How to clean old pvc window film. How to remove protective film from plastic windows

Glad to see everyone on my blog!

After installing plastic windows, not everyone immediately removes the film from them. But in vain!

More than once I had to observe in a recently built house nearby how the tenants rub it wet rags and try to scrape it off with a scraper, because they did not immediately realize that it had to be removed immediately after the purchase.

What can I say, because many people buy apartments after the film has had time to dry tightly.

Therefore, be vigilant, read useful tips on effective cleaning methods and immediately check them in practice.

On the protective films of profiles, manufacturers write that to remove the film from metal-plastic window structures required immediately after installation. But, for a number of reasons, this requirement is often neglected.

The protective coating protects the structure from contamination that inevitably occurs during repair or construction.

For example, the film may be useful in the design of slopes, external insulation of housing, and decorative work.

In such cases, the film adhesive remains on the frames longer and hardens over time. This complicates the process of peeling off the film, and the glue itself sticks to the windows in the form of unaesthetic black spots.

How then to remove the film from plastic windows?

Useful advice!

This problem can be solved in two stages, successively applying mechanical and chemical methods.

The first will allow you to remove the film itself, while the second will deal directly with the glue.

Accordingly, to achieve the best effect, it is advisable to go through both stages. It is this approach that will allow you to effectively get rid of the problem and avoid scratches on the windows.

So, the protective coating can be safely removed with three tools:

• scraper for cleaning glass-ceramic stoves;
• industrial hair dryer (it is also acceptable to use household high power);
• school eraser.

In the first case, carefully separate the film with the sharp edge of the scraper. Due to the fact that this device is designed for glass-ceramic, the likelihood of scratches on windows is quite low. But you still need to be careful while working.

The second option is considered safer and more reliable. Hot air must be used to heat the glued surface.

It is important not to overdo it so that the film does not melt and stick to the structure tightly. Yet warm coating removed in one swift motion. If necessary, the edge can be pry off with any sharp object.

Removing the film with an eraser, at first glance, seems to be quite an exotic method. In practice, this method will require a lot of effort from you, but the PVC profile will certainly remain intact.

But to remove the film from plastic windows, the use of one mechanical way not enough.

After the physical separation of the film on window frames remains glue, which is firmly adhered to the structure. If the composition did not have time to dry well, you can do with an ordinary household rag and soapy water.

A well-dampened cloth should vigorously rub the contaminated areas. However, in some cases you will need more powerful tools. So, chemicals COSMOFEN 10 or FENOSOL showed themselves well. They are good because in addition to persistent dirt, they can also remove minor scratches.

You can also use "Nanoflex P-12" - an equipment cleaner. It is worth mentioning that the listed methods of removal protective coating suitable for all elements of window structures. The adhesive composition in them, as a rule, is used the same, which allows the use of the same tools for working with frames, double-glazed windows, window sills, and fittings.

In conclusion, we note that before removing the film from plastic windows, it is necessary to complete all construction works in the opening area. So you can keep the attractive appearance of the structures for a long time.

Naturally, with the exception of those works after which it will not be possible to physically remove the film.

source: veka.ua

Do we remove the film if we didn’t do it right away?

The frames of metal-plastic windows are protected with a special film in order to protect them from dirt, scratches and other damage during transportation and installation.

Removing the film from metal-plastic windows is extremely simple, if done in a timely manner, i.e. immediately after the windows have been installed.

If for some reason you tightened up with this, then removing the film can be a big problem. According to the instructions, the film must be removed within 10 days after the installation of metal-plastic windows.

If you increase this period to a month or two, then, most likely, nothing terrible will happen. When the film remains on the frames for 3 or more months, it will take a lot of effort to remove it.

Why does such an inconsistency arise? It turns out that the protective film consists of 2 layers and is glued to the frames with a special adhesive. Under the influence of heat and solar radiation thin inner layer the film decomposes and tightly sticks to the plastic.

To separate the surface layer of the film is not as difficult as the inner one.

Reasons that increase the adhesion of the film to the frame:

1. Action ultraviolet rays. Once the film is on the windows that are on shady side building can be removed after a few months, on the sunny side it will begin to soak into the frame in just a few days.
2. Glue quality. The lower the quality of the adhesive that holds the film, the more difficult it will become to tear it off. In the case of installing inexpensive metal-plastic windows, the possibility of encountering bad glue is higher.
3. Heat action. If the windows are installed in winter period, the film will begin to dry to the frame later. In the summer, this happens extremely quickly.

Finally, consider how to remove the film from metal-plastic windows if it was not removed in a timely manner.

• Apply building hair dryer. This the best remedy to remove the film. The main thing is to direct it to the frame, but not to the glass package, otherwise it has the ability to burst from the temperature difference. The film is heated with hot air, dissolves and is easily removed. The only problem is finding a building hair dryer. Some try to use ordinary, in turbo mode. This can be crowned with triumph only when the film is not quite firmly stuck.
• Contact a cleaning company. The bulk of such firms do a similar service, while they have the devices required for this: a building hair dryer, special scrapers and cleaners. And skill in solving similar difficulties.
• With a professional scraper for cleaning glass-ceramic plates. Such a scraper will not spoil the plastic.
• Slowly, piece by piece, picking up the edge of the film with a thin knife, blade or scraper, and then tearing it off with your hands. Cutting devices should be used as little as possible, trying to separate the film with your fingers.
• Adhesive residues can be washed off with the rough side of a sponge and bathroom detergent.
• weak solvent. When using a solvent, be extremely careful and test in an inconspicuous area first. The solvent has the ability to change the color of the plastic frames.
• Eraser. An ordinary school pencil eraser can help remove the remnants of the film.
• Rough though not wire brushed and soapy water. The method is suitable for film on the shady side.
• white spirit. Although it should not be applied on top, on pieces of film, but between film and plastic. To attain desired result it is necessary to pry off the edge of the film, pour white spirit into this place, wait a little and separate the film.
• "Cosmophen". In companies that install metal plastic windows, you can purchase a specially designed plastic cleaner - Cosmofen. Based on the degree of activity of the active drug, Cosmofen No. 5, Cosmofen No. 10 and Cosmofen No. 20 are distinguished. No. 5 is the most powerful solvent, it dissolves plastic, as a result of this, it must be used with great care. In general, let's say 2 others. These are potent and unsafe means for a person's well-being.

Often the film is not removed because the repair is delayed and you want to protect the window frames from paint, whitewash and other contaminants. This is the wrong approach, which will give rise to even more dilemmas. Much better to remove protective film, and if you need protection, stick masking tape on the frames. It won't be hard to take it off.

source: stroiportal-dnepr.com

Removing the protective film from PVC windows

We often hear questions like this:

“A year ago, plastic windows were installed in the company ****. All this time, the apartment was being renovated, and my husband and I lived with relatives.

Now, after the repair was completed, they found that the protective film that is glued to the plastic does not tear off. That is, the film that was inside the apartment came off normally, but from the side of the street it is held tightly.

How can I try to remove the film from the window? Is there any remedy?"

I have to disappoint you, I do not know of such means that can help you with 100% probability. After installing the window, the protective film must be removed immediately, otherwise it is destroyed in the sun under the action of ultraviolet radiation and melted into the plastic.

Note!

The protective film must be removed immediately, otherwise it is destroyed in the sun and melted into the plastic.

Manufacturers of plastic windows even write warnings on this film, but usually in a foreign language. In our practice, there was a case when we installed windows for the whole house for customers, and the profile from which the windows were welded lay for a long time on the street under the sun.

We were not able to remove the film from these windows, and the problem arose, of course, after all the windows were installed. As a result, we had to completely replace all the windows with new ones.

But sometimes, special cleaners can help to remove the film. We have Cosmofen plastic cleaner for sale. A very serious thing to say. Distributed specifically for window companies.

There are 3 brands of Kosmofen: Kosmofen No. 5, Kosmofen No. 10 and Kosmofen No. 20, they differ in the degree of dissolution of PVC plastic.

So Kosmofen No. 20 does not dissolve plastic at all, Kosmofen No. 10 is a weak solvent for PVC and Kosmofen No. 5 is the strongest solvent.

I think that if Cosmofen does not help you, then nothing will help you. The only way out it is either to change the windows, or to spit and forget, thank God the film is on the street and is not visible from the apartment.

source: www.okna-lider.com

How to remove film from windows after installing them

When installing plastic windows, always remember that it is necessary to remove the protective film that trims the profile for safety purposes immediately after the windows are in place and that's it. Finishing work finished.

However, real situations indicate that consumers often order PVC windows from one company of such well-known brands as KBE, PROPLEX, Veka or the eminent Rehau, and they are installed independently or with the help of other contractor companies.

In such situations, everyone completely forgets to remove the notorious protective film on the profile, which, under the influence of sunlight, sticks to the window so strongly that it is almost impossible to remove it.

In which case, it will be possible to make claims about the quality of the work performed, and its employees will be required to take care of removing the film from the outside of the profile.

On the windows, the film prevents scratches, both during their installation and during installation. Experts in this field recommend getting rid of such a harmful film within 10 days after the windows have been exposed to the sun.

If time is lost and protective layer not filmed, do not be self-willed, but listen to useful tips, proven by time and practice. Many make a gross mistake when trying to remove the film with a solvent. So the film will remain on the windows, and the profile can be hopelessly damaged.

Proceed with extreme caution, as high heat the entire profile may be damaged.

An equally effective tool for removing film from a window will be the use of a special scraper used during cleaning. hobs and ceramic tiles.

You can safely work with a scraper, because it does not damage plastic surface.

Try very carefully to pick up the edges of the adhered film with a scraper and remove it piece by piece from the window. If possible, work only with your fingers, as even a safe scraper can leave scratches on the PVC profile.

When finished, thoroughly wipe off the remaining adhesive with warm soapy water. If the glue cannot be cleaned with soapy water, then use the special Cosmofen 10 cleaner.

It is important that it not only removes adhesive residue from the film, but also largely masks the resulting small cracks. From improvised means, an ordinary eraser from the school desk helps well, it perfectly rolls up the remnants of glue, helps to achieve the desired results.

All of the above tips are time-tested and give positive results with careful handling of all devices.

But if you conclude a contract for the production, supply and installation of plastic windows with one organization (which is the best option), then make sure that they take care of removing the film from the window as well.

Today there are several types of film, each of which is designed for reliable protection dwellings from the scorching sun. At correct use such material allows you to reduce the summer temperature in the rooms by five to ten degrees.

Such a protective agent has only one serious drawback - the difficulty of removing it from windows. The composition of each film includes an adhesive substance with which it is fixed on the glass. And in many cases, when removed, it can leave visible marks on the window, which will negatively affect its appearance.

Sun protection film on the window

Everything existing species films are made from materials that reflect light, and many of them contain aluminum, which can also leave ugly stains on glasses. It is quite difficult to remove them without causing any harm to the glass surface. But if you use a number of chemicals designed to clean complex pollution, then you can try to remove traces of the use of a protective film with minimal damage to the glasses.

Everything modern materials, which are designed to protect the premises from excessive high temperature, contain aluminum and other substances that make them difficult to remove from surfaces. In order not to leave ugly streaks and noticeable stains on the glasses, to remove such protective equipment should be approached with the utmost care and responsibility. There are several of the most common ways to be careful, each of which can lead to success.

Steaming

If you peel the sun protection material from the windows without pre-training, then the likelihood of stains and noticeable traces of adhesive is huge.

The ideal way to prepare the film for removal is to use a modern steamer.

The procedure for cleaning windows from material using a steamer is carried out in several stages:

1. A small area is heated with hot steam from a steamer. It is very important that the steam is directed to a specific place on the window.
2. About five minutes after steaming, you should pick up a piece of film and gently pull it towards you, separating it from the window.
3. The new section of the window is reheated until the material begins to move away from the glass.

The section of the film is heated with a steamer
After five minutes, it separates from the window

This is the most gentle and easy way to remove solar control film. In this case, the minimum amount of traces remains on the window, which can be easily removed with a simple soapy solution. This is just one of the simple answers to the question of how to remove the film from the window glass without visible marks.

Detergents and cleaners

Among other effective methods, one can single out the use of powerful ones designed for cleaning glass surfaces. They allow you to remove stains and traces of the film from the window without special efforts, but when using them, safety precautions should be observed, which consists of the following rules:

• when treating surfaces with chemicals, the prescribed protective equipment must be used. These include gloves, closed clothing and a respirator;
• adherence to the dosage indicated by the manufacturer on the container detergent;
• compliance with the manufacturer's recommendations to avoid contact of the substance with some materials that are sensitive to the components of the cleaning agent.

Use protective equipment
Learn Dosage

You can clean windows with effective means, how:

• Domax. This substance is intended for gentle care of glass ceramics and does not contain abrasive substances;
• Cosmofen;
• Shumanite;
• Fenosol.

Shumanit is an effective remedy

However, even modern powerful preparations designed for cleaning surfaces cannot always cope with the consequences of the presence of a protective film material on window glass. In this case, stains and other marks will have to be removed with a harder scraper, which is designed for cleaning glass ceramics. The remaining traces are then removed with a modern Fenosol cleaner. After that, the glass is washed first with soapy water, and then with warm clean water.

All the methods described above, which tell how to remove the sun-protection film from glass, are also suitable for cleaning wooden windows and for modern PVC and metal-plastic profiles. Compliance with safety precautions and the dosage of cleaning agents will allow you to rid your windows of the remnants of the protective material without much harm to the glass and without compromising health.

Scraper for cleaning glass ceramics

other methods

There are other ways by which you can try to remove the film from the window. One is to use a utility knife or other sharp object such as scissors. During the procedure, you need to gently pry the edge of the film with a knife to separate it from the glass, and then pull it towards you. It is recommended to roll the already peeled off sections with a tube so that they do not stick to the window again.

You can also remove some types of film with newspapers and soapy water. The procedure is carried out in several stages:

1. Ordinary newspapers are placed on the entire glass area.
2. Newspapers are sprayed with soapy water until they begin to stick to the surface.
3. Leave for an hour, regularly wetting the paper.
4. Newspapers and film are removed, which will come off much easier after the procedure.

Newspapers are placed on all glass
They are sprayed with soapy water
Leave for an hour constantly wetting
Easily remove newspapers and film

Precautions for removing film stains from glass

When cleaning windows from traces of solar film, the recommended precautions should be observed. Some of the chemical cleaners may negative impact on the skin and respiratory tract of a person, and when using sharp objects, you can get hurt. Therefore, when removing stains from the film, you must adhere to the following rules:

• carry out all work related to chemical cleaning agents only with strong impervious gloves;
• when wiping marks, do not press hard on the glass, as this may violate its integrity;
• when working with sharp objects (knife, scissors, scraper), you should act as carefully as possible so as not to get hurt or damage the window;
• avoid contact of chemicals with unprotected skin, eyes or inhalation;
• keep materials and tools intended for removing traces from glass surfaces out of the reach of children.

The owners of plastic windows are often faced with the question of how to wash the protective film. Of course, it is much easier to remove it immediately after installing the window, but often, the owners do not immediately peel it off or completely forget about it.

However, there comes a time when the protective material will still have to be removed. Then the question arises, how to remove the dried film from plastic windows?

Naturally, it is important not to damage the window during this process, and you also want to do everything as soon as possible and without any extra effort. What can be done in such a case? Effective Ways exist, which means they can be safely used.

But in order to successfully remove the protective film, you must first understand the essence of the problem in more detail. Then it will be much easier to solve it.

Causes of Hard Film Adhesion

Why do you need a film on metal-plastic profiles? Companies through its gluing ensure the integrity of the product during transportation and installation. On the one hand, it is good that such protection is pasted on plastic windows. However, as ordinary people then get rid of it? When the product is already in place and the protective layer is no longer needed.

Very often, windows are changed during a complete renovation of an apartment or house. This means that after the installation of PVC window profiles, a thin film coating remains for some time, until the repair is completed, and dries up.

After a few weeks, the film adheres more strongly to the plastic and practically merges with it. Dealing with dried up protective material is no longer easy.

Why does protective tape stick more strongly over time:

1. Unscrupulous window manufacturers usually save on some nuances. Their range just includes glue, which is used to glue the protective material. There is such an unusual pattern, the lower the quality of the adhesive used, the stronger it attaches the film to the window. In this case, there are only two options, it is either to remove the film layer immediately after installing the metal-plastic product, or to choose the manufacturer more carefully.
2. The time of year, oddly enough, also greatly affects the adhesiveness of the protective tape. In winter and autumn, for example, the frame is cold, the glue seems to curl up and the adhesion of the film to is minimized. If outside the window is a warm season, then the stickiness increases, and it becomes difficult to clean the profile.
3. If you have sunny side, then we can say with confidence that already a week after the installation of the PVC window, the film will stick strongly if it is not immediately removed. The fact is that under the influence of constant heating from sunlight, the protective tape, as it were, dissolves, connects with adhesive mixture and strongly adheres to plastic. And then it dries up. Therefore, draw your own conclusions, and it is better to immediately tear off the tapes from the frames.

These are the main reasons why the film protective layer can be difficult to remove even a month after installation. The whole essence is hidden in the adhesive composition. He must be fought with.

How to remove the protective film from plastic windows correctly? There are several ways. Choose individually the most suitable for you.

Mechanical Elimination Techniques

There are only two such ways. These are the most effective and proven methods.

Let's take a closer look at them:

1. Scraper application. If you have a question, how to remove adhesive tape then a scraper will help. IN winter time of course, it is better not to use this method, since the adhesive remains dense, and it will be difficult to scrape off the protective layer without damaging the plastic. But in the summer, this the best option, the protective coating should be removed well and quickly. The scraper is able to effectively cope with the melted adhesive composition on frames and double-glazed windows. Depending on the length of stay of the tape on the windows, it can be removed in different ways, in small parts or in large segments.
2. Stationery tape. How to tear off PVC film? Very easy with duct tape. The bottom line is that, as already mentioned, the adhesive protective paper is very thin, so it can not be easy to remove it with a continuous tape. Here an ordinary wide adhesive tape will come to the rescue. It is denser, and therefore stronger, than window tape, that's the whole point. All you need to do is simply stick the tape tightly on top of the film, and then tear it off along with it. Thin ribbons can be easily removed and remain on the tape strip.

All other methods are based on chemical exposure. But there is also a heating technique, which is also considered good and uncomplicated. However, it also has its own nuances.

Removal by heating

How to remove film from plastic windows? If you have a building hair dryer at home, then it can be used to quick removal old protective film plastic window. You can also try using a household steam generator. The main point is to melt the adhesive layer between the film and the window surface, so that the tape will come off more freely.

The following points must be taken into account:

• you shouldn’t heat it too much, as the ribbon can melt, then the task will only become more complicated;
• after warming up, be sure to first let the window cool down;
• do not rush, otherwise the tape will be removed unevenly;
• you can not keep the hair dryer too close;
• hot air should not be directed to the plastic profile, but to the glass.

If you follow all the recommendations and perform the procedure correctly, then tearing off the sticky protective paper will not be difficult. It will be enough just to pry off the edge of the tape with a knife or scraper, and then remove the coating in a continuous piece without interruption.

Chemical removal method

You can also remove the film from plastic windows using chemistry. The basis of such methods for removing a protective coating from profiles are chemicals. They are able to dissolve sticky material, which then will be easily peeled off, and then it can simply be washed off.

So, you can use the following cleaning products:

• Shumanite;
• Anti-scotch;
• Mellerud;
• LABEL OFF;
• composition of RP-6;
• composition of WD-40.

All these tools will come to the rescue to peel off old stickers, adhesive tape and wash off adhesive stains from PVC windows, as well as help to clean old paint. They are perfectly capable of scrubbing the protective tapes on the profiles, while not damaging the plastic surface at all.

If after removing the film there are still traces of glue, then they should be completely wiped off so that dust does not stick. You can use white spirit or acetone to remove them. And also try to clean the stains with a clerical eraser.

Removal of the sun protection layer

Another fairly common question, which concerns not only plastic, but also wooden products, this is how to remove the sun protection film from the window? Is it possible to rip it off at all? Yes, of course it's real. However, any kind of strong solvents are inappropriate to remove the film. How to wash the glass in this case? An ordinary knife and a soapy solution will suffice, or you can use Shumanit.

It should be said right away that removing sun protection will not be so easy. But if you spend some time and make an effort, then everything will work out.

How to clean film from glass? It is advisable to slightly warm the surface of the glass with a hair dryer before starting work. Next, carefully wipe the window with soapy water and proceed to remove the coating. The glue will gradually dissolve, and the protective canvas, tearing off, will have to be carefully pry off with a scraper.

Finally, the double-glazed window and frame washes from the sun-protection film store remedy for washing glasses. If scratches were found on the plastic after the work done, then Cosmofen will come to the rescue. However, before using it, you should carefully study the instructions.

Here are some simple ways to clean the film on the windows. The main thing is to do everything slowly and carefully. Then the result will be excellent, and there will definitely be no traces or defects left.

How to remove protective film from plastic windows

According to the manufacturer's recommendation, the protective tape from the plastic window should be removed, preferably within the first 10 days after installation. Subsequently, it will not be possible to easily remove the film, since the properties of the adhesive will begin to change under the influence of heat and sunlight.

To solve the problem, you can invite craftsmen from a cleaning company who will quickly and professionally clean the surface of the window from the adhering film. But with certain skills, you can try to remove it yourself, using a special scraper for glass ceramics and a building hair dryer. You can peel off the tape with industrial alcohol or tape, if you can tear it off in pieces.

The purpose of the protective film on a plastic window is to protect the surface of the unit from possible scratches and dirt. After delivery of the product, installation and implementation of slopes, the film must be removed.

It is best to do this immediately, but this is not always possible. But it is necessary to remove, even a strongly stuck tape. It's worth trying several ways.

Heating the film with a building dryer

This is one of the most simple methods removing unwanted film. If you heat its surface with a hair dryer, soften the layer of old and dried glue, then it will be easy to pick up the edge of the tape and lift it at least a little. Then, direct a stream of hot air under the film, and gradually pull it, gradually tearing it away from the window block. Thus, without breaks, you can remove the whole strip.

When working with a building hair dryer, hot air should not be allowed to hit the glass - it can burst from high temperature.

Mechanical scraping

If the film cannot be lifted due to the fact that it immediately begins to tear and crumble, it is worth using scrapers to clean glass ceramics or to remove paint, you can also work with a universal blade, but in all cases you should take a new blade, then the surface to be cleaned will be more even. It is also necessary to preheat the old tape each time with a building or conventional hair dryer in turbo mode, you can use a steam generator. Residues of glue and film are easily removed with a scraper, which is held at a minimum angle to the surface.

Using tape

Sometimes after cleaning there are stuck pieces that could not be removed. In this case, a wide tape will come in handy. First you need to degrease the surface of the profile with detergents or alcohol. It is better to use the hard side of the sponge and wash everything thoroughly.

Then you need to dry the surface, stick adhesive tape on it and level it with a rag. It needs to be removed after an hour. On its surface there will be stuck pieces of a protective film.

Any attempt to remove stubborn pieces with a blade or abrasive cleaners may result in damage. plastic profile. However, small scratches can be removed with Cosmofen brand white glue, which is also called liquid plastic. Sometimes the German cleaning agent FENOSOL S 10, which has a slight dissolving effect, can help. It is applied to a cotton napkin and wipe the damaged surface. When using these drugs, it is necessary to follow the safety precautions and rules for working with these substances specified by the manufacturer.

Special adhesive removers

When the remaining film needs to be removed, and a hair dryer is not available, then it is worth using means to remove adhesive residues. The universal American aerosol agent WD-40, which has white spirit in its composition, can help in this matter. The substance does not interact with plastic, removes stickers and dirt from glasses.

Other substances have a more targeted application and are used to remove adhesive residue, adhesive residue from stickers. Among them is the HG sticker remover - which completely removes stickers, self-adhesive tapes, oil and bitumen stains. As with everyone chemicals such a principle of action, you need to work with it very carefully, keep it away from children.

Application of HG sticker remover is simple, just bend small corner on a sticky film and drop a little liquid there. Leave for a while, and then you can simply remove everything and wipe this place with a cloth.

Solins, LAVEL OFF, Antiscotch and others have the same ability to remove adhesive residue.

Remaining glue stains on the profile can be removed with a cotton pad and white spirit. You can use a regular school eraser, but it will take a long time. And then you need to completely wash the window with warm soapy water.

Before applying any of these products to the face window profile, it is necessary to check its action in a hidden area between the frames or near the seal. If the color of the frame has changed or turned yellow, the structure of its upper layer has changed, then this tool should not be used.

How to remove protective film with alcohol

When the film crumbles into small pieces, which are almost impossible to tear off the surface, technical or medical alcohol. This requires a small spray gun, the one used to moisten the leaves is also suitable. indoor plants. It is necessary to fill the container with alcohol and spray it on the contaminated frame. After a few minutes, it remains only to wipe the desired place with a hard sponge or brush. Do not use metal brushes or washcloths for these purposes, as they will damage the plastic.

Spray alcohol should be careful, do not allow splashes to get into the eyes. At this point, there should be no children or pets in the room.

If the repair in the apartment has not yet been completed, and the windows have already been installed, then in order to avoid problems with the removal of the protective film in the future, it is better to remove it immediately. And before the installation of slopes, wall plastering, wallpapering and painting begin, it is better to seal the plastic surface with masking tape.

The listed methods for removing the used protective film from PVC windows are the simplest and not too expensive. But if for some reason there are a lot of various contaminants on the windows, you should not risk it. appearance these products, it is better to call the specialists of the cleaning company.

After the plastic windows have been installed, you must immediately remove the protective film. Many do not pay attention to it and believe that it will protect the windows for a while. In fact, if you delay this matter, then there will be problems in removing it, because over time it begins to crack and burst, which does not add beauty to the windows.

When and why should you remove window film?

It is customary to install windows without removing the film. Manufacturers recommend removing the film within 10 days of window installation. You need to know that the protective film consists of 2 layers glued together. The manufacturer's advertisement is usually placed on the first layer, and the second is tightly glued to the surface of the frame. If it is not removed in time, then under the influence of heat and the sun, the glue thickens and sticks firmly to the surface. The front layer can still be removed, but the bottom layer will be removed in pieces.

3 ways to remove old film from plastic windows

If it was no longer possible to remove the film in time, now you have to work hard. There are several proven ways to remove film from windows.

1 way

It will take patience and effort. To remove, you need a blade or thin sharp knife. It is necessary to pry the film with this object and tear off the protruding ends with your hands. And so on until complete removal.

Then the remaining glue is removed from the surface. It is erased with an ordinary eraser. You can also use a sponge and detergent to wipe the frame until it is completely clean.

2 way

This method is suitable if the bottom layer is not "tightly" stuck. To do this, you need a building hair dryer or even one that is used for drying hair, but powerful. They heat the surface of the film and use a thin scraper to remove it. Residues of glue are washed off with detergents.

How to remove an old film from a PVC window using various tools can be clearly seen in the video:

3 way

Here, a steam cleaner is used to remove the film. The film is thoroughly heated with steam, then removed from the frame with a glass scraper. To get rid of the glue on the frame, it is best to use white spirit. It washes off the adhesive well without damaging the plastic surface. If it is not possible to completely remove it, then you can impregnate the film with a cloth dipped in white spirit.

Film remover for plastic windows

Not all products can be used to remove the film as they may damage the surface. Denatured alcohol, that is, industrial alcohol, is considered effective and does not damage the surface of PVC.

To treat the surface Denatured alcohol should be poured into a sprayer and sprayed with a film, do nothing for about 5 minutes. Then its edge needs to be pry thin knife and gently pull on the tape. She must pull out. Spray again and pull off the remaining film. So until the entire film is removed.

If you wish, you can purchase a specialized product - a natural cleaner and stain remover Starwax. It is enough to spray it on the film, wait a few minutes and remove it with a scraper. As a bonus, the product has a pleasant aroma of orange peel.

In order not only to remove the film, but also traces of glue, it is suggested to use any car body cleaner:

How to remove the film from the plastic window sill?

To remove the film from windows and from the windowsill, the same methods are used. The fastest and most effective is the removal of the protective material using special means"Admiral", which is produced specifically for PVC surfaces:

• Wet window sill.
• Hold for 5-7 minutes.
• Take out the glass ceramic scraper and use it to scrape off the film.

Do all this several times until the film is completely removed. If dirty marks remain, then the article "" will tell you how to remove them.

Video: How to remove the protective film from PVC windows?

The video shows how the remnants of the old protective film are removed in a very simple and original way:

So, in order not to bother yourself with the work of removing old film, you need to immediately remove it after installing the windows. Then there will be no difficulties - it can be easily removed, you just need to pull a little. It should be understood that such a film is intended to protect materials only during transportation.