Electric skirting convectors. Skirting convector

Grids for convectors

ELECTRIC HEATERS

WATER IR PANELS

ARTICLES

Megador, skirting convector

Heaters Megador - plinth electric heating convectors. They are designed for installation indoors in the plinth area (the place where the wall and floor meet) and are powered by 220V electricity. The height of Megador plinth heaters is 6 cm, the width is 4 cm. They can be fixed to the wall with brackets (1 cm long) or placed on the floor on legs, also 1 cm high.

The thermal effect of electric convectors Megador (Megador) is aimed at warming up the wall near which it is installed, and then this wall begins to give off heat to the room. This type of device can be attributed to electric warm skirting boards. The floor temperature is about 40°C and Maximum temperature walls 60°C, with a gradient of decrease in height, and already at a height of 1.5 meters - about 28°C.

Megador heaters are manufactured using innovative patented technology. The heating source is an incandescent coil (TEH), located in a metal finned tube filled with quartz sand. This design is enclosed by a galvanized steel casing with powder coating(standard white or brown color). In the case, from the end, a control unit with a power regulator is built-in. plinth electric convector does not “burn” the oxygen of the room, because the coil does not come into contact with air.

Skirting electric heaters can be used both separately and combined into a system. These baseboard heating devices can be controlled using wired thermostats both in manual and automatic modes.

You can buy various series of skirting electric heaters Megador:

• Standard (MR) - a series with smooth power control. The length of the convectors is 1000, 1500 or 2000 mm. Since the beginning of 2017, this series has received an update called Standard. Version 3.10;
• Light (MF) - a series of heaters with operating modes at 50% and 100% power, without a smooth power controller. Convector length - 1000, 1500, 2000 mm;
• Conner - a ready-made corner convector measuring 850 x 850 mm, continuously adjustable from 100 to 400 W, designed for heating corners;
• Group (MG) - a specially designed series for combining heaters in a circuit with parallel connection, i.e. to create a heating system;
• Aroma MWA - a series with the function of aromatherapy, in the body of the device there is a special glass flask for essential oils. Covectors with a smooth power regulator. Length - 1000, 1500 or 2000 mm;
• Greenhouse heater MT-150 - waterproof from water splashes at any angle (IP66) 1500 mm long;

The maximum power consumption for devices with a length of 1000 and 1500 mm is 400 W, for a model with a length of 2000 m - 600 W.

Depending on which side the electric cord comes to the heater, the model can be left (L) or right (R).

The body color of these electric baseboard heating convectors is available in white (W) or brown (B).

Examples of the use of skirting electric convectors for heating various areas in rooms.

Megador Standard (MR)

Convectors with smooth power control from 0 to 600 W.

Since January 2017, the manufacturer has released a new modification of this series, namely Standard Version 3.10.

Plinth electric convectors Megador Standard version 3.10 features: intuitive power adjustment interface; the possibility of mechanical damage to the fuse is excluded (it is moved to the control board in the device case); end caps are aligned with the legs and are made of special plastic, which eliminates scratches on floor coverings at floor installation convectors.

BUY / ORDER plinth electric convector Megador

Megador Light (MF)

Heaters with power regulation by 100% or 50%.

Megador Conner

Corner convectors with power regulation from 100 to 400 W.

Megador Group (MG)

These models of convectors can be combined into a chain. Require additional installation thermostats. Standardly produced with moisture protection IP20, on request with IP44.

Megador Aroma (MWA)

Models of this series with aromatherapy (with a flask for aroma oils), with power regulation from 100 to 600 W.

Megador Aroma heaters are produced in white or brown. The connection side can be left or right.

Greenhouse heater Megador MT-150

For a greenhouse measuring 6 x 2 meters, the manufacturer recommends two of these heaters.

Operating principle of the Megador plate heater:

The heater installed near the wall (in the plinus zone) evenly starts to warm it up. The temperature of the wall surface becomes higher than the air temperature inside the room. In addition, a heated wall essentially becomes a heater with an incommensurable large area heat transfer than a convector. As a result, the heat of the heated air in the room is not transferred to external environment(through the enclosing surface with a higher temperature). This makes it possible to ensure a uniform temperature even in places with high heat losses and reduce energy costs by up to 40%.

You can heat your home today with the most different ways. On sale for this there is a huge number of devices that work according to the old, familiar methods, and those that have been introduced quite recently and developed with the latest energy-saving technologies. The market is full of electric convectors of the most different models and manufacturers, infrared heaters, batteries with boilers and other heating devices. More recently, it has become possible to buy skirting convectors.

Electric baseboard convector: design features

Everyone knows that a convector is a heating device that works on the principle of natural convection. The heating element built into it heats the air and it rushes up and displaces colder masses on its way down. A kind of air circulation is created, and its gradual heating. An hour or two after turning on such a device, the rooms heat up and become noticeably warmer.

The plinth heating convectors that appeared on the market today made it possible to solve the problem of bulky heating equipment. They are distinguished by their miniature size. This makes it possible to install them where a plinth usually stands in close proximity to the floor. At the end we get excellent baseboard heating, effective and attractive in terms of design.

Dimensions skirting heating convectors:

• Their height varies from 60-250 mm;
• The thickness reaches 90-100 mm.

Already today on sale you can also find units that practically do not stand out from the wall. However, it should be understood that the power of convective skirting boards directly depends on their size.

Rating of companies producing skirting convectors

A plinth electric convector is a heating appliance, the main part of which is a heating element with a large finned area. It heats the air with the help of an electricity bill, and is extremely simple design. It contains temperature control sensors, although some models can be controlled by the main control system.

Electric baseboard convectors are intended for heating both private houses and commercial premises where there is no possibility or need for laying conventional heating, such as water, or areas where there are no gas mains.

However, it is no secret that this species heating will be expensive. Monthly expenses for such convectors will be incredibly high. Having made a simple observation and calculation, you can see that for heating a room with an area of ​​100 sq. m. it is necessary to install equipment with a capacity of 10 kW. Such a device will consume about 240 kW of electricity per day. Translating them into a cost, you will see that with the cost of electricity in the range of 4-4.5 rubles / kW, you will need to pay about 1000 rubles daily. A cheaper alternative to electric units are water models. They can be connected to more economical solid fuel boilers and thus reduce heat generation costs.

• Carrera;
• Noirot;
• NeoClima Comfort;
• Electrolux;
• Daewoo Electronic.

All the companies presented above produce both electric and water type heating convectors.

Skirting heating convectors: the pros and cons of equipment

If you are not afraid of the high cost of paying for electricity in the presence of electric convectors, or if you are still attracted by one of the varieties of liquid convectors, you need to familiarize yourself with the specifics of the equipment and its advantages.

These include:

1. diminutiveness- dignity, which is noted in the first place. It is due to the compactness of the devices that they are valued in the market. This type of heating allows you to completely hide the heating system, and apply any desired design solution in the room.
2. Safety for others. This equipment is perfectly protected from possible accidental touches. This is especially valuable where there are small children, or people with visual impairments.
3. Comfort temperature indoors at any height. This type of heating works in such a way that there is a uniform distribution of air over the entire area of ​​\u200b\u200bthe room.
4. Rapid heating of the room. Thanks to a well-designed design, the air in the room heats up quickly and rapidly spreads throughout the room.

The disadvantages of this type of devices include their high cost, low power devices, which is not enough for all areas. modern houses. Sometimes skirting convectors have to be laid along all walls. Also, some are afraid of the complexity of installing this equipment. However, the latter can not be considered a disadvantage, since in fact there is no difficulty in installing plinth heaters with your own hands.

Plinth type convectors: installation features

Installation of plinth convectors for water consists in installing equipment along the walls and laying connecting pipes to them. plastic pipes. The compactness of the equipment during its installation creates some difficulties. In addition, the devices pass close to the floor, which also causes inconvenience. In addition, the integrity of the system involves the passage of corners and walls, which will also make you a little tricky. However, such work is not particularly different from laying the usual nm heating system with batteries and a boiler. You can choose either a one-pipe or two-pipe system.

If necessary this system heating may not be the main one, but additional, and be used in conjunction with other heating devices. Very often it is installed in conjunction with such a type of heating as underfloor heating or conventional water batteries.

There are some rules that must be observed when installing baseboard heating. They will help the system work more efficiently and you, extend the life of the devices.

Features of installation of skirting convectors:

• Do not install plinth electric convectors in places where water can get on them.
• Keep in mind that electric skirting convectors are not very light. They must be firmly attached to the wall.
• Each electrical unit must be equipped with a separate electric outlet, ideally for the equipment it would be good to draw a separate line.
• IN without fail consider having circuit breakers.
• When installing, there should be a distance of 15-20 mm between the batteries and the floors. So nothing will interfere with the intake of cold air from the room.
• When placing water appliances, carefully check all connections for leaks.

When installing electrical appliances, grounding must be used, which will prevent accidental electric shock in case of equipment damage or breakdown.

INFORMATION ABOUT THE TS CARNOT BOARD CONVECTOR

Modern heating devices - plinth convectors, leave no chance for the cold. After all, they start heating just from the coldest parts of the room and, thanks to the use of the convection principle, quickly warm it up even in remote corners.

The skirting-type convector today is one of the most "invisible" heating devices, successfully competing in this matter with a warm floor. As the name implies, it is located in the place where the plinth is usually placed. Thus, the water plinth convector warms up not only the air, but also the floor and walls. Its advantage over a warm floor is obvious - the air begins to warm up as soon as the heating is turned on. You don't have to wait for heat to break through the flooring, which may have insulating properties like laminate or tile. The plinth convector does not create any barriers to heat, because the grate, which closes the body with water-containing tubes, is purely decorative, without interfering with heat transfer - it freely passes through the slots in it from above warm air and sucked in cold from below.

Water skirting convectors- absolutely safe heaters. The temperature in them does not rise to such a point that wallpaper, textiles or other easily combustible materials could ignite and you will not be able to burn yourself. Therefore, you can move furniture close to skirting convectors, place them under long curtains, upholstered furniture, plastic panels- in general, arrange interior items as in the case of ordinary skirting boards.

The power of the baseboard convector depends on the parameters of your room. For heating square rooms more powerful water skirting convectors are required than for narrow elongated rooms, such as corridors, since in the latter case the ratio of perimeter to area implies a longer skirting board.

The better the thermal insulation of the room is, the less power the skirting convector needs to short time bring the temperature to the optimum level.

Thermal plinth TS CARNOT

"Thermal plinthTSCARNOT" is a new progressive heating system based on the so-called "fireplace effect".

Streams of warm air ascending from the baseboard evenly heat the walls of the room, which, as they heat up the entire surface, radiate heat, as a result of which the most even distribution of heat in the room is achieved. "Thermal plinth" combines the advantages of underfloor heating and classic radiator heating, but does not have their shortcomings.

If you decide to order a TS CARNOT thermal skirting board, we will help you choose the optimal color and texture solution so that the heater does not get out of overall design your premises.

The decorative part of the TS CARNOT thermal skirting board can be chosen to match perfectly with laminate, parquet, floorboard, porcelain stoneware and tiles, carpeted, self-leveling floor - in general, all the materials that are used today as floor coverings. You can also choose any wall decoration. Providing comfort and warmth in the room, thermal plinth will not interfere with the solution of aesthetic problems, no matter how original they are!

In addition to constructive and energy advantages, the thermal plinth also has purely practical advantages. By installing such a convector device, you will be relieved of the need to specially deal with cleaning the heater. Washing or vacuuming the floor, walk along the baseboard convector - and it will always look neat and clean.

As well as big amount models of heating electrical appliances can be identified the most modern version- this is a plinth with an electric or water heating element. High efficiency, ergonomics and safety attract more and more consumers. This modern system uniform space heating around the perimeter. Skirting convectors help to keep the style of the room without drawing attention to its design.

Minimalism is modern style which is popular. To minimize the presence of interior items, to increase space is the desire of many Russians. The use of skirting convectors allows not only to effectively heat and maintain the required temperature in the room, but also not to clutter up the walls.

The structure of the unit consists of heating element in the form of two copper pipes, if the heating is water (Fig. 1) or cables with copper plates, if the convector (Fig. 2). In the area of ​​\u200b\u200bthe plinth, at the junction of walls and floors, a mount is made that closes aluminum box.

The outer case can be painted in any color that matches the interior as much as possible.

Operation features

Principle of operation of this type convector is different from others heating devices. It is known that the lower the heat source is, the more effective the heating process will be. Cold air is heavier, and when heated, it rises, passing through the interior items in the room. In the case of a baseboard heater, there is also wall heating which have their own heat dissipation. Thanks to this property, there will never be a temperature drop in the room. different zones, which significantly increases the efficiency of the convector.

The operation of the plinth device allows you to create a favorable microclimate and prevents overheating of the air in the room. To date, this is the only device that allows you to make the temperature in the entire room the same, from floor to ceiling. Given the small-sized design, it practically does not stand out against the general background. Due to the construction of business centers and residential buildings with improved planning, this device is of great relevance. fashion trend do indoors big windows on the entire wall implies a maximum covert communication. In this case, the skirting electric convector is perfect solution heating system in creating a modern design of the room.

Advantages and disadvantages

The operation of the heating system by means of skirting-type convectors does not require serious Maintenance, but there are some nuances. However, the use of any heating elements can have advantages and disadvantages, and the baseboard convector is no exception. The main advantages of a warm skirting board are the following:

1. Not a source of dust accumulation due to the closed outer casing.
2. Affordable cost compared to other electric heaters.
3. Easy installation and operation.
4. The compactness of the device does not interfere with the location of interior items.
5. emphasizes modern design creates an aesthetic look.
6. hinders fungus formation. Since the heating system warms up the walls well, high humidity is not allowed.
7. Ideal for rooms with high ceilings and large windows.
8. High speed of air heating due to heating around the entire perimeter at the same time.
9. Safety: no direct contact with the heating element.

If we talk about negative side using such a heating system, some points can be noted.

1. The presence of financial costs for installation, as the system runs round. How more area premises, the higher the installation cost.
2. High price energy resources.
3. At technical failure on the separate area the entire heating system may fail. Only an electrician can identify the place of damage to the cable and eliminate the defect. It is not safe to search for the cause of the blackout on your own.

Installation of a skirting convector

When installing an electric baseboard convector, it is important to keep in mind a few important points: efficiency will be maximum if all installation rules are observed.

1. The performance of the device will be achieved when installed at a height of no more than 1.5 cm from the floor. A level surface is essential for installation.
2. Connecting the heating unit to energy resources dictates compliance technical standards And rules fire safety . It is necessary to clearly calculate the power, composition and cross-section of the cable, as well as correctly redistribute the load. For each device, a separate outlet and automatic machine are output, and the cable is grounded. It is also worth comparing the total load in the room and the quality of the electrical wiring that serves all electrical appliances.
3. To save energy, the products can be equipped; if they are not available, the device can be separately supplemented with a climate control system.

Water skirting convector during installation

The use of this type of convector in rooms with cabinet furniture exposed around the perimeter will not only be inefficient, but also contraindicated. From warm air currents wooden elements interiors will dry out and lose their integrity.

In general, the installation of a plinth convector will not cause much trouble, since all necessary elements to connect and start the heating system. Considering all the features of the technical parameters, we can conclude that these types of convectors can be widely used not only in the residential area, but also in commercial. They can be especially popular in greenhouses, greenhouses and other places with a large number of windows.