Homemade telescopic arm for the monitor. Do-it-yourself TV mounting on the wall with and without a ready-made bracket

One of the options for placing flat-panel TVs is to mount them on the wall. This solution allows you to save space, while everything looks stylish, modern. But factory-made brackets, despite their great functionality, have one drawback - they are overpriced. Since the bracket scheme is simple, it can be made independently from any materials available. Let's take a closer look at how to do this.

Basic requirements for mounting a TV

Most TVs on the market use the VESA mount system. Based on typical hole spacings (in millimeters), various mounting modules are offered. Usually these are four mounting points, which are located on the rear panel. The "four" VESA scheme is made in the form of a square or a slightly elongated rectangle. The fixing points can already be fitted with standard fixing bolts. If they are not there, then they are in a separate package or with other components.

It is impossible to mount a TV, which is especially important for expensive branded models, on non-standard fasteners. Therefore, the bolt heads are often designed for special tools, and the holes are filled with soft plastic. In such cases, installation of the product on a factory-made bracket must be done by a certified technician. Without his mark in the warranty card on the work done, all warranty obligations are canceled!

When installing standard dowel brackets on main walls, it is recommended to choose steel, at least propylene. For walls made of foam block, cinder block - only propylene. Self-tapping screws with a diameter of 4 mm or more, or such as the first digit of the screen diagonal size (in inches). Deepening the self-tapping screw bearing wall without finishing thickness should be:

• for concrete walls - 10 mm plus the diagonal size in centimeters;
• for brick walls– 30 mm plus diagonal size;
• for foam block walls - 50 mm plus the diagonal size.

The requirements listed above do not apply to plasterboard walls, since they do not have good bearing capacity. If the sheets fit snugly against the main wall, then the installation is carried out directly on the wall. Then, under the diameter of the dowel head, holes of the corresponding diameter are drilled in the sheet. And having placed a spacer made of a steel bar on the dowels, a 6-sided socket wrench, tapping with a hammer, upsets them until they fit into place.

If drywall sheets fixed on the frame and the skin thickness is less than 12 mm, you will have to look for another place or install the TV on the cabinet. The only one possible variant– if you know the location of the frame that can be used to attach the bracket.

Fixed wall bracket structures

One of the most common designs is the fixed bracket. Fixing system very simple, but it can not be tilted, rotated the screen. Fixed bracket for TV on the wall, it is easy to mount and can be made from any components that are affordable or easy to find.

Consider the option of making a fastener made of wood. Main materials:

• two wooden planks;
• self-tapping screws with a ring;
• hooks and plastic dowels.

We take two planks of hardwood, they have the best quality. The length of the slats should exceed the length of the back wall of the flat-screen TV housing by 10-15 centimeters. To ensure that the screen tilts at a slight angle, we take the upper bar slightly thicker than the lower one. We fasten two self-tapping screws with a ring to the upper edge of each of the planks.

With the help of bolts that we twist in special holes, we fix the slats on back wall TV. One bar on the top and one on the bottom. Between the rings we measure the distances horizontally and vertically, and transfer them to the wall. We get attachment points. We drill holes in them, install dowels with hooks and hang the product on them.

Given wall mount– easy to manufacture and very reliable. Suitable for models whose screen diagonals exceed 26 inches.

Consider another simple option for making a fixed wall bracket. We will install a small diagonal product on aluminum corners and a bicycle spoke. Steel corners can also be taken, but since the loads on the fastening are insignificant, and steel is difficult to process, aluminum is preferable.

Main materials:

• four aluminum corners;
• one bicycle spoke 2 mm thick;
• bolts, screws, plastic dowels.

We select the installation location of the flat TV, the size of the dowels and holes individually, taking into account its size. We fasten two corners with two holes drilled on each to the back cover with bolts. The other two - on the wall with screws. To do this, we apply them to the wall and mark the holes for the dowels on the wall with a pencil. Fasteners are best done with plastic dowels. To connect the corners to each other in the upper side of each of them, we drill one hole.

It is desirable that one pair go inside the other, so we make the distance between the corners fixed on the wall a couple of millimeters smaller than the distance between the corners on the TV. Having attached them in place, we apply the TV to the wall. We expose the holes drilled in the upper side plane of each corner in one line, and thread a bicycle knitting needle through them.

The spoke holds the product in a vertical plane, and the corners inserted into each other prevent its involuntary displacement in the horizontal plane. If the TV needs to be removed from the wall, then we take out the spoke and the connection is disengaged.

Despite its small diameter, the heat-treated bicycle spoke can easily support the weight of smaller models. But for heavier ones, larger diameter studs are needed!

Swivel structures – more freedom of action

Swivel designs provide greater freedom of action: turning the screen in the right direction, its approximation. Some types of structures regulate vertical angle screen tilt, which is necessary when the product is hung high. Therefore, the swivel wall mounted TV mount provides convenient viewing from anywhere in the room.

Main materials:

• two metal plates;
• piece of pipe, square profile;
• connecting bolts, screws, dowels.

For the manufacture of an inclined bracket, we take two metal plates. The larger the size of the diagonal of the TV, and the greater its weight, the bigger size plates must be taken. For small models, we take two plates 20x20 cm, a few millimeters thick. One will be attached to the wall, and the other on the back panel. We install two metal corners on each plate.

In order for the mount to have sufficient freedom of movement in any direction, we install a piece of pipe between the corners. But it is better to use a 2x2 cm square profile, since it will be more convenient to fix it, set it in a plane.

We place a piece of pipe between two corners and connect it with a long bolt. Then screw it onto the plate. The pipe (profile) must rotate freely and not touch the end of the plate.

To the wall-mounted plate, we fix the corners parallel to the floor. This will allow you to change the angle of the TV to the right or left. And the corners on the plate mounted on the rear panel are set perpendicular to the floor. This will allow you to adjust the angle of inclination.

To increase the mobility of the system, instead of one piece of pipe, it is better to use two connected by a long bolt. This will allow you to zoom in or out of the screen, adjust the distance from the wall.

Thus, we can make any type of bracket with our own hands. It does not require special knowledge, and material costs are minimal. Having shown imagination, you can improve the design and make it more interesting, individual. Paint in a color that goes well with the interior of the room. At the end of the work, you can watch your favorite programs and series with great comfort!

Modern monitors make us happy stylish design and amazing image quality, and you can place them anywhere, you just need to purchase a monitor arm. Having decided to install such equipment on the wall, you, of course, can turn to professionals. However, if you are able to take a few measurements and screw in a couple of screws, then you can do this work yourself.

Wall mount and its types

The wall bracket is a special mount that is designed to install the device on the wall. Today in stores you can find a huge number of brands and models, but among them there are three main types of monitor brackets. Their main difference from each other lies in how much they allow you to change the angle of the display, which makes it possible to get rid of glare. Before attaching the equipment, you need to make sure that you have wall bracket suitable for this model. The most common standard today is VESA.

There are several basic types of monitor mounting on the wall:

• hard fastener;
• inclined fastener;
• swivel mount.

Rigid fasteners allow you to hang the device on the wall at a distance of several centimeters from it. This monitor wall bracket does not have any adjustment function. After installation, you will no longer be able to rotate or tilt the device. In this regard, it is best to mount it on such fasteners at eye level. The main advantages of such a holder are reliability and low price.

The tilting monitor arm allows you to mount the display above eye level, allowing you to change the angle depending on the situation. Depending on the manufacturer of the brackets, the angle of inclination may vary, but average is about 10-20 degrees. In this case, the monitor is mounted on the wall at a distance of 10-15 cm from it.

The swivel mount allows you to tilt, rotate or move the monitor as you like. This option is the most functional. But the cost of such a bracket is several times the above models. Please refer to the specifications of the bracket for size and weight limitations of the monitor. Based on this, you will be able to choose the best ratio of performance and cost for yourself.

Bracket placement height

Many people mount the monitor too high on the wall, which can cause discomfort when viewing and pain in the neck due to the awkward position of the body. Most experts advise placing such a technique at eye level. some exact value, at what height to hang the device, of course, no. Optimal Height the location of such a unit depends on its size and the area of ​​\u200b\u200byour room. In a spacious room, the display can be positioned higher than in a small one. Best to test in person different variants.

When choosing the optimal location for the monitor, you should pay attention to the strength of the wall. It is not difficult to install the bracket on a wall made of concrete, wood or brick, but if the wall is finished with plasterboard, then do without special devices and there is no definite experience. In this regard, it is not recommended to install monitors weighing more than 30 kg on such a design, and if installation cannot be avoided, then special butterflies must be used, and the bracket should be attached to the base of the supporting profiles.

No less important are the climatic features of the object. We all know that the performance of any device is highly dependent on external factors. In this regard, when choosing a place to install the monitor holder, you must consider the following factors:

• do not hang the monitor in rooms with high humidity or in an area with strong exposure to sunlight and heat;
• if the monitor is installed in some confined space, such as a niche, it is necessary to ensure constant air exchange.

Once you've decided on a location, take masking tape and mark the location of the monitor on the wall surface with your own hands. For good air exchange around the perimeter of the monitor, it is necessary to leave free gaps of at least 20 cm.

Bracket mounting process

As a rule, the wall bracket for mounting the monitor consists of two parts:

• plate, which is attached directly to the wall;
• fastener, which is installed on the monitor.

The wall bracket is attached to the monitor with special screws. The holes intended for them are located on the back of the monitor and are sometimes covered with plastic plugs. Measure the gaps between the screwed fasteners and the edges of the monitor. Using this data, you can calculate and mark the location of the plate, and then drill holes in the wall. Using dowels, you will need to screw the plate to the wall, then hang the monitor and bracket on it, then both parts will be fastened.

Homemade fasteners

If you want to save some money on buying a monitor holder, you can make it yourself. To do this, you will need an asymmetric duralumin profile, M4 screws, dowels and 20x4 self-tapping screws. Measure the distance between the holes on the back of the monitor. Then cut two guides from the profile. The finished rails are carefully attached with M4 screws to the back of the device.

At this point, the first stage of work can be considered completed. You just need to attach the monitor to the wall. For this you will need furniture board, to which the two remaining guides from the profile are attached. With the help of dowels, the furniture board is attached to the wall, after which the device is installed on it.

How to hide wires

Even before you hang the device on the wall, you need to think about how you can hide the wires. If the wall is made of drywall, you can make a cable channel in it with your own hands. To do this, holes are cut in the wall behind the device into which the cables will be led out. The second hole must be cut at the bottom of the wall, where the cable will be led into the baseboard. The next option is to make a cable channel on the wall surface. It can be painted in the same color as the wall, so that it is almost invisible, or, on the contrary, make it contrast, decorate it with paintings. Strobit concrete wall in order to hide the cable there, it is impractical.

Modern monitors delight us with stylish design and amazing image quality, and you can place them anywhere, you just need to purchase a monitor bracket. Having decided to install such equipment on the wall, you, of course, can turn to professionals. However, if you are able to take a few measurements and screw in a couple of screws, then you can do this work yourself.

Wall mount and its types

The wall bracket is a special mount that is designed to install the device on the wall. Today in stores you can find a huge number of brands and models, but among them there are three main types of monitor brackets. Their main difference from each other is how much they allow you to change the angle of the display, which makes it possible to get rid of glare. Before attaching the equipment, you need to make sure that the wall bracket you have is suitable for this particular model. The most common standard today is VESA.

There are several basic types of monitor mounting on the wall:

• hard fastener;
• inclined fastener;
• swivel mount.

Rigid fasteners allow you to hang the device on the wall at a distance of several centimeters from it. This monitor wall bracket does not have any adjustment function. After installation, you will no longer be able to rotate or tilt the device. In this regard, it is best to mount it on such fasteners at eye level. The main advantages of such a holder are reliability and low price.

The tilting monitor arm allows you to mount the display above eye level, allowing you to change the angle depending on the situation. Different manufacturers of brackets may have different angles of inclination, but the average is about 10-20 degrees. In this case, the monitor is mounted on the wall at a distance of 10-15 cm from it.

The swivel mount allows you to tilt, rotate or move the monitor as you like. This option is the most functional. But the cost of such a bracket is several times the above models. Please refer to the specifications of the bracket for size and weight limitations of the monitor. Based on this, you will be able to choose the best ratio of performance and cost for yourself.

Bracket placement height

Many people mount the monitor too high on the wall, which can cause discomfort when viewing and pain in the neck due to the awkward position of the body. Most experts advise placing such a technique at eye level. Of course, there is no exact value at what height to hang the device. The optimal height of the location of such a unit depends on its size and the area of ​​\u200b\u200byour room. In a spacious room, the display can be positioned higher than in a small one. It is best to personally test different options.

When choosing the optimal location for the monitor, you should pay attention to the strength of the wall. It is not difficult to install the bracket on a wall made of concrete, wood or brick, but if the wall is finished with plasterboard, then you will not be able to do without special devices and certain experience. In this regard, it is not recommended to install monitors weighing more than 30 kg on such a design, and if installation cannot be avoided, then special butterflies must be used, and the bracket should be attached to the base of the supporting profiles.

No less important are the climatic features of the object. Everyone knows that the quality of any device is highly dependent on external factors. Therefore, when choosing a location for installing the monitor holder, consider the following factors:

• do not hang the monitor in rooms with high humidity or in an area of ​​strong exposure to sunlight and heat;
• if the monitor is to be installed in some limited space, such as a niche, it is necessary to ensure constant air exchange.

Once you've decided on a location, take masking tape and mark the location of the monitor on the wall surface with your own hands. For good air exchange around the perimeter of the monitor, it is necessary to leave free gaps of at least 20 cm.

Bracket mounting process

As a rule, the wall bracket for mounting the monitor consists of two parts:

• plate, which is attached directly to the wall;
• fastener that is installed on the monitor.

The wall bracket is attached to the monitor with special screws. The holes intended for them are located on the back of the monitor and are sometimes covered with plastic plugs. Measure the gaps between the screwed fasteners and the edges of the monitor. Using this data, you can calculate and mark the location of the plate, and then drill holes in the wall. Using dowels, you will need to screw the plate to the wall, then hang the monitor and bracket on it, then both parts will be fastened.

Homemade fasteners

If you want to save some money on buying a monitor holder, you can make it yourself. To do this, you will need an asymmetric duralumin profile, M4 screws, dowels and 20x4 self-tapping screws. Measure the distance between the holes on the back of the monitor. Then cut two guides from the profile. The finished rails are carefully attached with M4 screws to the back of the device.

At this point, the first stage of work can be considered completed. You just need to attach the monitor to the wall. To do this, you will need a furniture board, to which the two remaining guides from the profile are attached. With the help of dowels, the furniture board is attached to the wall, after which the device is installed on it.

How to hide wires

Even before you hang the device on the wall, you need to think about how you can hide the wires. If the wall is made of drywall, you can make a cable channel in it with your own hands. To do this, holes are cut in the wall behind the device into which the cables will be led out. The second hole must be cut at the bottom of the wall, where the cable will be led into the baseboard. The next option is to make a cable channel on the wall surface. It can be painted in the same color as the wall, so that it is almost invisible, or, on the contrary, make it contrast, decorate it with paintings. Chasing a concrete wall in order to hide the cable there is not practical.

If you do not like the outdoor cable channel, you can hide the wires in drywall construction. It can be made in the form of a niche or ledge. To provide natural ventilation the niche should be spacious. Wires and cables from the monitor are hidden in holes pre-cut in the walls of the niche. The drywall ledge looks a little better. Firstly, the monitor is guaranteed to be well ventilated, and secondly, shelves can be made on the sides of the monitor.

TV on the wall: how to hang without a bracket or do it yourself?

Televisions are now very often hung on the wall. So they do not interfere, for them it is not necessary to specially put bedside tables or coasters. These devices can be attached using a bracket. But this is not the only way. In some cases, they do without such a unit. Why buy expensive design if you can manage on your own? Find out how to hang your TV on the wall without buying bulky frames, which monitor is right for it, how to hide the wires so that everything looks nice and tidy.

For convenience, TVs are often hung on the wall.

In this case, it is necessary to take into account the weight of the screen, the place where it will be located, the material on which it is to be fixed. Not all displays can be installed this way. Massive products still need some kind of “foundation”.

What type of TV can be hung without a bracket?

Before you hang the TV on the wall without a bracket, you need to find out which monitors, in principle, can be mounted without proper "support". If your technique does not meet the requirements listed below, it is better not to risk it and purchase a suitable frame. Then there will be no questions whether the screen is securely held, whether the wires are bent, whether it is too close to the wall.

Here are the characteristics of displays that can be fixed without support:

• Only "flat" TVs are suitable - liquid crystal (LCD or LED), plasma (Plasma). CRT monitors ("pot-bellied") cannot be installed this way - they need a frame with a shelf.
• All connectors and cords must be located either on the sides of the device or on the front. If they are on the back panel, after installing the equipment, nothing can be connected to them.
• To decide how to attach the TV to the wall, you need to look at what it is made of. Do not screw a massive unit onto a fragile base. Unfortunately, it is impossible to immediately determine how much weight the material will withstand. But if you see that the wall is unreliable, it is better not to risk it.
• There should be screw slots on the monitor case.
• It is desirable that the documentation for the screen indicate that it can be hung. Some models are designed to stand on a firm and level support. And when working "in the air" they may experience problems.
• It is better not to mount large displays without a bracket. The instructions for the frame always indicate the weight that it can withstand. BUT homemade units such accuracy cannot be achieved. If a small TV comes out to hang without problems, then a massive one can fall, breaking the mount and tearing out the wires.

How to choose a place for a TV?

A fixed monitor can no longer be moved or tilted anywhere. Therefore, you need to choose a place where it is most convenient for you to watch movies. The screen should be located at a certain distance from your eyes. It depends on the size of the display and the type of picture that the TV is broadcasting (analogue format, digital format, Full HD). If you are thinking about how to hang a TV on the wall, first find out its diagonal.

To enjoy TV programs on a 32-inch screen, it should be installed about two meters from a hypothetical viewer. For a 50-inch screen, this distance is already three meters.

However, to a greater extent, you should focus on your feelings. Sit where you plan to watch a movie. Imagine that you have a TV in front of you. It should be at the same level with the eyes. So that you don't have to tilt your head.

In editing, in addition to subjective, there are also objective aspects.

• TV should not be installed where they pass electric wires. It is better to find out in advance where they are, so as not to accidentally stumble upon them when drilling. There are special devices for this: metal detectors, indicators and signaling devices.
• If you decide to "hide" the screen in a deep niche, between wall panels or in a closet, give up this idea. The device will overheat.
• Hang the monitor in an open area. Do not "clamp" it between the shelves. It is not necessary to mount it on a completely empty wall. But there must be some gap.
• Install the product on high-quality and durable walls that do not crumble, fall apart, or rot. So that the screwed-in self-tapping screw does not fall out after a while.
• It is better to mount the display near the outlet. This will make it easier to hide the wires.

wall mount

If you want to figure out how to fix the TV on the wall without a bracket, it will be very easy to do. You won't need any fasteners other than screws. On one condition: you are going to install a display with a diagonal of less than 24 inches. It can be fixed like a photo frame. Just hanging on the wall.

The device in which this type of fastening is available is equipped with “ear” grooves. The instructions for it should indicate which self-tapping screws to use. Perhaps they are even included in the package. This should be checked with the seller. List of suitable screws for different materials is in the next section.

With such an installation, it will not be possible to hide the wires behind the monitor. He will be too close to the wall.

If the documentation does not say that the monitor can be fixed in this way, you should not try. This may cause problems with the device.

Fastening with a support

There should be some distance between the screen and the wall (unless otherwise indicated in the instructions). It must not be screwed close to the surface. He needs space for ventilation. You have to make a mount. However, many monitors have holes that allow mounting without a bracket. The following tips will work for any installation method.

Before hanging the TV on the wall, find out what it is made of. It depends on what parts to use, and how heavy units can be fixed.

• Concrete, brick. Most the best way(if they don't crumble). Dowels for concrete with a size of 50 mm or more must be screwed into them. The material will withstand even bulky products. But the wall should be thick and not hollow.
• Wood. Installation is possible if it good quality. Without large cracks, rot and internal voids. For fasteners, dowels for wood with a size of 30 mm or more are used.
• Drywall. Under heavy loads, it will bend. You can fix the screen not on the sheets themselves, but on metal guides. Then the design will be more reliable. But installing large TVs is still not worth it. Butterfly dowels are used. When screwed in, they will “open up” with reverse side sheet of drywall and due to this they will not fall out.

You can independently assemble the mount from improvised means. Suitable, for example, parts that you have left after repairing or assembling furniture. Suitable equipment can also be purchased at specialized stores.

The frame consists of two parts: one is screwed to the wall, the other to the TV. The heavier the monitor, the stronger the mount needs to be. Designs may vary depending on your needs. You can make a gutter to hide the wires, create some decorative element, add something from yourself.

Here, for example, is a support for a small screen:

1. Take a furniture "tire" wooden block and anchor plates for windows.
2. Drill holes in the "tire" and bar. Pre-measure the distance between future holes so that the parts can be attached to each other.
3. Screw the “tire” to the bar with self-tapping screws.
4. After that, screw the bar with the "tire" to the wall.
5. First, mark where the holes will be located. Use building level to keep the frame straight.
6. Drill holes in the wall and drive dowels into them.
7. Drill holes in the bar.
8. Screw the bar to the wall by screwing the screws into the dowels. Use a screwdriver. You can't do it with a regular screwdriver.
9. Fix the anchor plates to the back of the TV with screws. They can be cut with a grinder if they do not fit.
10. After that, attach the screen to the bar with the "tire". This is done using hooks on the anchor plate.

So you can hang only a light TV. This mount will not withstand heavy loads.

Finding out exactly what dimensions the created frame is designed for is not so simple. On the brackets they usually write Weight Limit monitor. But a do-it-yourself unit will have to be checked "in the field" conditions.

How to hide wires?

Here's how to hide the wires from the TV on the wall:

• The most obvious option is right behind the monitor. If the outlet is nearby, just place the cables behind the screen. Just make sure they don't kink or twist anywhere. Only a small piece with a fork will peek out.
• You can drill a channel right into the wall. But it makes sense to do if you are still undergoing repairs.
• If you have drywall wall, it is better to hide the wires in it.
• Decorative tricks. It's more of a disguise than a cover-up. You can turn the cable into part of the interior. For example, glue petals and flowers to it so that it looks like a stem. Or make it an element of some design composition.
• Moldings, or cable channels. Hollow "tubes" that are attached to the wall. They contain all the wiring. They can be subtle or beautiful.

The instructions for the TV usually indicate available methods installation. You can get specific information from the seller or manufacturer. When buying a monitor, ask if it can be hung on the wall without a bracket, and if it is worth buying any additional parts. If you have never worked installation work, it is better to turn to professionals.

NastroyVse.ru

How to fix the TV on the wall

No home is complete without a TV. So nice in the evening after work, with a cup of tea or a glass of wine, relax on the sofa in front of the TV hanging on the wall. After all, this option for placing a TV does not require a lot of space and it is much more convenient to watch it than if it were standing on a cabinet or coffee table. But how to attach a TV? Let's figure it out.

How to choose the right place on the wall for the TV

When choosing a place for a TV, you should take care of the safety and convenience when watching it. Therefore, you should use following rules by monitor location.

Hanging the TV, you need to hide the wires and cables

• Choice of part of the room for the TV. It all depends on the arrangement of your furniture and the location of the windows. Sit in the place where you plan to view and choose the most comfortable point for your eyes. Do not forget to take into account the dimensions of the TV panel.

Advice. Do not place the TV in front of windows. Glare and reflections on the screen will not let you relax.

• Convenient height. The optimal height is at eye level. Therefore, you should also consider the audience that will watch TV with you. You can hang it a little lower or higher, it will depend on the characteristics of the room. For example, a panel with an impressive diagonal should be hung just above your eyes, and if you prefer to watch TV on the floor, lower it lower.
• Wires and cable. Ugly if all the wires just hang out from under the TV. They need to be hidden. It’s good if during the repair you thought of everything and brought the outlet and cable directly behind the TV. Otherwise, use a cable box and decorate it to match the style of the room.

Advice. When repairing, it is desirable to place the unit for 4-6 outlets at a height of 30 cm from the floor. Today, technology does not stand still, and such sockets will certainly come in handy.

• How to attach a monitor to a wall. Basically, three methods are used: a bracket, without a bracket, and mounting the TV to the ceiling.

TV Mounting Methods

Mounting with a bracket. Bracket translated from German language- holder. This device is used to fix objects on a vertical surface: the device will help to hang the TV on the wall.

Today, there are many brackets in stores and they are divided according to some criteria:

• inclined - suitable for small TVs up to 26 inches;
• movable - used to mount a flat monitor with a diagonal of 13-26 inches.

Movable TV mount

The holder is equipped with a swivel lever, thanks to which you can change the angles of inclination to the sides and up and down;

• low profile - designed for a maximum of 40 inch TVs;
• adapter - adds width, supports a panel no larger than 65 inches;
• articulated structures - with their help, you can turn the TV in any direction.

TV mount without bracket. This method is used when it is not possible to hang the monitor on the wall. A special frame is used here, on which the TV will then be hung.

Ceiling option. This is the same bracket, it is simply fixed to the ceiling. Before you purchase such a pendant mount, you need to determine what kind of finish you have on the ceiling, and how high the ceilings are.

How to attach a TV to the wall with your own hands using a bracket

by the most in a simple way to hang the TV on the wall is to buy a bracket for this. Having decided on a TV mount, we can proceed with its installation using the following tools:

• screwdriver;
• roulette;
• screws.

1. We start by attaching the TV to the bracket plate.
2. We try on the wall and make marks at the attachment points.
3. We make holes according to the marks.
4. We attach the structure to the wall and attach it.

With a minimum of effort on your part, your family will be able to get together to watch interesting films.

How to attach a TV to the wall with your own hands without a bracket

Need the following tools:

• electric drill;
• screwdriver;
• roulette;
• screws or dowels, depending on the material of the wall;
• hammer.

How to mount a TV without a bracket

Take, for example, a TV with mounting holes spaced 20 cm apart both in width and height. For such a monitor, you will need a perforated plate 24 x 24, you can take more.

1. Using a tape measure, we mark a place on the wall for mounting the TV.
2. We make holes in the wall according to the marks.
3. We drill holes in the plate, identical to the holes on the back of the monitor.
4. We fasten the plate to the TV with 4 bolts (comes with the TV).
5. We attach the plate to the wall and fix it with dowels.

The work is finished, you can enjoy watching TV programs.

How to attach a do-it-yourself ceiling bracket

Tools you can't do without:

• electric drill;
• drill;
• screwdriver;
• roulette;
• dowel;
• hammer.

Mounting scheme ceiling bracket

Having collected the above tools, you can proceed with the installation work.

1. We make a mark on the ceiling and drill holes for attaching the bracket rods.
2. We put the rods to the holes and fix them with dowels.
3. We fix the removable part of the bracket with bolts on the back of the monitor.
4. We connect both parts. We connect the part with the already fixed TV to the bar and fix the connected parts.
5. We finish the work by installing protective decorative caps.

This is one of available ways attach the TV to the ceiling. The whole design looks original and gives the room a sense of spaciousness.

For safety and ease of installation of the TV, you need to use these tips experienced professionals:

• 1/8 inch drills are best for installing the structure. This diameter is smaller than the mounting screws, so they will sit close.
• Do not hang TV monitors that weigh more than 30 kg on plasterboard walls.
• TVs that have a weight of more than 20 kg, and their width exceeds 1.5 m, need to be hung together, it is difficult for one to cope with this task.
• Cables should only be connected after the installation has been completed.
• To avoid breaking and burning the power cable, make sure that it is neither bent nor taut.

Several outlets must be placed near the TV

• Control the work process so that when drilling, you do not get into the electrical wiring hidden in the wall. Check the technical plan of the house or apartment where your wiring is located.
• For fixing the above structures, use specially designed dowels of different sizes.

The screen, which can be hung from the ceiling or on the wall, solves many problems. With the help of such systems it is easy to hide the cosmetic defects that you have in your apartment. This structure saves a lot of space and looks very impressive. In addition, a hanging TV can always be interestingly beaten with decor, while creating an emphasis on its presence in the room. Thanks to modern metal structures that help to hold the TV, you can set the tone for the whole room and bring to life the most daring and interesting design solutions.

How to choose a TV bracket: video

How to hang a TV: photo

The monitor does not have a standard VESA bracket mount, and the monitor needs to be hung on the wall? No problem - we'll do it ourselves!

For many years, the excellent Samsung T220 monitor has served me faithfully. I bought it when large widescreen monitors were just starting to spread. A 22″ monitor with a 16:10 aspect ratio with a beautiful picture, unattainable by many modern monitors. Everything would be fine, but now it became necessary to hang the monitor on the wall, and this monitor model does not have a standard VESA mount for mounting on a bracket.

Unfortunately, I did not take photos of how it was, so I'll just attach the images that I found on the net.

The task is to disassemble the monitor, make holes, install the mounting screws, assemble the monitor and screw the mounting pad from the bracket to the screws.

To install the monitor on the wall, an inexpensive, but convenient and reliable bracket was purchased. Holder LCDS-5039.

So, we disassemble the monitor. It is not difficult to do this - we unscrew the two self-tapping screws at the bottom of the monitor, after unhooking the monitor stand, and carefully remove the back cover (it is fastened with latches). I did not record these operations.

We fasten the mounting pad from the bracket. The assembly site smiles at you. :)

This is what the fixture looks like from the inside. To distribute the load, I used enlarged washers on both sides.

And this is what the disassembled monitor looks like. Display, electronics and standard stand.

We install the back cover in place, snap it tightly and do not forget about the two self-tapping screws at the bottom.

All connectors on the rear panel are closed with a cover (not in the photo). True, I didn’t return it to this place — I don’t see the point. Next, the bracket itself and installing it on the monitor (how it will look).

The next step is marking the holes on the wall, drilling holes and installing the bracket. I must say that the walls in our house are terrible - voids and other delights. I drilled two holes out of three well and reliably, and the third fell into the void. But everything was securely held on two dowels. True, I realized that I hung the monitor a little high and the next day I decided to lower it 5 cm lower. I had to tinker. I re-drilled the holes a few times, all of them came across voids. Postponed for a day. And today, instead of dowels 6 * 80, I used the “eight” (I don’t know the length, 12 centimeters). Achieved reliability and still left. Now we need to find wallpaper scraps to seal the holes. However, nothing is visible behind the monitor. =)

Here's what happened.

And here's how it was. Sorry for the quality of the photo - taken with a phone.

As you can see, free workspace. Now not two, but three cats will fit on the table. =)

Mounting the monitor on the wall - do it yourself

Important questions you will have to answer yourself before you hang the monitor on the wall without a bracket. Lack of shelves and other additional structures supporting massive technique is not always justified. And the TV to be repaired is easier to repair if it is not suspended. It is better to entrust the matter to a specialist, if not, video materials and recordings of master classes that abound on Internet portals will come to the rescue. For the rest, you will have to rely on yourself, the strength of the wall and the reliability of auxiliary structures.

How to hang a monitor on a wall without a bracket: “reinforcement from the rear” will come in handy.

How to hang a monitor on the wall: what is taken into account?

Initially determined with the type of TV. CRT electronic "creations" are unlikely to look harmoniously on the wall, which, most likely, will not have to be tested for strength for a long time - there is a high probability of tearing out fasteners. Monitor installation features:

This method is suitable for LCD and plasma models.

· Given the maximum proximity of the equipment to the wall, it will have to be connected if the connectors are located on the sides.

・Need to pick optimal location for the monitor. It makes no sense to hang it under the ceiling, similarly - and close to the floor (then it is more convenient to install a shelf or bracket). The ideal height is at the eye level of a person who watches TV while sitting.

An important detail: the wall chosen for mounting must be "in the possession" of the owner of the TV, since it will have to be strengthened from the back.

Is it right to hang the monitor on the wall?

There are no questions about the thickness of the wall (lucky if it is brick), they get bolts of the appropriate length (to pass through the wall and an additional metal plate, reach the monitor).

Important! Despite the harmlessness to the vision of modern screens, they are suspended at a calculated length - it is calculated based on the length of the diagonal of the equipment, multiplied by three. Install the TV according to the scheme:

1. Purchase a perforated plate, which will be fixed for strength on the back of the wall. It should exceed the perimeter of the TV itself by 4 cm.