Original DIY chandelier made from plastic bottles. Do-it-yourself lamps and lamps from plastic and glass bottles

Here is such an unusual and simple beautiful chandelier you can do it yourself with the help of multi-colored plastic bottles! We offer you a master class ...

We will need:

- plastic bottles different colors at your discretion
- scissors,
- soldering iron for processing leaves,
- thin wire for twisting twigs,
- steel wire for the frame

We cut the eggplants into pieces - the size depends on the leaves you have conceived. Then we give each piece the shape of a leaf, only your imagination is needed here ... I did something in the likeness of birch leaves.

We turn on the soldering iron. It is better to take a soldering iron with a thick tip (so there are more chances to hit the cut of the leaf, and not the fingers))), with a one-sided bevel ...

We melt the slices, so the leaves look more impressive, especially in the light of a light bulb. We also draw veins on the leaves with the edge of the sting, but carefully - they quickly melt through)))

Since the eggplants themselves are cylindrical, the leaves are not flat. The trick is that from heating with a soldering iron they warp in an unknown direction, so they look very good in the end)))

Now you need to melt with a hot needle in each leaf a couple of holes for wires. One hole is not enough, because the leaf will dangle as it pleases, under the influence of the force of gravity, but we still need the leaves to stick out the way we want)

We take a thin wire for twigs (I have a copper one, from a Soviet stabilizer))) cut into pieces 15-20 cm long. We take a leaf and thread a wire into it from hole to hole with a figure eight) ... near the leaf we twist the ends of the wires by 10-15 mm. On one of the ends we string the next leaf, starting from the extreme hole, and so on - we string, twist ...

Well, how to form the branch itself, everyone scatters it with their brains, depending on what you want ... leave the ends of the wires at least 2 cm. Take the next wire, fold in half, hook on the last leaf and twist together with the tail from the previous wire, 2 centimeters -3 ... The branch becomes thicker, already in 4 wires ...) then form the branches at your discretion, naturally, the leaves should be alternated in size and color ...

Now we need to figure out the shape of the frame ...

For me personally, this turned out to be the most difficult ... I made it in the form of a sphere ... we must also take into account the fact that in this design there will also be a light bulb, the chandelier is still ... I made a frame just with a hole on top so that the cartridge crawled through.

For the frame I took 5 pieces steel wire 60-70 cm each. I bent them in a C-shape and inserted them into an eggplant ring, leaving a 5-angled hole in the center - it turned out 10 branches ...

Well, now it’s necessary to wind the invented branches onto this structure ... It’s better to start from the bottom, and then we apply it according to the principle of tiles.

The frame had to be hung on a rope for the convenience of work - in the supine position, it seemed to me, it is simply impossible to assemble ...

The next important step is the method of attaching this creation to the ceiling. I didn’t bother, I hung it on a piece of steel wire and masked the electric wire and suspension with the same leaves ...

It looks, of course, very good even with the lamp on in the evening)))

Indoor chandelier is not only lighting fixture. Without exaggeration, we can say that she is the main decoration of the room. Handmade items are considered especially valuable. This allows you to highlight the special taste of the owners of the home, as well as an outstanding and creative mind. Undoubtedly, this species work is quite complex and requires high concentration. But at the same time, when creating decorations for your home, you can find many interesting and extraordinary solutions in it!

This article presents some ideas for decorating a chandelier with your own hands, as well as instructions for them. Everything is written so simply and clearly that anyone can do what they have planned at home.

In order to make a chandelier, sometimes they use the most unusual materials. For example, everyone is already familiar with glass or wood, plastic, and so on. But sometimes, when you want something completely “unusual”, wooden skewers, and glass wine bottles, and cans, and all kinds of tree branches, and cardboard, and even straw come into play. You need to choose depending on the idea of ​​\u200b\u200bthe creator and on the wishes of the owners of the apartment. It is also necessary to take into account general interior premises where the finished product is supposed to be placed.

An interesting idea for a chandelier made of plastic spoons

Plastic disposable spoons are one of the simplest and most readily available materials for creating a chandelier for a room. Their advantages are low price, variety colors and will serve similar material quite a long time. To create such an extraordinary chandelier, you will need a minimum of investments, both physical and material.

Materials:

  • empty bottle from drinking water, with a volume of 5 liters;
  • plastic spoons (their number depends on the size of the bottle);
  • glue for plastic;
  • old chandelier(or rather, a cartridge from her);
  • sharpened knife.

Process of creation:

  1. First you need to prepare a plastic bottle for the next steps. Remove the label in advance, cut off the bottom, dry well.
  2. Then you need to get the plastic spoons out of the package and carefully cut off unnecessary handles with a knife, leaving about 2-3 centimeters above the level of the "scoop".
  3. You need to glue the “scoops” blanks to the base of the bottle. On the left "tail" apply a large number of glue and press it to the surface (the convex side of the spoon out). It is necessary to cover the entire bottle in a circle until the entire perimeter is occupied by plastic "spoons". It is advisable to arrange them in a checkerboard pattern and slightly move them together. This will leave fewer "free spots".
  4. You need to remove the cartridge from the old unnecessary chandelier, and then place it in an already glued and dried bottle and fix it on the frame.
  5. A decorative bowl can also be made from plastic spoons: stick "scoops" around the neck of the eggplant.
  6. Install and connect the chandelier, check its operation.

Note! Possible option decorative painting or painting spoons in absolutely any color. Thus, your product will look even more beautiful and more original!

Chandelier made of plastic bottles in the form of leaves

Another unusual option a chandelier made in the form of leaves will serve in the interior. It is created from simple plastic bottles, the variety of colors of which allows you to work in the most unusual colors and embody the most daring ideas.

Process of creation:

  1. Cut plastic bottles on blanks shaped like future leaves.
  2. Each blank has to finally fix the shape of the sheet.
  3. With a soldering iron with a thick tip and a one-sided bevel, you need to slightly fuse the sections of each leaf in order to give the future product the greatest effect.
  4. In the same way, thanks to the soldering iron, you need to give the blanks a sheet structure. You need to act very carefully and accurately, because you can easily make a hole in the plastic. Such a leaf with outlined contours of veins and slightly fused edges will look complete.
  5. With a hot needle at the "leg" of each leaf, you need to melt several holes in order to attach them.
  6. Thanks to a thin wire, form branches and screw them to a steel wire frame.

Same way great idea there will be a production of a new chandelier in the form of a ceiling lamp for a floor lamp or a lamp on the table. Thus, it will be a great addition to the previous product!

Chandelier with paper butterflies

The most common version of the product is a chandelier with butterflies. And this is no accident. To begin with, this option looks luxurious and expensive, and secondly, its manufacture does not require special physical costs. Thus, even a child can participate in the creation of a chandelier.

Process of creation:

  1. The basis is either an old chandelier or a similar frame. If this is not available, then you can take the simplest wooden or metal rim. If there is no such material, then, as an option, you can take a thick wire and make about 2-3 skeins, so that a circle forms.
  2. Cut paper butterflies according to the pattern. You need to take a butterfly template and fit it to the desired size. The option also looks very unusual when butterflies of several sizes are located on the chandelier at once (again, depending on desire). Transfer the outlines to paper and carefully cut out, preferably with a sharpened clerical knife, or small non-rounded scissors. The material for the templates themselves is better to use dense, not very dirty and does not attract dust. For example, velvet paper is very bad for a product, because in the future you will need to vacuum the chandelier quite often.
  3. Take a thread from a nylon or a transparent fishing line and attach butterflies to it. You can attach it in two ways: either pierce the bodies of butterflies, or stick them on silicone glue.
  4. Next, we attach threads with butterflies to the base of the frame and decorate it.
  5. You can also try interesting option if you make a wire ball! It should be based on a suspension from a chandelier and place several butterfly patterns on it using a glue gun.

fabric chandelier

This chandelier is also based on the frame. As in the previous version, either old metal frames or dense wire are suitable for its manufacture.

After you have pre-prepared the base, proceed to cutting out the fabric from which the lampshade will be made in the future. How long will it be ready product, depends on your desire, however, it should be borne in mind that the width of the fabric must be the same as the diameter of the frame! Once you have finished the pattern, you need to try on.

Another nuance is that the top of the fabric will need to be sewn directly on the frame, which means that it (the frame) must be solid. Otherwise, if it is possible to thread it directly into the fabric, then initially it should be folded upper edge patterns and stitch, and then iron. Then we sew a seam on the side of the product.

In order for the lampshade not to lose its shape, due attention should be paid to the material. If the fabric is too light, "airy", then the bottom of the product should be weighted. To do this, you can use cardboard or fishing line.

A neatly sewn fringe, lace or braid will also look beautiful. But do not "overload" the product! The process of making a fabric chandelier is similar to making a lace chandelier. So you can safely experiment with materials that are located on the frame.

Plafond of threads and a balloon

Materials:

  • dense threads, such as woolen, cotton, or jute rope - at least 1 meter;
  • cartridge;
  • petrolatum;
  • PVA glue;
  • a brush to apply glue and petroleum jelly (it is desirable that the brush does not shed);
  • 1 or 2 pieces balloons(the first in order to work with it, and the second in order to check the finished product, if desired);

Process of creation:

  1. Inflate the balloon to a certain size, secure. Remember that the finished work will exactly repeat the shape of the ball! With a marker, draw a couple of circles at the top and bottom, in order to determine the boundaries of winding threads.
  2. Using a brush, smear the ball around the entire perimeter with petroleum jelly.
  3. Pour PVA into a plastic container and thoroughly process the threads with it (It is not advisable to apply glue immediately to the entire length of the threads! Treat them as you wind them around the ball!).
  4. Given the borders that you applied with a marker, wind the threads around the ball. Do not forget that depending on the density with which you wind, the future appearance products.
  5. After winding, you need to leave the product for a day until it dries completely; After complete drying, you need to burst the ball and remove it through the holes.
  6. Cut a place at the top and insert the cartridge.
  7. In order to be completely sure that the product turned out to be strong, you can insert a ball into it and inflate it. Similarly, you can check the flexibility and reliability of the lampshade.

Alternatively, you can paint the structure with a spray can or acrylic paint, attach all kinds of decorative ornaments such as butterflies, artificial flowers or beads. It's also a great idea to arrange a few balloons in the form of a bunch of grapes and fasten them together.

Wine bottle chandelier

This version of the chandelier is a little more complicated than the previous ones. Making a chandelier for this is quite difficult, the manufacturing process will require accuracy and care. However, you will love the result!

Materials:

Process of creation:

  1. First you need to prepare the bottle itself for further manipulations with it. The first step is to draw a straight line around the perimeter at the level you need. This is required in order to cut off the bottom of the bottle with a glass cutter;
  2. In order not to cut yourself on the glass, you need to grind the sharp edges with sandpaper;
  3. Pull the wire through the neck of the bottle and then connect the cartridge;
  4. Attach the bottle to the frame.

You can also decorate the bottle with all sorts of decorative items or leave it in original form. In any case, it will look original and spectacular.

The number of products on the frame depends on your desire. You can either leave one bottle, or fix four or more bottles at once.

Chandelier idea from laserdiscs

This idea is great for those who have a large amount left in the house. laser discs, and the hand does not rise to throw them away. It is immediately worth noting that the manufacturing options and the result can be very different. It all depends on your imagination and creativity!

Materials:

Process of creation:

  1. Make a hole in a board with a greater thickness and install a starter with a switch in it.
  2. Then connect it all to the lamp.
  3. String disks on the lamp.
  4. Install racks around discs and secure upper part.

The finished product will delight its owners for a long time, and it does not require special care. It is not advisable to place this type of chandelier in a children's room so that the child cannot harm himself (only if the chandelier hangs out of reach).

Shabby chic chandelier

To create spectacular lighting in the room, you can also make a chandelier from fabric or beads. The result is a kind of chandelier or ceiling in the style of "shabby chic".

Materials:

  • a finished metal or wooden frame (or it can be made from an old hoop, garden basket, thick wire);
  • cartridge and lamp;
  • chains and threads for decoration;
  • all kinds of beads and beads.

Working on such a ceiling is not difficult, but it is a very painstaking task. Such chandeliers usually consist of two or three levels of rings, which are located one above the other. It all depends on the size of the selected bases. If you take rings of the same diameter, then the finished product will be made in the Art Nouveau style.

One of important points consists in the fact that before starting the design of the chandelier, you need to paint and wrap the frames with decorative materials!

The approximate consumption of beads is:

  • For the lower part of the lampshade - 16 mm beads, about 15-17 pieces per thread;
  • For the upper part of the lampshade - 12 mm beads, about 35 pieces per strand.

Naturally, when stringing beads on a thread, you can increase or decrease their number or the degree of thread tension. But it is still desirable to stock up on materials in excess of the norm.

The essence of the work is to hang threads with beads "waterfall" or "cascade" so that they flow down the structure.

In order to make the effect of "muting" the light, you can sheathe the frame with a thick fabric.

A handmade chandelier will definitely bring a fresh touch, originality and beauty to the interior. You will immediately notice how the room will sparkle with new colors, and your guests will sincerely admire your creativity, diligence and original taste!

90 photos of DIY chandelier ideas

What kind of light do you like? Bright or muted, warm or cold, or maybe you like play of light or multi-colored lanterns? And how children love them! If you want to create a special light in the room or diversify the interior with an extraordinary lamp from improvised materials, read master classes on how to make bottle lamps with your own hands.




If you thought that a lamp made of plastic bottles with your own hands would look too simple, then look at the photos in the master classes and make sure that it looks charming. Everyone will wonder with amazement where you got such a designer lamp or a chandelier, and only you will know how to make such a chandelier from plastic bottles with your own hands.

What could be simpler and more refined than soft light flowing through the little petals of your night light?

Materials and tools:

  • transparent plastic bottles (bottles of any size of your choice will do);
  • white paper (you can use paper that is thicker than usual - it will hold its shape better);
  • flashlights or LED candles (for greater brightness);
  • a template or stencil of a drawing (you can download any one you like on the Internet);
  • adhesive tape (white);
  • scissors;
  • scrapbooking machine, paper knife or a special figured hole punch for cutting patterns.

Manufacturing technology

Step 1.

Let's get the bottles ready. We will use 1- and 1.5-liter bottles - this is the frame of the flashlight. We remove all labels from them and cut off the necks with scissors.

Step 2

  • We take White list and wrap the bottle around them. If any edges of the bottle stick out, then they need to be cut off. The edges of the sheet should not overlap each other - then the light will be uneven.

If you have a scrapbooking machine, take a ready-made template and do everything according to the instructions.

  • If you do not have a special stencil machine, then put on flat surface a white sheet, cover it with a stencil on top and fasten them with paper clips so that the drawing does not “go” during the translation process.
  • If you are confident in yourself, you can transfer the drawing from the stencil to a white sheet immediately with a paper knife.

If you are using hole punchers, then first stencil the pattern for the night light, and then cut them out.


Step 3

When you have cut out all the desired patterns from paper, make your flashlight voluminous - gently bend the petals away from the plane.

Step 4

Now glue the flashlight. We wrap the patterned sheet around the bottle, combine the edges and connect with adhesive white tape. A very thin strip so that the place of gluing is not conspicuous.

Step 5

We add the main element - we put a flashlight or an LED candle in the bottom of the bottle.

Here is such an original, autonomous and safe night light is ready, now you can turn off the light and enjoy this soft romantic glow!

Master class number 2. Bottle chandelier

If you've ever been talking on the phone without noticing how you painted something or cut it into pieces, then check out how this can be used to create extremely original things, like this bottle chandelier.

Materials and tools:

  • 10 small plastic bottles (transparent, one or different colors);
  • a plastic frame for a light bulb (can be found at a hardware store that sells electrical goods);
  • screws (they may be included with the frame);
  • 10 ties;
  • crosshead screwdriver;
  • big scissors.

Technological process

Step 1.

  1. We take the bottles, remove the caps (they will not be useful to us) and cut off their bottom, about a third of the height of the bottle. We begin to cut them along, as shown in the photo, 1-2 cm wide.
  2. Do not try to make even stripes, it's useless here. But it should be cut to the very neck - this is necessary for the subsequent fixing of them on the frame and among themselves.

The stripes on the bottles can be unbent in different directions - the more magnificent the lamp looks, the better.

Step 2

  1. When all the bottles are cut, we take the frame of the chandelier (frame for the lamp) and attach it as in the photo. We insert the neck between the axes and tightly clamp with two ties.
  2. We do the same with another bottle - we insert it with its neck into the opening between the other two axes and fix it. And so on, until all the bottles are fixed on the frame.

Step 3

Now you need to make sure that all the axes of the frame are closed with bottles and when the lamp is ready, there will be no gaps left. After that, you can cut the antennae of the screeds.

Step 4

Soon the lamp will shine in all its beauty - insert a light bulb into the frame and hang it from the ceiling. Like a fluffy colored hedgehog or a blossoming flower, she gives joy and a smile to everyone who pays attention to her.


These are so original - in this LESSON!

Master class number 3. Lamp - bright flowers

In addition to a chandelier or lamp, which itself emits light, there is such original solution like reflected light. And if you want to use it for your needs - you are here! This master class describes a wonderful idea of ​​​​creating unusual light using flowers from plastic bottles.

Materials and tools:

  • many bottles of any colors and volumes;
  • knife or scissors;
  • spray paints suitable for painting plastic (use combinations of your favorite colors);
  • long bamboo sticks(or any other frame for the finished flower panel);
  • old newspapers;
  • wire (gold color);
  • awl or staple.

The process of assembling a lamp from a bottle

Step 1.

Let's get the bottles ready. All of them need to be washed well along with the lids, they will also come in handy. Remove labels from bottles and clean from traces of glue, if any.

Step 2

  1. We cut off the bottom of all bottles with a knife or scissors (you can later make hearts for flowers from them). Make bottles different heights- then they will open into flowers of different diameters.
  2. Next, we cut the bottles into strips of different thicknesses up to the very neck.
  3. If the bottle is not straight, it is better to use large scissors or saw with a knife, but do not leave nicks and do not bend the bottles - the flowers should turn out neat.

The size and shape of the petals is up to you, bevel corners, make patterns - whatever your inner voice tells you.

Step 3

  1. Spread newspapers on the floor waste paper so as not to stain the floor when painting. It is better to put on gloves and work clothes before work, because the paint particles from the can still scatter.
  2. We take a spray can, a flower and start coloring. You can spray the inside of the bottle first, then the outside.
  3. Can only be painted on one side to save paint. Paint bottles without gaps, including caps and bottoms (they can be painted separately in a different color).

After dyeing, when you have achieved the desired color, set the flowers aside to dry so that they do not touch each other.

Step 4

We take the bottoms of the bottles to make holes in them for fixing. We heat the needle of the awl or the unbent tip of the paper clip on the fire - it will be much easier to make holes in the plastic. We pierce the bottoms of the bottles in two places, like a button.

Step 5

After the flowers, bottoms and corks have dried, we fasten them in various variations, your imagination rules here again! We pass the wire through the holes in the bottom and fasten it to the neck of the bottle. We simply wind the corks onto the bottles, and the wire can be wound onto the thread. This is necessary for the cohesion of the entire composition.

Step 6

  1. We fasten the bamboo sticks together with the letter X with wire. If you are using your own original frame, then arrange all the flowers on it in advance to see how it will look.
  2. We attach flowers one at a time to the cross-shaped frame with wire.
  3. When everything is ready, it remains finishing touch- attach this wonderful panel to the wall in the place where you have a light source installed. In the evening, the creation of your hands will look incredibly charming!

Master class number 4. Chandelier made of plastic flowers

If you want to always watch bright bouquets in your home, then consider this non-standard option: DIY colorful plastic bottle flower chandelier. Check out what happens and you definitely won't miss it!

Materials and tools

Plastic bottles (made of thin plastic, soft is best, they are also the cheapest);

  • spray paint of one or different colors;
  • 2 metal rings - large and small (can be bought at a needlework store);
  • scissors,
  • old newspapers;
  • gloves;
  • gold wire.

Technology

Step 1.

Let's get the bottles ready. We don't need caps. We cut off the flat part of the bottles, i.e. almost cut it in half, as shown in the photo.

Step 2

We cut the top of the bottle into strips about 1 cm wide to the very neck. The strips do not have to be even and equal in length - these will be flower petals, so you determine the shape and length yourself.

We also cut lower part bottles. The only difference is that the bottom of the bottle will be the core of the flower here. We cut all the bottles in this way and bend the petals in different directions.

Step 3

  1. We spread out old newspapers or unnecessary paper on the table, put on gloves so that we don’t get dirty when staining and proceed to the most creative part of making the lamp.
  2. We put a flower on the newspaper and spray paint on it. Can be painted on both sides or one flower different colors- as you like. The master class describes autumn bouquet, so there are more colors of orange shades.

After dyeing, set aside the flowers so that the paint dries.

Step 4

  • Let's move on to the manufacture of the chandelier itself. Take a hoop of smaller diameter, wire and a flower. Threading the wire into the neck of the bottle and wrapping the hoop, we fix the flower on the frame.
  • Then we take the second flower and do the same, pressing it tightly against the first. This is done so that the entire rim is filled with flowers for pomp.

Step 5

We attach flowers to a hoop of a larger diameter. You can create unique compositions by mixing flowers of different colors and sizes of your choice.

Step 6

  1. We easily connect the hoops together with three pieces of wire. Measure the distance between the levels of the chandelier and cut the wires with a margin for winding.
  2. First, wrap tightly around one hoop, then, straightening the wire, wrap the other end around the second hoop. You can use not wire, but, for example, twine.
  3. Measure about a third of the length of the circle along the arc of the hoop and wind the second piece of wire. After measuring another third, interlock the hoops with a third piece of wire or twine.

Check the work - if you did everything right, then there should not be any distortions.

It remains only to hang this chandelier in the most prominent place, and then all your guests and household members will feel a bit of a holiday in the house every time they look at this creation!

These are the little joys that imperceptibly penetrate your life - bright crafts, like lamps or chandeliers with your own hands, made with soul, every day then delight you and your loved ones. In addition, such original ideas can serve as a pleasant and memorable gift for one of your friends. Hurry up to create!

Photo ideas for chandeliers from plastic bottles

Look at a few more lamp ideas - maybe something will appeal to you and you will do it for yourself.







Outside the window it is cold and uncomfortable... The low gloomy sky crushes with lead weight, the last foliage flies around. Ahead of a long, long winter and bitter cold. How to return warmth and comfort to our homes? A gloomy evening will surely seem wonderful if you spend it in the company of a fascinating book, a soft blanket and hot tea - lovely little things that warm not only the body, but also the soul. cozy and warm atmosphere in the house will help to create lamps. Hang a sconce over your favorite chair, put a lamp on the table. Do not save, there should be a lot of light!

For example, we tried make a lamp out of glass bottles with my own hands . After the construction of the porch, a couple of balusters remained, elegant, figuratively carved. Why, this is an almost finished carved chandelier!

Making lamps from glass bottles

What do we need to make a lamp?

Materials:

  • balusters - 2 pcs.;
  • bottles from under "Narzan";
  • cutting boards;
  • epoxy or glue for a hot glue gun;
  • scrap metal tube d = 10 mm;
  • electrical cartridges E14;
  • light bulbs in the form of fire candles "Candle in the wind" - 3 pcs.;
  • switch for the lamp;
  • the wire.

Instruments:

  • wood saw;
  • electric jigsaw;
  • sanding attachment for a drill (cork wheel with Velcro for fastening sandpaper);
  • drill for wood, 10 x 300 mm;
  • Faustner cutters, d = 30, 45 mm;
  • core drill, d = 64 mm
  • glass cutter

The main highlight of this lamp are the original glass bottle shades and flame-shaped light bulbs.

Craft a makeshift workbench out of three pieces of wood and hold a bottle in it. Gently rotating the bottle with your left hand, draw a cut line along the bottle with a glass cutter. Do not press the bottle too hard with the roller.
Take a piece of mounting stud with a nut at the end, place it inside the bottle and gently tap the cut line from the inside.
Carefully separate the neck of the bottle from the bottom. If everything is done correctly, the cut line will turn out to be even.
Treat sharp edges with a diamond-coated glass polishing sponge or a grinding attachment for a drill (choose waterproof sandpaper, wet it when working so that glass dust does not form). You can use a whetstone to sharpen knives.
To round off sharp glass edges with inside neck of the bottle, use a drill with a grinding attachment.
Saw off 3 pieces from the balusters for vertical parts. For the side "horns" of the candelabra, saw off 2 jumpers. Make the cut at an angle.
Drill holes in the balusters for the electrical cable. Vertical details drill through.
Drill the side jumpers on both sides perpendicularly - so that the holes match.
At the tops of the balusters with a Faustner cutter d = 30 mm, drill holes for the shades to a depth of 20 mm.
Insert caps from the same bottles into these holes - then “plafonds” will be screwed into them. Fix the covers with epoxy.
After the resin hardens, sand the ends of the balusters.
From the trim of the floorboard, cut out the details for the base of the lamp. In the center of the base, drill holes for the electrical cord (use a Faustner cutter and a hole saw for this purpose).
Place a metal weight, such as a lead washer, in the base to stabilize the structure.
Process wooden details decorative composition. Suitable funds "Texturol", "Pinotex", "Aquatex", "Senezh-Aquadecor" or a simple furniture varnish.
Route through the channels in constituent parts candelabra electrical cord, connect the parts together. For reliability, insert segments into the joints metal tubes. Coat them with glue or epoxy before installation.
Assemble the center post.Attach the side horns to the center post. For strength, screw 2-3 self-tapping screws into the baluster, and drill holes for them in the central rack. Before installing, drip a little epoxy into the wells.
Connect the top and bottom of the base. Remove excess wire in the cavity of the base.
Install the glass shades on the horns of the chandelier. Screw decorative Gothic Candle lamps (also called Wind Candles) into the socket. Don't forget to install a light switch

We all love beautiful lamps. They are a great option for the visual transformation of the interior of almost any apartment. The most interesting thing is that it is not difficult to make a lamp from a bottle with your own hands. Let's look at several ways to implement such an unusual idea.

Original wine bottle lamp

DIY wine bottle lamp

Wine is one of the most popular alcoholic beverages in the world. There is no doubt that in almost every house at least one bottle is bought for every holiday.

This is interesting: After the wine is drunk, the container becomes unnecessary and is simply thrown away. Luckily, old bottles can be turned into interesting lamps that can add a magical touch to your living room or bedroom. They look especially beautiful in complete darkness. Let's find out how to make such a lamp!

Step-by-step instruction

1.Choose suitable material. Gather everything empty bottles from under the wine and select a few of the same, from which you want to make a lamp. You can take different bottles, but in this case the composition will not be complete. They can be any color. A lamp from a matte bottle will look especially beautiful and LED garland- brighter.

2.Remove the label. The label must be carefully removed from each bottle. For best results, use a sponge and warm water.

Washing wine bottles

3. We wash the bottles. They need to be well treated both outside and inside. After this step, leave the bottles to dry completely.

4. We outline a place for wires. It is necessary to mark the place from which the wires of our lamp will come out. It is better to make a hole in the side wall near the bottom. So your lamp will look much neater and more aesthetically pleasing.

5. Prepare water. We will need it in order to make a hole in the bottle.

6.Power tool. Prepare in advance the tool with which you will make our hole for the wires. The best way for such painstaking work suitable diamond crown. So you can do everything carefully, and the hole will turn out even.

Use clay to drill a hole

7. We use clay. We sculpt a cake from clay and apply it to the intended hole. During drilling, it will be necessary to occasionally slowly and carefully pour water into our hole. This is necessary so that the bottle does not overheat and crack.

8.Drilling. Drilling must be done very carefully so as not to spoil the bottle. After the end of this process, remove the clay and rinse the bottle again.

The hole must be sanded

9. Use sandpaper. In order for the hole to turn out smooth, you need to go through it with sandpaper. So you sharpen sharp edges and protect yourself from possible injury. This is also necessary in order not to damage the wires that will come out of this hole. Choose a piece of sandpaper with a grit of 150 mm.

10. Repeated cleaning of the bottle. After the work done, wash it again.

11. LED lights or garlands. Take LED lights or a garland. One-color lights will look beautiful. But you can use a multi-colored garland. It all depends on your preferences.

Insert the garland into the bottle through the hole

12. Place the lights in the bottle. Insert the garland into the bottle so that its plug comes out of the hole made.

13. Gasket in the opening of the bottle. You can use a special gasket to secure the wires. This is optional, but it will help prevent accidental damage to the wiring. In addition, with such a gasket, the appearance of the lamp will look much better.

Insert rubber gasket

14. Fix the wires. After installing the gasket, you need to fix the wires well.

15. Connect. After the work done, you can see what you got. Plug in your brand new lamp. If you don't like how the garland looks, you can gently straighten it. In order not to have to disassemble the lamp, take a thin stick and eliminate the flaws with it.

Wine bottle lamp ready

16. Done. You can decorate the bottle with decorative ribbons or strings (optional). We hope you are satisfied with the result!

Video. Glass bottle lamp in 3 minutes

There is an even easier way to create a glass bottle lamp - without drilling a hole. We offer video tutorial:

DIY plastic bottle lamp

Enough unusual lamp You can make your own from simple plastic water bottles. Such a craft will look really unique and original. Finding analogues is not easy.

Original lamp made of plastic bottles

Necessary materials to create a lamp

To make a lamp according to the scheme below, you will need several plastic bottles of various sizes. So, for the base, you can use a large bottle, for example, a five-liter one. And for additional decor- smaller bottles It is important that they have the same color and size.

The basis for the lamp from plastic bottles

In addition to the bottles themselves, you will also need to prepare an electric cartridge, a wire of sufficient length, a plug and the light bulb itself.

Important information: Traditional incandescent lamps are not a good option for our luminaire. The fact is that in the process of heating the glass, the plastic can begin to melt, releasing extremely bad smell. AT worst case it can even lead to a fire. To make a lamp from plastic bottles at home, you need to purchase only halogen bulbs (economical). Their plus is that during operation, strong heating is not observed.

Bottle lamp layout

Step one: preparing the base for the lamp

The basis of the lamp will be a large plastic bottle or a five-liter bottle. It is necessary to cut off the lower part (bottom) from it. We leave the top of the container intact, an electric wire will be passed through the neck later.

Marked base for the lamp

Then you need to measure the diameter of the necks of other plastic bottles that will be used for decoration. You can simply attach them to the main container and draw circles of the appropriate size with a marker. It is advisable to increase the diameter by a few millimeters so that later you can screw the bottles into the side holes without any problems.

Holes in bottle lamp

Helpful Hint: The easiest way to cut holes for side bottles is to use a construction wallpaper cutter. But if it is not there, you can use ordinary sharp scissors.

Step Two: Preparing Plastic Bottles for Decor

Plastic containers for decor are being prepared in the following way. First, their bottom is cut off, then the workpiece is evenly cut into thin strips (you can see the approximate thickness in the photo). The strips are cut down to the very neck - the thickest part of the plastic bottle.

We cut the bottle for the decoration of the lamp

Then each workpiece is heated over gas burner to the state of melting, it is given a disorderly and chaotic appearance. It is not difficult to do this. First, narrow strips of plastic are in any case exposed to high temperatures begin to change their shape, arching in the most bizarre way. If you want to correct the shape, use special tweezers or pliers.

Cut bottle for lamp decor

Step three: assemble the lamp

After melting, all prepared blanks from bottles are carefully screwed into the base. It remains to make a small hole in the base cover with a heated soldering iron, a special burner, or any other available method.

Reflow of plastic bottles for plastic bottle light

An electrical wire is threaded through this hole, it is connected to the cartridge. And for ease of use, you can also attach a loop folded from wire. So the lamp will be conveniently hung in the right place.

We insert bottles for decoration into the holes

At the last stage, an electric plug is screwed to the second end of the wire, but it is inserted into the threaded cartridge halogen bulb. That's all - an unusual lamp made of plastic bottles is ready to use. Hang it by the loop, plug it in and check it out!

We insert the cartridge

If you like the result, you can try to make a few more similar home lamps using plastic bottles of various colors for them. It will turn out decorative and very attractive lighting, which, due to the special decor, will reflect non-standard on the walls and ceiling of your room.

What else to read

Compliments in Estonian Russian-Estonian phrasebook: how to explain yourself in an unfamiliar country. Popular phrases and expressions for travelers....
Help Beltelecom on settlements Belarusian mobile operator "Beltelecom", under which it offers services for providing Internet access....
Exactly a month has passed since the disappearance of the schoolboy in Pushcha Alyaksandr Lukashenka's abilities could be useful in solving the disappearance of 10-year-old Maxim Markhaliuk, a resident of...