Ceiling plinth for liquid nails. We begin to glue the ceiling plinth: how professionals work

The ceiling plinth (it is also called a fillet) perfectly hides all the irregularities at the junction of the ceiling and the wall. Not a single room is an ideal polyhedron - this is unattainable in the construction of buildings. Consequently, the wallpaper on top will lie unevenly. Such a defect must be masked, and best of all - with the help of fillets. Today I will share my experience and tell you how to properly glue the skirting board to the ceiling.

There are many different options on sale, but you only need to pay attention to the fact that the entire skirting board (all strips) are from the same batch. for its gluing in building materials stores is also always available. So there doesn't seem to be any problem. Read the instructions for the rules for using glue and start working.

However, the main difficulty in gluing the skirting board is in the correct fit of its pieces to each other. When we glue along the wall, there will be no particular difficulties. But how to be at the corners, how to join the pieces of the plinth in these places? That is why you will have to take at least one more strip in the store for training, and stock up on a construction or stationery knife for cutting paper. They are very comfortable and evenly cut fillet. You can still cut with a hacksaw, but a knife is much more convenient. You need to cut exactly exactly so that later the joints are invisible.

Nuances when gluing the plinth

The plinth is better in the following sequence: first stick the pieces of strips in the corners, and only then glue along the perimeter. If the strips are glued evenly in the corners, then there will be no difficulties on straight sections of the wall. Ready-made corners of ceiling plinths are sold in stores, but if you could not buy them, you will have to cut them yourself. It all depends on the correctness of the selected cut angle. It is necessary to practice on separate pieces in choosing an angle (for this, they buy an extra strip). It is necessary not to confuse only where the right lane will be, and where the left lane will be. Better mark with a pencil. If it’s not possible to cut the bevels correctly by eye, then you need to use a device called a miter box, which you can either buy or make yourself.

Plinth pieces are glued to the ceiling and wall in turn. It is necessary to pay attention to the correct choice of the place for gluing the first piece in the corner, because the neighboring one is glued to it. As we glue, the corner will look. Glue is smeared with a thin strip on that side of the plinth, which will be adjacent to the wall and ceiling. If the ceiling is stretched, then the glue is only on the back of the lower part of the strip, which will be pressed against the wall. After applying the glue to the fillet, you should wait a little, and then press the strip tightly to the place of gluing. The glue will set quickly.

Masking joints and gaps

If it is still visible at the junction of the strips, then it is well masked by white sealant. Excess glue should be removed immediately with a dry cloth. And one more thing: before starting work on gluing skirting boards, you need to pay attention to the cleanliness of your hands. On the plinth, after it is pressed with hands during gluing, dirty spots may remain.

If you have not painted or whitewashed the ceiling yet, then the next one will be the best finish. With a light putty, go over all the glued baseboards, smearing them like paint, and after drying, remove the excess with a fine sandpaper or a special sanding sponge for work on. After this final finishing, the skirting board and the ceiling will become one, and you will not be able to find a single gap - the work will look perfect. Here is a little secret from personal experience. You can find out more secrets by watching the video:

In addition, skirting boards outline the contours of the room well, making it visually more spacious, and complete the entire interior.
You can glue the ceiling plinth with your own hands. Below we will describe in detail how to quickly glue the ceiling plinth.

There are several common materials from which ceiling plinths are made. Before buying, determine what exactly you want to buy and what material suits you best. Below we will consider the types of materials for ceiling plinths.

The foam skirting board has two advantages: light weight and affordable price. For budget and high-quality repairs, this option is ideal. In addition, the foam plinth is very easy to process.

The disadvantage of this material is high flammability and fragility. The fragility of this part makes it difficult to work. And in the bathroom, such a plinth cannot be installed, since the foam does not tolerate a humid environment.

This skirting board goes well with drywall surfaces. In this case, it is installed on a plaster putty.

It is possible to glue foam ceiling plinths on the wallpaper, but it is better to glue them before the repair work begins.

This is necessary in order to change the wallpaper after a certain time without removing the cornice. And the ceiling can be simultaneously with the ceiling plinth.

The use and installation of a cornice is no different from a foam plinth

Cutting the corners of the ceiling plinth

Correctly glue the ceiling plinthis the key to success. You need to start from the corner, and it is better to cut all the details in advance. easy to process, so you can use a regular mounting knife.

To do this, you need to take a plinth and draw a line with a pencil
at an angle of 45 degrees. Then cut with a knife along this line.

The same actions must be performed with another plinth so that the resulting corners fit exactly. You can practice on old scraps if you are not confident in your abilities.

After the final fitting, sign each part so that they are not confused during the gluing process. The gap in the joints of the corner plinths should not exceed 1.5 mm.

If the gap between the baseboards turned out to be much larger, then do not despair. Sealant will help solve this problem. Also, a narrow strip of the ceiling plinth can be pushed into a large gap, and then fixed with glue.

How to glue a ceiling plinth?

For high-quality adhesion with putty, the surface of all walls is primed.

For a good fit, all edges of the foam ceiling plinth must be sanded. The seams are covered with either acrylic sealant.

After the entire structure has dried, all seams are treated with sandpaper and painted. Any water-based paint is suitable for painting.

If the wall is uneven, you will need additional fixation of the skirting boards in the form of masking tape. It is easy to remove after completion of work, leaving no marks even on the surface of paper wallpaper. You can glue the ceiling plinth on the wallpaper on liquid nails.

After completing work with skirting boards, you can proceed to the subsequent finishing of the room. If you are going to paint the ceiling, then the baseboards will have to be painted with the same paint.

All edges after cutting are processed. Sealing and fitting joints does not differ from the technology described above.
Acrylic sealant is used in work with almost all polymer building materials.

Polyurethane skirting board

Due to the flexibility of the plinth, it can be run along an oval column.

In addition, the color of the skirting board can be changed by staining.

The scope of this type of skirting boards is much wider than others.

It is ideal for decorating any structural details and elements.

A plinth made of this material is used for stretch ceilings and in rooms with a complex configuration.

These skirting boards are used in cases where the room is sheathed with a board, or. Wooden ceiling plinths are used as a decorative element.

The skirting boards themselves are mounted on special wooden mechanisms, and small decorative elements are glued to the glue.

For a more correct arrangement of all parts, the plinth is marked. The line of the ceiling plinth should pass below the bars. Hole locations are marked below.

Ceiling plinth (baguette, fillet) - a finishing element that visually smoothes the transition from walls to ceiling with its shape, color and texture. Everyone who repairs the premises on their own should know how to glue the ceiling plinth. Only with careful fastening of the plinth, it will have a beautiful visually pleasing design and a finished look.

The purpose of the plinth

The obligatory placement of a ceiling plinth has always raised questions. On the one hand, it is an element of decor, it does not carry a practical load, on the other hand, it performs the following functions:

• when an innocent marriage is detected in the corners of the room or the boundaries of the ceiling and walls, the fillet hides flaws;
• if you need to align the angle between the planes, then the plinth is the best solution;
• choosing the right color and size allows you to visually enlarge the space or give the room an original look;
• installation errors of the stretch ceiling system are also covered with a fillet or a baguette;
• when organizing the ceiling lighting of the room, the plinth hides the technical elements.

To install a skirting board or not is the individual choice of each owner of the premises. But if it is made in favor of this decorative element, then you should study what types exist, what to attach to and how to glue the skirting boards on the ceiling yourself.

Skirting board types

Skirting smooths the transition from walls to ceiling, so it is important to choose a material that harmoniously fits into the design in terms of shape and texture. The following options are available for sale:

1. Wooden. It has a natural beauty, its own texture. Matches with many styles. Restrictions are associated with the use of high humidity indoors (bath, open attic). Basic carpentry skills are required for proper installation.
2. Gypsum. The presence of ready-made options and the ability to independently produce any texture, using purchased forms, makes the material universal. In the early times, it was the main material for modeling around chandeliers and corner structures.
3. Polyurethane (cost 300 rubles / unit) - a flexible, wear-resistant product. It is used in the design of complex structures, such as the outer contours of columns, internal rounding curves of turns of stretch and multi-level ceilings.
4. PVC (plastic) - 40.0 rubles / unit. For ease of installation of products from this material, manufacturers offer connecting strips, versatile corners. Used to complement plastic finishes. Mounting the product will not create difficulties even for a beginner in home repairs.
5. Styrofoam products (cost 20 rubles / unit). Versatile, can be used for mounting on wallpaper, plastered walls, wood and plastic structures. It has a low coefficient of flexibility, but sufficient to eliminate irregularities.

On the presented photos you can get acquainted with all types of ceiling plinths and options for their use.

Advice! Before starting work, it is necessary to determine how to glue foam ceiling plinths, which compositions are suitable for other fillet options. The complexity of the work and the final result depend on this.

Features of adhesives

Before gluing the skirting boards, it is necessary to determine which of the adhesives to choose for installation:

• polymer - securely fastens wood, foam and polymer baguettes, easy to use, does not require special knowledge when gluing;
• liquid nails, produced on the basis of two bases of different chemical composition - acrylic and neopropylene, are recommended for fastening fillets made of wood, polymer, in structures where bends are required, complex profiling (stretch ceilings, multi-level structures);
• adhesive putty, where the composition is prepared independently by mixing PVA glue, putties and water, the scope is convenient to stick gypsum cornices, eliminate mounting cracks.

Advice! For gluing light elements, you can use gypsum mixtures - the drying time is minimal, but you also need to work very quickly for this reason.

Skirting board installation

Before gluing the ceiling plinth, it is necessary to carry out a number of preliminary organizational measures, including:

1. Defining the shape, texture, color of the plinth.
2. Calculation and acquisition of necessary materials.
3. Tool preparation and selection of accessories.

Preparatory activities

Based on information about the use of skirting boards made from different raw materials, the owner of the premises determines which one to choose. At the same time, the main role is given to the style of the design of the room, no less important is what elements of decor it is complemented with. A winning option if the texture or ornament of the ceiling plinth reflects the connection with other objects in the room. Conventional solutions are represented by a combination of plain walls with ornamental baguettes and vice versa.

After deciding which and how baguettes will be glued, the required amount of material is determined. When calculating, it is taken into account that the standard length of one factory product is 2 linear meters. When creating the contour of the walls, docking will require cutting at an angle, but no one is immune from mistakes during work. Thus, one or two measured sizes of the plinth are added to the total length of the perimeter of the room.

Prepare in advance:

• roulette or ruler construction;
• thin marker or pencil;
• miter box (devices for trimming the corners of the joints);
• hacksaw for metal (you can use another cutting tool, but it is not guaranteed that it will be convenient to cut);
• spatulas made of polypropylene or metal;
• container for the preparation of the adhesive composition;
• household sponges;
• rag.

Forming the plinth: corners and joints

Before gluing the plinth to the ceiling, it is necessary to calculate the junction and the cutting angle. To do this, start working from the far corner from the entrance to the premises, filling with molding those areas where you can use the whole product, and then supplement the areas by trimming the excess.

It should be remembered that the external and internal angles when cutting a profile are different. The outer blunt, where the upper part of the workpiece is longer than the bottom, equals 1350, the inner one is an acute angle, the cut edge will be represented by an angle of 450.

A miter box helps to achieve maximum coincidence of surfaces when joining corners. It can be plastic, wood or metal. Visually represented by a product in the form of a channel with lateral oncoming grooves on both sides at the right angles. There are more complex designs of the miter box, where using the rotary part, you can set any trimming angles for external workpieces. But for the installation of a ceiling plinth in a room with right angles, the first, simple option is sufficient. Adjustment is carried out in the following sequence:

• the plinth is tried on directly at the installation site;
• if the distance to the next turn of the molding is less than the standard length, then the excess is cut off with a margin of 3-4 cm (it is better to make a margin than to subsequently join in pieces);
• the workpiece is placed in the miter box and, holding, dissolve in the grooves at an angle of 90 degrees;
• the operation is repeated for the "counter" profile.

Advice! For direct joining of the foam plinth, as a rule, cutting at an angle is not used. Combine evenly cut parts with a snug fit to each other. But when fitting wooden or polymer fillets, it is better to observe an angle for the joint of 450.

DIY glue

If it is not possible to purchase special glue for a foam or polymer baseboard, then it is prepared independently. Would need:

• finishing putty;
• water-based glue (PVA);
• water;
• container and accessories for mixing ingredients.

The preparation of the adhesive composition is carried out in the following sequence:

1. The finishing putty mixture and PVA are placed in a clean dish, in a ratio of 4/1, respectively.
2. During mixing, water is added. Readiness is determined by a creamy consistency.
3. Until ready, such an adhesive should be infused for at least 10-15 minutes.

Important! Use self-prepared glue should be within two hours. When lumps or clots form, they must be removed - kneading and applying will worsen the final result.

Skirting sticker

What to glue the ceiling plinth of foam or other materials on, and how to cut the elements is clear. Direct installation will not cause difficulties if you first apply the exact position of the profile to the wall plane with a simple pencil. Its technology is represented as follows:

1. The field of trimming measured segments at the required angle, an adhesive composition is applied to them with a spatula. Moreover, when using putty with a continuous layer, glue - with two strips on the sides. To achieve the required consistency, 2-3 minutes are given to run the composition.
2. On a dry, dust-free surface, the plinth must be attached to the wall and ceiling, ensuring the formation of the correct seam. A few seconds of hand pressure will allow the adhesive to ensure a good grip of the elements.
3. Immediately after gluing the elements, remove excess adhesive with a rag or sponge. Do not be overzealous - the glue is not completely dry, and the structure may move.
4. Straight segments are joined and glued in a similar way, but it is important to pay attention to the fact that, despite the errors in the walls and ceiling, they are visually even. If a textured border is used, then it is necessary to ensure that the patterns match.
5. If, as a result of checking the work done, surface roughness is revealed, they should be eliminated with fine-grained sandpaper.
6. After the adhesive has completely dried, the seams can be puttied, the baseboard can be painted. The use of construction tape will help to avoid unwanted paint on the walls.

Advice! Minor irregularities on the plane, they can be eliminated by applying an additional portion of putty to the surface during installation. But it is better to eliminate them at the initial stages of repair work.

A video tutorial on how to properly glue a ceiling plinth is presented by the following link:

Conclusion

Using tips on how to properly glue a ceiling plinth during self-repair will help you avoid common mistakes. It will allow you to work quickly and efficiently, as a result - to create a cozy interior, with elements that harmoniously complement each other, without involving a third-party master, whose services per linear meter will cost at least 350 rubles.

Gallery of finished works

Do you want to cut and paste the skirting board on the ceiling correctly, but don't know how to do it? At first glance, this does not seem difficult, but if we consider everything in more detail, then everything is not so simple. The photo below shows how to properly cut and glue the inner and outer corner of the ceiling plinths (fillets) made of foam or polyurethane. All instructions are written step by step in an understandable form with examples.

Ceiling plinths are usually made when it is necessary to close the gaps between the ceilings and the finishing materials on the wall. For example, you have decided, and the farther along the wall, the larger and wider the gap between the ceiling and the wallpaper becomes. I know one person with whom such a situation happened, he did not listen to experienced people and the end result was what he least wanted. And he had to run to the nearest store and buy fillets.

How to glue the ceiling plinth

So let's get started. First, measure the footage of the perimeter of the room and determine how many fillets you need. The length usually goes according to the standard 2 meters. But it is best to buy with a margin, just in case. Also decide on the width that suits you. They can be glued to the wall in different ways.

Before installing the ceiling plinth, it is necessary to prepare the ceiling or wall - their evenness is checked. If there are defects, then level and putty, with a mandatory surface primer. If there are small irregularities, for such a case, fillets with soft edges can be used, which will not create very noticeable drops.

The first way: on a special putty or acrylic (before wallpapering). And the second: immediately on the wallpaper and on the sealant.

Most prefer to mount directly on the wallpaper. We advise as an option to glue on silicone sealant, it is perfect for this job. The manufacturer does not play much importance here. Everything will hold up great. But this method is even suitable for those who have curved walls, since gaps can form between the wall and the fillets, they will need to be covered with the same sealant. It is white, so it will turn out more or less normal.

It is desirable to align the walls. Masters advises to glue the ceiling skirting boards on the putty, that is, before pasting the wallpaper. Thus, the cracks are sealed with putty. And accordingly adjust the wallpaper to the fillets themselves. This option is for the more experienced.

In general, craftsmen prefer to glue the foam baseboard on acrylic white sealant, it can be easily applied, it holds well and dries quickly. Its main property is that they can close cracks, corners and it colors well. The cost of acrylic sealant is within 100 rubles. and it makes little sense to buy an expensive one.

In general, everyone decides for himself which method to use.

How to make a montage

You need to start from the corner of the room. And this is where the problems can start. At first glance, it seems that making the corner of the ceiling plinth is simple, believe me, it is not. You can buy ready-made corners in the store, they are sold together with fillets. If you can't find it, you'll have to cut the corners yourself.

You need to cut using the following tools: miter box, hacksaw, sharp knife. Insert a piece of material into the miter box at an angle of 45 degrees and press firmly. Now it remains at the right angle and cut the ceiling plinth from the right side.

Take your time to glue the cornices along straight sections. First take care of the corners - in this case, you can trim them if necessary, or sand them until a good joint is obtained.

Now we will understand in more detail how the installation of the ceiling plinth is done with photo examples.

How to cut the corner of the ceiling fillet internal and external with a photo

Thus, we cut the plinth, if you need to get an external corner.

As a result, these are the edges of the fillet.

Then the inside corner. Pay your attention, but at what angle and from which side of the miter box you need to cut the ceiling plinth.

Tip: When cutting any of these materials, you should use a fine-toothed hacksaw. Otherwise, an uneven end of the part may result. The large tooth of the tool will bite the material.

This is what happened in the end, after cutting and gluing to the wall ...

The site advises to start practicing on pieces, if everything works out, then go ahead, cut out the inner and outer corners.

If you did everything right, then cut the first corner turned out. You can glue two corner skirting boards to the wall. If you have chosen the method of gluing on the wallpaper, then coat the fillets with glue and attach them more tightly to the wall. Residual adhesive can be removed with a soft cloth. Also cover the gaps between the wall with glue.

If you have chosen a way to fix the ceiling plinth before wallpapering, then they need to be fixed with putty. Apply putty to the fillet with a spatula. And attach it tightly to the wall. Remove residue with a spatula or a damp cloth. Cracks can also be covered with putty.

Tips for facilitating the installation of ceiling dumbbells:

• To measure correctly, the bar is measured between two corners. At the same time, for internal corners, the length is measured from internal elements, and the distance from external corners is measured from a point that is at a distance from the internal one equal to the width of the plinth deep into the room.
• When installing foam skirting boards at the junction between the wall and the stretch ceiling, the glue is applied to the part of the skirting board that is in contact with the wall, and not with the canvas.
• The final fixation of the skirting board is carried out after adjusting the angle of the adjacent plank to it.
• If the wall, ceiling and floor have a right angle, it is easier to adjust the planks below by laying out the parts on the floor or on a prepared table.
• Small gaps remaining in the corners are puttied.
• Particular attention should be paid to the installation of ceiling plinths made of rare wood. In this case, puttying the gaps will most likely not give the expected result. A bright spot will appear on the background of the texture.

Well, are the inner and outer corners ready? So you are doing the installation of the fillet correctly. Now take the next bar and attach it to the wall to the glued plinth in the same way and do not forget to coat the corner joint. When you get to the next corner, carefully measure the distance that is left, and cut off the missing part, everything should be very accurate. The side that goes butt to butt with the plinth will remain unchanged. So cut out each corner. When everything is glued, they can be painted under. Good luck gentlemen and remember that you need to cut after determining the exact size.

Seam masking and painting

If, after gluing the ceiling plinth, there are small gaps between the planks, this is absolutely not a problem, because they can be easily eliminated by rubbing in white sealant. If you have not yet whitewashed and painted the ceiling, then the next one will be the best option.

With a light putty, you need to walk along all the glued planks, smearing them with a coloring composition, and after drying, remove the excess with a fine sandpaper or a special sanding sponge for plastering work. After such a final finish, the ceiling and moldings will become one, and you, in turn, will not find a single gap.

After you have glued the ceiling plinth and eliminated all the flaws, you can start painting the plinth. The process of painting the baseboard is considered optional, but if you want to give your ceiling a finished and more attractive look, then you still need to paint the baseboard.

way, guess

A simple "collective farm" option is to cut "by eye" at 45 °. For this, a joined part is taken, which is adjusted to the previous angle in fact.

You can try on the design on weight, this is a rather long and painstaking business. Need maximum precision!

When fitting, constantly try on the resulting pairing in place. Only after a few fittings can you achieve a good result, and then glue the baseboard on the base. In short, you can't do without experience :)

Video tips to help you glue the ceiling plinth

To make the finish more attractive, expressive and hide any flaws, skirting boards are used on the ceiling. Fillet, molding, baguette or plinth is made from a variety of materials. One of the most popular is foam. Styrofoam ceiling plinth has many advantages, including light weight, low cost and ease of installation. If you have chosen just such a variant of the plinth, then you may be interested in the question - how to glue the foam ceiling plinth.

That is what we will learn from this article. It will consider acceptable means for gluing foam skirting boards, preparing glue for do-it-yourself work, and the process of gluing products on walls. And thanks to the training videos, it will be much easier to do this.

Adhesive options

Let's find out what to glue foam ceiling plinths on. There are three main types of materials that have their own advantages and disadvantages. To find out which glue to glue is better, you need to compare them. The following is a list of these funds:

• polymer adhesive compositions;
• liquid Nails;
• acrylic putty.

Polymer based adhesive

This is the most common version of the fixing composition for foam skirting boards. Glue "Moment" or "Titan" is especially often used. The peculiarity of the compositions is that they have a unique astringent base. What's more, they set quickly and can hold the foam molding firmly.

Note! Alternative adhesives can be found on sale, however, we do not list them, since their characteristics are worse than those listed above.

There is one caveat that is associated with the use of certain compounds. It is important to ask a consultant or read the instructions if the foam adhesive is suitable. The composition should not contain an aggressive solvent, otherwise it will only spoil the surface of the expanded polystyrene.

Liquid Nails

Unlike polymer glue, this option is suitable for any material and will not harm the foam. With it, you can not be afraid to glue ceiling plinths. Liquid nails can hold molding for decades. There are two types of liquid nails:

1. Neopropylene.
2. Acrylic.

What is the difference? The first option is made from an organic solvent. Neopropylene liquid nails have a pungent odor and are hazardous to health in a liquid state if the rules are not followed. The advantage of the material is that it is ideal for rooms with a high level of humidity.

As for acrylic liquid nails, they are the most environmentally friendly and do not affect the integrity of the ceiling skirting boards. Glue successfully copes with its task, only it is a little afraid of wet rooms. Therefore, it is recommended not to use acrylic liquid nails for the bath or kitchen.

Acrylic putty

Some believe that this type of adhesive is the best for gluing skirting boards. And indeed, the putty is good. Even professionals love to use it. There are several reasons for this. Let's start with the fact that the gluing of the product occurs instantly, so there is no need to keep it in one place for a long time.

In addition, thanks to putty, you can hide the gaps between the wall and the foam molding. Putty will perfectly hold the material on the wall. The good news is that it is absolutely harmless and will not affect your health in any way. Even for a closed room, you can use it.

Do-it-yourself adhesive preparation

Before gluing the skirting board, consider a technology that will help you create glue for do-it-yourself foam skirting boards. With it, the fixation will definitely be done perfectly. Here is a list of what will be required:

Now consider the phased preparation of the composition:

1. Finishing putty is poured into the container.
2. PVA glue is also added there. In this case, they are guided by the following proportion - 1: 4. It turns out that 1 part of glue will require 4 parts of putty.
3. The contents are mixed, and water is poured into it. The solution is prepared until the consistency resembles sour cream.
4. It remains to insist the glue for 10 minutes, then mix again.

The glue is ready, you can stick the foam baseboard. In this case, the composition should be used up in 2 hours. Then it will lose its properties.

Advice! It is important that clots and lumps do not form in the composition. If there are any, remove them.

Tools and materials for work

To properly glue skirting boards, you need to have not only glue. Here is a list of what you need to get started:

• paint brush;
• water tank;
• plastic molding;
• hacksaw for metal;
• scissors or stationery knife;
• ladder;
• tape measure, marker, level;
• miter box for cutting at an angle of 45 degrees.

How to glue foam board

In fact, sticking products is not so difficult. Even an inexperienced user can do it. The main thing is that the glued products hold well and are evenly fixed. Foam moldings are easy to bend, cut and stain. This simplifies installation.

The installation of a foam ceiling plinth consists of the following steps:

1. Walls and ceilings are primed and puttied.
2. Level markings are made on the wall. It is important to accurately draw a line that will serve as a guide.
3. The next step is to prepare the plastic baseboard. To begin with, the length of the walls is measured, after which the planks are cut according to the dimensions. From the desired ends, a cut is made at an angle of 45 degrees.
4. At the end, the corners are checked.

All this is a preparatory stage before gluing the plinth. However, the rest of the work depends on the correctness of its implementation.

Advice! When buying skirting boards, it's best to keep one in reserve, especially if you're working with it for the first time. Thanks to this, you can replace the first molding, which may turn out to be lumpy.

When everything is ready, it remains only to fix the foam strip. On the reverse side, the selected adhesive is applied to it, after which the plinth is pressed according to the markings along the perimeter of the wall. With this, everything is simple. I would like to pay special attention to the creation of the corner. Since the wall has an angle of 90 degrees, when installing the plinth, which is simply cut off evenly, you get an overlay. In order for two elements to form an angle at the junction of 90 degrees, they must be cut at an angle of 45 degrees. In this case, the end of one plank has a cut in one direction, and the other plank has a cut in the other direction, as shown in this photo.

How to make it so that this even cut is formed? Everything is simple - with the help of a miter box. This is a special tool that allows you to cut parts at different angles. It is enough to lay the skirting board and cut off the corner according to the template.

You will learn more about how to glue foam skirting boards from this video.

Rookie Mistakes

It happens that when working, the plinth simply does not stick or it fell off after a few days. Newbies often make a few mistakes. In order not to step on the same rake, we suggest that you familiarize yourself with some points that require special attention:

These tips will help beginners avoid common mistakes.

Conclusion

Foam ceiling plinth is a wonderful decorative element with a lot of positive qualities. Moreover, all the work related to fixing it can be done by hand, without involving craftsmen. This significantly affects the cost. After the plinth is glued, it can be painted in any color with water-based paint. Other paints with solvents in the composition will not work. Now you have everything to start the process yourself. If you try, then in a few hours the work will be done. Good luck in your endeavors!