Cleaning, flushing of industrial boilers and repair of the circuit is one of the services that we provide to regular and new customers. Our specialists will competently perform chemical, hydrodynamic and mechanical cleaning, flushing of the boiler, heat exchanger and piping systems. Under influence high temperatures in a boiler device of any type, sooner or later, deposits and scale begin to form. Salt and scale adversely affect thermal conductivity, increase fuel consumption.
Timely and professional service boilers - a guarantee of uninterrupted and effective work your equipment. Boiler cleaning can be done in different ways:
Chemical cleaning boiler descaling;
Hydrodynamic cleaning washing the boiler from scale and soot;
mechanical cleaning flushing the boiler from scale.
For selection best way boiler cleaning, correct selection equipment and reagents, it is necessary to contact specialists.
By contacting GLOBAL-ENGINEERING LLC, you can also order the processing of the boiler apparatus hydrodynamic method. This is a physical action on deposits in boilers using a high pressure water jet. The possibility of mechanical damage to the internal surface of the system is completely excluded here, which cannot be guaranteed in the case of using other mechanical methods. Our masters have everything necessary fixtures for pre-start purge and flushing of the steam boiler by the hydrodynamic method. This is one of the most effective ways to rid the boiler of dirt and scale. Hydrodynamic cleaning boilers are flushed with water under high pressure using special equipment for flushing (special pumps, fittings and other devices). To remove heavy deposits, a device is used over high pressure(ASVD).
The main condition for high performance and full-fledged functioning of boiler equipment is regular flushing of deposits. Chemical washing is usually applied to both household and industrial boilers. Minimize the corrosive effect on metal parts possible only with proper monitoring of the state of the boiler unit. If you neglect regular cleaning of the system, the heating capacity of the boiler will decrease, and scale will form on its inner surface.
Scope of work during chemical washing of the boiler:
What do you get as a result of flushing or cleaning the boiler:
Prevention is The best way avoid unscheduled, and therefore costly repairs or, even worse, a complete replacement of equipment.
Our staff employs qualified and experienced employees who know their business, so flushing the boiler will not be difficult for them. We are always ready to help you, so if you have any questions, you can contact our managers who will answer your questions 24/7. Entrust the cleaning of the boiler to experienced professionals. Contact a reliable engineering service company.
There are two types of descaling from the boiler heat exchanger - cleaning of corrosive deposits from the system and the main heat exchanger of the boiler and cleaning of solid deposits.
A flushing station with a tank is connected to the heating system, in which the chemical is located, which is mixed with water of the required concentration and distributed through the heating system. The pump distributes these chemicals at high speed through the boiler heat exchanger. This dirty liquid is pumped out of the return at high speed and replaced with fresh water to ensure sufficient chemical flow. This mixture is in turn drained and replaced with new water and corrosion inhibitor. The whole process takes several hours.
Scale in the boiler heat exchanger is removed when the heat exchanger accumulates a significant thickness of calcium on its surface, and it isolates the water from the heat source, thereby reducing performance.
This effect occurs only in the heat exchanger in which there is tap water. AT closed systems there is a lot of content a large number of calcium. There are always two ways out, either it is necessary to replace the old heat exchanger with a new one, or to remove scale with acid. Descaling with acid is considered a simpler and cheaper procedure.
Why is it necessary to flush the boiler heat exchanger?
Boiler flushing is effective way removing sediment and dirt, and what builds up inside your heating system over time. If you notice a gradual decrease in the efficiency of the boiler, this sludge envelops the internal pipelines and reduces the circulation of the heat carrier in the heating system.
Sludge and scale are formed mainly in old boilers or when replacing an old boiler with a new one in older systems. If you have replaced the old boiler with a new one, dirt still remains in the heating system, and when starting up, all the dirt can get into the new boiler, which will reduce its efficiency and service life.
Some problems that can be avoided by flushing:
As a result of washing the boiler, you will receive:
What causes scale to form on the boiler heat exchanger
The heating system includes a boiler, radiators, and connecting pipes. This system is filled with water, which is heated in a boiler and circulated by means of a pump through the radiators. Water carries dissolved oxygen, which reacts with metal in radiators and pipes as metal oxide. This water may also high level calcium and other minerals that come from the plumbing. Over time, the levels of these impurities can increase and cause problems for the entire heating system. These contaminants can form deposits inside radiators, which can reduce or shut off flow. hot water to these radiators. These impurities can form a layer on the inside of boiler heat exchangers and reduce the efficiency of such boilers. If this is not stopped and the heat exchanger is not flushed, the layer will grow and the boiler will begin to make noise when it is working.
Contact our office and we will flush the boiler heat exchanger at affordable prices.
№ | Name | Unit. | Price, rub |
1 | Chemical flushing of a wall-mounted boiler - one circuit of a bithermic heat exchanger. (Additionally paid: reagent (500 ₽/liter), neutralizer (300 ₽/liter, ~1 liter required for every 25 kW) | PCS | 4500 |
2 | Chemical flushing of wall-mounted boiler - heat exchanger heating system. (Additionally paid: reagent (500 ₽/liter), neutralizer (300 ₽/liter, ~1 liter required for every 25 kW) | PCS | 4500 |
3 | Chemical washing of a wall-mounted boiler - hot water heat exchanger. (Additionally paid: reagent (500 ₽/liter), neutralizer (300 ₽/liter, ~1 liter required for every 25 kW) | PCS | 2850 |
4 | Chemical flushing of the floor boiler. (Additionally paid: reagent (500 ₽/l), neutralizer (300 ₽/l, you need ~ 1 liter for every 25 kW), it is desirable to have an organized drain into the sewer and an inspection hole) | ||
4.1 | Boilers from 30 to 49 kW | PCS | 14000 |
4.2 | Boilers from 50 to 99 kW | PCS | 17000 |
4.3 | Boilers from 100 to 149 kW | PCS | 23000 |
4.4 | Boilers from 150 to 199 kW | PCS | 30000 |
4.5 | Boilers with power from 200 to 250 kW | PCS | 36000 |
4.6 | Boilers from 300 to 499 kW | PCS | 58000 |
4.7 | Boilers from 500 to 999 kW | PCS | 76000 |
4.8 | Boilers from 1 to 2.4 MW | PCS | 120000 |
Some salts are released from the water during its heating and evaporation in the boiler and settle on the inner walls of the heating surfaces in the form of a dense, hard-to-separate scale, which impairs heat transfer through the wall and can cause metal destruction as a result of overheating. Other salts precipitate in the volume of boiler water in the form of fine suspended particles, which leads to the appearance of a mobile sediment in the boiler, called sludge, which can also cause a boiler failure.
To prevent the formation chemical elements and scale, it is necessary to carry out a complete cleaning of the boiler equipment every 2-4 years:
Saving your business budget
To order
(including cost of reagents)
The most common and most economical way to clean the boiler, which does not require high costs, fully meeting all cleaning standards. This method requires stopping the heat exchanger, cooling it, draining water and partial disassembly. Mechanical cleaning of the boiler is carried out using the EKR-2 unit and a mechanical tool.
Mechanical cleaning of boilers from scale is carried out using two types of tools. Hand tools - scrapers, scrapers, metal brushes. Mechanical tools include non-spreading and spreading heads driven through a flexible shaft from a two-speed asynchronous motor or air turbine. During mechanical cleaning, first of all, the walls of the drums and collectors are cleaned. To do this, use special heads OP (open surface).
The heads of the OP are equipped with cutters mounted on the axis. When rotating by an electric motor or an air turbine, the cutters rotate together with the head, cleaning off scale from the walls against which the head is pressed with its teeth. OP heads are one-, two-, three- and four-row.
Descaling with application hand tool carried out in places inaccessible for cleaning mechanical tool(at the corners of the joints of the partitions, near the protruding ends of the pipes, etc.).
Descaling with a hammer sharp ends, the so-called clavicle, is strictly prohibited, since it damages metal surface drum to a depth of 0.5 ... 1 mm, which favors increased corrosion.
The surface cleaned with a manual or mechanical tool is washed with a stream of water, and then the quality of cleaning is checked. Screen and boiler pipes are cleaned after drums and headers. For this, other heads are used, which differ from the heads of the OP in that the axes of the cutters are attached to the head on hinges. When the head rotates, these axes, together with the cutters, diverge to the sides due to the action of centrifugal force, press against the pipe wall and clean it of scale. Such heads for cleaning pipes are called spreading. In all cases, pipes are cleaned with cutters while simultaneously washing the places of cleaning with water. In this case, the cutters are cooled and scale is washed off, which clogs the space between the teeth of the cutters. During cleaning, the flexible shaft must not be passed into the pipe below the fixed collar. This is necessary in order to prevent the head from leaving the lower end of the pipe and breaking the cutters.
To order
(including cost of reagents)
This method of cleaning allows the cleaning of heat exchange units (boilers of all types, heat exchangers, boilers, coolers, cooling jackets of compressors, etc.) from scale without the need to disassemble the unit. It also allows the cleaning solution to penetrate into all hard-to-reach places unit, which allows for a more thorough cleaning of heat exchange surfaces.
Individual selection reagents, as well as the concentration of the solution, washing methods, depending on the physical and chemical qualities of the scale and the material of the heat exchange surfaces, allows washing without damaging the units.
The flushing scheme is developed individually for each specific unit, depending on the reagents used, the technology and the degree of contamination. It includes expansion tank, chemical pump, piping, boiler connection, removal piping carbon dioxide, released at chemical reaction. Heating of the solution can also be provided, depending on the washing technology.
The technology of chemical cleaning of boilers requires compliance with strict safety regulations due to the use of acids, alkalis, and other chemical additives in the process. Chemical cleaning produced under the guidance experienced professionals. The flushing process is controlled by regular taking of chemical samples of the solution for the presence of active hydrogen ions, the mass content of iron and other metals in the solution, from which the heating surfaces of the boiler unit are made. Chemical analysis before cleaning is carried out to exclude chemical damage to the heat exchange surface.
After chemical washing of the boilers, the active residues of the reagents are neutralized, the washed surfaces are passivated, and they are chemically coated with an anti-corrosion layer (phosphating).
Waste solutions are neutralized, brought to sanitary norms and drain into the sewer. The reagents used by us for cleaning boilers do not contain salts. heavy metals and are biodegradable.
To order
(including cost of reagents)
This method of cleaning boiler equipment consists in the destruction of deposits and their simultaneous removal from the surface being cleaned with high-pressure water jets supplied to working area from the high-pressure pump through special nozzles, using a high-pressure hydrodynamic unit.
Depending on the type and condition of the equipment to be cleaned, the GUVD operator can change the pressure value from 0 to 630 atm and the water flow rate up to 4.5 cubic meters. m per hour, while cleaning occurs without violating the integrity of the equipment being cleaned, with the greatest efficiency, productivity and quality.
Effectively removes any deposits, regardless of their physical properties, chemical composition and spatial location. A more gentle method that does not damage the surfaces of the machined equipment. Does not occur during cleaning overpressure in the tank being washed itself, which eliminates damage to the sealing elements and units of the equipment being processed.
The use of ultra-high pressure systems makes it possible to increase the productivity of cleaning operations by dozens of times and thereby reduce downtime technological equipment, i.e. direct and indirect economic losses. Ecological cleanliness and safety technical process guaranteed. When cleaning, an environmentally friendly working environment (water) is used, which greatly simplifies the disposal of processing waste.
3.1 Hot water boilers (kW) |
|||
---|---|---|---|
mechanical |
chemical |
hydrodynamic |
|
Low power (Baxi, Feroli, Viessmann, Boderus, Vaillant, Dakon) |
|||
50 - 200 kW |
|||
St. 200 - 300 kW |
|||
St. 300 - 500 kW |
|||
Medium power (De Dietrich, ZioSab, Viessmann, Wolf) |
|||
St. 0.5 - 0.9 mW |
|||
St. 1 - 2.4 mW |
|||
St. 2.5 - 5 mW |
|||
St. 5 - 10 mW |
|||
Industrial (DKVR, DE, E) |
|||
1 - 2.4 mW |
|||
St. 2.5 - 9 mW |
|||
St. 10 - 15 mW |
|||
St. 15 - 20 mW |
|||
St. 20 - 25 mW |
|||
St. 25 - 50 mW |
|||
St. 50 - 100 mW |
|||
over 100 - 200 mW |
|||
3.2 Auxiliary equipment(boilers, heaters, heat exchangers, water economizers area to be cleaned sq.m.) |
|||
mechanical |
chemical |
hydrodynamic |
|
up to 10 sq.m. |
|||
St. 10 - 25 sq.m. |
|||
St. 25 - 50 sq.m. |
|||
St. 50 - 75 sq.m. |
|||
St. 75 - 100 sq.m. |
|||
St. 100 - 200 sq.m. |
|||
St. 200 - 350 sq.m. |
|||
St. 350 - 500 sq.m. |
|||
St. 500 - 1000 sq.m. |
|||
St. 1000 - 2500 sq.m. |
Over the past few years, sales of boiler equipment have increased by several points, in particular, the demand for equipment for cottages has increased. Boilers are equipment for heating private houses and for producing steam in industry. Purchasing power for such goods falls in the warm season - in spring and summer. This is due to the fact that by the onset of cold weather, many residents want to already have a fully functioning boiler equipment. AT cold winter such a plant is in active use, and in order to prolong its operational capacity, regular maintenance should be carried out. cleaning of heat exchangers. To choose the right desired method, you need to be guided by several indicators: the quality of the water used and the type of boiler equipment. The best thing boiler flushing will be implemented with an integrated approach.
Mechanical cleaning of heat exchangers is a process of washing equipment with water, which is supplied under high pressure. In order to carry out this event, it is necessary to disassemble the boiler into parts and rinse each one well. This method allows you to get rid of even severe corrosion and scale. Mechanical cleaning of boilers - not a very common method, although quite simple and effective. Main advantages:
But we should not forget that this method requires additional time and effort for its implementation. To clean, you need to invite a specialist who has experience with such a unit. The professionalism of the worker will allow you to quickly and efficiently disassemble and assemble heating equipment.
Chemical flushing of heat exchangers happens with the help special means- reagents. For this method, you need to invite a professional who has experience in handling chemicals. He will make a solution with the required concentration, which will cope with his task. After that, the boiler is rinsed with plain water. If necessary, the process can be repeated several times. The amount will depend on the complexity of scale on the walls of the heat exchanger. Chemical washing of boilers has the following advantages:
However, this method may not always be effective. It is not suitable for removing corrosion. For more serious sediments and deposits, chemical and physical cleaning of the boilers should be used together.
At long-term operation any device or a separate part of it can fail. This needs to be repaired. The qualification of specialists will allow you to repair breakdowns of any complexity in boilers of different manufacturers. Even models of modern brands. The presence of special tools and apparatuses make it possible for quick and high-quality diagnostics of boiler equipment. No need to postpone the repair of heat exchangers for later. The sooner the repair process begins, the less time and money will be spent on it. Our company guarantees the quality of work and repairs in a short period of time.
Timely chemical flushing of boilers performed by our company’s employees will get rid of scale in cases where other cleaning methods do not bring desired result. The formation of scale on heating surfaces reduces the operating period of the equipment and reduces heat transfer. Maintenance will eliminate the appearance of defects, damage to equipment and system failure.
Chemical flushing of boilers is one of the most popular services, it is regularly performed by the company's masters. It allows you to clean surfaces heat exchange devices without dismantling the unit. The used reagent penetrates into hard-to-reach places of installation, determining the quality of cleaning.
The choice of solution, reagent concentration and cleaning method is made on an individual basis. It depends on the thickness and density of the plaque, the degree of contamination and the material. internal surfaces boiler. To carry out the work, the following equipment is required: a pump, an expansion tank, a piping system for connecting to a boiler plant and removing carbon dioxide. The procedure requires strict adherence to safety rules due to the use of strong reagents. The execution steps include the following:
As a result of the procedure, the hydraulic performance of the boiler plant is improved, fuel consumption is reduced and efficiency is increased. Metal passivation is the prevention of corrosion formations leading to large-scale destruction of the walls. Cleaning the heat exchanger prevents premature failure and associated financial costs. Regular monitoring of the chemical composition of the water used during the operation of the system will eliminate the problems that occur with excessive mineralization and violation of the acid-base balance.
Performing services for chemical washing boiler equipment, we strive to create attractive conditions for long-term cooperation. Numerous service stations managed to appreciate the responsible attitude to work and the professional level of employees. Benefits of the treatment include:
To use the service for chemical washing of boilers, just call the specified phone number or fill out the order form. We are ready to cooperate, contact us!
kayabaparts.ru - Entrance hall, kitchen, living room. Garden. Chairs. Bedroom