How to disassemble a door handle for repair or replacement. How to disassemble the door handle of an interior door yourself

To date, there are a huge number of various varieties of door handles. All of them are quite reliable, but sometimes they still have to be changed or repaired. However, a problem arises here - not everyone knows how to disassemble this essential piece of furniture in everyday life.

How to remove the door handle installed on your own interior door? Read about it below.

Reasons for dismantling

For the most part, you need to disassemble the handle if:

• she got loose;
• fell into disrepair;
• the lock needs to be replaced.

In the first case, there is usually no need to remove it. It is enough just to tighten the screws holding it, or replace them with thicker ones (if the tree is worn out).

Unfortunately, budget options handles, in principle, cannot serve for a long time, and besides, they are made completely unsuitable for repair. The coating on them is usually quite unstable and quickly climbs during operation. Therefore, when they fail, they are simply replaced with a new one.

Often, during repairs, the owners decide to replace the old handles with new ones that are more suitable for created design il just look more modern.

When buying a new set, try to choose those made from good metal with a minimum amount constituent elements. Reliable pressure models, for example, should be equipped with bearings - they can serve you for several decades. By the way, quality is very easy to determine: the heavier the fittings, the higher it is.

The most common types of door handles

Most often, handles of the following three types are installed on interior doors:

• stationary;
• nobs (round);
• pressure.

The latter variety is considered universal, since it can be equally often seen both on the front and on the interior doors. This mechanism in the normal position has an extended locking tongue, and when it becomes necessary to enter the room, the handle is pressed and it leaves the grooves. In this case, a lock usually cuts into the canvas, protected by special overlays. In order not to damage the latter, disassembly must be carried out as carefully as possible.

Round, equipped with a latch, the handle in our country is used only on interior doors. Abroad (for example, in the USA) they are often put on input. With outer side it has a hole for the key, and from the inside - a lock button.

Stationary Models installed mainly on hinged doors. This design is convenient, but not very functional. In fact, it is an oblong bar on which a U-shaped bracket is fixed. In the simplest versions, no lock mechanisms not provided - the door is closed with a separate bolt. In more advanced models, there is also a roller latch installed independently.

Prepare the following tools for dismantling:

• flat and Phillips screwdrivers;
• stop wrench (included with the product).

If the model is without bolts (that is, with hidden fasteners), then it is necessary to act in this order:

• flathead screwdriver (taking care not to damage decorative coating doors) snap off the trim located at the base;
• unscrew the screws hidden under it;
• with a persistent key, press directly on the stopper;
• remove the handle by gently pulling it towards you;
• after dismantling, unscrew the screws holding the locking mechanism.

In simpler round models, disassembly is much easier - just unscrew the two long bolts located with back side on the sides of the latch.

In this case, you just need to unscrew the screws or screws that fasten the bar to the door leaf.

It should be understood here that the replacement of this type handles must be made to a similar size. Otherwise, traces of self-tapping screws will not be able to be hidden. They are especially visible on varnished surfaces.

Separate models are bolted through the door - this method of fastening is convenient for both the manufacturer and the consumer. In this case, you just need to unscrew them from the back and both handles will be removed.

Push handle

All that is required is to remove the trim (in most models it is connected together with the handle). In more simple options you just need to unscrew the two screws from door leaf.

In advanced ones, all fasteners are hidden behind a decorative cap - it either snaps off or is screwed onto the thread. By removing it, you will have access to 3-4 screws that need to be unscrewed with a screwdriver. Don't forget to also remove the clamping screw mounted directly on the handle - it fixes the square swivel rod. After that, the disassembly can be considered finished.

Assembly nuances

Before putting the handle in its intended place, secure the locking mechanism - turn its oblique surface in the direction of closing the door.

It is important to tighten all screws and screws as tightly as possible - the better you do this, the longer they will not come loose.

After assembly, check how the mechanism works - the latch should freely enter the groove and provide a secure fit.

The door handle becomes important element in construction door block. With its help, traditional way opening/closing the door. The handle is used intensively and, to a greater extent than the rest of the fittings, is subjected to extreme stress. Its mechanical part suffers from this, its appearance, acquiring signs of wear and tear and losing its attractiveness. Over time, the need for repairs arises. But often there is nothing left but to change the doorknob.

Different models differ in appearance, method of operation, method of attachment to the door leaf. In some situations, it is not always possible to independently figure out how to remove the handle without damaging it.

When should the handle be removed?

The need to remove the handle arises when the appearance is not subject to restoration or you need to get to the mechanical part. This part is also removed to repair the lock.

• Malfunction of the foot or knob (sagging, loosening), breakage of the lock. To take off door lock mortise type, it is necessary to remove the handle. The mechanical part that returns the push or rotary handles to their original position after pressing the lever, turning the knob, is located under the decorative strip. To diagnose the cause of the breakdown and find out how to fix the handle, perform a series of manipulations. These include: parsing the part, inspecting the spring, retaining ring, stroke limiter. Often, silumin lever models break off from an accidental impact. In this case, the remnants of the fastening are dismantled.

• Replacing the old model with a more modern one. Sometimes the device is in good condition, but outwardly it looks unattractive, spoils the impression of the door block.
• Wear of decorative coating. Expensive brass models are easily restored, but a cheap item with a peeling coating cannot be restored.

How to remove different types of handles?

To determine how to remove the door handle, you need to find out what type it belongs to. specific model. Each type has its own principles of installation and dismantling.

Stationary Models

Usually made in the form of a ball (knob), staples. Models are attached to the door leaf with ties, self-tapping screws, and the latch or lock is not connected to the handle. Stationary models serve as a handle that opens the door.

Dismantling of the bracket/knob is necessary in case of damage appearance handle, loosening of the pressure lever to the decorative strip or rosette.

Round with rosette

The round knob, in contrast to the rotary model with a latch, is made of solid material and is full-bodied. Typical way fastening of such models - on one central screed using threaded winding. Removing the round handle is simple: holding the knob on one side of the door leaf with your hand, twist the knob on the other.

The knob is attached to the central axial element not with a thread, but with a side screw. In such models, there is a hole on the side of the knob at the base where the screw head is visible. Instead of a screw, there is still a latch, it is pressed, removing the round door handle from the rod.

The one-sided knob is attached to the socket. If there are no visible fasteners in the socket, then it is covered with a decorative overlay. To remove, first try to twist it counterclockwise. Usually the pad is unscrewed in 2-3 turns. If the overlay is not removed in the specified way, it means that it is put on the mounting plate using the snap-in method. The plate is carefully pry off with a screwdriver and removed, opening access to the mounting screws.

brace

Model-brackets are installed on heavy entrance doors. The bracket is more often on the bar, there are also models on the screeds. The latter include popular handles for plastic doors frequently found in office space. Mounting screws in models on the bar are often not hidden by a decorative overlay, so figuring out how to remove them is not difficult.

Important! There are exclusive models sold by the piece, as they are installed on one side of the door leaf. There are no mounting holes on the outside, since the bracket is screwed with screws with reverse side door leaf.

It is more difficult for an inexperienced master to deal with an office handle with a bracket, since it will not be possible to immediately figure out the method of fastening. It is held by a clamping nut located on the base. To unscrew it, you will first need to find a hole for the rod. It is convenient to use a thin hex wrench, a small screwdriver. The rod is inserted into the hole, the nut is unscrewed, the bracket is removed.

push model

The l-shaped file handle is becoming a popular model that is installed on interior doors. For demolition work door handle of this type, you will need a thin Phillips and flat screwdriver.

Lever handles have two types of devices: on the bar and on the socket. Each type has its own mounting features:

• Models on the outlet are available in two types: with and without a decorative overlay. Handles without a lining are equipped with open fasteners, so they start twisting immediately. In models with an overlay, the lever with mounting plate additionally held on the turntable with side screws, the holes for them are located on the side on the base of the bracket. After twisting the decorative trim, the fixing screws open.
• Models on the bar are removed according to the same principle. With an open mount, the screws are unscrewed immediately. The decorative overlay is held by a snap, so it is removed by prying it with a screwdriver.

Important! Decorative trims are made from thin metal. In order to remove it without bending it, they carefully examine it and find a small hole on the side through which it is hooked.

Swivel

Hollow knobs, sold complete with a latch, are mounted on a large-diameter rosette with a decorative strip. Despite the complexity of the design, disassembly of such models is simple.

To disassemble the door handle with an integrated latch, you must perform the following steps:

• Remove the knob;
• Remove cover;
• Loosen the clamp screws.

To remove the knob, find a hole on the side of the base through which the latch is pressed. For pressing, use a thin metal object(knitting needle, nail). While pressing the locking pin, pull the knob towards you.

Important! After successful disassembly, the handle must be correctly installed back. When reassembling, make sure that the fixing pin falls into the socket (a characteristic click is heard). To do this, the knob is rotated around the axis. Otherwise, with a sharp opening, it may remain in the hands.

The decorative strip is fastened with thread or snap-on clips. It has a hole for the possibility of prying. After removing the bar, it remains to unscrew the screws on the screeds.

Video how to disassemble a round handle on a socket:

It is not difficult to remove any handle from the door yourself, if you correctly determine the method of its fastening.

Do-it-yourself installation of a lock with a latch on the door is within the power of almost every man who knows how to use a tool. In this article, we will tell you how to mount and disassemble a door handle with an integrated latch yourself. In addition to textual information, the material is provided with a video that will help you better understand the work process.

How to disassemble the latch handle and dismantle the lock

Door handles with latches are convenient in everyday life, are installed on the entrance and interior canvases. The mechanism can be push (classic L-shaped version) or rotary (in the form of a ball or socket).

To disassemble the push-type locking mechanism, you must first remove the handle. On the side or bottom on it, you need to find a recessed screw and unscrew it with a screwdriver (in some cases, you will need a hex key). Then removed decorative overlay. Most often it has a thread, and this is easy to do. Having removed the panel that hides the fasteners, you can unscrew the main bolts holding the mechanism. Next, the lock plate is unscrewed from the end side of the canvas. The lock can be easily removed by pulling it towards you.

The process of disassembling a device with a rotary round handle differs little from actions with a push mechanism. In some models, the ball is threaded, you only need to hold the second handle motionless, turning the part to be removed in the opposite direction. Sometimes manufacturers supply mechanisms with screws hidden in small recesses, as in pressure devices.

In some models, you need to find a small hole on the handle. Having found it, we turn the ball so that in this recess we see a button (stupor). By pressing on it with something thin, we pull the handle towards ourselves. Often the kit comes with a special key for this. Decorative protection in such models it is usually removed if you simply pry it off with a knife or screwdriver.

Installing a Latched Door Handle

Installation is divided into several mandatory stages:

1. Determining the installation location and marking.
2. Drilling holes.
3. Mechanism fastening.
4. Box preparation.

Having determined the height of the location, mark the center of the handle. Next, the place for the latch is marked. To do this, determine the middle of the end of the door, apply the lock as it will be mounted, outline the tongue. To work, you need to prepare the following tools:

• Drill;
• Screwdriver;
• Chisel;
• A hammer;
• crown on wood;
• Feather drill;
• Spiral guide drill for wood;
• Square;
• Line, roulette.

To drill a hole for the mechanism, a wood crown is used. First, one side of the canvas is drilled, then the other. If done right away through hole, the decorative coating on the opposite side may peel off. The drill must be held at an angle of 90° during operation.

Important! For most standard models locks with latches, a feather drill with a diameter of 22-23 mm and a 50 mm wood crown will do.

The hole for the tongue is most conveniently drilled with a pen drill with a guide. The speed of the drill should be minimal, you need to work carefully. A mechanism is inserted into the resulting hole and the location of the plate is marked. In order for the lock to be located on the same plane as the end of the door, excess wood is chosen with a chisel.

The mechanism is installed in place, the plate is screwed under the latch. A square is inserted, the design of the handles is assembled, everything is tightened with screws. The last step is screwing decorative panel that hides the fasteners and firmly tightens the locking screw.

Advice. In order to screw parts of the lock with a latch without distortions, the screwing points are first marked with an awl, then drilled with a thin drill. In this case, the screws go into place easily and correctly.

To mount the reciprocal hole in the box, you need to close the door, leave a small mark from the latch on the jamb. You can smear the tongue with oil for this. Having outlined the place, we apply the overlay that comes with the lock, circle it along the contour. We drill a hole for the tongue, deepen the bar, then fasten it.

Installing a door handle with a latch with your own hands is not difficult, if you take your time and do everything carefully. Almost every model has an instruction, it will not be superfluous to familiarize yourself with it first. By following our advice and manufacturers' recommendations, any House master will do a great job.

How to disassemble the door handle knob: video

Door handle with built-in latch: photo

The operation of door handles leads to wear and tear. Repair required. You can call the master or carry out repairs yourself. Before doing the work, it is necessary to study the materials in order to clearly understand how to disassemble the door handle at the door. Exist different types door handles: with and without a lock. Before starting the repair, it is necessary to establish the type of product in order to determine the sequence of actions.

The market has a large selection of handles for interior and exterior doors with and without a lock. All of them are classified into three types:

To disassemble and assemble door devices tools required:

• flat or Phillips screwdriver;
• a key with an emphasis, a sharp awl;
• pliers;
• Adjustable wrench.

Reasons for parsing

Disassembly technology door mechanisms does not apply to routine work. They are carried out if the fittings become loose, it is necessary to tighten the screws in the lock, repair or change. Other reasons leading to the disassembly of fittings:

1. Product breakage. Violated performance due to failure to prevent the mechanism, rough handling. This is one of the most common causes of product failure.
2. Model replacement. The release of models is constantly being improved, there is a need to replace them.
3. Residential renovation. At overhaul the interior is being renovated. Old interior doorknobs may not fit into new style so they need to be replaced.
4. Surface wear. The product has scuffs, chips, peeling paint due to Low quality coatings. Therefore, the lock with fittings is disassembled and must be replaced.

Hardware disassembly steps

The mechanism is disconnected from the door by removing the lining in the upper part, located at the blocking button. You can remove it using the key, in case of its absence, use the awl. To do this, press on the stopper of the latch located in the fittings. The handle and the latch shaft are easily separated from the body by a simple pull. It is necessary to remove the parts and unscrew the screws with a screwdriver, the fittings move away from the door.

Disassembly of a stationary handle

If the product is fixed with self-tapping screws, then it is enough to unscrew the screws with a flat screwdriver and remove the fittings. Inspect for damage. If it cannot be repaired, then it must be replaced.
When placing the product on a common rod, it is enough to remove the fastening fragment from one side. It is necessary to take out the structure from the back side. The presence of the rod in the product is checked by turning it counterclockwise while holding the hand on the other side. If you can scroll, then it is on the rod.
The stationary handle with built-in latch can be removed with a screwdriver, unscrewing the screws and removing the decorative trim.

Lever handle disassembly

Unscrew the screws securing the cover, remove the square rod. After that, the accessories can be easily removed. The second overlay is removed, the axial rod and the rest of the fittings are removed. An inspection of the parts is carried out, and a decision is made: replace or repair.

Parsing a round pen

Knob fittings with a lock are dismantled longer than other devices due to their complex structure. However, let's figure out how to disassemble a round doorknob. To do this, you must follow the following steps:

• first, use a screwdriver to remove the flat cover located near the handle;
• we press the stopper with a key or other sharp object and pull the product towards ourselves;
• screws are unscrewed from the removal side, both parts move away from the door leaf;
• the screws securing the latch are unscrewed.

Handle Assembly

To assemble the handle, you need to perform all the steps in reverse order.

When rearranging the round handle, the latch must be inserted into the door. It should be in contact with the closed surface of the door with the oblique part of the tongue.

After installing the products, they are fixed with screws. The key mechanism is mounted on the selected side of the door.

The clamping link is located on the other side, fastened with two screws. Upon completion of installation, the performance of the product is checked. It should easily turn and return to its original place. The mechanism can be moved a little to the side and aligned. To do this, its required position is fixed, a bar is attached to the upper part decorative look.

The slot of the retainer must be in the same position with the plate rod square shape, which should enter the handle freely and without distortion.

At the end, the device is hung. It should be deepened inward by pressing against the axis of the clamping link of the fittings. The removable elements are inserted to the clamping part until it stops, a decorative bar is hung. It remains to make sure that the mechanism is working properly.

The quality of fixation of fittings is checked. It should turn freely and return to its original place. The check is carried out by turning it all the way to the stop both on the side of the latch and on the drum mechanism of the latch.

The door handle is the most necessary element for an interior door. Opening the sash - hinged, sliding, folding, without this device is extremely inconvenient, so it is a more sought-after accessory than the same lock or latch.

Door handle: classification

These devices can have quite a variety of forms, but are divided into two large groups.

• Stationary - have no connection with the lock and are installed as independent device. The handle serves only to hold it, open or close the sash. Mounted, as a rule, with screws on almost any surface. The design of the handle can be the most diverse. The most popular form was and remains U-shaped, in the form of a bracket, which is fixed vertically. If, nevertheless, there is a need to restrict access to the room, a roller latch is mounted on the sash from inside the room. The photo shows a stationary view of the fittings on the interior door.

• Push - their mechanism is somewhat more complicated. The presence of a latch requires cutting into the door leaf and the formation of a corresponding groove in the box. At the moment of pressing, the spring moves the latch tongue and the door opens. When the handle is released, the latch is in the extended position and the sash can simply be slammed shut. This method provides a tighter fit of the sash to the frame, which means higher sound and heat insulation of the room.

The mechanism provides for the possibility of emergency opening: there is a slot on the front side, which allows you to open the locked sash with a screwdriver or other flat object.

Pushers are divided into two categories.

• With a one-piece overlay-pallet - mounted through the lock. You should pay attention to the axial rod on which the fittings are put on - it should be equal to the thickness of the door leaf. The length of the element can be adjusted. In the event of a breakdown, the entire mechanism must be replaced. The photo shows a sample.
• With separate pads - installed with or without a lock. Only the size of the overlays and the size of the key hole matter here.

• Knobs - pens round shape, are a type of pressure, but may also be known as rotary. The action is similar, but to open the sash, you need to turn the knob. Usually, the mechanism is equipped with a blocking button, pressing which allows you to turn the ball on the other side of the interior door and open it. For emergency tearing, a slot is also provided on the front side of the device. In the photo - a knob-knob installed on the interior door.

How to disassemble a fixed door handle

Since its structure is the simplest, breakdowns associated with stationary fittings rarely occur. As a rule, the need to disassemble the handle arises when the owner wants to change an outdated or inappropriate design model. In this case, the actions are very simple: the screws are unscrewed with a flat-end screwdriver and the handle is removed.

A variant is possible when the fittings on both sides of the door are installed on a common axial rod. This is checked as follows: the handle is held on one side, and on the opposite side it turns counterclockwise. If the fragment is unscrewed, then the fittings are rod. You just need to carefully unscrew the first fragment, and then remove the second one from the door.

How to disassemble push handle

In this case, it will take a little more time, since it is known in advance that both fragments of the fittings are connected by one rod.

1. A screwdriver removes the screws holding the cover. The pallet is removed.
2. The tetrahedral retaining rod should be inspected. In some models, the axial element and fittings are additionally supplied with a locking rod with a cap. If this is the case, then the rod holding the element is removed, and the fittings are easily unscrewed from the axis.
3. The second fragment is removed from the web along with the axial rod. Remove the second cover first.

How to disassemble round fittings

The sequence of actions is almost the same. To disassemble the mechanism, you will need a flat screwdriver and a key with an emphasis, which is included in the lock kit. If the key is missing, any will do another object with a thin point.

1. From the side where the nob without a key is located, it is simply swivel, the cover is pry off with a screwdriver and the cover is removed.
2. Nob fixes the mechanism stopper. In order to disassemble the fittings, you should hold the stopper with a key or other object with a thin end, and remove the released fragment.
3. Using a screwdriver, both pieces of fittings are removed from the front and end sides of the canvas.
4. The screws holding the latch are unscrewed, and the mechanism is removed.

The video on how to disassemble the door handle is described in more detail.