How to make winter washer fluid yourself. Dilution of alcohol to produce anti-freeze windshield washer fluid

In the cold season, there are situations when the temperature drops rapidly below zero, and the windshield washer fluid has run out in the garage. In this case, you can quickly make a do-it-yourself anti-freeze for a car of any brand. Consider the most popular folk recipes preparation of the composition, their advantages and disadvantages.

Making a solution based on vodka

For non-freezing from vodka, it is paramount to use "fiery" from ethyl alcohol

One of the most basic options for providing yourself with windshield washer is a vodka solution. Any vodka (not "singed") based on ethyl alcohol is suitable. The hot drink does not freeze in frost down to the mercury column at -25ºC, and prepared and purified water is used as a supplement, which does not leave a divorce, does not contain solid impurities. In principle, vodka itself is suitable for pouring into a washer reservoir. When calculating for slight frosts, you can play with the proportions of water / alcohol by adding distillate to the container. If, for example, the contents of the bottle are diluted with water in a ratio of 40/60 (40 - vodka, 60 - water), then the obtained glass wash is able to successfully resist crystallization in the range from -5 to -10ºC.

An important addition is a dirt-soluble element or detergent, in other words. Suitable as a car shampoo for the body, and non-aggressive detergent compositions for dishes, fleecy coatings, as well as liquid soap. A teaspoon of the product will be enough for 1 liter of solution, otherwise, if you overdo it, foaming will reach a critical level, and the car will be covered with a layer on the go soap bubbles. Also, do not use strong chemical cleaners that are designed to flush engineering communications, waste pipes, heating systems, etc. Even automatic washing powder can cause an undesirable reaction on chrome moldings, rubber seals and car lacquer surfaces.

Advantages:

• vodka is available always and everywhere, often in kitchen stocks;
• the product is non-toxic, does not cause chemical burns.

Disadvantages:

• alcoholic beverage, subject to state excise taxes and relatively expensive glass containers, is not cheap;
• it is impossible to achieve a condition that endures severe frosts.

Video recipe for making anti-freeze from vodka

Do-it-yourself anti-freeze for a car from moonshine

The above recipe is not bad, but in the search for cheap vodka, you can run into dangerous "bodyagi" in their composition. In this case, many look more favorably towards home-brewed moonshine. It is noticeably cheaper than factory analogues, and in terms of strength it can significantly exceed the latter. Thus, from the same volume, almost twice as much finished product for the windshield washer can be obtained. In addition, pure moonshine will perfectly cope with wiping the "front" in severe frosts, leaving no streaks and efflorescence. True, this is true only in relation to high-quality moonshine.

Advantages:

• reasonable price, the possibility of manufacturing at home;
• it is possible to provide the washer fluid that does not freeze down to -40ºC.

Disadvantages:

• if the moonshine is of poor quality, then oily stains may appear on the glass, and the liquid itself will have a sharp unpleasant odor.

Ethanol winter glass wash: proportions, pouring into the heating system

Both vodka and moonshine as a windshield washer are valuable for their high content of ethyl alcohol, which can be freely bought at a pharmacy, store household chemicals practically in pure. The content of alcohol itself according to GOST is 96%, which allows you to do water mixtures different saturation:

• 1:9 - -5ºC;
• 1:4 - -10ºC;
• 1:2 - -23ºC;
• 1:1 - -35ºC etc.

Advantages:

• neutral smell, no toxic fumes;
• when using distilled water, there are no impurities;
• high cleaning performance;
• absence negative impact on paintwork, rubber, plastic, chrome;
• ethanol available in every pharmacy.

Disadvantages:

• pharmacy alcohol is expensive, which is why factories never use it to make antifreeze liquids.

In addition to washing glass, ethanol does a good job of heat dissipation in water heating systems. Unlike other alcohols, it is non-toxic and does not spoil rubber seals, aluminum parts. And most importantly, after a couple of frosty nights, the batteries will not meet the owner with breaks from frozen water.

Production of homemade antifreeze without ethyl alcohol

Methanol can be used instead of ethyl alcohol. It is much cheaper, but is very toxic. Just a glass of concentrate can cause fatal outcome, and inhalation of methyl alcohol vapors leads to severe intoxication, hallucinations, loss of consciousness. Therefore, if you work with methanol, then in a ventilated room, in a respirator. It is undesirable to get the composition on the skin. Otherwise, the work on the preparation of antifreeze is identical to the situation with ethanol - the base is diluted with distilled water with the addition detergent in a ratio of 1 to 9.

Advantages:

• cheap;
• effective in severe frost (if the appropriate alcohol concentration is selected).

Disadvantages:

• methanol is dangerous; if it seeps into the cabin, its vapors can intoxicate the driver;
• it may be difficult to find alcohol in the open sale (the product is banned in a number of countries).

Variant using isopropyl alcohol

Isopropanol looks like the "golden mean" in the world of alcohol-containing antifreezes - it is not as toxic as methanol, but not as expensive as ethyl alcohol. 2-propanol is widely used in the composition of solvents, paints and varnishes, which indicates its aggressive nature in relation to automotive varnishes and enamels. However, a moderate amount of isopropyl alcohol is considered quite acceptable as an active ingredient in factory glass washing. Mass production takes the approach of diluting alcohol 1 to 4 with water, adding detergent and fragrance to counteract the pungent smell of isopropanol. In order for the liquid not to crystallize at minus 35-40, the ratio of alcohol to water should be 1:1.

Advantages:

• you can easily buy in the department of household chemicals, order on the Internet;
• alcohol is not much more toxic than ethyl alcohol - health problems arise only with internal use;
• Isopropanol has long been considered the standard in winter glass washing.

Disadvantages:

• high concentration adversely affects the paintwork.

Cheap ice cream you can make at home

When not very severe frosts You can completely do without ethyl alcohol, and alcohols in general. For example, a 50/50 water-vinegar solution will allow you to confidently deal with frost and liquid dirt on the windshield at temperatures around -15ºC. But using a tandem in warmer weather is not recommended due to increased evaporation and the penetration of a pungent odor into the cabin. Another "homemade" recipe uses ammonia, which is carefully dissolved in water, based on a 1: 2 ratio.

Advantages:

• such funds do not pose a risk to human health;
• affordable price.

Disadvantages:

• both vinegar and ammonia have a sharp, unpleasant odor;
• the aggressiveness of the products in relation to paint, chrome should be taken into account.

Household glass cleaner

Another way to obtain a safe mixture for cleaning auto glass in cold weather involves the use of household alcohol-based window cleaner at home. These products include ammonia which dissolves well. body fat and resists frost. But the effectiveness of "Mr. Muscle" against the background of automotive realities is low, so it is better not to dissolve it with more than two parts of water. But the cleaning effect in this case will be provided.

Advantages:

• cleans glass well;
• the manufacturer usually adds flavor;
• the product is non-toxic.

Disadvantages:

• not suitable for severe frosts.
• If there is a washer reservoir heating

In the case of using a washer fluid heating system on a car, there is not much point in messing around with acids and alcohols. It is enough just to buy a quality dishwashing detergent and dilute it with distilled water in the ratio of one glass (50 ml) per three-liter jar. Cheap and cheerful: factory additives will prevent water from turning into a block of ice, and heating the tank will ensure liquid state solution with high cleaning performance.

• news
• Workshop

It will be possible to pay for parking in Moscow with a Troika card

Plastic cards"Troika" used for payment public transport, will receive a useful feature for motorists this summer. With their help, it will be possible to pay for parking in the zone paid parking. To do this, parking meters are equipped with a special module for communication with the transport transaction processing center of the Moscow Metro. The system will be able to check if there are enough funds on the balance...

Limousine for the President: more details revealed

The site of the Federal Patent Service continues to be the only open source of information about the "car for the president." First, NAMI patented industrial models of two cars - a limousine and a crossover, which are part of the Cortege project. Then, the namishniks registered an industrial design called “Car Dashboard” (most likely, it was ...

Photo of the Day: Giant Duck Vs Drivers

The path to motorists on one of the local highways was blocked by ... a huge rubber duck! Photos of the duck instantly went viral on social networks, where they found a lot of fans. According to The Daily Mail, the giant rubber duck belonged to one of the local car dealers. Apparently, he demolished an inflatable figure on the road ...

Run Magadan-Lisbon: there is a world record

They traveled across Eurasia from Magadan to Lisbon in 6 days 9 hours 38 minutes and 12 seconds. This race was organized not only for the sake of minutes and seconds. He carried a cultural, charitable and even, one might say, scientific mission. Firstly, 10 eurocents from each kilometer traveled was transferred to the benefit of the organization...

Datsun cars have become more expensive immediately by 30 thousand rubles

Immediately, we note that the rise in price did not affect the cars assembled last year. Last year's on-DO sedan and mi-DO hatchback in basic versions are still offered for 406 and 462 thousand rubles, respectively. As for cars manufactured in 2016, now you can’t buy on-DO for less than 436 thousand rubles, and now dealers are asking for 492 thousand for mi-DO ...

New measure: drivers allowed to chip in for road repairs

The corresponding bill was approved by the deputies of the regional legislature, RBC reports. Both individuals and legal entities. Citizens and companies will be able to make "voluntary donations", which will be used to "financial support for road activities." "After...

Demand for Maybachs has risen sharply in Russia

Sales of new luxury cars continue to grow in Russia. According to the results of a study conducted by the AUTOSTAT agency, following the results of seven months of 2016, the market for such cars amounted to 787 units, which is immediately 22.6% more than in the same period last year (642 units). The leader of this market is the Mercedes-Maybach S-Class: this...

Mercedes will release mini-Gelendevagen: new details

The new model, designed to become an alternative to the elegant Mercedes-Benz GLA, will get a brutal appearance in the style of Gelendevagen - the Mercedes-Benz G-class. The German publication Auto Bild managed to find out new details about this model. So, according to insider information, the Mercedes-Benz GLB will have an angular design. On the other hand, complete...

Moscow carsharing was at the center of the scandal

As one of the members of the Blue Buckets community, who used the services of Delimobil, said, in the event of an accident involving a rented car, the company requires users to compensate for the cost of repairs and additionally charges a fine. In addition, service cars are not insured under comprehensive insurance. In turn, representatives of Delimobil on the official Facebook page gave official...

The iconic Toyota SUV will sink into oblivion

The complete cessation of production of the car, which has so far been produced for the markets of Australia and the Middle East, is scheduled for August 2016, according to Motoring. For the first time serial Toyota FJ Cruiser was shown in 2005 at the New York International Auto Show. From the start of sales until today, the car was equipped with a four-liter gasoline ...

The cheapest car in the world - TOP-52018-2019

Crises and the financial situation are not very conducive to buying a new car, especially in 2017. Only everyone has to drive, and not everyone is ready to buy a car in the secondary market. There are individual reasons for this - to whom the origin does not allow to travel ...

HOW to order a car from Germany, how to order a car from Germany.

How to order a car from Germany There are two options for buying a used German car. The first option involves an independent trip to Germany, selection, purchase and transfer. But this method is not suitable for everyone due to lack of experience, knowledge, time or desire. Exit - order a car ...

A clean windshield that does not obstruct control of the situation on the road is one of the main conditions for safe driving. In the summer, ordinary water can be used to keep the windshield clean, but in the cold season you can’t pour it into the water - it can freeze and disable the entire washer system.

In winter, when the air temperature drops below zero, drivers use a special anti-freeze liquid as a detergent, in a simple way - anti-freeze. The cost of store-bought anti-freeze is quite large, and given that this product is consumed quickly, the constant purchase of store-bought liquid hits the pocket quite hard.

From this article, you will learn how to make a do-it-yourself anti-freeze at home, consider recipes with and without alcohol content. In this case, the resulting liquid will not be inferior to a store-bought product, neither in terms of the efficiency of cleaning contaminants, nor in terms of heat resistance.

STUDYING THE COMPOSITION OF INDUSTRIAL WASHERS

In order to make a washer fluid on your own, you first need to understand the composition of industrial designs and take into account their advantages and disadvantages.

All commercially manufactured automotive detergents are usually alcohol-based. There are three types of alcohol that are added to the composition of such products:

• Methyl. The use of methyl alcohol in the manufacture of automotive and household chemicals is prohibited by the laws of most countries, including Russia, but this does not prevent unscrupulous manufacturers from adding it to their products without appropriate instructions on the packaging.

Despite its low cost, methyl alcohol is an extremely toxic substance, the inhalation of whose vapors in in large numbers causes serious harm to health.

• Isopropyl alcohol is the most commonly used option due to the low cost of raw materials. Negative influence on the body does not possess, but at a high concentration in the composition of the washer, it can damage the varnish layer of the car. Antifreeze based on isopropyl alcohol has a sharp, unpleasant odor reminiscent of acetone;
• Ethanol - the best way in terms of the final characteristics of the washing agent. It is non-toxic, does not have a pungent odor, but is expensive, which is why it is extremely rare in anti-freeze compositions.

Saving money that is detrimental to health or the car is not in our interests, so we will use ethyl alcohol to make the washer fluid.

For those who doubt whether the game is worth the candle, let's say that do-it-yourself frosting based on ethyl alcohol in any case will cost us less than store remedy with a low-quality composition, the bulk of the cost of which is the manufacturer's cheat.

WE DO NON-FREEZE WITH OWN HANDS

To make an anti-freeze at home, we need the following components:

• Ethyl alcohol - you can buy at a pharmacy or order on the Internet;
• Water - any recipe for a home-made antifreeze involves the use of distilled water, since the tap fluid may contain rust and the smallest mechanical impurities that are invisible to the eye, but adversely affect the condition of the windshield;
• Store-bought dishwashing detergent (Gala, Fairy and the like) - required for effective removal of contaminants.

The proportions in the antifreeze of water and alcohol depend on at what temperature regime means will be used:

• Air temperature up to -5 ° C - alcohol concentration of the total volume of washer fluid - 11.3%;
• -10.6 °C - 20.3%;
• -12.2 °C - 22.1%;
• -16 °C - 26.7%;
• -23.6 °C - 33.8%;
• -33.9 ° C - 46.3;
• -41 °C - 56.1%;
• 51.3 ° C - 71.9%;

For example, if you are making anti-freeze for use at 16 degrees below zero, for 3 liters of product you will need to use 801 grams of alcohol and 2199 grams of water. Detergent is added at the rate of 1 tablespoon per 3 liters of the mixture.

Everything is done extremely simply - add all the components to a container of suitable volume (the same five-liter bottle of water will do) and mix.

Do not forget about safety measures: antifreeze should not get on the mucous membranes of the body, and it should be stored away from children.

ALTERNATIVE RECIPES FOR FREEZING (WITHOUT ALCOHOL)

1. Do-it-yourself anti-freeze without alcohol - to prepare it, mix a store-bought window cleaner and distilled water in a ratio of 1: 2. One of the most economical recipes, since window cleaner has good heat resistance and is much cheaper than medical alcohol;
2. How to make a vinegar-based anti-freeze: distilled water is mixed with vinegar in a 1: 1 ratio. It makes sense to use this mixture only when severe frosts occur, since at temperatures below -10 degrees it stinks the entire interior with an unpleasant smell of vinegar, which is not interrupted even by adding flavorings to the composition of the mixture;
3. Antifreeze based on ammonia solution: such a mixture should contain 35% ammonia and 65% distilled water. When using the mixture in severe frosts (below -20), it makes sense to add 150 grams of vinegar to its composition;
4. For small mixtures without alcohol, which only contains dish detergent and distilled water. Mixing proportions - 100 grams of detergent per 5 liters of water. It is important to use high-quality detergent here, since heat resistance is achieved precisely due to this component.

To check the quality of the resulting product, it is enough to put the bottle with the mixture in the cold and keep it there for a day. If, during your stay on the street, the anti-freeze has not changed its consistency to a thicker one, and no ice crystals have formed in it, then everything turned out fine and the product can be poured into the washer reservoir.

Timely cleaning of the windshield from dust and dirt is a factor that determines the safety and efficiency of maneuvering. In summer, water can be poured into the washer reservoir, but when it comes winter period, required special formulations- non-freezing. This washer does not freeze when sub-zero temperatures, which eliminates the possibility of damage to the tank, hoses, and other components.

If you need to constantly purchase high-quality washer fluid, considerable expenses are expected. But there is a way out - do-it-yourself anti-freeze for cars. It does not take much time to make such a liquid, all the ingredients are available.

The desire to independently produce an antifreeze liquid may arise not only because of the cost of the product. Often there is a low quality of compositions that begin to freeze at more high temperatures. Unscrupulous manufacturers can use prohibited bases, the fumes of which harm the driver, passengers, the environment, and even the surface of the car.

When thinking about how to make an anti-freeze at home, you need to prepare materials and do not forget about safety precautions. All manipulations should be carried out with gloves.

Often, a base in the form of alcohol or alcohol-containing substances is used for the washer.

Here you can use:

• isopropyl alcohol - the most popular base, characterized by optimal cost, safety (it is actively used in the production of antifreeze);
• ethyl - the most expensive option, this alcohol is used in medicine (the choice of such a base is not economically feasible);
• methyl alcohols are the most affordable, but they should not be used, since evaporation products can harm a person.

To do the work yourself, you need to prepare:

• plastic bottle;
• measured capacity;
• gloves;
• basis;
• water is needed.

Depending on the chosen recipe, you may additionally need:

• powder, dishwashing detergent;
• perfume to improve the smell;
• blue, dye;

Doing all the work, do not forget about safety.

The recipe for preparing the composition based on isopropyl alcohol is very simple. It is necessary to take the alcohol itself, water and detergent, mixing them in the optimal proportion.

Main stages of work:

1. A plastic bottle or a suitable canister is being prepared. 2 liters of water are poured into it, preferably distilled.
2. The next step is to add isopropyl alcohol in the same volume (2 liters). The resulting liquid is able to work effectively at temperatures up to -21 -23 degrees. If you need to increase frost resistance, increase the amount of alcohol in the washer. For example, with a content of only 35% water, the anti-freeze will retain beneficial features and at -29.
3. Addendum detergent composition will improve product performance. One cap is enough for a whole bottle. You should not overdo it, otherwise foaming will increase, which will affect the quality of the system - the glass will be worse cleaned.
4. The final stage - all components must be thoroughly shaken, mixed.

At right approach the production of the product will not take much time. Studying the composition of the antifreeze for cars and the proportions of the components, it is worth noting that the quality of the constituent products also matters.

Attention:

The use of ordinary water for the preparation of a washer is dangerous due to the formation of plaque, the appearance of traces of rust. This causes damage to the tank, nozzles, and other components of the system (if there is no distilled water, you can take regular water, but it must be passed through household filter and let stand). The detergent must be of high quality, the presence of chlorine is not allowed.

Also, other ways are popular among car owners on how to make an anti-freeze yourself. Just choose the right recipe and get to work.

What can be used to prepare a washer:

1. Window cleaner. This product usually contains alcohol. Therefore, preparation involves the addition of one part of the product and two parts of water (preferably distilled).
2. Dishwashing liquid. This product is also suitable for work, but you only need to choose quality formulations proven brands, because this determines the final characteristics. For 3.25 liters of water, add a spoonful of concentrate.
3. Vinegar is used as a raw material. For getting working fluid you need to combine vinegar and water. Take the same proportions of the components. We must not forget that such a product is designed to work in severe frosts, from -10. With more high rates the whole car will be filled with a sharp unpleasant smell.
4. Using ammonia, it is enough to take one part by adding 3 parts of water, but the composition must be mixed carefully so that foam does not form. The option is not suitable for severe frosts, but you can improve the performance and frost resistance by adding 50–100 grams of vinegar.
5. Ethanol, the same medical, ethyl alcohol, is rarely used due to more high price. The proportions depend on the characteristics of the base - when choosing 70% alcohol, you need to take 750 grams of the product and add 10 300-gram glasses of water. If there is alcohol 96.6%, take 650 grams. After mixing the ingredients, add a spoonful of powder (with active use in the car, a clear smell of alcohol may be felt).
6. Methanol is a dangerous and prohibited substance because it has no smell and is not felt at high concentration. It is not worth working with such a basis on your own. And yet, to obtain antifreeze, a part of methanol is mixed and 9 times more water, adding dyes, a spoonful of dishwashing detergent.

Having studied the recipes and proportions, every motorist will understand how to make an anti-freeze yourself quickly and efficiently without harm to health.

How to check washer fluid?

Without a preliminary check, you should not pour the solution into the system. It is easy to make sure of the quality of the prepared composition - you need to pour it into a container and leave it in the cold. If after a few hours the initial characteristics have not changed, you can safely use anti-freeze.

Sometimes the liquid becomes gel-like, freezes, which means you need to add more isopropanol.

When buying a composition for cleaning car glass, I want to choose a quality product. But, as before, there are counterfeit formulations made on the basis of methanol. With a large amount of vapors of the substance, the driver and passengers feel nausea, dizziness.

But how to determine methanol in anti-freeze?

Checking methods:

1. Have to take copper wire. Using a lighter, it is heated and lowered into a liquid. If it contains methanol, it will smell like vinegar.
2. Soda - its addition to products with methanol is accompanied by complete dissolution. Whereas in other cases, soda precipitates.
3. The smell is also different. Isopropyl has a pungent odor when containing methanol unpleasant odors no.

When using non-freezing liquid, it is necessary to ensure proper storage conditions, excluding access for animals and children.

Windshield washer fluid is essential to keep your car in good condition. Most store-bought windshield wipers contain methanol, a toxic chemical that is hazardous to health even when small quantities. Because methanol is so unhealthy and environment, some car enthusiasts prefer to personally make windshield washer fluid at home, in which there will be not a drop of methanol. Such a liquid can be quite simply made from household goods, especially since in the long run they will also help save a lot.

Steps

Wiper solution

Take a clean empty container and pour 4 liters of water into it. The container should be easy to fill and hold at least five liters of liquid. Always use distilled water to prevent mineral buildup in the nozzles and pump.

• As a last resort, you can use tap water. Most importantly, do not forget to replace the fluid as soon as possible so as not to harm your car.

1. Add 250 ml glass cleaner. Take any store-bought glass cleaner of your choice. The main thing is that he gives as little as possible soap suds and did not create streaks (preferably none at all). This method suitable for everyday use, especially in summer.

   Shake the container to mix the liquid well, then apply it to the windshield. If this is your first time preparing such a washer fluid, first test it on your car. Take a rag, soak it a little in the liquid and wipe the corner of the windshield. Ideally, the cleaner should remove the dirt without leaving any residue behind.

   Add 125 ml of ammonia. Take non-foaming ammonia, which is free of additives and surfactants. At this stage, you should be very careful, as concentrated ammonia can be dangerous. Work in a well-ventilated area and wear gloves. When ammonia is diluted in water, it becomes relatively safe and can be used as a glass cleaner.

How to make a non-freeze with your own hands? Just

Do-it-yourself anti-freeze at home

In winter, pouring water into the washer reservoir can be not only useless, but also unsafe. This can damage not only the tank itself, but also flexible hoses water supply, and pump. But the worst thing is that you will lose a full view at the most inopportune moment, and this can end in failure.

Buying washer fluid in the store, of course, will solve this issue without any extra effort. If you travel once or twice during the winter, then this option is for you. But if your car is operated very actively, in winter, then do-it-yourself anti-freeze is for you.. In doing so, you can save a lot. Below will be described how to make an anti-freeze at home.

Get liquid enough good quality quite easy. You just need to purchase your favorite factory version in a car dealership and study the composition. Next, it remains to put together necessary ingredients and mix them together. But in reality, everything is not so simple: the composition indicated on the packaging may, to put it mildly, be different, and not all components are available at retail. How to make a non-freeze with your own hands is simple, and from the available components, you will now learn.

Winter washer fluids of this type are divided according to the type of alcohol contained in them:

1. Based on methyl alcohol. This category is prohibited by law, as it has increased toxicity and, as a result, is very dangerous to health. But, despite all this, it is often used by unscrupulous manufacturers due to the cheapness of the main raw materials;
2. Using ethyl. It is also the raw material for the production of the "famous" drink. The manufacture of non-freezes from it is the most expensive and therefore not common;
3. Made with isopropyl alcohol. The most common component used in the production of goods of this class. It has a strong odor similar to acetone. It has a negative effect on the human body only when ingested. Bad effect on the coverage of the car.

So we smoothly approached the question of how to make an anti-freeze.

Based on all the positive and negative qualities considered liquids, we will not risk our health and the health of our passengers (children may be among them). And we will make our glass cleaner from ethyl alcohol, familiar to everyone. I can upset lovers of savings - it will not be the most cheap option. For this we need:

• Ethyl alcohol used in medicine. It can be bought in online stores with delivery right to the door of the house. And it is sold in various volumes, from small to twenty-liter canisters.
• Water. Better distilled, but if one is not available, you can use water passed through an ordinary filter.
• Any detergent, for example, the one that is used to wash dishes. There are no restrictions here, you can use what is available.
• Well, you can use a flavoring agent to add flavor.

Mix water and ethyl alcohol in percentage required to obtain a non-freezing liquid to the temperature you need:

After mixing, add detergent at the rate of one tablespoon per three liter can of mixture and perfume it all with perfume.

A few more recipes

All other recipes will be of interest to those who like to save money. Antifreeze based on methanol.

Be careful methanol is a strong poison. Therefore, when working with it, one must be careful, and under no circumstances should it enter the respiratory tract and eyes.

This recipe requires nine parts water and one part methanol. Also, everything is mixed and soap with fragrance is added.

Cooking with isopropyl alcohol. We fill twenty percent of the container with isopropyl alcohol, fill the rest with water, and forget about the fragrance and soap.

You can also use any alcohol-based window cleaner. We dilute it at the rate of: two parts of water and one part of the product and our mixture is ready for use.

How to make anti-freeze at home

Antifreeze without alcohol

Some may be interested in the question: is it possible to do a non-freeze with your own hands without alcohol? Yes it is possible. There are recipes without alcohol.

Do-it-yourself anti-freeze without alcohol

Do you have dishwashing liquid at home? Let's put him to work! It will take three liter jar one tablespoon of water, mix, ready! But be aware that the quality of your mixture directly depends on the quality of the detergent used. Therefore, before “experiments”, check whether the planned use of soap will freeze (put it in the freezer or on the balcony).

You can use vinegar. But do not forget - it can only be used from minus ten degrees. Otherwise, there will be a terrible smell in the car interior. To make this washer, you need to mix water and vinegar in equal proportions.

Manufactured using ammonia. For this recipe, you need to mix three parts of water and one part of ammonia. Be careful not to foam while mixing. The resulting mixture is not recommended for use at very low temperatures.

Try to use distilled water for cooking . "For guaranteed result check the prepared or purchased liquid. To do this, put a small amount in freezer with a temperature slightly higher than that planned for the operation of the vehicle. If it is not frozen, you can safely pour it into your car.