The hallway will be inferior if it does not have a solid spacious closet. It is not necessary to buy it at all, since the manufacturing process is quite simple.
Spacious closet in the hallway niche
The advantages of this option:
The main thing is that the furniture in the hallway should be roomy, compact, neat, not pretentious.
Details to consider when designing.
Furniture fittings for the wardrobe in the hallway
To assemble a wardrobe in the hallway with your own hands, the following tools and accessories are prepared in advance:
DIY cabinet assembly tool
It is better to take inexpensive materials that are easy to process. For example, even experienced manufacturers will not undertake to make furniture from solid wood.
Chipboard cabinet with mirrored door
Spacious eco-friendly plywood wardrobe
Sliding wardrobe and cabinet made of MDF in the hallway
Fiberboard for the back wall of the cabinet in the hallway
Wooden beam for the frame of a homemade cabinet
Edged board (pine)
Homemade drywall wardrobe in the hallway
The most responsible approach is to take measurements. If a miscalculation is allowed, all subsequent work will be difficult or nothing will work out at all. There are various ready-made options with suitable sizes. If the finished drawings are not suitable, and the drawing skills are weak, you need to attract a specialist for this stage, who will think over the project with the right dimensions. Cutting materials and edging the end parts is better in a store that sells building material. Store services are inexpensive, but it saves a lot of time.
This model belongs to the built-in ones, it is easier to manufacture, since the parts do not need to be calculated and cut out. The complexity of this option is that it is necessary to take into account the features of walls and floors.
The ideal solution for such furniture would be a niche with a sliding system, equipped with several shelves, a crossbar for hangers. The installation of the wings in this case is the same as for the interior doors (the wall and the floor are involved).
Very often, a closet is made in the corner of the room. This model does not have one side and back wall (and in some cases there is no floor and ceiling).
The base consists of a wooden frame, which consists of a pair of frames (front and side), assembled on self-tapping screws or nails. If the project provides for the arrangement of shelves and partitions, cross rails must be fixed to the frames in the designated places.
Mark the walls, floor, ceiling in places where the frame will be installed, drill holes for the fasteners. It is recommended to mark the places of the paper clip as well.
We make markings for shelves, install corners
Fasten the front frame to the wall and ceiling with dowels. Check its verticality using a level.
We lay and fasten the shelves on the corners, install the vertical panel to the shelves inside the cabinet
Install the side frame.
In the resulting niche, wooden slats are attached to the walls, designed for shelves (cut shelves from plywood or chipboard). You can not fix the shelves by laying them on the slats or fix them with nails.
On top of our construction, we lay a horizontal shelf according to the level
The side is sheathed with drywall or laminated chipboard. Drywall is pasted over or painted. The side part, in which the crossbar with hangers will be located, must be strong (chipboard, plywood, but not drywall).
We prepare panels for the front side of the cabinet
Attaching the bottom and top panels
The final stage is the installation of sliding doors. Top and bottom rails are mounted respectively on the ceiling and on the floor.
Installing door rails
Here it is very important to observe the exact dimensions. First, they try to install the layout of the future door. Take any part whose height is the same as that of the door and install it inside the top rail. Check the verticality value and mark the area where the lower guide will be attached. The door must first be inserted by slightly pressing on the upper rollers, and then into the lower tire. To adjust the position of the door leaf, adjusting screws are used. A properly installed door moves smoothly, without hindrance.
We insert the doors into the guides, snap the latches and adjust the mechanisms in the roller systems
The above example is suitable for a simple small size structure consisting of two halves. With a good hallway area, it is possible to manufacture a more spacious model. Then the frame of the bars will not work. It is better to make a base from chipboard, and “fasten” its elements with the help of a common floor and ceiling. This method will allow you to place in a niche, in addition to shelves and a bar for hangers, also boxes for small items and other details.
Such a product will be assembled as a designer for dowels and confirmations. For this fitting, you must first drill holes. All this must be done very carefully and patiently. All fasteners for corners are kept in a clamp for a day.
Built-in two-door wardrobe in the hallway
It will be easy to make a corner module with your own hands. For stability, modules are often made of durable solid materials (chipboard, plywood). These products come in several forms:
Basic configurations of corner cabinets
The most suitable for the hallway is five-walled.
Built-in five-wall corner cabinet
Detailed assembly diagram of the corner cabinet
Instructions for self-assembly of a corner cabinet
Convenient do-it-yourself shoe rack
This is the easiest process, because everything that is needed in the work is sold by the building materials store.
The design includes: an outer frame, several shelves with partitions. The width of the structure depends on the maximum shoe size, and the height depends on the number of shelves.
Addition of facades and clearances of cabinets for shoes
A good solution would be to combine a shoe cabinet with dresser elements. Or place it in a closet or corner wardrobe, which have open facades.
There is a lot of information on the Internet about how to make a closet in the hallway with your own hands. Therefore, by examining all the available data, the most suitable model can be successfully constructed.
The first thing that guests who enter the house see is, of course, the entrance hall. It can be safely called the "calling card" of the apartment. Therefore, the hallway in the house should be not only beautiful, but also comfortable. For this, various furniture is placed here. In particular, there is often a wardrobe, a hanger, a mirror, a cabinet for shoes and a chest of drawers. In addition, it will not be superfluous to put furniture for sitting here. It can be a bench, a sofa, an ottoman. In general, how the entrance hall will be equipped depends not only on the size of the room, but also on the owner himself. Next, we will tell you how to make a hallway with your own hands.
With a small size of the hallway, it will be more convenient to choose a few medium-sized items. It can be a shelf for hats, a nightstand for shoes, a small mirror and a hanger. In a small square-shaped corridor, a set of cabinet furniture will look good, which consists of a cabinet for shoes, a chest of drawers with a mirror and a wardrobe. In large rooms, you can place almost any furniture. In general, there are a lot of options for hallways.
As a closet for the hallway, perhaps the best fit wardrobe, which is distinguished by functionality and spaciousness. It can be placed even in a small room. It can store not only outerwear, but also hats, shoes and various accessories. For very small rooms, it is best to install built-in wardrobes. With the help of them you can save space and fit in one place all the shelves and hangers you need for clothes.
You can use cabinets with a door, but they require more space in the room. They may have one or two wings. By the way, sashes are usually equipped with various useful devices. It can be a compartment for storing gloves, an umbrella stand, small shelves. In any hallway often put a mirror. And most often it is large enough so that a person can see himself in full growth. In addition, this piece of furniture allows you to visually make the space wider. There are three main mirror designs for the hallway. So, it can simply hang on the wall, be framed or built into the cabinet doors.
Every hallway needs a shoe rack. As it, you can use a galoshka with built-in or open shelves or a simple cabinet. It is usually equipped with hinged, folding or sliding doors. Height is both high and low. The most convenient option can be called a bedside table, which consists of several sections located one above the other. The shoe rack in it is located inside on the doors.
The following requirements are imposed on the closet in the hallway:
Work order:
The manufacture of such a bedside table is in many ways similar to the process of manufacturing a single-door cabinet. The frame blank is also first marked and sawn out. On the sides, cuts should be made that will allow the cabinet to stand close to the wall. Next, you need to make a plank of plywood and a shelf. In size, they are the same as in a single cabinet.
The bedside table usually has two compartments. One of them is about a quarter of the size of the structure in width, and in height it is the same as the height of the entire pedestal. The second branch occupies the remainder. At the same time, it is divided into two more parts using a horizontal shelf.
Now the nightstand can be assembled by gluing and pre-installing dowels. After that, it must be fastened with self-tapping screws. It remains to cut and install the doors in place.
To make this piece of furniture, you will need several boards. The production variant with two blocks is described below:
It is not difficult to make such a piece of furniture. To do this, you need a furniture board, from which you should cut out a wall, a bottom, a front plate, a cover and two back walls (if necessary, a part under the plinth is cut out on them). This is necessary so that the cabinet stands close to the wall.
Work order:
Below is an example of assembling a cabinet that can be placed even in the hallway of a small "Khrushchev". There will be a gap at the bottom of the structure, which is obtained due to the installation of furniture legs 55 mm high. They will be attached to the cabinet with 4x16 self-tapping screws. That's all there is to say about these supports. Next, the assembly of the cabinet body itself will be considered. Let's start with the dimensions of the parts.
In the manufacture of a wardrobe for the hallway as a material, you can use:
The manufacturing process of the facade will not be considered here. It is envisaged that a custom version will be used, consisting of an aluminum frame with a sample for three hinges, and a mirror is inserted into this frame.
By the way, you can build a simpler version, which is also cheaper. So, a mirror is glued onto a sheet of chipboard with the help of special glue. It turns out the facade, which will be more massive and heavier than the previous version. In this case, it will require at least 4 loops. In addition, the cabinet itself will need to be attached to the wall for reliability. Otherwise, it may simply collapse when opening the doors. Therefore, decide for yourself which facade is preferable for you.
You will need the following chipboard sheets to assemble the structure:
Before making a closet for the hallway, you should make sure that when installed in place, it will not cover sockets, switches, and other similar places. The design itself is easy to assemble. To do this, you will need the following tools:
In addition, you will need the following specialized fittings:
To prevent the fasteners from matching, the shelf inside the cabinet should be placed 35 mm higher than the open part.
Screeds are made for confirmations. Under them, you first need to drill both into the end face of the part and into the plane. Standard furniture fasteners are 5 by 73 mm. Holes in the plane should be 8.5 mm in diameter and at the same time through. All markup is done depending on the number of design details. They may well be sidewalls, facades or the back of the open part.
Hardboard can be fixed with self-tapping screws or nailed. The first method is more suitable if you have free time. The second should be used if there is not much time. The most important thing in both cases is to observe the rectangularity of the structure. Otherwise, the facades will turn out to be outwardly unattractive. In addition, they will not be able to close normally. The above recommendations on how to make a hallway are actually nothing more than an example. You yourself have the right to decide what and how to design. This applies not only to the quantity and composition of materials, but also to other aspects.
The entrance hall creates the first impression of the interior of the house, it should have a beautiful design, be comfortable. It contains furniture for various purposes: a wardrobe, a mirror, a bedside table, a hanger, a chest of drawers. It is also a good idea to place seating furniture: a bench, an armchair, they will complement the design. So, a do-it-yourself entrance hall allows you to choose any design as in the photo that the owner of the house wishes.
When creating a hallway, you can use drawings, diagrams, photos that can be found on the Internet or create your own drawings. Creating furniture will be easier if you use blueprints. The design of the hallway is not the last place in the interior of the whole house. Wood furniture photo will look good. Complement the design with wooden floors or laminate.
It is quite possible to create any of the elements of the hallway with your own hands.
Manufacturing steps:
To prevent cracks in plywood, holes must be made before screwing in the screws. It remains to make only the front of the drawer. We make the upper part, the lid and fasten it to the body with furniture edges.
The manufacturing process of a bedside table with two doors is similar to a single door bedside table. First, a frame is made, we mark it, then we cut it out. Slots are made on the sides so that the bedside table fits snugly against the wall. Next, cut out the plank for the plywood shelf. The dimensions are the same with a single-leaf pedestal.
Most often there are several departments. One department occupies a quarter of the entire structure in width, and in height the whole place. The rest of the place is occupied by the second division. It is divided into two parts by a horizontal shelf.
Drawing of a double cabinet for the hallwayAll parts of wood are fastened together, they are pre-glued and dowels are installed, as shown in the photo. After all parts are fixed with screws. Next, we cut out the doors and install them so that there is no deviation when closing.
In the manufacture of hangers, we select several boards of wood. Boards must be the same length. We describe the option of how to make a hanger from blocks, if desired, you can make a hanger with a large number of blocks:
There is nothing complicated in the production of a pencil case. You need to purchase a furniture board, cut out of it: a wall, a bottom, a front part, a cover, two back walls, they cut out a place for a plinth so that the cabinet fits snugly against the wall.
Work plan:
Consider how to make a closet that can be placed even in the smallest hallway design. It will be mounted on legs that are attached to it with self-tapping screws, they have a height of 55 cm, the dimensions of the self-tapping screws are 4 × 16, so a gap is formed from below. No more information is needed about these supports, now let's pay attention to the assembly. First, let's define the dimensions of the parts.
Materials for creation:
The facade is made to order, it is made of an aluminum frame, fastened with three hinges, a photo mirror is fixed in the frame.
This is a more expensive option, but you can use a more budgetary one. The mirror can be glued to a chipboard sheet using special photo glue. It will turn out a bulky and heavy facade, relative to the custom version. For it, you need to purchase at least 4 hinges, it is better to attach the cabinet to the wall, so it will be more reliable. Otherwise, it will fall when the door opens. Therefore, it is worth deciding on the facade option yourself.
To assemble the frame, you need to purchase chipboard sheets of the following sizes:
Measurements in millimeters.
Before making a closet, you need to choose a place where places that are often used will not be closed. The frame is easy to put together.
When collecting, tools are used:
Specialized fittings:
To match the fasteners, it is better to place the inner shelf 35 mm higher. They produce screeds for confirmations. Under them, details are drilled into the end and into the plane. Fasteners are standard 5 by 73 mm. In the plane of the hole through the diameter of 8.5 mm. The markup is placed depending on the number of parts. Such as sidewalls, facades, back of the open part.
Orgali are fixed with screws or nailed. If there is enough free time, then it is better to choose the first method. The second method is better to choose if you do not have a large margin of time. In the first and second options, it is important to observe that the structure remains rectangular. If this requirement is not met, then the facades will look unattractive and will not be able to close well.
The place behind the door is ideal for placing a wardrobe. By installing it, the wall will be protected from damage that a doorknob can do. You will need an inch board, a layer that is pre-pasted with wallpaper and varnished or painted. Lacquer is used if the wallpaper is suitable for the design of the room. Paper for pasting is used to prevent warping of the board during operation.
Cut out blanks similar in size to the door:
The parts are connected with self-tapping screws, with large caps-washers. Shelves are attached to the wall using corners or rails. The rack is attached to the side with corners, or with a hidden mount.
A canopy-loop is installed at the back to the end, a self-tapping screw is screwed into the wall and a loop with a sidewall is put on it.
Attaching doors to cabinetHidden fasteners can be used for shelves. If the cabinet is fixed with hidden fasteners, then if necessary it can be easily removed. How to make your entrance hall, and what design to choose, only the owner of the house can decide, and whether to use the recommendations given in this article or not, this is only his decision.
A mandatory attribute of any hallway is a comfortable, functional closet.
If you have experience in carpentry, you can make a piece of furniture with your own hands.
This will help save money and create a wardrobe that will become an interior decoration.
In addition, the entrance hall is the first room that your guests notice. And your masterpiece can become its main decoration!
Before developing a wardrobe project, it is necessary to clearly define what items it is intended for and how many things will be stored. Take into account the dimensions of the room.
The main purpose of the closet in the hallway is to store shoes and clothes, hats and even household appliances. There are the following types of wardrobes:
For one person or a small family, a one-door wardrobe is enough. The number of sections is two. The internal filling should include shelves for shoes or shoe boxes, drawers for hats and small wardrobe items, stands for hats and umbrellas. You need crossbars for hangers and hooks for everyday clothes, and a mirror is a must.
When creating a schema must be taken into account:
In large hallways there are two-door or three-door wardrobes. It is convenient to store not only seasonal shoes, hats and accessories in them, but also bed linen, towels, magazines. The width of the shelves is variable - from 40 cm or more. The height between them is from 250 to 350 mm.
Important! The greater the depth of the shelves, the greater the distance between them and vice versa.
During the drawing up of the scheme, it is necessary to take measurements of the details and draw everything on paper.
Reference. There are no set rules for scheduling. It is advisable to make a cabinet project according to ready-made drawings, which are easy to find on the Internet. And you can draw a sketch of the future product yourself, carefully considering all the details.
According to the drawings, sawing of the material will be carried out.
Circuit development sequence:
It is necessary to outline the ends for gluing the furniture edge tape, to select the fittings. Mark all dimensions on the drawing. To facilitate the task, you can use a free computer design program - for example, SweetHome 3D.
According to the selected dimensions, you need to prepare 6 important body parts:
As side panels, rear panel, bottom and cabinet lid the walls of the apartment and the floor can be used. This will help save on materials.
Important! If the walls are made of drywall, this solution is not acceptable.
The construction market offers a wide range of materials with which it is possible to implement any design solution. It is not necessary to make a cabinet from solid wood. It is expensive and difficult to process. It is better to buy practical inexpensive materials that are easy to work with.
Laminated chipboard panels- the best option for making a piece of furniture with your own hands.
Chipboard advantages:
wood boards lightweight, so do not need fittings or reinforced fasteners. A wide selection of textures will allow you to realize any design ideas.
plywood sheets strong, lightweight and dimensionally stable. The material is several times cheaper than wood.
MDF panels are analogous to chipboard, and are inferior to them in terms of fiber pattern and quality. Such furniture is less expensive. On sale there are MDF with imitation of precious woods.
Advantages:
Wood fiber boards have excellent performance. For the manufacture of load-bearing structures of the cabinet, medium or high density fiberboard is suitable.
The facade of the wardrobe can be made of wood, glass or chipboard, MDF sheets. Suitable laminated panels with a mirror or regular surface, with tinted auto film.
When choosing a material, take into account financial possibilities. If the budget allows, you can make a cabinet from natural wood. The most durable is mahogany. Alternative options are beech, Karelian birch.
You need to purchase the necessary accessories:
The number and type will depend on the number of sections, drawers in the closet.
Important. The fittings must be of high quality so that the doors do not jam.
Before starting work, it is advisable to prepare everything in advance necessary tools and inventory. Namely:
If you plan to cut the blanks for the cabinet at home, you will need an electric jigsaw.
Sawing parts is carried out according to the finished drawings. If you have experience, you can handle this yourself. But after sawing the material with a jigsaw, chips may form.
expedient turn to professionals for cutting blanks. The sheets will be cut beautifully and precisely, and there will be no jagged edges on the edges.
After cutting the parts, edging is carried out with furniture PVC tape. The edge is glued with an iron heated to a certain temperature.
Pre-marking for fasteners with maximum accuracy.
Important! The holes for the fastening elements should be located strictly in the middle of the thickness of the end of the workpiece, since the confirmations are screwed into the end.
Install the bottom and walls of the cabinet according to the scheme:
Important! To fix the cover, a screwdriver will not work. Fasteners are baited manually using pliers. Additionally, tighten with a ratchet or hex wrench.
Proceed to the installation of side shelves. They are fixed with four confirmations (2 on each side).
If the side shelf is flush with the inner shelf or bottom, confirmations cannot be used.
Fasten with dowels - wooden cylinders. They are inserted into pre-prepared recesses in the wall and pushed into the same holes in the shelf.
Assembly of doors begins with the installation of the back door. The level checks whether the cabinet is accurately exposed. The upper level is fixed by placing 2 supports and a running lower profile on it. To assemble the rear door, you will need a set of accessories:
If glass or mirror insertion is envisaged, install segments of the seal along the length of the dividing profile. When mounting parts from chipboard, a sealant is not needed.
When assembling the door, the inserts are placed on the foam with the front side so as not to damage. Glass or a mirror is installed in a horizontal dividing profile. When mounting two glasses, the sealant is placed on both sides.
The combined door is assembled using dividing profiles. A sealant is required at the joints with glass. The main door profile is fixed on both sides of the door. If it is made of chipboard, use 4x25 screws. To the connecting profile is fixed with screws using a screwdriver.
Important! One profile is fixed in a horizontal position. The second - according to the vertical arrangement of the door.
The profile handle is installed on both sides, directing the bend to the front side, controlling the tightness of the joints. If necessary, they are knocked out with a mallet and the mates are aligned along the entire length. The restrictive sealing corner of the rear door, the track roller without pins, is mounted on the side of the profile handle.
Hanging the rear door is carried out on the running profile and go to the front. Prepare the same set of fittings as for the back door. The assembly of the front door of the cabinet is carried out in the above sequence.
At the final stage, hangers and baskets are installed on the side walls. Check the functionality of the doors. They must open and close without extraneous sounds and easily.
If you need to decide on the possible design of the final result, we advise you to take a closer look at the following photos:
All stages of the process can be seen in the following video:
Thus, making a closet in the hallway with your own hands is a responsible and painstaking work that is done in stages. Choose a product design; determine the content; make measurements, draw up a diagram and drawing; buy materials; make blanks of parts and assemble the cabinet.
In contact with
Most pieces of furniture are quite simple in their design, which is quite reasonable. Cabinetmakers have been in their craft for several centuries, but the production of furniture on a mass scale began relatively recently. And up to this point, each owner of the house made tables, chairs, beds, cabinets independently.
You can do it now with your own hands. Moreover, modern tools and materials greatly facilitate this process.
The situation in the hallway does not apply to either the front or the universal, it only requires spaciousness, compactness and a neat appearance. Decorations are minimal. Well, to be honest, decorating furniture is a simple and pleasant matter.
Additional materials include drywall - for arranging built-in niches, and furniture edge - an indispensable element.
Depending on the type of furniture for the hallway, you will need various kinds of fittings:
The quantity and quality of fasteners is also selected depending on what exactly is being collected:
The set of tools is quite standard: a screwdriver, a drill, a jigsaw or a saw for wood, a key for confirmations, a mallet. If it is mounted on glue, and this is quite acceptable, then a clamp is definitely needed. To check the verticality and horizontality, you will need a square and a building level.
Photo of do-it-yourself furniture for a small hallway (after repair)
The most critical stages of self-manufacturing include sizing. If a mistake is made here, all the rest of the work will go down the drain.
The model of the closet, hallway or chest of drawers is carefully calculated. You can use the finished drawing if the dimensions are suitable for the hallway. If not, and your own experience in the drawing business is too small, it is better to contact a specialist and get a finished project for the required dimensions.
Cutting chipboard, MDF and plywood, as well as edging, are available at most stores that sell this material. This service is relatively inexpensive and saves a lot of time and effort.
Photo of a built-in wardrobe in the hallway, made by hand
Making your own is both easier and more difficult at the same time. Easier, because some details do not need to be calculated and cut out. It is more difficult, since the cabinet is “tied” to a niche, which means that the project must take into account the features of the walls and floor.
The level of "embedded" may be different. In the ideal case, this is a niche that is equipped with shelves and a bar with hangers, and a sliding system. Moreover, in this case, the sashes are mounted as an interior door - to the wall and to the floor. But much more often, built-in means a closet that occupies the corner of the room. In this case, one sidewall and back wall are missing, and often the floor and ceiling.
The described option has a small size and a fairly simple device - only two compartments. If the area of the hallway allows, you can make a much more spacious structure, but in this case it is recommended to assemble the frame from chipboard, not bars, and connect the parts with a common floor or ceiling. The latter method is easier to implement. This design allows you to install not only shelves and a bar, but drawers, lifts for clothes and so on.
Assembly in this case is done on dowels - parts with each other, and confirmations - shelves. The holes for them are drilled in advance, and then the cabinet is assembled as a designer. The work requires not so much qualification as accuracy and patience: a lot of holes are drilled, and each corner fastening must be kept in a clamp for at least a day.
The following video will tell you how to make your own built-in wardrobe in the hallway with your own hands:
The standard version of the situation in the hallway is in the form of a shelf or a stand with hooks, if there is a place for it. The main element here is, of course, the hanger.
The most popular and simplest version of it is wall-mounted. This is a shield - one-piece or consisting of vertical rails, which is fixed to the wall. A hat rack is a must. Such a stand is being built from plywood, chipboard or edged boards - at will.
Making such a model original is more than simple. To do this, boards or elements from chipboard are given an unusual shape, for example: cut out slats in the form of a picket fence and fix hooks of various shapes. No less original is the hanger, where the base is an irregularly shaped piece of wood, like a cut of a trunk, and the hooks are lacquered fragments of branches with knots.
In this video, you will learn how to assemble a wardrobe with your own hands:
And this video will help you with the assembly of a radius cabinet for the corridor:
With hooks, it is no more difficult to make than a simple wall-mounted one. But for the stability of such a design, it is usually assembled from solid material - chipboard, plywood, and not boards.
The classic model is a module of two parts, connected at a right angle, with an upper and lower rounded shelf. A rectangular shape is undesirable, since the corner visually needs to be softened. Yes, and using such a shelf is inconvenient.
If there is not enough space in the hallway, you can fix it on such a hanger by simply gluing it to one of the sidewalls.
Do-it-yourself corner wardrobe in the hallway
Photos of various options for hallways can be found in an infinite amount. Unfortunately, nothing but the appearance of the models can be judged by them. Drawings are much more informative.
If you decide to use the finished drawing, then, firstly, you need to make sure that the dimensions indicated in it are suitable for the hallway. Secondly, the working diagram indicates not only the general parameters, but also the distance between the parts, taking into account their thickness. If the material used in the manufacture differs in size, this difference must be taken into account.
The best version of the drawing is a diagram with a dimensional table, where the parameters of each part are indicated separately, and the attachment points are also marked.
Do-it-yourself drawings-photos of hallways
From chipboard
compact coupe
With a mirror
kayabaparts.ru - Entrance hall, kitchen, living room. Garden. Chairs. Bedroom