence of such a table, the floor can perform its function.

Important: gluing wallpaper on wallpaper is allowed only in the case of paper wallpaper.

Gluing stages

1. In order to stick wallpaper on wallpaper correctly, we first prime the surface of the walls. For the primer, you can use the same glue that is intended for the gluing process itself. We prepare the glue in a slightly more liquid version than for gluing, after which we apply it with a paint roller in one layer.



2. During the complete drying of such a primer, you can prepare canvases of new wallpaper:

   • if you have a standard roll, then you can simply cut it into 3 canvases;
   • if your new wallpaper has a pattern, then you will have to cut the canvases so that the pattern on 2 adjacent canvases matches.
3. • when laying vinyl wallpaper, glue is applied to the wall;
   • when laying paper wallpaper, the glue is evenly distributed on the reverse side of the canvas.



4. The further process is completely similar to the process of conventional wallpapering:

   • Finishing can be started from any corner of the room;
   • Installation of canvases starts from the ceiling;
   • The wallpaper must be attached to the wall, and then leveled with a rubber spatula.
   • The second canvas is laid in the same way.

Laying different types of wallpaper is significantly different:

• paper wallpapers are usually overlapped;
• - butt.

How to glue wallpaper in the corners

The most difficult moment of the whole process is pasting the corners of the room. Here's how to do it right:

1. One of the canvases is trimmed with an allowance of about 5-6 cm.
2. The glue allowance is not processed.
3. The second canvas on the other wall is laid with the same allowance.



4. With a sharp knife in the corner, an incision is made vertically along these two canvases from ceiling to floor.
5. Allowances are removed from them, and the joints are treated with glue on the inside and smoothed out with a spatula.



Advice: When wallpapering wallpaper on wallpaper, the spatula is always carried out from the center to the joints.

One of the most popular types of interior decoration is wallpapering. But in order for the result to please, you need to know how to glue the wallpaper correctly. There are a sufficient number of nuances that affect the quality of the finish.

Preparatory stage

First, everything that can be removed in the room is removed, including door frames and baseboards, if possible. They also remove sockets and switches, closing the boxes with wires with plugs - plastic or wooden.

Turn off electrical outlets

When working with an electrician, we de-energize the room and do not turn it on until we finish. It is advisable to carry out all work, including wallpapering, with the power turned off. The work is "wet", and water or glue can get on the wires and short out. If the wiring is done in accordance with all the rules and there are circuit breakers, this is not scary. They just cut off the power and that's it.

If the wiring is still done in the old way, it can be dangerous. Worst of all, in this case it is often not possible to turn off the power supply in a separate room. Only in the whole apartment or, at best, in its half. Then the way out is to remove the power wires from the sockets and switches (when the power is off, of course) and carefully insulate the ends, then hiding them under the plugs. Then you have to unwind them and put them in place, but it will be safe this way.

Lighting during work is done temporarily - extension cords are pulled from other rooms and portable lamps are turned on. After you figured out the electricity, you can move on.

Filling irregularities

Here you first have to assess the condition of the walls. First you need to pull out all the nails, screws, remove chips and embroider cracks. Then look at the results. If the walls are more or less even, there are only small defects, you can get by with episodic alignment. Close up only cracks, dents, chips. They can be covered with finishing putty. Only before leveling the wall, finally clean it of dust and pieces of wallpaper, and then cover it with a primer (wall roller and brush in the corners).

If the wall is after “processing” with a puncher, you can’t do without a full-fledged putty of the entire wall. Mostly today, gypsum putty is used. First, a layer of primary or starting is applied. It is with a coarser grain and the layer can be up to 3-5 mm. With this composition, the main irregularities are leveled, trying to achieve a flat surface. After drying, they pass with a special mesh, removing bumps and sagging that may be.

After the finishing putty is used. It is very plastic and is applied in a thin layer - up to 1-2 mm. Here, after it, the wall becomes smooth (after the irregularities have been smoothed out with a grid, only with a smaller cell).

Wall primer

The second layer of primer is applied after puttying. It forms a film on the surface, which reduces the absorption of the adhesive, and also improves adhesion. For the case of wallpapering, a thinner wallpaper paste can be used as a primer. Each pack has a table that indicates the amount of water for gluing and primer. We dilute the glue in the right proportion, wait for it to be ready (also on the package) and cover the walls with the composition. The priming technique is the same: first go through the corners with a brush, then smooth surfaces with a roller.

In the video, the use of primary putty is for some reason called plaster, but otherwise the sequence of actions is correct.

Gluing rules

When pasting wallpaper, there are several rules that must be followed. The technique varies depending on the type of wallpaper, as does the glue, which is necessary for a quality result. the difference is mainly in when and where to apply the adhesive. You don't have to guess. Everything is on the insert, which is included on each roll of wallpaper. It is depicted in graphic form, and in some it is written which of the parts should be smeared with glue: only the wall or only the wallpaper, or maybe both at once.

But some things remain unchanged. For example, drawing a starting strip.

Where to start

In fact, the starting point is not so important. It is important that the first strip is glued strictly vertically. Therefore, the choice is yours.

If the room has a well-drawn corner: even and exactly vertical, you can start from it. You can start from the door with a perfectly exposed jamb. If there is nothing like that, draw yourself a landmark yourself. Take the building level, mark a point on the wall and draw an exactly vertical line through it. Inexpensive building levels of a household class, which we usually use in repairs, sometimes give a solid error. And since it is important for us to stick the first strip strictly vertically, check the accuracy of the line with a plumb line. Here he never lies, showing exactly down. If everything is fine, you will align the edge of the strip along this line.

If you still haven’t decided where to start gluing wallpaper and this is your first experience in this area, start with the wall that is less visible than others. For example, the one along which there is a closet. It will be difficult for you for a couple of first pages, and then you will better understand what's what and there will be fewer flaws.

How to glue wallpaper on the wall

If glue, at the request of the manufacturers, is applied to the cut piece, the smeared strip is folded so that the smeared side is inside. To do this, wrap the edges to the middle, then fold several more times. The folds are not pressed. Let them stay round. This is necessary so that all layers are saturated and the canvas fits well on the wall, and also sticks without bubbles.

If you want to apply glue to the wall, coat the area a little more than the width of the wallpaper. The area under the ceiling, in the corner and near the floor is smeared with a brush. Then the rules are general.

Take the cut off strip, climb the ladder. Bring the upper edge a few centimeters to the ceiling, then align one of the edges along the drawn “start” line. Since the wallpaper today is glued end-to-end, it does not matter which of the edges.

Strictly attaching the side edge to the line, moving from this line to the other edge, glue the wallpaper in the ceiling area. Then, gradually moving down, go down a little lower.

Extra centimeters on the ceiling are cut off. It is more convenient to do this with a paper knife and a large spatula. Press the paper well against the corner by swiping your hand. Then apply a spatula. Run a knife blade along its edge.

Cutting under the ceiling and near the plinth

When gluing the canvases, movements are made from the center of the strip to the side and slightly down, expelling the trapped air to the edges. Previously, this was done with a rag, but it turns out better and faster with a roller with an elastic nozzle (it is usually yellow). When working with it, there are practically no bubbles. But if the wallpaper is structural, with an extruded pattern, they can be crushed with a roller. Then take a wallpaper brush. It is wide and flat, with a hard pile.

Wallpaper brush for quick sticker

Having reached the place where the strip has not yet been glued, unfold the rest tightly and follow the same pattern. First, expose the edge, then use a roller or rag to expel the air, achieving a flat surface.

The second strip is glued in exactly the same way, with the only difference that the canvas already on the wall will serve as a guide for gluing the edge. That's why it's important to stick it evenly, otherwise everyone else will also mow.

Secrets of pasting corners

The most difficult thing is to properly glue the wallpaper in the corners. But that's only as long as you don't know the secret. At first, you can try to do it simply. Wrap one of the parts on the adjacent wall by 1-2 cm, and cut the second at the corner.

It's easy to do, and it looks good. But on some wallpapers, this strip is very visible. There is another way for this case. Glue the canvases on both sides of the corner so that they wrap at least a little on the other side (2-3 cm is enough). Press well so that they fit exactly. to the walls and corner.

Then take a special cutter or a large spatula. Press it in the corner, cut the wallpaper along its edge with a sharp knife. It is necessary to cut both sheets at the same time, so considerable effort may be required. To make the cut continuous, do not tear off the knife. Stopping, move the spatula, which rests on the blade, and then continue the cut.

Having cut off everything, remove both cut strips, and join the remaining canvases in the corner. If the wallpaper was well pressed before cutting, the match is perfect, without any discrepancies.

How to glue wallpaper on the outer corners? Pretty much the same way. In the first case, one of the strips is wrapped around the corner by one or two centimeters (for thicker wallpapers, 2 cm is better, for thin ones, 1 cm is enough). The second strip is glued strictly along the corner. If this overlap is visible (usually on non-woven wallpaper), it will be necessary to cut along the entire strip. In this case, wrap more and cut vertically with the same spatula and knife. Remove the cut off, glue the joint.

Meter wallpaper in the corners is glued in the same way as narrower ones. It happens that a narrow strip is needed in the corner, and the rest is cut off. If the wallpaper is without a pattern, it can be used somewhere, at least in a different corner. With patterned canvases, they can also sometimes be attached somewhere, but this is more difficult to do. That's why they take patterned ones with a decent margin: just for such cases.

How to glue vinyl wallpaper on a paper basis, how to expel non-ideal corners in this video.

How to glue wallpaper near the door and window

If the doors or window are flush with the plane of the wall, there is usually no problem. The wallpaper is cut along the door frame or along the edge of the trim. The canvas to the corner of the casing or frame is cut at an angle of about 45 °. The cut parts are wrapped along the opening, bent and then cut off with scissors or a knife. Smoother and faster is obtained using a knife and spatula.

How to glue near the door

More difficult is the option when it is necessary to paste over the slope of the door or window. When using paper wallpaper, the principle is again simple: we glue the strip on the slope, leading it 1 cm onto the wall. From above we glue a piece exactly along the cut of the window opening.

But with wallpaper on non-woven fabric, this method will not work: “leaks” are too visible. In this case, the strip is cut along the window opening with a small margin. Another fragment is glued on top with an overlap, cutting them exactly along the cut of the window opening. The glued piece is wrapped inside, on a slope. Then join as before.

It is difficult to explain in words. More accessible in video. In it, by the way, there is a plot about the design of wallpaper for arched openings.

How to make seams invisible

Care must be taken during gluing to ensure that the joints of the canvases are invisible. You need to connect the canvases so that there is no gap between them, but also so that they do not overlap one another even by a millimeter. A perfect match needs to be achieved.

Since we meet perfectly even walls, alas, infrequently, it turns out that the seam creeps a little, then diverges. Your task is to move the canvas so that it becomes perfect and invisible. You can move the canvases with your hands - they can slightly stretch and shrink. This is how you achieve the desired match. If the defect formed is too large and nothing can be achieved by shifts, the strip is peeled off to this point and, corrected as necessary, glued again. Sometimes, if the seam sticks out a little, rolling with a special tapered roller can help.

With this technique, it turns out that first the edge is glued, which is joined, and then, from it they begin to smooth the rest of the surface of the canvas. If you have examined the seam and are satisfied with the result, take a clean rag and wipe it from excess glue that could come out with all these actions.

For information on how to glue meter-long non-woven vinyl wallpaper and how to make the joint invisible, see the video.

We eliminate shortcomings

With a lack of experience, it may happen that after or during drying, bubbles appear on the walls. You can remove them with simple steps. Take a large syringe, draw glue into it, pierce the bubble and inject some glue into it. Vinyl wallpaper, acrylic, paper - the upper part is unimportant. Actions vary depending on the basis. If the wallpaper is paper-based, wait five to seven minutes, if it is non-woven, act immediately.

How to remove bubbles from wallpaper

Quite often the seams diverge. Wallpaper may lag along the flow or baseboard. There are two ways to glue them. Use a brush and leftover glue or buy a special one for seams. It comes in a tube and is applied pointwise. And again, the procedure depends on the base. Having wet the paper, we wait for a while, then we glue it, watching the coincidence of the edges.