What kind of glue to glue shells to glass. How to glue decorative elements

Vacations. Take the most common wooden photo frame and use glue to attach shells to it. Try to place them close to each other so that there are no empty spaces.

Using shells, you can create a postcard or even a panel. Take the base - thick paper, cardboard, canvas. Think over the composition in advance. Your panel can be abstract or, on the contrary, with a complete plot. It is best if you draw a sketch, which will indicate the approximate location of all the elements. paper base can be dyed in any color. For panels, use not only shells, but also any other material - fabric, beads, beads, decorative stones, dried flowers and grass. In art stores you can find a huge amount different materials that will inspire you to be creative. They can be fixed with glue "Moment". Some elements (lighter than shells) can be glued with ordinary PVA. Be sure to put your panel in a frame.

Shells can be used to decorate a vase, flower pot or pencils. First, cover the surface of the bottle (or vase) with plasticine, and then press various things there, in this case shells. You can go further - in a building or art store, such as "Rotgypsum". Such a base will create the effect of a natural shell rock. Using a spatula, apply the mixture to the product (vase or bottle) that you want to decorate, and until everything is dry, press the shells there.

Another idea for an original crafts: Make your own shape (for example, a pencil holder) from clay (sold in stationery stores or in the departments for artists). Until the product is dry, press the shells. Sculpting from clay is not difficult at all - the process reminds everyone of the familiar work with plasticine.

note

Now available in many shops special sets for creativity with marine elements. But perhaps for your product you want to use hand-assembled shells. In this case, they must be processed in order to avoid an unpleasant odor that may occur after a while. To do this, it is enough to boil and dry the shells.

Helpful advice

You may want to paint the shells a different color before making a craft out of them. For this, it is best to use acrylic paints.

Related article

Sources:

• crafts with sea ​​shells

Collecting by the sea is a favorite pastime for children. They beg their parents to take the treasure home. Then these "trophies" lie somewhere in a distant closet. They interfere with cleaning, but it's a pity to throw them away. Seashells can decorate a photo frame or make a picture out of them, which will not only decorate your home, but also remind you of a happy vacation.

You will need

• - shells;
• - plywood, flat board or chipboard;
• - PVA glue;
• - stain;
• - jigsaw;
• - sandpaper.

Instruction

Make a sketch. If you're not very good with a pencil, find a suitable postcard or digital image. Scan the postcard, open it in the program Adobe Photoshop and make a contour image. Try to choose a drawing with a small amount of small details. The material with which you have to work is very beautiful in itself. In addition, it has a certain texture, and this must be taken into account when making a sketch. Resize the image and print.

Prepare the base. It is best to take a fairly thick plywood or board. Perfectly suited, for example, wooden cutting board. If it has a hole for a nail and you don't need it, glue a wooden cork into it and cover this area with a painting element. regular board process sandpaper to make the surface even. Consider whether you leave the shells light or color them. The choice of stain depends on this. In the first case, it is better to make the background darker, then the light shells will look more contrasting. If there is no stain at hand, you can use a dark solution of potassium permanganate. It gives shades from light brown to deep red-brown.

Draw a picture on the board. This can be done, for example, using carbon paper. You can not do a sketch at all, but try to draw it right away on the board from shells, like a mosaic. If you choose to color the shells, do so before you start gluing them on. Use bright acrylic paints. The color depends on the nature of the image. Of course white swan it is better to make it from white material, which is very similar to feathers. Flowers can be white or multi-colored, and for a landscape panel, you will most likely need elements different colors. The seascape is a very appropriate subject. Shells painted in greenish and bluish color perfectly transmit waves.

It is best to stick such material with PVA glue. But you can use any other - universal or hot glue. Nobody forbids you to add your picture other materials. Suitable beads and beads, exotic plants or even the most common cereal, from which you can make flower stamens and spots on the petals.

Helpful advice

You can make a picture without glue. For her, you need a plain plasticine. Cover the base with it. The layer should be from 2 to 5 mm. Level the surface. Apply a drawing. Arrange the shells in the desired order and lightly press each with your finger. Such a picture can be redone depending on the mood. Such a "set" can be excellent board game for your child.

Sources:

• shell paintings in 2018

Tip 3: Easy DIY Seashell Decor Ideas

The memory of the sea can cheer you up in any critical situation. After resting on the seashore, stocks of materials for creativity are always replenished with shells, pebbles and other marine paraphernalia. It's time to get them and put them into practice simple ideas for decor from sea shells with your own hands.

Instruction

The box is a great item for decorating with seashells. Artificially age the surface of the box using the colors of the sea. Add seashell decor and a nautical-inspired box will hold your jewelry and remind you of a great time.

By decorative elements, I mean rhinestones, pebbles, mosaics, shells and other nice little things that can complement the decor.

Let's say you've created a beautiful seascape on canvas. Of course, for volume and realism, I want to add a large beautiful shell and a couple of cobblestones (sorry, pebbles found on the occasion). Moreover, a dried starfish just asks for a canvas. Only here on PVA you cannot glue these decorations. What glue to take?

Surely you have seen that designers usually use a “hot gun” in television workshops. You can buy it at a hardware store.

Glue for the gun is available in the form of rods. You load the gun with them and plug them into the socket. The glue starts to melt. Now pull the trigger and squeeze the liquid adhesive mass right into the right place on the canvas. And press the shell there. The glue dries quickly and the shell is glued! Everything is great. What are the downsides?

Minus 1. The glue is very hot and viscous. Be careful yourself and do not give this tool to small children!

Minus 2. Difficult to squeeze out a small amount of glue, so it sticks out from under small objects. Well, nothing, it's transparent.

Minus 3. The collage turned out beautiful. You hung it on the wall and can't stop looking. Only in the evening suddenly the pebbles fell off one after another with a roar ... By morning, a shell followed them. The star, due to its dryness, lasted longer than the others. And all due to the fact that not every hot melt adhesive is able to hold a heavy object. complex shape on difficult surfaces.

But the glue gun is indispensable when gluing light decorative elements with a “floristic bias”, such as dried flowers, ribbons and other absorbent and loose material.

There are other options, such as Moment glue and various super-glues. You can use them, but the pungent smell and the same malleability are a little embarrassing.

You can also try various adhesives for mosaic. However, they are not all perfect. Some have a smell, others have a color. Ideally, we need a transparent adhesive that is easy to use, odorless and provides reliable adhesion to the surface.

Perhaps the most convenient glue for gluing decorative elements is glue for rhinestones. It is suitable for any surface, including fabric; has no smell, tk. made on water based; easy to use - they cannot be burned and easily squeezed out, because it is packaged in a soft tube with a thin spout. And, most importantly, this glue holds really firmly. You can usually buy it in art stores, in the same place as all decorative materials.

Another great glue is clear acrylic gel. It comes in matte or glossy. If you are working with a matte surface, it is better to take a matte gel (and vice versa). Acrylic gel meets all our requirements. The gel is available in plastic tubes or glass jars. I usually use gel for gluing large elements and it has never let me down! However, keep in mind that both glue and gel dry for a long time. If you paste big item, and besides, uneven (such as a shell), a lot of gel will be needed. The surface must be horizontal. Apply glue or gel, put a shell on it. If necessary, excess gel can be easily removed with a cotton swab. Leave the product to dry until the gel is completely dry (preferably for a day). If the elements are small, a small drop of glue or gel is enough. The glue will "grab" very quickly, the gel - a little longer.

I advise you to try these tools, you will surely like them. Just remember to dry and degrease the surface well before gluing. And one more note: if the shell fell off along with the paint, then it's not the glue. The reason is the poor adhesion of the paint to the surface. That is why it is necessary to prepare the surface for painting.

I wish you creative success!

Instruction

There are several types of rhinestones. The most common are rhinestones cold fixation, hot-melt adhesive and sew-on. Sew-on rhinestones, based on , are sewn onto the fabric and have special holes for . Hot melt rhinestones also designed for fabric. They initially have adhesive base, with the help of which, for example, with an iron, they are glued. Adhesive rhinestones cold fix are glued with glue and are ideal for glass surfaces.

Choose a background material that will successfully complement the composition - it can be a dense fabric of any shade, which should also match the color of the frame you have chosen, in which the picture will be framed. You can paint the frame yourself, or choose a ready-made one.

Lay out parts of the future composition on the base and fabric. Distribute the petals from around the centers, lay out the leaves and stems, determine where they will be located decorative elements- leaves, dried flowers and so on. Determine the location of the main and secondary figures in the composition.

Remove unnecessary items - do not overload the panel with an excessive number of elements. When you achieve the most harmonious look of your panel, start gluing its elements to the base in sequence.

Heat the glue and glue the middle of the flower - you will start from it, building the big picture. On each individual shell petal, drip one or two drops of hot glue and glue the shell to the base near the middle.

Then, trying not to move the previous petal, glue the next one - and so on until the shell petals form a full circle around the middle. Then glue the stem and leaves of the flower, and finally, the secondary decorative elements of the picture.

When the glue dries, take a critical look at the panel and consider whether it is worth adding or changing it in some way. Cut off the elements that go beyond the picture and decorate it. Coat shells and dried flowers with varnish for durability.

To give the fabric a glamorous sheen, as a rule, hot-melt adhesives are used. rhinestones(thermo rhinestones) or ready-made rhinestone appliqués (Hot Fix) + heat-resistant transfer film. This is a kind of rhinestones, on the bottom of which is already applied adhesive composition. Glue melts when exposed to high temperatures and fastens rhinestones on the the cloth.

Instruction

For fixation the cloth in the form of a scattering or an author's composition, you need a special soldering iron. This device is capable of gluing one crystal at a time, heating it only to the required temperature.

To put on the cloth ready-made application (Hot Fix), first you need to remove protective film.

Glue the application on the cloth using a transparent adhesive film on which the ornament is attached.

flip the cloth with applique so that the ornament is on the bottom.

Lay a double layer of ironing fabric on top of the product. thin materials.

Close the heat press. If necessary, you can replace it with a regular iron. Iron thoroughly required space iron (no steam!), heated to about 170 degrees. The pressure of the heated surface must be directed directly onto the application!

After the time required for rhinestones stuck to the fabric, lift the cover of the heat press or remove the iron. As a rule, the terms are indicated on the packaging of the application.

After the appliqué has finally "stick" to the fabric, peel off the transparent adhesive film. This should be done with a film that has already cooled down so that no fragments of it remain on the fabric.

note

To select the most suitable conditions for applying rhinestones to fabric, it is highly recommended to make a few drafts on scraps of your fabric.

Helpful advice

To receive best result applications should be applied to the elements of the pattern, and not finished models clothes.

Take into account zippers, buttons and other protruding parts.

Thin fabrics such as organza do not absorb glue very well.

Do not apply applications on smooth leather and smooth artificial leather, dense polyamide, as well as fabrics treated with silicone or wax.

Always allow the transparency film to cool completely before removing it.

If film fragments still remain on the fabric, steam off this area or re-apply the thermal pressure technique.

Sources:

• Technologies for attaching crystals to fabric: 3 main methods
• What you need to know. How to glue rhinestones?

connect two glass surfaces can be done in several ways, and it depends not only on the choice of glue, but also on the state, requirements for appearance seam and the conditions in which the elements to be glued will be located. The strength of the seam can be ensured by polymerizing glue, which hardens under the action of ultraviolet rays. However, it is not always appropriate.

The choice of glass adhesive

Curing adhesive, which cures under UV light and is designed to bond glass, provides a strong connection, often transparent, which is important. Its main drawback can only be called the fact that at least one of the parts must be transparent to ultraviolet light, otherwise the glue will not harden and form a strong uniform contact.

Painted parts or colored glass elements are best fixed with cyanoacrylate-based adhesives. You can also use a two-component adhesive with epoxy resin. The first option sets very quickly, already within 20 seconds. The smaller the adhesive layer to connect the parts, the better. Epoxy glue dries within one day and can create a significant layer without loss of strength.

Glue with cyanoacrylate is afraid high humidity. From contact with water, it begins to crumble over time, lose its properties and strength. Epoxy resin, on the other hand, is resistant to water.

In addition to the listed products, you can use silicone-based hot melt adhesive or compounds like liquid nails. However, such a connection for strength requires a large layer between the surfaces to be glued, this option is more suitable in cases where it is necessary to fix some decorative elements on the glass that are not subjected to significant load.

How to glue glass

For any glue, the preparation phase is the same. Gluing processes may differ slightly, but not significantly. To begin with, the surfaces to be glued should be thoroughly cleaned of dirt and, possibly, of the remnants of old glue. Next, you need to degrease them. For this, Galosha gasoline is used, alcohol in the case heavy pollution or soap solution or detergents for windows with acetic acid with minor contamination.

When using an adhesive with cyanoacrylate, it is desirable to clean the surfaces and, if necessary, level them for a tighter fit. In case of use epoxy resin, in the place of gluing, it is desirable to make the surface rough. For example, you can walk on it with sandpaper.

After that, a layer of glue is applied to the cleaned surface according to the instructions and the parts are pressed tightly so that they stick thoroughly. It is important that the surfaces to be bonded do not move until the adhesive has fully cured.

Exposure to ultraviolet radiation from lamps can adversely affect vision, you should use safety glasses or directional emitters.

To harden the polymerizable adhesive, it is necessary to influence the bonding site with ultraviolet light. Experience shows that most often it is enough to expose the part to the sun. Otherwise, an ultraviolet lamp with a wavelength of 300 to 450 nm is used.

Related videos

Today, almost no home interior can do without a mirror. It is necessary in the bathroom, hall, wardrobe and much more where. Installation finished product, which has a frame and special fasteners, does not cause any particular difficulties. But sometimes, when decorating a room, you need to stick a mirror on a vertical surface - for example, on a wall or a cabinet door. This task is not easy, but it is quite feasible.

Before purchasing a mirror, decide on the desired size of this product. Measure the dimensions of the future mirror to the nearest millimeter, leaving a margin of 4-5 mm around the entire perimeter.

Most importantly, remember that the edges of the mirror should not come into contact with other trim elements, otherwise it may crack. The mirror is difficult to cut on your own, so it is better to entrust this work to the masters. Then it will have the correct geometric shape.

When you pick up a mirror from the workshop, pay special attention to its edges. They must be carefully crafted and rounded. This is necessary so that the gluing process is safe and you do not cut yourself.

Depending on what exactly you need to glue the product, apply different methods its fastening.

How to glue a mirror on the wall

First, prepare the wall for gluing the mirror. Smooth out all irregularities, treat with a deep impregnation primer to ensure better adhesion to the adhesive. The latter must be designed specifically for the mirror.

Then proceed directly to the process of gluing the product. You will need pieces of 10-15 cm double-sided thick tape. They need to be glued after approximately 60-70 cm on back side mirrors. Scotch tape is needed to hold the mirror until the glue dries completely. When the adhesive tape is pasted, remove from it protective part and using a gun, apply glue over the entire back surface and the edges of the mirror, approximately 15-20 cm between the strips.

Immediately after that, put the mirror against the wall. The lower part of it must necessarily rest on something until the glue dries. Also make sure that there is a gap around the entire perimeter of the product. Press the entire surface of the mirror carefully and gently against the wall. The adhesive setting will occur within 20-30 minutes, and its complete drying - not earlier than in 1 day.

How to glue a mirror on a cabinet door

The mirror can also be glued on the cabinet door, thereby updating the interior of the room. Since in this case the product will be used small size, double-sided tape is used, specially designed for mirrors.

First stick it around the perimeter on back wall mirrors, and then at regular intervals of about 40 cm, add vertical stripes adhesive tape. Then carefully glue the product on the cabinet door. It is recommended to mark in advance with a pencil on the cabinet the borders of the future mirror.

How to glue a mirror on ceramic tiles

The mirror is glued to ceramic tiles. In this case, a special glue is also used. Apply it in a continuous layer around the perimeter of the product. The indent from the edge should be at least 2 cm. Be sure to coat the middle of the mirror with glue in a lattice form.

The procedure for gluing on ceramic tiles is similar to the above described method of fixing a mirror to a wall. However, in this case, after the glue has dried, it is necessary to cover the edges of the product with white or transparent sealant.

If the mirror is quite large, covering the entire wall, it is better to fix it mechanically for safety reasons. Carefully drill it with a special glass pen or a diamond-coated tubular drill. Drill the wall in these places with a puncher. After that, fix the product with a decorative glossy bolt.

Please note that in order to work with large mirrors Definitely need 2 people. In addition, you will need means to protect your hands from cuts - for example, cloth gloves.

Related videos

Keeping shells as a reminder of carefree days on the beach is best in the form of interior items, jewelry and souvenirs. After all, they are so beautiful, completely free, natural and durable material. In this article you will find 50 inspiring photos, 8 ideas and as many step-by-step DIY shell crafts for beginners.

Basic instructions for preparing shells

cleansing

Before you start making crafts from shells, you need to properly prepare them.

• If the shells are “dead” and there are no remains of mollusks left in them, then they just need to be soaked in a solution of water and any chlorine-containing agent (for example, with bleach, “Duckling”, etc.) in a 1: 1 ratio for 30 minutes. If the shells are very dirty, or you want to remove the dark outer layer (periostracum), then soak them longer. After soaking, brush the shells with a brush and rinse in clean water.
• If the shells are "live", that is, they have the remains of mollusks (albeit long dead) and have bad smell they must be thoroughly cleaned. To do this, dip the shells in boiling water for 5 minutes, and then remove the remains of the mollusks with tongs, nail scissors, etc. There is a second way: heat the shells in the microwave for 30 seconds, then try to remove the remains with tongs. If unsuccessful, continue heating the shells in the microwave, checking the result every 10 seconds. Once all the remains have been removed, treat the sinks with chlorine according to the first instruction.

After processing, inspect the shells for chips and, if any, sand them with a sanding block, disc, or sandpaper. If desired, you can give them a shine with clear nail polish or furniture, as well as with oil or fat cream. True, in this case, before processing the shells with glue, the gluing points will have to be additionally degreased with alcohol.

Hole drilling

To make some types of shell crafts (for example, wind chimes, garlands, beads, bracelets and other decorations), you need to drill a hole in them. This task is quite simple, the only difficulty is that the shells can crack or delaminate at the drilling site.

Therefore, remember the main rule: the thinner the shell, the smaller the hole should be in it and, accordingly, the thread / accessories of the decoration.

To make such beads, you need to drill holes in the shells and string them on a silk cord, fixing the location with knots. Further, the ends of the laces will only need to be clamped in the crimp ends and attach the fasteners to them

To make such beads, you need to drill holes in the shells and string them on a silk cord, fixing the location with knots. Further, it remains only to clamp the ends of the laces in the crimp ends and attach the fasteners to them.

There are two ways to make holes in shells - manual and automated.

Method 1. Pick up a drill for a drill, screwdriver or straight grinder with a diameter of 0.8 - 2 mm. Place the shell on a wooden or plastic board and stick it on with masking tape. Drill a hole straight through the tape - it will not allow the shell to split or delaminate.

Method 2. If you do not have a screwdriver or drill, then you can make a hole in the sink with a carnation and a hammer. To do this, first glue the shell with masking tape, put it on inside shell mark, then attach a nail and gently tap it with a hammer a few times to make the initial hole. Next, expand the hole by moving the same nail back and forth inside it until you reach the desired diameter.

If there was neither a nail nor a hammer at hand, then use an ordinary needle, nail scissors or a knife and "drill" the hole by hand. The result will appear in about 10 minutes.

Idea 1. We encrust frames, frames and frames

Shells can be used to decorate the frame of a mirror, picture or photo frame. We present examples of such crafts in the following selection (scroll the photo to the right).

Today we offer you to decorate a frame for a mirror with shells, but by the same principle you can decorate any photo frame or picture frame.

Materials:

• Small, medium and large shells and, if desired, additional decorations (eg, starfish, pearls, skate figures, etc.).
• Glue gun and a few sticks of glue or clear epoxy.
• Newspaper or any waste paper to protect the mirror from glue.
• Masking or regular tape.

Instruction:

Step 1. Protect the mirror with paper by securing it with masking tape. At this stage, the frame can be painted if it is original view does not suit you.

Step 2. Sort the shells by size to make it easier to create a future composition.

Step 3. First, glue the first row of small or medium shells (about the same size) around the mirror.

Step 4. Now start gluing the largest shells. Beforehand, you can play with the layout options and choose the best one. If you are using epoxy, then after all the parts are glued, leave the frame to dry overnight.

Idea 2. We make a Valentine panel

From the shell collection different forms and sizes, you can make a panel in the form of a valentine. However, you can cut out any other shape from cardboard / plywood, say, the same seahorse or a letter.

Materials:

• Glue gun or any strong adhesive;
• Collection of river and sea shells;
• Cardboard;
• Scissors;
• Leg-split.

Instruction:

Step 1. Cut out the base for the heart-shaped panel from cardboard.

Step 2. Use a knife or awl to make two holes for the twine.

Step 3. Start gluing the shells, trying to leave minimal gaps between them. Leave the loop holes open.

Step 4. Cut the twine to the desired length, thread the two ends of the rope through the holes from the inside of the panel and tie into double knots.

In the next video, you can see a visual master class on making crafts from shells with your own hands in the form of a valentine panel.

Below are other ideas for creating a panel of shells.

Idea 3. "Write" a picture on canvas

And here is another idea for creating a wall craft from shells.

Materials:

• Canvas on a stretcher;
• Shells;
• Glue gun or other strong adhesive, for example, "Moment";
• Template or stencil of the desired design, printed on paper;
• Acrylic paint for background (optional)
• Brush (optional)

Instruction:

1. If you want to repeat the idea of ​​​​the painting of this master class, then first create a background for the composition of shells. To do this, use a brush and acrylic paint desired color. Wait for the background to dry before moving on to the next step.
2. Fix the template or stencil to the canvas with masking tape, and then trace its outlines with a pencil.
3. Start gluing the shells on the drawing without going beyond its borders.

Also see our other articles:

Idea 4. We cook candles for mini-candlesticks

Shells are almost finished miniature candlesticks that are just waiting to be supplemented with paraffin wax and a wick. You can use the resulting candles for table setting, a romantic picnic or just for decorating the interior.

Materials:

1. Sea or large river shells;
2. Small round candles in tin molds;
3. Water and a saucepan for a water bath;
4. PVA glue or double sided tape.

Instruction:

Step 1. Remove the candle itself from the tin container, and then remove the wick from it by pulling the metal base at the bottom of the candle (see photo). Set aside the wicks and return the candles to their molds.

Step 2. Glue each wick on double-sided tape or PVA glue in the center of the shell.

Step 3. Now we need to melt the paraffin to completely liquid state. You can do this in three ways:

1. Bring the water in a saucepan to a boil, then lower the heat so that the water stops boiling, and lower the molds into it.
2. Put the candles on the stove, heated to the minimum heat, and make sure that the paraffin does not burn.
3. Warm up the wax with a hair dryer.

Step 4. As soon as the paraffin is melted, remove the molds from the heat and proceed to filling the shells. It is best to use any tongs or a pair of Chinese sticks for this. Remember to protect the table surface with newspaper beforehand.

• If the shells are already too unstable, and you are afraid that the paraffin will harden unevenly, then it is better to spread the candles into the cells of the egg packaging or fix, for example, with soft plasticine that does not leave marks.

After about 20 minutes, the paraffin will completely harden, and you can enjoy the light of candles from shells.

Idea 5. Making a marine-style topiary

Topiary is a small ornament in the form of a tree in a pot. You can learn the principles of making topiary from shells with your own hands in our master class or from the following video lesson.

And in this selection of photos you can get ideas for decorating a topiary from shells with your own hands in a traditional way. round shape or in the shape of a Christmas tree.

Idea 6. We make a flower candlestick

If you have enough bivalve shells, you can make beautiful flower-shaped candle holders out of them.

Today we propose to make just such a craft from mussel shells.

Materials:

• Shells of bivalves;
• Any round base of small diameter;
• Glue gun;
• PVA glue (optional)
• Glitter (optional).

Instruction:

Step 1. Prepare the shells - wash them with soap, remove the remains of organic matter and, if desired, bleach them with chlorine-containing products (see instructions at the beginning of the article).

Step 2: Paint the round base of the candlestick in a neutral color such as white.

Step 3. While the base dries, sort your sink set by size.

Step 4. Start gluing 1 row of shells on the sides of the base with hot glue.

Step 5. When the first row dries a little, start creating the second row, placing each new shell overlapping the previous one and so that it is between the two shells of the first row. As a result, you will have a layout of two rows of shells in a checkerboard pattern, as shown in the photo.

Step 6. Glue the third and all subsequent rows according to the same principle, but not on the base, but on the joints of the shells of the previous row (the place is marked with an arrow in the photo below).

Step 7 When you have glued the last row, inspect the candlestick and add one or two more rows where you think it is needed.

Step 8. Hooray, the shell candle holder is ready! If desired, you can additionally decorate it with sparkles. For this you need to do the following:

• Treat the shells with PVA glue inside or only around the edges.
• Sprinkle glitter generously on the craft, let the glue dry, and then shake off the excess.

Idea 7. Create wind music

Shells are perfect material for the manufacture of wind music, because the "chime" of such sea bells is very pleasant to the ear.

Materials:

• Twine, fishing line or any thread.
• Twig or wooden stick.
• Scissors.
• Hot glue gun or tool for drilling small holes (drill with a 2 mm drill or just a needle and nail scissors).
• Shells.