How to stick a film on windows from the sun. Heat protection - glue the sun protection film on the window What to glue the film on the windows

Window tint films, in addition to their direct purpose, protection from bright sunlight, perform a number of additional functions.

They have decorative properties, protect privacy from prying eyes, and in case of damage to the glass, they do not allow the fragments to crumble. To give the glass surface such universal properties, you need to choose a quality material and figure out how to properly glue the tint film on the windows.

Composition and types of films

The material for the manufacture is polyester, which is an environmentally friendly polymer. The films are a durable multilayer composite with elastic properties. They allow you to minimize the amount of incoming solar energy without loss of optical visibility. From above, the material is covered with a metallized layer of nickel, bronze, titanium or aluminum, which performs the protective function of the internal structure.

Depending on the number of layers, the deposited metal, the presence of dyes, the films are divided into:

• sunscreen,
• mirror,
• shockproof,
• decorative,
• architectural.

Film gluing steps

To understand how to stick a sun-protection film on a window, here is a brief instruction. To do this, you need glass cleaner, cotton rags, a wide rubber spatula, a stationery knife, liquid soap, and a spray bottle. Before sticking the tint film on the glass, it is necessary to thoroughly wash the window on both sides and carry out a wet cleaning of the room to prevent dust from entering.

The material is cut with a margin of about 2-3 mm. A mild solution of liquid soap is sprayed onto the surface of the window to facilitate the movement of the film. Then the gluing process takes place. The material, aligning the edges, is applied to the glass and with a wet spatula squeeze out water from the center to the periphery, avoiding the formation of wrinkles.

As the film dries, the film will lighten and the bubbles will disappear. This process takes about a week. If necessary, the protruding edges are cut with a knife. It is important to consider temperature and humidity. Optimal conditions for work: 5 - 40 ° C and 20 - 80% humidity.

Tinted films do not require special care: they are wiped with a microfiber cloth with soapy water. In the fall, the material is removed.

How to glue a mirror film on glass: on your own or with the help of professionals, everyone decides individually. The appearance of the window, the degree to which the material fulfills its functions, and comfort in the house will depend on the quality of the work. Therefore, if in doubt, it is better to consult a specialist.

Let's start in order. Sun protection film for windows is different. It differs in the density of tinting, the color of the coating, the method of installation and removal from windows. Physically, window film consists of an ordinary transparent film, on which a thin layer of metal is deposited. Moreover, the instructions clearly indicate that it is necessary to glue the film on glass with this "metal" layer. If you stick it the other way around, then, firstly, the effect of reflecting sunlight will not be achieved, the effect of the film in this case is much lower, and secondly, you can’t tear it off the glass later.

If you turn to professionals for help, they will come to your home or office and paste the film on the windows themselves. Moreover, they use a reliable proven film and know how to glue it so that there are no bubbles left and the window does not lose its transparent properties. A well-pasted film is even invisible on the glass and its presence can be detected only by opening the window and making sure that it turns out to be much lighter than it seems on the street.

But the services of professionals are expensive, and a good film costs a pretty penny. So, for example, if I have seven windows in my apartment, then sticking the film with the help of professionals turns into a very tangible waste. When I took the prices and got the price of the service, expressed in five figures, I felt a little uncomfortable. The desire to save money and manage on our own grew stronger with each sunny day. Looking ahead, I can say that it was easier to immediately install with silver coating and argon inside and forget about the problem for many years.

Well, to be completely honest, I don’t really trust professionals, because among them quite often there are random people who will do the job on the principle of a blunder, and if you start to resent, they will send you away. By nature, I am not a brawler, but I'm already a little tired of "wiping up puddles" for the so-called professionals.

Therefore, when the next spring came, and the sun powerfully reminded of itself, I went to the store to buy window film. This is now such a film is sold in almost every hardware store. And then it was a terrible deficit. Therefore, I was very pleased when I managed to find and purchase several rolls of the coveted product.

Here's what film I managed to buy.

I hope by now this manufacturer has gone bankrupt and ceased to exist. At least his site is no longer open. Such a "kind" attitude towards a representative of the domestic industry was born after using his miracle products.

The fact is that the metal layer on the film was applied extremely unevenly. There were places with a very thick layer, while in others it was practically absent.

Let's digress from the fact that I did not stick the film on the glass quite accurately. It was the first experience. There were bubbles that, no matter how hard I tried, I could not expel. I know that a real professional would be horrified and would pass an appropriate verdict on my mental incompetence :). The problem shown in this picture is the uneven density of the metal layer. In fact, three pieces are pasted here at once. Pay attention to the left wide piece. On the left side, it is quite normal, but the closer to the right edge (in the middle of the window), the more transparent the film becomes.

The most striking thing was that this unevenness was already revealed after sticking the film on the window. I glued it with ordinary water. Only not from the tap - there we have a lot of bleach and other nasty things - but pure spring.

I did not want to go for another batch of film, which could turn out to be just as successful. All summer the film remained pasted on the glass. In principle, in part, it really saved from harsh sunlight in the summer.

But the main "ambush" was waiting for me in the fall, when it was time to shoot the film.

In those areas where the metal layer was normal, everything went without complications. But the areas devoid of a metal layer turned out to be firmly stuck to the glass. Even in the summer in the heat, I noticed that the film is very hot from the sun. Apparently the layer adjacent to the glass softened a little and "grabbed" tightly.

In order to scrape off the protective film, I had to use tools. Naturally, the surface of the glass was scratched. Further, banal claws were used :). The job went faster and without scratches on the surface. The film was removed in small pieces and was completely transparent:

On one window on the balcony, I did not begin to remove the film from the glass. You just don't have the patience.

I called the manufacturer at the number indicated on the package. The director himself answered. I started telling him about the problems with his products, but he wasn't particularly impressed. Having swallowed another piece of a sandwich (he constantly ate something during the conversation), he suggested that I go to court and hung up.

Of course, I didn't go to court. A roll of film cost about 60 rubles, and the fact that I spent a lot of time and ruined the windows removing it, so it still had to be proved. Apparently, the manufacturer knew that no one would sue him because of these pennies, so you can safely send everyone to court, and drive the marriage yourself with complete impunity.

It happened in 2010. Since then, I do not support the Russian manufacturer, but buy imported German film from EMTEC. Attaches and removes with one touch. No bubbles and "undeveloped" areas% experience - a thing to come. No problem, even though it's four times more expensive.

There is a Russian film with similar quality:

Sometimes I buy it.

But now I'm already a scientist: before I start to blur the film on the windows, I first roll out the roll and look at it through the light. Fortunately, more such "successful" rolls have not yet come across.

And one more thing: it is better not to glue the film on the glass, but to fasten it to the frame with adhesive tape. It is more convenient, there are no bubbles left and then, after removal, you do not have to wash the windows from streaks.

So that, buying tint film for windows, be careful. Beware of fakes and intrigues of domestic manufacturers. If you are completely unbearable from the heat, spend a little more and order a sticker from a trusted company. Or consider installing sprayed double-glazed windows. They have a lot of interesting features that you don't even know about. At the same time, save on heating.

Getting into our house through the windows, often cause a lot of inconvenience. Ultraviolet radiation negatively affects well-being and mood. Protect yourself and your loved ones from this will help the sun-protection film on the windows.

The main purpose of the films

The rays of the sun penetrating into living quarters can spoil any interior, because walls, curtains, and furniture are subjected to fading. In addition, excess ultraviolet radiation adversely affects domestic plants, animals and the human body. Modern reflective films successfully solve these problems. They effectively reflect the energy of the sun, preventing the glass from heating up, as well as objects inside the apartment.

Film properties

The modern market offers a variety of films that can prevent the penetration of sunlight into apartments and offices. Sun protection properties are achieved by repeated application of layers of aluminum and titanium metals. It is these metals that provide the reflection of ultraviolet rays and the absorption of heat, while the transparency of the glass remains the same. Sun protection film on windows will help not only protect the interior of the apartment - it will also provide a comfortable stay for pets and active plant growth.

Films on windows are able to reflect and absorb up to 90% of solar radiation, as well as up to 70% of heat, providing a cool climate and protection from solar radiation. Films are produced in various shades and have different degrees of toning. Depending on the level and amount of penetrating light, you can choose a film with varying degrees of tinting, which will allow you to control the penetration of rays and provide comfort.

Sunscreen film on windows: types

Today, there are many types of films with different characteristics and applications. There are products, the installation of which is quite simple and can be carried out independently, without the involvement of specialists. The only condition is clean glass. As a rule, such films are applied to the inner surface of the window. The thickness of the protective material ranges from 110 microns and above, depending on the manufacturer.

Reflective solar film on windows has completely different parameters. Reviews of people who have used just this option confirm that in addition to protection from ultraviolet radiation, it is resistant to mechanical stress. The minimum thickness of such a film is 300 microns.

Depending on the efficiency, films are of two types:

• medium-efficient - transmit up to 40% of the light and filter up to 70% of the sun's rays;
• highly effective - reflect the entire ultraviolet flux, passing more than 50% of the light.

All reflective films comply with environmental standards, they do not burn, do not emit toxic substances.

Preparatory work

Sunscreen film on windows is not so difficult to glue, but the procedure still requires certain skills and knowledge. Therefore, it is necessary to strictly observe all the rules and recommendations, if it becomes necessary to independently perform this work. First you need to make accurate measurements of the glasses that need protection. After that, the required amount is calculated and the material is cut, adding 0.5 cm of stock to each side. You should know that rolls are produced in standard width - 1.52 meters. Marking and cutting for convenience is carried out on any hard surface using a felt-tip pen, ruler and scissors, while it is necessary to align each corner.

Installing solar control film on windows: features

Reflectors can be installed on the glass on the inner surface, the outer surface, as well as inside the double-glazed window (as a rule, this happens at a window manufacturing company). The maximum effect is achieved if the film is glued to the outer surface. The sun's rays are reflected without heating the double-glazed window. If the film is installed on the inner surface of the window, the efficiency can be significantly reduced. After all, the double-glazed window is heated, and the effect of the heater is created.

How to install solar control film on windows

Do-it-yourself installation is usually carried out only on the inner surface of the window. To do this, it is necessary to prepare in advance a mixture of purified water with shampoo (5 drops of shampoo per liter of water), window cleaner, spray bottle, spatula and knife. First you need to wash the glass until it is completely free of dirt, dust and possible grease stains. After that, the mixture is applied with a spray gun on the adhesive side of the film and on the glass. This is necessary in order to be able to move it on the glass until it takes the optimal position. After that, you need to get rid of air bubbles. To do this, moving from the center to the edges, smooth the film with a spatula.

Well, how to stick a sun-protection film on a window, we told. By the way, there is an important point that must be taken into account. If an energy-saving coating is applied to the inner glass, sticking the film may cause the glass to break. Thus, in this case, only the external use of the reflector is possible.

Benefits of Using Solar Reflectors

The use of solar films has a number of advantages that can be appreciated literally in the first days after installation. In the summer months, it will be possible to significantly save on electrical energy, since the air conditioner will turn on much less frequently. In winter, heat loss will decrease, which will also save the family budget. In addition, reflectors protect the dwelling from the penetration of sunlight, as a result, the interior of the apartment, furniture and objects will retain their original color, and the quality of life of the inhabitants will become much more comfortable. It should be noted separately that the material we are considering is an additional sound insulation, and in the event of an accidental entry of a foreign object into the window, the glass will not crumble into pieces.

Film removal

There are many sources of information regarding how to stick sun protection film on a window, but sooner or later this film has to be removed, and then certain problems can arise. Dismantling is a process that requires certain skills and free time.

There are several ways to clean glass.

1. Mechanical. The film is cut into strips with a sharp knife, the edges are lifted and successively removed. However, this can damage the glass, plus everything, the method in question takes a lot of time if the amount of work is large.
2. Chemical way. Ammonia is applied to a cloth, which is attached to the surface of the glass and left for several hours. After that, the film can be easily removed without leaving marks. It remains only to thoroughly wash the surface.
3. With the help of equipment. A building hair dryer of sufficient power copes with this task perfectly. Under the flow of hot air, the film begins to rise. It is better to move from the edges to the center. After removing the reflector, a small amount of glue remains on the glass, which can be easily removed with a special solution. This method allows you to remove the obsolete sun protection coating much faster without damaging the glass surface.

do-it-yourself installation of sunscreen, tint and decorative films

If any contamination remains, repeat the procedure.

2. Moisten the glass with a sprayer with an installation solution: for 1.5 liters of water - 1 cap of baby shampoo (for example, Johnson and Johnson, you can use Fairy).

3. Remove the transparent protective layer from the prepared piece of film, to do this, glue the tape on both sides and pull sharply in different directions, a dark sticky film will remain on one tape and a transparent one on the other.

Wet the film. The film must be completely wetted.
The water (installation solution) temporarily neutralizes the adhesive, allowing the film to move across the glass surface.

Apply to glass top corners of the film and fix (smooth) them.

Spread the film over the glass surface, avoiding the formation of wrinkles and creases.

4. Again wet the surface installed film. Water will provide easy sliding of the water separator (scraper or rubber spatula) and will not allow scratches to form if solid specks get under the forcing.

Start Smoothing film and distillation (squeezing out) of the installation solution from under it.

Start work from the central upper part of the canvas. Move the forcing (scraper or rubber spatula) from the center to the edges, from top to bottom.

First with light movements, then gradually increasing pressure. Under the surface of the installed film, there should be no air bubbles and water "lenses".

5. Trim excess film extending beyond the edge of the glass, forming a gap of 1-2mm (optional). This gap is necessary for the exit of the installation solution.

Squeeze out the water with short forcing strokes perpendicular to the edge of the film.

Tip: to more effectively remove water protruding from under the edge of the film, wrap the distillation with a paper towel - the escaping water will be absorbed into it.

It is forbidden to wash the film within 5 days after its installation in order to prevent moisture from getting under the film and causing water lenses.

better to see once

Watch the video: how to install a film on windows with your own hands without bubbles and wrinkles in three minutes

Many people search this article for queries: window film wrapping, how to glue on a window, installing a sun-protection film on windows, how to stick sun-protection film on a window video, how to stick it on a window, how to stick a film on a window from the sun, sticker film on windows, paste over window film, how to stick the film on the window from the inside,

how to glue the film on the windows of the house, glue the windows with a film, how to stick the film on the glass of the window correctly, the technology of stickers on the windows, the solar-reflective film on the windows by writing.

The process of sticking film on windows is not complicated, but requires experience and adherence to the procedure for sticking film on windows. You can actually stick the film yourself. To do this, we publish instructions for self-sticking (installation) of film on windows. This instruction allows you to stick all types of window film.

Instructions for self-installation (sticker) of film on windows

1. We glue (install) the film only from the inside of the room. It must not be exposed to rain and snow.
2. Make accurate measurements of the glass to be pasted and draw up a cutting chart (i.e. plan how you will cut the film).
3. Use scissors or a utility knife to cut pieces of film based on the cutting chart. The size of a piece of film should be 2 cm in width and length larger than the glass on which this piece is glued. You will cut off these excesses at the very end of the film sticker.
4. Prepare an alkaline solution with which you will wash the glass before installation. Recipe for a solution to prepare a window for tinting: 50 ml of detergent (for example, fairy or baby shampoo) in 1.5 liters of water.
5. Moisten the glass with an alkaline solution and pass a rubber spatula over the surface of the glass. Drive away water and dirt. Move the scraper over the glass surface from left to right and from top to bottom.
6. Re-wet the glass and use a "rubber with metal edge" scraper, such as those sold for cleaning car windows, to sweep any water down the glass.
7. Wet the glass heavily with an alkaline solution and spray water in front of the glass so that all the dust around the glass cannot settle on the wet glass.
8. Remove the protective layer from the prepared piece of tinted film. Tip: stick tape on the corner on both sides and pull the tape in different directions.
9. As soon as the protective layer is removed, spray the adhesive layer with an alkaline solution. This will neutralize the adhesive and allow the film to move across the glass as it is applied.
10. Attach the top corners of the film to the glass. Fix them and smooth them. Lower the bottom corners of the film and allow the film to adhere to the glass.
11. Spread the film over the glass avoiding creases and creases. And starting from the center with a rubber spatula, drive water from under the film. The movements should be short, no more than 20 cm. Each movement, start from the place where the film has stuck and move to the edge of the film.
12. Cut off the excess film around the edges with a utility knife.
13. If dust particles, hairs are visible under the film, then remove them as quickly as possible. To do this, lift the edge closest to the mote, remove the mote and moisten the film. If the mote is hardly noticeable, then we advise you not to remove it, since the film becomes electrified from smoothing and begins to attract motes from the air. And there is a chance by removing one mote to get several new ones.
14. This completes the installation of the film on the windows. It is forbidden to wash the film within 5 days after its installation. In the future, wash windows with detergents that do not contain abrasive particles (for example, window cleaner can be washed, but not with scouring powder).

ANSWERS ON QUESTIONS

Do you do car tinting?

No. We do not tint cars.

Is it possible to install a protective film on the glass outside the room?

It doesn't make sense. The reinforcing coating must always be located on the side opposite to the possible impact. In addition, the film should not be exposed to atmospheric influences. The ideal place for the film is in the inter-glass space (inside the double-glazed window).

Is there a film through which I will see, but not me?

In principle, films with one-sided transparency do not exist, but the use of mirror metallized films makes it possible to achieve a similar effect. Moreover, this becomes possible if you are on the less illuminated side. That is, if you are indoors and there is a bright sun outside, the glass surface will look like a mirror from the street. If you turn on the light in the room at night, silhouettes will be visible from the street.

What problems can arise when self-sticking a film on glass?

• If you poorly prepare the window for pasting, then the film will stick with defects (there will be specks and bubbles under the film).
• If you make mistakes in cutting, then you may not have enough film for all the windows or you will have to glue strips of film on the windows, which will greatly spoil the appearance.

Is it possible to book and tint glass at the same time?

Can. There are explosion-proof and at the same time tinting films. Thickness 125 microns and 54% reflection of solar energy - Solarblock Safety IR-cut 5050 .

Do the glasses with the film installed on them require special care?

Special care for the tint film is not required. The film has an anti-scratch layer, so it can be washed with any cleaner that does not contain abrasives.

Can a protective film replace grilles?

Yes, if the purpose of installing gratings is to prevent unauthorized entry into the room. A blow with a hard object on glass with an impact-resistant film punches a hole in it approximately the same size as the impact tool. It will take a considerable amount of time to widen the gap necessary for access to the interior of the room. This means that security personnel have the opportunity to respond to an alarm and prevent a crime. In addition, any object thrown at armored glass, be it a rock, a grenade, or a Molotov cocktail, bounces off and stays outside. If it becomes necessary to leave the room through a window (for example, in case of fire), then such glass is easily squeezed out from the inside.