Creation of figures for the garden from polyurethane foam. Foam crafts - garden decoration and your pride

Would you like to ennoble your summer cottage or the area near a private house, but are tired of the consumer goods that are offered in the store? Or do you want to decorate the playground? Then think about whether to do everything yourself with the help of ... polyurethane foam.

In fact, the choice of polyurethane foam as a material for sculpture is unusual only at first glance, because given its pliability and softness, it becomes quite clear that crafts made from this material are gradually gaining popularity.

Necessary materials

What do you need to create foam sculptures and where to start?

In fact, the list of materials is short:

• plastic bottles;
• spray foam cans;
• dye;

Plastic bottles will be needed as a frame for future figure and their volume directly depends on the size of the sculpture. The amount of foam is also calculated from the size of the planned craft. It should be noted that the volume of foam at the outlet of the cylinder is from 50 to 70 liters. Usually there is a marking on the cylinders indicating the amount of foam coming out. The choice of paint directly depends on you, it can be either oil or in spray cans or any other. It should be true to note that if it is supposed to use crafts on the street under open sky, you should choose a paint that is resistant to natural influences.

To make a sheep, you will need the following amount of materials:

• plastic bottles 4 pieces of 2 l;
• isolon (this is a special substrate for linoleum, can be purchased at any hardware store);
• 5 cylinders of polyurethane foam, 70 l each;
• adhesive tape or, in other words, adhesive tape;
• paint, varnish;

First, we make a frame from plastic bottles. It doesn't have to be perfect, just well made so it doesn't fall apart.

Then you should cut the isolon into narrow strips 2-3 cm wide

The next step is to wind the frame with isolon strips to give it more volume. We fix the strips of isolon with adhesive tape so that they do not unwind.

After the frame is wrapped with isolon, you can attach a sheep's tail made of ordinary wire.

After that, you can apply mounting foam to the frame. The foam is applied in layers. Apply each new layer only after the previous one has dried, for quick drying it can be sprayed with water. The fact is that water coming into contact with the foam starts a reaction, which accelerates the solidification of the foam.

The foam should be applied as evenly as possible so that imperfections do not have to be corrected.

After our sheep is shaped with the help of foam, and the foam finally hardens, you can proceed to the details. For starters, you can glue the ears.

Then you can correct the muzzle of the lamb with a clerical knife, and then decorate it.

It remains to paint the hooves, draw eyes, and the sculpture is ready.

It should be noted that foam is a fairly toxic material and should only be handled in well-ventilated areas. It is also quite sticky, and therefore you should stock up on acetone or a special solvent for mounting foam and patience.

In general, foam is a fertile material, and almost any figure can be made from it, for which there is enough imagination, as well as patience and time. Starting from the simplest and smallest and ending with the size of a human being.

How to make an ironing board

Crafts from polyurethane foam can be made with your own hands in just a few hours.

If you have a disposable tank that hasn't run out yet, why not put it to good use. landscape design.

In this case, it is still better to resort to professional foam, and not household foam, since a small gun with a diameter of 2 mm is added to it.

Unusually simple and beautiful figurines made of polyurethane foam will become the property of your site. They will not leave indifferent either neighbors or just people passing by.

Materials for fakes from polyurethane foam

You will need:

• gloves;
• sprayer with pre-prepared water;
• polyethylene;
• aviation kerosene.

Kerosene is needed so that, upon completion of work with mounting foam, hands can be easily washed from building material.

Something will also come in handy for creating the basis for crafts from polyurethane foam with your own hands.

You can take an ordinary plastic bottle, an old pan or something else, which is not a pity.

With foam coating auxiliary material creating crafts and begin ...

You need to paint them carefully, and before carrying out this procedure
dry thoroughly in the shade. Drying takes at least a week, but if the foam layer is large, it is better to wait longer.

The paint is applied to the craft from mounting foam with your own hands every spring again. If this is not done, the foam may crack and the craft will deteriorate.

Foam craft ideas

If your site has a small pond, you can make a large green toad. This is especially true where many plants grow, especially large-leaved ones. In some cases, it is easier to make a lizard or a crocodile - who can do what.

In order not to miscalculate with the sizes and “fill your hand”, you can practice on plasticine. No matter how strange it may sound, but it was after trials on this simple material, it turns out to make chic crafts from polyurethane foam.

The same goes for the dough - if you like to bake delicious buns, pat animals - this will help you figure out what you can do better.

Perfect solution- make turtles from polyurethane foam. And it is not at all necessary to have a reservoir on the site. Besides, White paint Almost everyone has it, and now it costs less than colored ones.

Turtles are easier to dye, their shells can be alternated with natural ones. If, during the creation of the craft, bumps appeared that should not be, they can be cut off sharp knife.

Similarly, the situation will be with rounded details - if they need to be sharpened, the excess is simply cut off.

Crafts from polyurethane foam not only street views decorate, they can be made for the home. Funny frogs will bring smiles to people passing by!

Yes, as original New Year's decor you can make a snowman out of foam, but you need to start creating in advance so that the material has time to dry well.

If you paint over the foam ahead of time, it will quickly crack.

Mounting foam- a unique building material that is widely used for installation, sealing structures and increasing their thermal insulation. Lovers of garden decorations have expanded the scope of this building material. Do-it-yourself garden figures from polyurethane foam can be easily made by each owner country house or suburban area. In this article you can see photos of finished crafts, as well as popular foam sculptures.

1. Light weight.
2. Ease of use (applied to any surface, easy to cut).
3. Ability to make crafts of any size.
4. On ready product not affected by precipitation and temperature changes.

Terms of use of mounting foam for garden sculptures

Terms of use of mounting foam for garden sculptures

If you have never worked with mounting foam, we recommend that you read the instructions from the manufacturer. Do not forget that the foam inside the balloon is a liquid mass, and when it comes into contact with air, it begins to harden. Complete solidification occurs after 10-12 hours. When working with foam, use products personal protection. It is not recommended to work with sub-zero temperature air.

Shake the can well before each use of the mounting foam. During operation, hold the can with the cap down so that the gas does not escape from it and all the foam can be used. Do not immediately apply many layers, as the uncured will fall off. Do everything gradually, apply the next layer at least 10-15 minutes after the previous one. For ease of application, use a special gun.

The appearance of the polyurethane foam figure directly depends on the type of frame. You should first find a picture of the figure or make a sketch to take into account all the nuances and the finished product looked like a wooden or plaster sculpture.

For the manufacture of the frame, you can take different materials, for example, plastic bottles or iron cans are suitable. You will also need wooden planks, rebar and wire. To make the sculpture stable, you need to fill it with sand.

Now you can start decorating crafts with mounting foam. Evenly distribute the foam over the frame, taking into account the future reliefs of the craft. When it completely hardens, it will be possible to remove unnecessary parts with a clerical knife and correct defects. If necessary, add foam to places where you forgot or want to fix something in the craft.

A layer of putty will help protect the mounting foam from destruction. To make the garden craft smooth, grout is carried out sandpaper. Now take acrylic paints and cover the figure. Preferably two layers or more. To prolong the life of the future masterpiece, it is varnished on top.

Garden figures can be additionally decorated with the most different materials such as beads, flowers or make LED backlight so that the sculpture glows at night.

To make a garden snail, you will need half a can of foam. Cover the table with oilcloth and start applying foam for the base of the snail. When the first layer dries a little, apply a second one and insert a kefir bottle in order to make a snail's neck. Cover the neck with foam too and shape the head with your hands.

Make snail horns and a slightly elongated muzzle. After that, you can start making the shell. To do this, a round hill of foam is applied to the body of the snail. Now insert a bucket that will be designed for flowers and turn the garden craft into an original flower bed.

With a marker, mark where your snail shell begins and ends, and make curls. When the foam is completely dry, sand the product. It remains to decorate the snail and the garden craft is ready.

Materials:
- an old saucepan;
- iron can:
- oil or acrylic paint;
- foam bottle;
- wire;
- beads.

1. Separately fill the pot and jar with foam and let dry.
2. The jar is the head, and the pan is the body of the frog. Fasten these parts with wire and fix with foam.

3. In the place where the frog handles should be, fix the wire and also cover it with mounting foam.
4. Now shape the head and torso to look like a frog. Make the lower legs as well.
5. Paint the craft with paints and then insert the eyes. The frog is ready, now it can be placed near the pond in the garden or near the pool.

To do garden figurine foxes, you will need a plastic bottle. Fill it with sand or pebbles, then the wind will not be able to turn your product over. Foam the bottle, but not immediately with a thick layer, but gradually, pausing for about 15 minutes to set the foam.

For the manufacture of paws, you can use a rubber tube. To make the paws flexible, insert a wire into the tube. The tail can also be made from a tube, which will need to be well lathered. For the neck, use a cardboard cylinder from under toilet paper. Install some kind of round blank for the head on it.

Propene everything well and give the sculpture appearance foxes. Then paint the shape oil paints and varnish. Keep in mind that if the paint is white, then the varnish will give it yellowness.

A plastic ball can be used as the frame of the kolobok. Place it on some kind of support, such as a jar or bowl. Apply foam now, waiting for each layer to dry. To make handles, insert wire.

Also form a scarf out of foam, and you can make ears out of cardboard. When the foam is completely dry, cut out the eyes, mouth and nose with a clerical knife. Make legs out of wooden planks. It remains to color the craft and the gingerbread man - ready!

It is interesting that not only garden figures, but also an original lantern that will give your personal plot notes of exclusivity and will help decorate the garden in Japanese style. To make a lantern stand, take a pipe that needs to be foamed from the bottom side and set on a flat wooden base. For the bowl of the lantern, you can use a plastic bowl, which must be fixed on top.

Now pour the foam in layers, waiting for the partial drying of each layer. Come up with a picture for the design of the lantern, draw a diagram and embody the idea with the help of mounting foam. Make a hole in the center of the bowl so that you can secure the lid with screws. Insert the bars into the bowl and froth them.

Attach the lid to the bowl with screws. Now cut out a smaller square from the chipboard. On one side, foam it, and on the other, fix the racks. In the center of the squares, you need to make a hole in order to insert a lamp into it later on. solar battery. Hide the wires.

After that, a roof is made from a large piece of plywood, which is installed on racks. To make the relief pattern beautiful, first draw it with a marker on the surface of the lantern, and then gently cover it with foam.

Garden figures from polyurethane foam master class

The finished product is completely painted. To install it, you need to dig a pipe into the ground a little or make a small flower bed around the lantern.

Do-it-yourself polyurethane foam figures help transform any garden plot. Even without the skills of a sculptor and artist, you can make a beautiful sculpture that will enliven your exterior.

from polyurethane foam can also be used to decorate rooms or facades of buildings.

Not applying special efforts and material costs, foam crafts will be an excellent decor and decoration for any summer cottage. It's no secret that for many, a dacha is a place where people come to relax from the city noise, rhythm and bustle. Therefore, it is very important that the dacha is exactly the place where a person can truly enjoy life and relax the soul. Often the maintenance of a summer cottage and its decoration require considerable Money, patience and time, but with foam everything is different.

In order to make any crafts from polyurethane foam with your own hands, you do not need to have any special education- absolutely everyone can cope with this task, it is enough to have good imagination and imagination.

In construction, polyurethane foam is used very often and in in large numbers. It is used to seal small gaps and has the ability to expand, while filling all the voids.

Important! The curing of the foam depends on what brand of foam it is, but on average it takes from 15 to 25 minutes.

You can cut off excess parts from finished products only after the foam has completely hardened.

You can cut off excess parts from finished products only after the foam has completely hardened.

Any crafts can be made from building foam, since foam is an unpretentious material, and when frozen, it can withstand any temperature, in addition, foam crafts do not undergo any serious changes when atmospheric precipitation hits them.

The material is lightweight and does not have sharp corners, so crafts from mounting foam are often made for kindergarten or platforms. Such crafts can have both large and small size, but the weight of the craft will be small.

When working with polyurethane foam, it is necessary to use a foam gun, which is put on the can, and at the end of the work, a cleaner for the gun is used

How to work with mounting foam?

To work with polyurethane foam, a minimal set of tools and accessories may be required - several pairs of gloves, preferably rubber - the fact is that the foam has such unpleasant abilities, quickly sticking to hands, so it is simply impossible to do without gloves. In addition, you will need 2 or 3 knives of different sizes - they are needed after the foam has dried in order to give the products the necessary shape and to cut through small details, such as eyes, nose, mouth. When working with polyurethane foam, it is necessary to use a foam gun, which is put on the can, and at the end of the work, a cleaner for the gun is used. For painting finished products, you will need paints and brushes. In order for foam crafts to last as long as possible, it is recommended to varnish them.

Important! Polyurethane foam is a very light material, so every time before doing some new craft, it is important to take care of its weighting, otherwise the structure will not hold.

Therefore, it is necessary to place something heavy inside each structure - it can be a container with sand, a piece of iron, a plastic bottle of water. You can use anything, the main thing is that the thing should at least fit the shape of the future craft (if the finished product is small in size or volume), and be weighty.

It is important to remember that all work performed with mounting foam should be carried out only in a well-ventilated area. The temperature should be at room temperature. If work is carried out on fresh air, then you need to do it in good weather, but you can’t work in direct sunlight, you need to move into the shade.

During operation, it is important not to forget to shake the foam can before each use.

Finished foam products must be coated with paint, but it is important to remember that the content of nitrocellulose is unacceptable, since this substance adversely affects the foam, as a result, the craft softens, and the entire structure may lose its shape.

Hedgehog figurine made of polyurethane foam

Foam crafts

Animal figures are especially popular among polyurethane foam crafts. You can place them in any part of the garden, placing a lonely figure by the pond or on the lawn, or create a whole composition. In the manufacture of crafts from polyurethane foam for kindergarten, figurines of fairy-tale characters are mainly created:

• Hedgehog. This figurine is very easy to make and perfect for beginners. Any material can be used as a frame, it all depends on the preferences of the master. When the foam has hardened, with a knife you need to carefully cut off all the excess and give the product the desired shape. Hedgehog needles are made from toothpicks, which must first be prepared for work - they must be painted black, leaving a small distance intact. The part that needs to be stuck into the figure remains unpainted. If desired, the other end of the toothpick can be painted in golden color. Before sticking toothpicks into a hedgehog, the figure must first be painted and allowed to dry. In these photos you can see step by step manufacturing such crafts from polyurethane foam as a hedgehog.

Foam Goat

• Sheep and lamb. A master class on the manufacture of such crafts from polyurethane foam, such as a ram and a sheep, should begin with the manufacture of a frame. The frame can be made from several plastic bottles interconnected with adhesive tape. In order for the design to be stable, the bottles that will be used as lower limbs must be filled with sand or water. After the frame is completely ready, you can proceed to the main work - to process it with mounting foam. Foaming should be done gradually, in layers. Each applied layer should dry thoroughly (15-20 minutes), and only after that you can apply the next one. What the craft will be after the final processing becomes visible after the first layer. After the final layer has been applied and dried, with a knife you need to give the figure its final shape, and then paint it.
• Goat. These photos show step-by-step instruction to make such crafts with your own hands from polyurethane foam, like a goat. For the frame of the body, you need to use plastic bottles, previously wrapped with tape or wire. Remains are used for the leg frame metal pipes, which should be the same length and thickness. The resulting structure must be securely fixed to the ground, and care must be taken to ensure that the base of the body is securely fastened to the legs. The product is covered with one or two layers of polyurethane foam. In order to make horns and a tail, you can use scraps of thick branches, securely fasten them and apply another layer of foam to the goat. Before painting on a goat, you need to apply one thin layer primers. Large buttons can be used to make eyes.

Kolobok from polyurethane foam

• Kolobok. This photo shows a craft in the form of a kolobok, made by hand using mounting foam. As a frame, you can use a medium-sized plastic ball. The ball must be covered with foam in several layers, while not forgetting to dry each layer. The hands of the kolobok are made of a plastic tube with a wire stretched inside. Hands need to be fixed on the kolobok and treated with foam. Small ones are used for the legs. wooden bars, which must also be fixed and applied with foam. The scarf is also made of foam. And as a frame for the ears on the scarf, you can use cardboard. The finished kolobok needs to be painted, varnished and planted on some kind of stump.
• Figure for growing flowers. In order to make an original flower pot, you can make any foam craft. But it is important to remember that in the middle part of the figure you need to fix a container for growing flowers - these can be: a deep basin, a tin bucket, a large plastic bottle with a cut neck.
• New Year's crafts. Such foam crafts can be made both at their summer cottage and on the territory of a kindergarten. A Christmas tree ball can be made from a tennis ball by covering it with a layer of foam and painting it with bright colors.

In order to make a Christmas tree, you must first make a frame. The frame is made from a cone made of cardboard. The foam is applied in several layers on a cone-shaped frame. As it dries with a knife, the figure is shaped like a Christmas tree and painted in the appropriate color.

What a person can't think of! It would seem that out of an unnecessary thing that just needs to be thrown away, you can make something unusual and useful, breathe new life into it.

Usually old ones are adapted for a summer cottage. car tires, tires, plywood sheets, old stumps and snags and other items.

Have you ever thought that you can make interesting crafts from polyurethane foam for a summer residence? Some of you have probably heard of this, but most of you must have been surprised. Therefore, today we will tell you what can be made from this material and how to turn it into a craft.

What crafts can be made from mounting foam for the garden?

Polyurethane foam is a very common building material. With its help, seams and voids are closed, in which it expands, filling the entire space. After hardening, it becomes solid, but the weight is small. When creating crafts from it, it is worth considering the basic properties of this material. In addition, the mounting foam is easily trimmed.

Why can it be used to create crafts? The fact is that mounting foam takes any shape, and its positive property - resistance to various adverse environmental factors - allows you to exhibit crafts in the garden. They are not afraid of either precipitation or frost.

Light weight and lack of sharp edges and corners makes such crafts safe for kids. Therefore, you can safely place your masterpiece on the playground. You can also make enough out of foam large structure, which, as mentioned above, will have a small weight.

From polyurethane foam, the most popular figures are various animals: frogs, sheep, hedgehogs, cows, etc. They will look great at the pond, flower beds, on the playground, near trees and shrubs, and even in the middle of the lawn.

The craft can be either stylized, cartoonish, or very “live”, similar to a real animal. It all depends on your personal preferences.

In addition to animals, you can make mushrooms, stylized beautiful flowers. They look no worse than those made of stone, stump or wood.

With a strong desire, you can even build a mini-house, an airplane, a tower and other similar structures. In addition, making garden crafts from polyurethane foam is a very interesting activity that will help you take your free time. And the ease of working with it building material won't cost you much.

We make garden crafts from polyurethane foam with our own hands

When working with this material, some rules must be observed. So, polyurethane foam has such a property as a quick setting with the surface with which it comes into contact. The same with our hands - they must be protected from foam sticking. To do this, you will need gloves made of fabric (cotton), and let there be several pairs of them.

You should also prepare a special cleaner in advance, with which you can clean the mounting gun at the end of work. By the way, you will also need it, as well as the mounting foam itself.

Having bought everything you need and decided on how your craft will look, you can get to work.. The technology is not complicated, you need to make the frame of the figure and cover it with foam in layers, each of which dries for about 15-20 minutes. Any materials at hand are suitable for the frame: boards, old unnecessary pots of different diameters, various jars and other containers.

It's like an artist draws a picture - first the circles, squares and ovals that make up the figure, and then begins to draw the details. So here - fill in the form from above and with the help of a knife give the features you need.

The finished figure can be painted, and varnished on top. Such a simple technology will allow you to create almost any craft for the garden.

Now let's look at a few concrete examples . It's very easy to make a cute hedgehog. This craft is perfect for a beginner. In addition to the materials discussed above, you will also need toothpicks. We make an ellipse out of foam, which will be the body of the hedgehog. When it hardens, cut off the excess, forming a figure. To make the hedgehog smooth, you can glue it with several layers of toilet paper with PVA glue.

After that, we start sticking toothpicks. Moreover, they can first be dipped in 3/4 in black paint, and the tips in gold. It is better to paint the hedgehog itself before attaching the “needles”.

It is also easy to do ladybug . Fill the hemisphere and cut out the desired shape, then paint. When choosing paint, be careful, it should not corrode the mounting foam.

If your vase is broken, do not rush to throw it away. It is enough to cover it with foam, which will hold the shards together, and when it hardens, cover it with paint. Gold or silver coloring looks beautiful, and the vase itself can not be cleaned. Leave it embossed and bumpy.

More complex crafts require some skill and more time. For example, to create a deer, the most difficult thing is to make a frame. Large plastic bottles are suitable for the body, legs are made of wire, and a cup is for the muzzle.

Then slowly apply layers of mounting foam in turn. Then we clean, give the final shape, primer with paint (acrylic), apply varnish and paint. As a result, you will get a cute deer, almost like a real one.