Taps in the kitchen and bathroom are constantly in contact with water. As a result, salt deposits form on them, that is, limescale. It deprives the taps of their original cleanliness and shine. White stains appear both outside and inside plumbing. Over time, the crane may completely stop turning due to plaque. In order not to bring the plumbing to such a state, it is necessary to regularly clean it. There are many methods for removing limescale using improvised means. So cleaning the faucet at home is not difficult.
In almost any home, the quality of piped water leaves much to be desired. The fact is that this water is very hard. It contains a large number of salts of calcium and magnesium. Water constantly remains in the faucet and at the junction with pipes. As a result, limescale is formed there, that is, deposits of the same calcium and magnesium salts.
It is not always possible to detect a raid in time. Therefore, over time, it turns into a water stone, which is very difficult to remove.
Accelerates the formation of limescale with frequent use hot water. Since high temperature contributes to the precipitation of salts on the surface.
Regular cleaning of the faucet is the key to a long service life of plumbing.
When cleaning the chrome surfaces of the faucet, certain rules must be followed so as not to damage the coating:
Many cleaners can leave scratches and other damage on chrome, so you should only use proven cleaning methods.
If lime scale has appeared on the tap, it must be removed as soon as possible. For this purpose, you can use improvised means that can be found in almost any hostess:
Laundry soap has disinfectant properties and is able to clean limescale. It is advisable to use soap marked 72%.
Action algorithm:
With this method, you can only get rid of fresh limescale.
Plain baking soda also helps to clean the faucet from limescale. Would need:
If limescale remains in some places, then it can be rubbed reverse side sponges for washing dishes. This must be done carefully so as not to scratch the coating.
One more important condition - do not rub soda into the surface during application, as it has abrasive properties.
The advantage of vinegar when cleaning the tap from limescale is the speed of its action.
Instructions for use:
If the pollution is strong, then another method can be used:
Acetic compress is able to cope even with old limescale.
Another tool to help - lemon juice or citric acid.
Cleaning steps:
If you have a fresh lemon on hand, you can cut it in half and wipe the chrome surfaces with one half. After a few minutes, rinse the lemon juice with water. Lemon juice will also help if you want the faucet to shine like new.
Unusual faucet cleaner - baby oil.
Procedure:
Baby oil works well on soap stains, greasy spots and fresh limescale.
Another tool that is rarely used to remove limescale, but almost always gets good feedback housewives - regular cola.
You can make compresses with sweet soda:
The active substance in this case are the acids that make up the cola.
It is not enough to clean only outer surface crane. Limescale also accumulates inside.
Over time, it can cause plumbing failure.
Aerators are installed in modern mixers - nets on the spout of the crane. When this part is clogged, it must be removed and cleaned.
Signs that the aerator is clogged:
Aerator cleaning steps:
Often the holes in the hydromassage nozzle are clogged. can be heated with vinegar. For this you need:
Deal with old limescale - not the most simple task. It can damage the faucet. To prevent this, you need to regularly clean plumbing from plaque. Then it will serve the owner for many years.
To wash the chrome surface use not only industrial facilities, but also washed in the old fashioned way with soda, vinegar or citric acid. When choosing household chemicals, you need to read the composition, mixers cannot be washed with products containing active acids, alkali and chlorine, from this the coating becomes cloudy and covered dark spots. Below we will talk about how to clean the faucet from limescale without damaging the chrome layer, how to restore the damaged coating, clean the aerator, shower holes and what to do if the faucet is stuck.
The reason for the deposition of limescale are calcium and magnesium salts, which are found in excess in tap water. A whitish coating spoils the appearance of plumbing and even sometimes leads to the fact that the taps are jammed, and the holes in the shower head are clogged with scale flakes.
Soap deposits and limescale are not a big problem, even if the holes in the aerator or shower head are clogged. Any hostess can cope with this task on her own without resorting to the help of a plumber.
It is much more difficult to choose the right products for the care of chrome surfaces in the kitchen and bathroom. Mistakes in the choice of household chemicals can result in a dull surface, scratches and black spots; it is very difficult to restore such plumbing. You will have to put up with a disfigured coating or replace all damaged parts with new ones, which will cost a tidy sum. How to choose the right tool:
It should be said right away that if you properly care for chrome surfaces, then limescale will never appear. You just need to wipe them dry after each use. But what if the raid has already appeared? How to remove limescale from a faucet using products that can be found in every home:
Dilute baking soda with water to make a thick paste. Using a sponge, apply it to all surfaces requiring cleaning and leave for 1 hour. It is important to remember that you do not need to rub the mass, soda will soften the soap and lime deposits. After an hour, carefully remove the remaining gruel. If whitish spots remain in some places, lightly rub them with the hard side of a dish sponge, rinse the mixer with water and wipe dry.
Grate the bar, add a teaspoon of soda and a little hot water, mix thoroughly. Soak a rag in the resulting liquid and thoroughly wash the faucet, taps, shower hose and watering can. To clean shower head holes and other hard-to-reach places use an old toothbrush, cotton swabs and a toothpick. Be sure to rinse off soap residue with water. With this tool you can wash all surfaces in the house, from the bath to the lid kitchen table. Laundry soap is hypoallergenic and at the same time perfectly disinfects.
We will need 9% vinegar, it doesn't matter if it's apple cider vinegar or white vinegar, whichever you have in your closet, a rag and some water. We dilute vinegar with water 1: 1, moisten a rag and wipe all places where there are traces of soap and dried drops. Do not forget to rinse off the remnants of the product and wipe the plumbing with a dry cloth.
There are several ways to remove limescale with citric acid, we will describe two:
Citric acid is an indispensable thing in the household, with its help you can remove not only limescale and scale, but also.
If you don't trust folk remedies, then you can use household chemicals.
Read the instructions carefully, do not forget to wear rubber gloves to protect your skin from the harmful effects of chemicals.
On sale you will find a lot of products designed specifically for the care of steel and chrome surfaces, they will help not only clean plumbing, but also polish it to a perfect shine. All these products are divided into two categories: cleaners and polishes, it is desirable to have both at home.
Purifiers: " Top House for of stainless steel "(Germany)," CILLIT BANG for metal surfaces"(Russia), "Pufas Glutoclean" (Germany), "Sanoks" company Aist Peter, "Cif" (Hungary), " electrolux stainless steel cleaner spray"(Sweden)," Selena Glitter Steel"(Russia)," NEOBLANK"(Cares for and lubricates movable metal joints) country of origin Germany," Ravak Cleaner Chrome"(Czech Republic)," HG"(Netherlands)," SVOD-Effect"(Ukraine) and many others.
Polishes: "Wpro 29945", "Domax", "Indesit", "HG Steel Polish", etc. The polish is applied with a soft cloth to a dry, clean surface and polished to a mirror finish. Cleaners and polishes can be used not only for plumbing, they are also suitable for the care of any metal surfaces: steel plates, sinks, refrigeration equipment, chrome parts of furniture, stainless steel utensils.
Some care products metal products create a thin film that for some time protects the chrome surface from corrosion, limescale and greasy fingerprints. Instead of polish, you can use glass cleaner, of course, it does not create protection, but with due diligence, a beautiful shine is provided.
It also happens that due to improper operation or prolonged inactivity, the faucet or the Bath-Shower switch stops rotating. Can you manage on your own? Yes, if the cause of the failure is limescale or rust.
If the faucet does not give in, you will have to resort to the help of a plumber.
In order not to jam the taps and the shower switch, you need to regularly clean the plumbing from limescale, as well as lubricate the movable joints from time to time. silicone grease, for example: "Huskey™ LVI-50 PTFE Grease" or "CIATIM 221".
Cleaning soap deposits on the outside of the faucet is only half the battle. Modern faucets are equipped with aerators - this is a small metal nozzle with a mesh on the faucet spout. This little detail is used to enrich the water with oxygen, due to which it performs a number of useful features:
It often happens that the aerator becomes clogged with lime flakes and ceases to cope with its functions qualitatively. In this case, it must be removed and cleaned.
How to understand that it is time to clean the aerator:
For work, we need pliers, a rag and a container with detergent composition.
Carefully wrap the nozzle with a rag, clamp with pliers and turn clockwise. And here, an unpleasant surprise awaits the owners of cheap Chinese plumbing: aerators for such mixers are most often made of extruded aluminum or plastic coated with a shiny coating, both materials are fragile and often break when you try to unscrew them. If the aerator burst during dismantling - do not despair, get a new one. Made of steel or brass, quality plumbing aerators last much longer.
If the nozzle is jammed, then use WD-40 or vinegar, wet a cloth, wrap it around the nozzle, wrap it on top plastic bag and leave until the mobility of the thread is restored, this is approximately 2-3 hours.
After you have unscrewed the aerator, rinse it from large contaminants under a tap, and then place it in a glass with 9% vinegar. The exposure time depends on the degree of contamination and varies from 1 to 12 hours. After the time has elapsed, rinse the aerator with clean water, if necessary, clean the holes with a darning needle.
Collect the clean nozzle and screw it into place, you do not need to tighten it so that you can easily unscrew it with your fingers at any time and wash it. It is advisable to remove and rinse the nozzle once a week, then the aerator will work properly.
If the holes of the hydromassage nozzle are clogged, we will use heated vinegar, by the way, vinegar is a universal home remedy which housewives use for various purposes. With it, you can, rooms and even from various kinds household pollution.
Unscrew the shower head, disassemble it into parts and soak them in heated vinegar for 1-2 hours, then, armed with a darning needle, carefully clean all the holes, and assemble everything as it was. Instead of vinegar, you can use " CilitBang and an old toothbrush. When the limescale is gone, assemble the watering can and attach it back to the hose.
Some housewives have found a way not only to wash the taps, but also to protect the chrome parts from limescale for a week. To do this, they use a wax car wash shampoo. This tool is designed to protect the body of the car from adverse weather conditions. The wax in the shampoo forms a thin water-repellent film on the surface that protects the metal from corrosion. You can buy wax shampoo at any auto shop.
Put a drop of shampoo on the sponge and thoroughly wash all the chrome surfaces of the kitchen and bathroom. Buff with a soft cloth or microfiber cloth to a mirror finish. That's all, you can forget about limescale for at least a week.
Perhaps I will upset the readers, but it is impossible to restore the chrome coating at home. However, it is possible to significantly improve the appearance of a faucet damaged by acid or chlorine and partially restore its lost luster. To do this, use a polishing paste for chrome parts car, for example: AREXONS Mirage Cromature Brillanti"(Italy), Goi pasta (made in the USSR) or other similar means. A wide selection of such products is available in any car shop, ask the seller and he will advise you on the right polish.
It is necessary to apply the paste on the damaged surface and polish for a long time with a piece of felt, if the house has Sander with a felt nozzle, the work will go much faster. Since the coating is already damaged, then a similar procedure will have to be repeated from time to time.
Anastasia , November 13, 2016 .Today, water is not flowing from the taps of most domestic cities. best quality. This does not even apply to the fact that it is strongly not recommended to drink it. The thing is, she's very tough. Such water contains a lot of third-party impurities and. in particular salt. The liquid that somehow remains in the faucet or connected pipes provokes the gradual deposition of these salts.
Cleaned mixer
They are the cause of the appearance of an unpleasant raid. Especially often it appears at the junctions separate parts faucet, faucet and sink (sink) joints, with reverse side sinks. All this leads to the fact that it is quite difficult to detect the accumulating plaque in time. When they finally see him, he will already have time to acquire such proportions that it will be extremely difficult to cope with him.
Such deposits are called calcareous because they are predominantly formed from calcium and magnesium salts.
It is these chemical compounds that are found in water in significant quantities. Accelerating the process of plaque formation is possible if you use hot water frequently, since high temperatures contribute to more active formation of salt sediment.
Plaque on the mixer
It is very important to remove the water stone in a timely manner. The fact is that the duration of the operational life of the crane and the mixer as a whole directly depends on this. If you don't want to change expensive pipe fittings every few years, it is highly recommended to pay a little attention technical condition faucet in the bathroom or in the kitchen, promptly cleaning it from accumulating limescale.
Powdered products, as you know, consist of small abrasive particles, respectively, it can damage a thin chrome layer, leaving behind quite noticeable scratches. It is because of this that they are more relevant for bathtubs, sinks, sinks and other enameled products.
Due to abrasive particles, the powder can scratch the chrome plating
Liquid-based cleaners do not have abrasive particles. Therefore, it is advisable to clean the taps from salt deposits with their help, since their action is much more easily tolerated by the metal components of the mixers.
Liquid products to be careful of the chrome-plated surface
Considering the fact that household chemicals far from always suitable for dealing with limescale on taps, you can resort to more simple ways traditionally referred to as domestic. Their essence lies in the fact that you do not have to run to the store for any expensive or cheap chemical agent– all the ingredients necessary for the event are already at home.
You can clean the mixer with improvised means
Perhaps the easiest way to get rid of a sickly plaque. The mesh must be soft. You should also take care of gloves. You need to rub very carefully, because we must not forget that the chrome surface is subject to the influence of abrasive materials.
Take a regular brush and some toothpaste. This substance copes well with many contaminants. An important advantage of the brush (the bristles must be soft) is that it is able to penetrate into hard-to-reach places.
A small amount of regular salt poured on a clean, damp cloth, after which the tap is gently wiped at the site of contamination. Salt is an abrasive material, we must not forget about it, and therefore it is also necessary to clean with it very carefully.
Despite the fact that chrome surfaces do not mix well with various acids, this does not apply to lemon. You need to take a piece of lemon and carefully rub it all the surfaces on the mixer. After that, they are washed with clean water and wiped with a dry cloth. To date, this is one of the most effective answers to the question - how to clean the taps in the bathroom from limescale.
It is necessary to use not concentrated, but ordinary light table vinegar. It is necessary to moisten a piece of cloth in it, then wrap it around the mixer and leave for an hour. Next, you need to thoroughly rinse the faucet with water and polish it thoroughly with a clean cloth.
A versatile product that can cope with almost any household pollution. You need to prepare a special tool - add a certain amount of water to make a thick paste. This mixture lubricates the faucet (not rubbed!). Literally after half an hour or an hour, it is washed off, and the cleaned place is carefully polished with a cloth. This method will help if there is not too much plaque yet, and therefore it has not had time to eat. It is necessary to prepare a concentrated soap solution, moisten a kitchen or bath sponge in it, then wipe the mixer with it. Next, you need to thoroughly rinse the substance and polish the cleaned areas with flannel.
Even they can help in solving the painful issue associated with limescale. Toothpicks are taken by both edges, strongly pressed against the tap and stretched along its surface. This method is relevant only for small salt deposits, as well as for the corresponding pipe fittings, for example, square-shaped taps.
Ideally, the faucet should be cleaned daily. Do not be lazy, and after each opening of the tap, wipe it several times with a regular cloth. If the mixer is constantly dry, then, accordingly, limescale will not appear on it.
In bathrooms and kitchens, a lot of salt deposits accumulate on metal plumbing structures. They are not easy to clean due to complex shape and varied coverage. If you clean in the usual way, the surface takes on a rather unpleasant dull appearance. For the metal to shine, simple perseverance and diligence are not enough - special knowledge is needed to apply them to the care of water taps. All of them have a stainless surface, which is made of different materials: stainless steel, copper, nickel, chrome, bronze and brass. The choice of means should take place depending on the coverage. Here are a few tips on how to keep your faucets in order.
Do not forget to clean the faucet aerator - it accumulates there largest number deposits. After cleaning, but before wiping dry, you can apply window cleaner to the surface. This will add an intense shine to shiny surfaces. Never use abrasive cleaners on faucets of any material before carefully reading all manufacturer's instructions and warranties. Too hard or just careless cleaning will damage the coating and degrade it. appearance. If you use a cleaning cloth, make sure that it is as soft as possible and does not scratch the faucet.
Keeping a bathroom clean is a lot of work, requiring precious time to be spent cleaning and refinishing faucet parts. Under the influence of dirt, dust and soapy water, faucets fade, become covered with stains and various deposits. Cleaning the taps in the bathroom is quite problematic due to the complex shape and features of the coating, so plumbing owners should familiarize themselves with simple and effective ways care and cleaning of faucets.
Most importantly, before you start disinfecting and cleaning, you need to determine the type of faucet cover. This is required for the correct choice of products and a more delicate cleaning of the surface of the mixer, based on its features:
Chrome and nickel-plated mixer surfaces require a special approach to cleaning and disinfection. To wash the mixer, you can use the following products:
One glass warm water to be mixed with a tablespoon detergent. Next, soak the sponge with the solution and carefully clean the parts of the product. invert Special attention you need on the base, spout, valves and levers of the crane.
How to clean rust chrome faucet in the bathroom with ordinary soda? Using a soft, damp sponge or cloth, the baking soda is distributed over the contaminated surface and left for half an hour. Then it is washed off with cool water.
6% white vinegar is poured into a spray bottle and spread over the chrome and nickel surfaces of the product, dissolving mineral deposits. Do not touch the vinegar drops for 10 minutes. Wipe the mixer with a dry soft cloth.
A copper faucet begins to fade over time and become covered with a greenish-brown coating. The next step is to clean the copper faucet in the bathroom.
The spray bottle is filled with ordinary Cola or Pepsi. Soda is sprayed onto the mixer and soak for a few minutes. clean water rinse and gently wipe with a damp cloth. Thanks to the acid contained in carbonated drinks, they do an excellent job of cleaning copper parts of the product.
To clean the copper product from green plaque, you will need to remove the mixer and boil it in water with the addition of vinegar and salt.
Knowing how to clean brass faucets in the bathroom, you can quickly and easily return a tarnished product original view and a noble matte finish. Most effective recipes brass faucet cleaning are shown below.
For its preparation, one tablespoon of 6% vinegar, salt and wheat flour is required. The cleaning mixture is spread over the surface with a damp sponge. Next, the faucet parts are rinsed with cool water and wiped dry with a soft cloth.
This is effective remedy will help restore the brass faucet shine and cleanliness. The faded areas are covered with tomato paste and aged for about half an hour. Then the cleaned mixer is rinsed and carefully wiped.
An excellent prevention against dullness and darkening of brass is the periodic application of a thin layer of linseed oil to the water tap.
With the help of citric acid and salt, you can restore the brass product to its former radiance. To do this, cut a small lemon in half, sprinkle with finely ground salt and wipe the surface of the sanitary ware with it.
Bronze faucets, just like brass ones, darken very quickly and take on a dull look. If the bronze mixer is too dirty, a specialized paste, such as Trilon-B, will be required to clean it. In other cases, homemade cleansers can be used.
To prepare a cleaning composition, 3 tablespoons of chicory are diluted warm water to a mushy state. Ready mix spread over the contaminated bronze surface. Washes off after a while.
At heavy pollution a solution of potassium and caustic sodium helps. The composition is evenly applied and aged for about half an hour. Then it is thoroughly washed and dried.
Important! To avoid damage and scratches when cleaning brass or bronze faucet do not use metal brushes and too hard fabrics.
Another important problem in the operation of the mixer is the accumulation of dirt between the parts of the product. To clean such hard-to-reach places, a few simple tricks will come in handy:
Timely cleaning of the water tap from various contaminants will allow you not to waste energy on removing old stains and dissolving mineral deposits in the future. If you regularly follow the above recommendations, in the bathroom you can not only enjoy cleanliness and radiance, but also significantly extend the life of the sanitary ware.
kayabaparts.ru - Entrance hall, kitchen, living room. Garden. Chairs. Bedroom