Simple phone stand. All options for creating a stand for a smartphone from a plastic card

The mobile phone has become an indispensable attribute of modern man. And on the road, and at home, and on the desktop, a useful gadget is given the main place, otherwise “suddenly someone calls, but I don’t hear / see.” For convenient placement of a cell phone on the table, coasters were invented. You can buy them in the store, or you can do it yourself from improvised materials. Even the most useless at first glance "unnecessary garbage", like a cardboard package from dairy products or a long-used cover for a disc, will come in handy in the work.

Cardboard stand

The first option is to make a cardboard stand for a mobile phone. This is not necessarily a single piece of material; you can take a used milk bag of a small volume (0.5 ml). It does not require anything to glue: you only need scissors.

The box must be thoroughly washed, crushed and cut off the bottom. Then cut along the folds.

The work will need a central part in the form of two rectangles. Between them is a fold. It must be cut out and folded with the outside inward, clamping the fold with one hand.

Starting from the opposite end, from below, you need to cut out a figure resembling the letter "T". It is narrowed upward, but has a beveled corner.

When the shape is expanded, the bottom edges become where the phone sits. It rests on the central edge. Budget stand is ready!

Stand from the cover for the disc

Surely everyone has a couple of DVDs lying around in the house. One of the unnecessary covers can be turned into a stand for a mobile phone.

To do this, the cover must be cut in half. Then cut off all the holes and rivets so that only an even rectangle with two bent corners at the ends remains.

The plate must be clamped with tweezers or pliers and lowered into boiling water. Thus, the plastic will become soft and pliable.

Holding the plate with pliers or any other tool, it must be bent so that one of the corner-ends does not slightly reach the other. 2-3 cm is enough, and the phone will be located in this space. One of the corners is glued to the surface. It turned out to be an interesting and light stand. The device can be placed on it both vertically and horizontally!

Paper clip stand

A paperclip mobile phone stand is an interesting thing that can be done in 2 minutes. To do this, you need a large massive paper clip, which you just need to unbend correctly!

To begin with, the wire is completely straightened into a line. Then you need to clamp it and bend it again:

1. Bend in the shape of a checkmark - U.
2. Bend both ends at an angle of 90 ° C, starting approximately in the middle.
3. Slightly bend the horses of each end.

Thus, an ordinary paper clip turned into a concise stand. The phone lies on it horizontally.

Toilet paper roll stand

Such good as a sleeve from a used toilet paper roll is enough in every home! Do not rush to throw away the cardboard form - it can be turned into a mobile stand in a matter of minutes.

All that is required is to properly cut off part of the sleeve at an angle. A small piece of cardboard should remain in front to create an emphasis. Such a stand will not be able to accommodate a phone that is too tall, but the standard size will “sit down” perfectly.

If desired, the stand can be decorated: painted, wrapped with cloth or pasted over with paper for gifts. And no one will believe that it was once part of a toilet roll.

Conclusion:

When working with familiar things, it is important to give free rein to imagination: try on, think, experiment. Then mobile phone stands will appear in the house regularly - and always different and interesting!

It doesn’t matter for what reason you need a smartphone stand, if there is no factory accessory, then there is always the opportunity to quickly make an analog from improvised means. And often we are not talking about disposable coasters, but about those that can be used for a long time.

Stationery clips

Stationery clips or binders will help you quickly and easily build a stand for your smartphone. It is enough to supplement them with any plastic or even paper card and the mount for the gadget is ready. You can build a more complex structure from binders alone - as you wish.

Paper or cardboard

If you recall the traditional Japanese art of origami or google a homemade paper stand scheme on the Internet, then you can literally build a smartphone mount with your bare hands using scissors and more or less thick paper or cardboard.

Wine corks

With a few wine corks, a small amount of glue, a knife, and free time, you can make a smartphone stand in just a few minutes. Get a pretty stylish accessory.

Toilet paper roll

A cardboard tube from toilet paper with a couple of knife movements turns into a quite wealthy stand for a smartphone. And if you add a couple more plastic cups, you get a completely portable speaker.

paper clips

If there are no binder clips on hand, but there are at least a couple of large paper clips, then they will fit. With a couple of movements, they can be turned into stands suitable for holding a smartphone.

A plastic card

When a nosebleed needs a stand, and there is nothing at hand but plastic cards, then they can be turned into a holder for a smartphone. It is better, of course, to use unnecessary discount cards or, at worst, gift certificates for this, and leave bank cards as a last resort, because after completion it is unlikely that they will be used for their main purpose.

Lego constructor

With enough bricks and a rich imagination, it's easy to assemble a real multifunctional docking station. What's good is that it's just as easy to turn it back into a constructor. And this is perhaps the most versatile way to create a DIY smartphone stand.

Cassette case

These days, it's easier to find a Lego set than an audio cassette case, but if you have one on hand, then the stand is actually ready. You don’t even need to modify anything - just take out the cassette and unfold its case to install your smartphone.

Pencils and erasers

In an office where there are a lot of pencils and rubber bands, but there is not a single stand for a smartphone, one can be made from what is. You just need to tie a few pencils with rubber bands into racks and fasten them together with the same rubber bands.

Roll of tape

Probably the most obvious and simple option for a handy gadget stand. It is enough just to lean the smartphone on a roll of adhesive tape or put the smartphone inside and thereby free your hands. You don't even have to modify anything.

It is logical that the 10 methods presented above do not exhaust the options for creating stands for smartphones. Almost everything that is at hand can become a holder for a gadget, if you show imagination.

Mobile communication devices are in every home, they have become almost indispensable for a modern person and perform a lot of functions. Therefore, quite often they need to be kept not in your pocket, but on your desktop, so a smartphone stand is a necessary thing for everyone. There are many ways to make a phone stand, but one of the best options is of course wood, as it, despite its hardness, will not scratch the smartphone and will look good both in the office and at home on the table.

The easiest way to make a wooden phone stand with your own hands is to simply make it from a regular plank. The design of such a product is as simple as possible - a groove of the required width is made in the board and the stand is ready. Since the board has a large plane, and after you put the mobile into the slot, it will stand firmly and securely on the table.

The most important thing about this wooden phone stand is the area of ​​the base that will be in contact with the table, it must be large enough to handle the functional load. As a base, such a homemade phone stand can have any wood and can be shaped into any shape. And the manufacturing process itself is limited to the fact that a groove is simply made in the plank with the help of a milling cutter. The groove can be made flat or sloped, depending on the angle at which the device should stand.

When you make a stand for a smartphone with your own hands, it is important to sand it well, especially in the groove area where the mobile will stand. After all, if there are irregularities, then you can scratch the glass, and this will spoil the appearance of your gadget.

Complex design

If you want your mobile device to be always in sight, not lost in documents, and at the same time your table looks beautiful, solid, then the stand should be appropriate. To do this, you can make it not just from a plank, but from several parts. Don't worry, it doesn't require a lot of tools or material either. The most important thing is not to rush and carefully consider the design that your homemade product will have.

A good do-it-yourself smartphone stand, which is suitable not only for any phone, but also for a tablet, and at the same time will be as stable as possible, can be made from two small boards.

The design of such a stand is as simple as possible, two identical rectangular wooden blanks are taken. On the one hand, about a quarter from the edge, a slot is made to the middle of the board. It is important that the slot does not run at a right angle, but obliquely, so that the stand is more stable and has the correct slope of the plane that will support the phone. On both blanks, a slot is made up to half the width of the blank.

For someone who is just starting out, it can be problematic to find the right angle for the slot. But this is not difficult to do, just attach two parts to one another at the planned angle and just make marks on the side of the end. Well, in addition, so that the phone does not slip, you need to make a groove on a horizontal plank, or stick a small bar that will be a stopper.

After all the cuts are ready, it is enough just to sand the stand well so that the bumps do not scratch the phone case, and cover it with tinting or just varnish.

There are many ways to make a stand for a phone of this design, for example, you can make a curly vertical part of the stand, which will greatly improve its appearance. Forms can be a variety of hand, leaf, animals, and in general everything that you think of, since a tree can be given almost any shape.

How to choose a stand design

There are quite a few ways to make a smartphone stand, but wood options are not only durable, but also beautiful. In addition, they look much nobler than other materials, as a properly selected wooden accessory will decorate any design, regardless of its style.

Therefore, in order for your handmade mobile phone stand to be beautiful and original, try to choose the right design, size and color. Of course, you should not forget about such parameters as functionality and stability, since if a cell phone falls, it can simply be damaged.

You can make a variety of phone accessories at home and you don’t need a special tool for this. In most cases, with due diligence and patience, you can get by with a simple hacksaw, chisel, sandpaper and a piece of plywood. Then just glue your sample from small parts and at home it will also be easy.

Do not be afraid to experiment and fantasize so that the stand you made is unique, and not like everyone else. After all, mass production is organized in such a way that anyone can afford to buy beautiful and seemingly diverse things. But truly bright individuals prefer unique things in a single copy. Such things are not sold in stores, they can only be ordered or made independently. The second option is much better, not only in terms of economy, but also in terms of the manifestation of individuality.

Even if you do not have experience in making any wood crafts, do not be upset, as there is nothing difficult in this. It is enough to carefully plan everything, calculate what tools and materials will be needed, and only after that proceed to the work itself. If something doesn’t work out for you, then you can try again, rarely does anyone manage to do everything right the first time, everyone learns and everyone makes mistakes. But this is the only way to gain experience and learn to do things right.

When there are cute cozy little things in the house, it helps to create an atmosphere of warmth. Making something interesting and useful at the same time is not so difficult. Today, almost everyone has a mobile phone. When we return home, we most often put it on the table. It happens that we do not notice and throw paper or other things on top, and sometimes we completely lose it on the desktop. A do-it-yourself phone stand solves two problems at once: you can always make room for your phone and design it yourself.

How to make a phone stand?

Surely you have at least one cardboard box at home. From such junk material you can create something unique. We suggest making a phone stand out of paper and an old box.

1. For work, you need to prepare stationery glue, a pencil with a ruler, a knife.

2. Before you make a phone stand, you need to prepare the cardboard. We cut rectangles measuring 10x20cm. We need 9 of these blanks.

3. Now you need to glue them three by one.

4. On two we draw such a detail. This will be the sidewall of the do-it-yourself phone stand.

5. Cut out. In order for everything to be beautiful and the structure not to lose its stability, you need to lay the sidewalls one on top of the other and check how much they are the same.

6. We take a clerical knife and cut a hole in the form of a rectangle.

7. Next, you need to make the base for the stand for the phone with your own hands. We measure the width of the phone and cut out the stand from the third blank according to the size. The phone's width is the length of our rectangle. The width of the rectangle should be such that it can fit into the grooves on the sidewalls.

8. We assemble the structure. You will also need a small circle of cardboard, its diameter is slightly smaller than the distance between the sidewalls. (photo 8)

9. All blanks must be pasted over with paper. It can be newspaper clipping or scrapbooking paper.
10. To make the back, take two pencils or something similar. We make holes in the sidewalls and insert them there. On the axis we put our circle of cardboard.
11. Do-it-yourself mobile stand is ready!

Another do-it-yourself phone stand option

You can make a simpler version of such a cardboard stand.

With a phone holder, you will not spend a lot of time looking for a mobile device. It will also be well protected. It is less likely that someone will drop it, step on it or spill tea, and most importantly, while driving a car, you will not be distracted. For aesthetic reasons, it can be an excellent decor for the interior of a car.

The simplest holder is a handlebar design with silicone loops. The adjustable bracket on the panel, into which the gadget is inserted, is characterized by the fact that it is compact and the phone is easy to install. Another very simple holder is a ball on a magnet.

Designer coasters are made of various materials, have different shapes - it all depends on the creativity of the master. For example, there is a lawn on a plastic stand, and a phone holder at the bottom.

The gadget holder can be made as an elegant wooden stand. For example, in the form of a tree with a hollow or improvised stumps. A neat wooden stand with randomly arranged slots where a mobile phone is inserted will look original.

A wooden stand can be very concise and resemble a photo frame where a smartphone is inserted. A wooden organizer on the panel can have not only a cell for a gadget, but also for pens and watches. A wooden stand in the form of a figurine supporting the phone looks original, only it needs to be well fixed.

Sometimes phone holders in the absence of a gadget are a nice souvenir. For example, a gadget stand in the form of a rotary phone looks original, showing the connection of times. Or look unexpectedly creative when the holder is an alarm clock into which a mobile phone is inserted.

Conceptually, the holder looks like a marble figurine holding a gadget in its hands. Even in winter, a shell stand will evoke memories of the sea. The stand can look like your favorite food, like sushi, a hamburger, or a caviar sandwich. In such souvenirs, the craziest fantasy can turn into reality.

The highlight of the holder in the style of minimalism will be the original mount. For example, on the principle of a table lamp attached to a clothespin to the table. Even an ordinary stationery binder will look original in the form of a phone holder.

It is worth looking at things with different eyes and arrange a cozy soft pillow or chair for the phone. If a woman is driving, it can be a fluffy basket, an original fabric pocket, a soft envelope on a pretty hinged loop. Knitted animals in the form of a coaster will always help to keep a good mood. Stylish bright accessories will not only serve you by performing certain functions, but will also help you think positively.

The holders can have a flexible cord for fastening, a suction cup, an adjustable bracket.

In choosing a stand for the phone, everyone is guided by their taste preferences. In terms of functionality, the holder must have a good fit so that the phone is secure.

How to DIY

From paper clip

A device that supports the phone can be made by hand. Such a stand will definitely be exclusive.

Homemade holders can be of three types:

• spoiling the salon;
• not distinguished by strength;
• representing a whole work of art that requires real skill.

We take the binder, remove the staples, bend them so that a holder is formed, wrap them with a thread and put them in their original place, securing them with an ordinary rubber band. It remains to attach a simple device to the duct. The phone is secure. The only negative is that the phone cannot be quickly removed from the holder.

From wire

In order to fix the phone on the wire holder, you will have to sacrifice the integrity of the front panel of the cabin, since holes will need to be drilled on it. The holder is made of strong wire, bending it in an appropriate way and inserting it into the holes. The phone must be firmly attached to the holder.

Aluminum column

It will take a little effort to make a stand out of aluminum. In any hardware store, you can inexpensively purchase connecting tubes with angles of 45 and 90 degrees, as well as an aluminum pipe with a diameter of 47 mm. You will need more ice cream sticks, an old phone case.

You can start creating the holder after the place where it will be located is determined. Now the necessary measurements are made. The pipe is cut into three parts. The short part is attached to a 45 degree angled tube. The horizontal part is held in 45 and 90 degree angle tubes. The longest part - a vertical pipe, 10 - 13 cm long, will hold the rack.

For greater strength, all fasteners are first lubricated with glue. A couple of cuts should be made in the case into which the ties are inserted. The cuts are on the tube. A long pipe is pulled together with ties. Wooden sticks are glued between the aluminum pipe and the case. The final step is to attach the connecting tube to the car.