Do-it-yourself bubble panel: step by step instructions. How air bubble panels are made

Instruction

Bubble panel It is a cavity, inside of which there is a liquid, as a rule, it is distilled water. The compressor supplies air to the cavity through flexible hose, then there is the formation of many bubbles rising up with the help of the atomizer. Thanks to the installed backlight, a continuous stream of small bubbles looks bewitching and spectacular.

In order for the air bubbles to rise up in rows, and not mix, panel provide vertical transparent baffles or use transparent tubes. Directly next to panel yu install the compressor - it can be hidden in the bedside table, which serves as a stand for the panel.

Principle of operation bubble pad quite simple - through transparent tubes or a panel, air enters down with the help of a compressor and goes through the holes from the bottom up. Bubbles, rising up, produce an unusual visual effect.

Start assembling the design on, set the backlight in advance. Leave a small amount of water in the pan itself, as the column of water will stand against the water. That is, the result should be an air-drawn fountain. Don't forget the tank for draining the water pipes.

Bring the compressor to the tube, turn on the air supply - then the water will simply be thrown out of the tube. Therefore, in each tube, limit the outlet for water. By adjusting the holes, the size of the air bubbles can be formed.

Install the panels either against a wall, or in an opening, or as a partition. Please note that it is necessary to leave a gap of about 10 cm - the panels should not rest against the ceiling.

The water will have to be changed and topped up periodically, as it becomes cloudy over time and "", the walls of the tubes may become covered with greenery or bloom. Oxalic acid will help get rid of this.

Related videos

note

If necessary, the compressor can be located at some distance from the structure.

Helpful advice

Perfect option compressor location - at the top, inside the box. Then the water pressure when the device is turned off will not allow water to enter the compressor, which leads to more long work check valve.

Sources:

• DIY bubble board

Tip 2: Unusual interior with air bubble panel

Air bubble panels look unusual and stylish in any room. Thanks to the “water walls”, such a familiar substance as water is perceived in a completely different way.

Inside filled with water or glycerin, the panels rise up, twist or create a bewitching chaos of a myriad of air bubbles. You can observe their movement by developing tracking skills. Or you can just immerse yourself in meditation and forget about problems for a while.

What are bubble panels made of?

To create air-water panels, modern and simple technologies. The bubbles move between two sheets of plastic or acrylic glass, generated by compressors and passed through tubes. It uses LED lighting.

Where are water walls used?

Their ever-increasing popularity can be seen by referring to the example of famous restaurants, airports and buildings. Water bubble panels adorn the walls of the Beijing National Swimming Center, also known as the Water Cube. It hosted swimming competitions during Olympic Games in 2008. The walls of an unusual building are made up of water panels different sizes shining in the dark thanks to the LEDs.

Horizontal or vertical panels intrigue and soothe at the same time, wherever they are placed: in a commercial space, in a restaurant, office or residential space.

No less beautiful are the vertical cylindrical columns in the restaurants of Hong Kong, the Tokyo airport, or the bar counter panels in the Atlantic City casino in New Jersey, USA.

Panels and columns of different sizes, lamps, tables - all this can be found on modern market water-bubble devices to complement the interior. Panels can decorate walls, use them as partitions or put them inside the room. The entrance hall, living room and study are ideal spaces for such unusual jewelry.

What are the advantages of the water bubble panel?

Beautiful water panels are versatile because they fit any budget and look great in any space.
This is a real work of art, which is quite beneficial if you want to attract customers or add zest to the office.
Bubble panels are comparable in their function to fountains and aquariums, but, unlike them, they do not require special attention and care. All you have to do is wipe down the surface of the panels to remove fingerprints and other contaminants, and occasionally replenish the water supply in them.

Columns, lamps and tables with built-in air bubble panels will fill any space with a relaxing and inviting atmosphere.

Order or do it yourself?

Making air-water panels is very laborious. It is better to buy or order them from specialists. The manufacturer will take care to create the panel right size, style, and provide required level security. Since the panels usually use water, you need to make the box airtight. This is quite difficult. In addition, experts will take into account the wishes regarding the size of the bubbles, the speed of their movement and lighting effects.

Main Features of Air Bubble Panels

When installing a water-air panel in your home, keep in mind some of its features.

Panel sizes range from the smallest (tabletop panels) to the largest (house wall dimensions).

The main panel often consists of several compartments connected together. Thanks to this design, the air pockets are located directly inside the panel, and the air does not move randomly, but along a given trajectory.

Panels with such air supply channels are safer, as they are less likely to leak.

The panel is mounted on a base in which the tubes, pump and LEDs are hidden, that is, the entire operating system of the panel.

The panel frame is made from polymer materials.

The panel is closed system water supply, so the water supply in it must be regularly replenished.

The panel is easy to maintain, looks beautiful in any interior.

Use a soft cloth to clean the panel surface from fingerprints or grease.

Many air-conditioners are also equipped with a lighting system. The light effect that is achieved in this case is provided. Their light, the shades of which can be changed, highlights the water and air bubbles.

Some panels come with remote control which is definitely very convenient.

Sources:

• How To Build A Bubble Wall And Bubble Water Features in 2019
• Air bubble panels in 2019
• Air bubble panels. Stylish addition interior design in 2019
• Waterpanel Bubble Walls
• Water Gallery Blog in 2019

In the interior it is customary to use non-standard solutions that make the design of the room original and unique. Widespread use in this area is found by the most different materials: plastic, metal, glass. For example, an air bubble panel can be made from acrylic glass or polycarbonate. This design can not only decorate the room, but also divide it into zones.

The air bubble panel can not only decorate the room, but also divide it into zones

Air bubble panel device

The panel is a flat reservoir of transparent durable materials(triplex, plexiglass, polycarbonate), filled with distilled water, glycerin or ethylene glycol. Inside, with the help of a compressor, a lot of air bubbles are created. that are in constant motion. This design looks like a sparkling waterfall.

An additional charm of the water panel with bubbles is given by colored lighting (you can choose the color at your discretion or use the changeable mode). This decor element is found in public buildings, country houses, urban apartments. Varied Options manufacturing allow you to harmoniously fit such a partition into the living room, corridor and kitchen.

So that the bubbles do not mix randomly, the structure is divided into vertical compartments inside glass partitions or clear tubes. The backlight can have several modes, as a result of which the colors change.

What you need for assembly

Finished products are sold by many manufacturing companies, but they are not cheap. The price starts from 13-15 thousand rubles and ends with several hundred thousand. Water bubble panels at the enterprise can be manufactured according to custom order taking into account all the needs and wishes of the buyer. For those who are not ready to spend money, but have skillful hands, it is quite possible to assemble such a product on their own. For the manufacture of the structure you will need:

• two-layer polycarbonate;
• vinyl hose;
• silent compressor;
• air nozzles;
• LED backlight or LEDs;
• special glue.

Additionally, it will be necessary to make a podium, which will serve as the basis of the structure, and a cover for the upper part, which protects against dust and foreign objects from getting inside. Neon lights is the most economical, but illuminates the panel only 30 cm high, so it is installed horizontally above and below. LED lighting requires the use of an RGB controller that will control the light mode.

Design features

The structure is assembled on a pallet, having pre-set the backlight. The main element in self assembly there will be a two-layer acrylic sheet 1.6 cm thick, 98–120 cm wide and up to 7 m long. On one of the end sides, an acrylic bottom is glued with special glue, which will provide the entire structure with the necessary rigidity and sealing.

A strip is attached to the bottom with led strip or LED lighting. This is where the injection nozzles are attached. compressed air into liquid compartments. They must be of high quality and reliability in order to ensure a uniform supply of bubbles. Since the height of the water compartments is usually at least 2 m, a compressor is required increased power and with the lowest noise level. It is installed next to the structure, connected with an air hose that can be hidden in the baseboard.

A non-return valve must be installed between the hose and the panel to prevent leaks. If the compressor is mounted at the top of the structure, the installation of a valve is not required. The backlight controller allows you to create unusual lighting effects and combine or change colors. finished panel you will need to decorate around the perimeter and take care of the secure fastening of the bubble partition.

Professionals advise filling the panel with a mixture of distilled water and glycerin

To maintain a stable height of the water column, a little water must be poured into the pan. To achieve a uniform size of air bubbles, adjust the outlet holes in the tubes. The water tank can be installed either at the top or at the bottom of the panel. If you equip it with a valve, the process of changing water will be simplified.

Professionals advise filling the panel with a mixture of distilled water and glycerin. It is this composition that will provide the best "game" of bubbles.

Water needs to be replaced if it becomes cloudy or begins to “bloom”. A temporarily filled solution of oxalic acid will help to clear the internal parts of the structure from greenery.

Application in the interior

The contemplation of the smooth movement of bubbles has a hypnotic and relaxing effect, as well as the sight of a live fire in a fireplace or the peaceful murmur of a fountain. But functionally, the bubble panel can do a good job. It can be used like this:

This design item will create an unobtrusive effect of a festive atmosphere. all year round. The play of color in such panels can be considered an element of color therapy and give the owners good mood even on a cloudy day.

In fact, the phrase "do-it-yourself bubble pad" is not so surprising. Only at first glance it may seem that only a real master can build something like this. It wasn't there. Except amazing appearance, which beckons every person, the bubble panel is quite simple to construct. It will wonderfully fit into both apartment and office interior. Any room where such a miracle thing is located will forever remain a good memory for any person.

In the store, this element of decor is far from cheap, but a bubble panel made by hand will cost an acceptable amount. Of course, it will take quite a lot of effort to build an air waterfall. Before work, it is better to pre-train. Simpler and smaller designs will be an excellent warm-up for a novice master. First of all, it is necessary to understand the nature of air bubbles. Raising in space, scattering - it's all physics. Each of its processes requires certain conditions and materials. Let's deal with the latter:

Panel materials

1) Compressor without noise (a guarantee of the calming effect of the panel);

2) Atomizer;

3) Cellular organic glass;

4) Vinyl air hose;

5) Check valve, which is useful when the compressor is located below;

6) Good glue;

7) Backlight;

Actually, the design of the air waterfall is quite simple. It consists of a podium (the panel is held on it), a panel and a cover (closing it will protect the structure from dust, debris and foreign objects). Lighting equipment also plays an important role, especially at night. Different lighting provides different effects. Color directly affects the emotional background. From an economic point of view, it is better to use LEDs in the future air waterfall. Their only drawback is the propagation radius, which is only 30 cm. LED backlighting (neon lamps) is very popular. It is quite economical and highlights much better. The main thing is not to forget about a special RGB controller that will control it. Now the master's fantasy comes into play: the backlight can be located both from below and from above, both on the left and on the right. Absolute freedom of choice.

In order for the bubble panel to appear in the house, you need to take a few “steps”:

Steps to create a bubble bar

• A compressor, power supply, aeration system, check valve, backlight module and RGB controller. When the compressor is located at the top, a check valve is not needed. When the first one turns off, the water will remain at the same level as it was. No dropping down the tube.
• The design of the bubble panel is built on a pallet, which is made of organic glass. This gives the necessary visibility of the backlight. In order for the water column to be constant, you need to leave a small amount of water in the pan. Compressor tube goes down. Due to this, air bubbles enter the glass holes. Frequent problem- the accumulation of air in one heap. An acrylic sprayer with holes made will come to the rescue. Important point— regulation of outlets in each tube. This makes it possible to freely form the desired bubble diameter.
• The essential thing is a tank. You need to take care of its location in advance. After a certain time, the water will evaporate, regardless of the design of the panel. Alas, it is impossible to achieve complete tightness of the bubble panel. There are always gaps and holes. The tank can be placed at the bottom of the panel or at the top, as you wish. Highly handy thing there will be a valve that will ensure the descent of water that needs to be replaced.
• Being engaged in the manufacture of an air waterfall, you need to stock up on perseverance and patience. This is a rather lengthy process. From the master, he requires precision, because. there are many nuances in this work: the sealing of parts, the composition of the water, its illumination, located in the panel, the supply of tubes with sprayers. For a bubble pad, it is best to use distilled water. No trash or unwanted chemical substances provide long-term storage and construction work. Many masters add glycerin to the water. It allows the bubbles to better repel each other, to be separated. Special attention it is worth paying attention to its quantity. The rule of the golden mean applies here. Overshoot and undershoot will produce the same effect.

Indeed, a do-it-yourself bubble panel is a very difficult element of decor. As they say, "here you have to tinker." But making an air waterfall at home will cost an order of magnitude less than buying it in a specialized store. If you have the strength, why not try.

Dear readers, comment on the article, ask questions, subscribe to new publications - we are interested in your opinion :)

Bubble panels or bubble columns are modern facility interior decoration, which, in addition to aesthetic qualities, also has functional ones. Bubble panels are made from acrylic glass or honeycomb acrylic glass. They are filled with water and connected to an air generator, thanks to which the columns or panels are filled with thousands of air particles.

The main advantages of such panels:

• Decorating the interior and creating a feeling of boundless space.
• Relieve stress and fatigue. Thanks to the ability to change the color of the backlight, the direction and intensity of air movement, bubble panels can create an amazing atmosphere of peace and relaxation.
• Due to the fact that bubble columns or panels can relieve stress, they are indispensable in offices and help improve employee productivity.

Plexiglas made in Germany - best material for the production of such panels. It is absolutely transparent, durable and does not deteriorate over time. That is, the service life of this material is almost infinite.

Bubble columns are made from acrylic tubes filled with clear water or glycerin. Installed in arches, niches, corners and different parts rooms, bubble columns can serve not only original decoration interior, but also additional sources of lighting, stands for household appliances, supporting structures for built-in furniture. Bubble columns look especially impressive with subdued light; they can be single, integrated into the interior, lined up or in a composition - a colonnade. Such columns attract attention and help to create a unique interior of the room.

Air bubble panels keep pace with advertising and are the best engine promotion of goods in the consumer market. Our panels will help to highlight all the advantages of your products.

Air bubble panels are also used for additional room lighting. Aqua-Dream Company will produce for you an individual bubble panel based on your needs: free-standing, translucent, built into a niche or into furniture. The price of a bubble panel from Aqua-Dream is the most affordable on the market. Aqua-Dream company is a manufacturer of air-bubble panels, has own production which significantly reduces the cost of our products. Our specialists will qualitatively produce and install a bubble panel for you in the shortest possible time.

The air bubble panel is installed both in a free-standing niche, and with fastening to the ceiling or floor of the room. Also, often the panels are mounted in special niches made of drywall. At the same time, surfaces can be tiled with any materials - in this case, it all depends on the interior of the room and your desire.

Bubble panel installation is not only wonderful decorative solution but also constructive. So, such panels can be very successfully used to designate zones in a living space, as a kind of partitions. This makes it possible to avoid the need for redevelopment and create a beautiful and original decor.

You can install the panel on cabinets, against walls, as separate partitions, drywall niches. The power consumption of the panel is an average of 90 watts. As a finish, any material presented on our website can be used. Popular are materials that imitate wood, marble, fake diamond etc.

There are also ready-made bubble panels available, which the Aqua-Dream company will be happy to rent to you for exhibitions and planned events for low price. The air bubble panel will draw more attention to your display pieces. It will harmoniously fit into any interior, bringing freshness to it.

A new trend of the Aqua-Dream company is air-bubble panels built into furniture. So for example, a built-in bubble panel in the hallway will create additional lighting in a room with no windows. It will create a beneficial atmosphere in your home right from the start. Bubble panels built into the reception desk also look original, this contributes to a greater attraction of customers for your business.

The technology of the built-in bubble panel is slightly different from the panel open type, the fact that the entire system is hermetically sealed and isolated from atmospheric air. Such a panel does not require frequent maintenance and topping up with water. The disadvantages of such a system is only that it does not humidify the air in the room.

The Aqua-Dream company, in addition to everything, is engaged in the repair, maintenance and conversion of old systems to new ones. As well as the elimination of small, medium and even deep scratches on the visible parts of old panels and other plexiglass products.

Price list.

Dimensions		Panel height
		0,5	1	1,5	2	2,5	3	3,5
Width panels	0,5	25130	30800	38000	46540	52480	60390	66230
	1	31270	36960	45890	51520	57460	65370	71220
	1,2	33820	42400	48430	54060	60000	67920	73760
	1,5	46920	57900	69240	85970	97220	112700	123850
	1,8	50530	61510	78850	89570	100820	116310	127450
	2	53072	69860	81190	92120	103360	118860	130000
	2,2	56040	75690	84160	95090	106330	121820	132960

Prices are valid from 01/14/2019.

The delivery price includes:

1. Air bubble panel assembled from honeycomb PLUS GLASS, made in Germany.

2. Upper and lower boxes finished with furniture plastic.

3. LED RGB illumination on the sides of the panel with a radio remote control.

4. Silent compressor made in Germany.

5. Air supply and distribution system with adjustment of each channel.

What is a bubble bar and why is it so popular? Bubble panel - this is a kind of container, which is made of high-quality and very durable plexiglass or triplex (these are both very similar materials and have almost the same properties). In this container, air or water flows are in permanent motion and create a kind of waterfall. Such a panel special topic that it looks great in almost any room and interior. The cost of such a device is quite high, so each of us would like to do it yourself at home.

What you need to make a bubble panel

It is very easy to do it yourself, but for this you need to try hard. It is also recommended to practice well and gain skills on small structures in order to delve into the physics of air bubbles.

For the manufacture we need the following materials:

• Cellular organic glass.
• Glue.
• Noisy compressor.
• Backlight.
• Vinyl hose.
• If you decide to place the compressor in the lower area, then you will need another valve.
• The simplest and most common sprayer.

What are the design features

The bubble panel system is quite simple and does not have any difficulties, if you are at least a little versed in circuits and physics, then you should not have any difficulties. She fastened on the podium ( Bottom part), a cover that protects the system from foreign objects getting inside, and the panel itself.

The most important thing you should be concerned about is backlight. Because what color you choose, you will get such an effect. In addition, think about what colors you would like to choose for yourself. Of course, LEDs will be the most convenient and economical option.

But the only problem with diodes is that they will only shine through water by 30 centimeters. That is why most of those who make such systems use LED backlighting - in a simple way, neon lamps. But they must be equipped with an RGB controller that controls the lighting. Such lighting can be placed in any area of ​​​​the structure.

Step-by-step instructions for making a bubble panel at home

1) Take the lower half of the air bubble system, the so-called podium, and install it in this place the following components:

• airway system;
• lighting model;
• compressor;
• valve;
• power unit.

If you install the compressor near the bottom of the structure, then such a valve is not needed. After you activate the system, the water will not decrease, but will be kept at the required level.

2) The main part consists of plexiglass. Therefore, the backlight will be clearly visible through it.

3) Leave a small amount of liquid in the reservoir so that the liquid column does not move.

4) Attach a hose to the compressor through which air masses will flow into the water. It is recommended to install an acrylic atomizer so that the bubbles do not accumulate in one place. In the atomizer itself, you need to make special holes.

5) The outlets to all tubes must be adjusted by yourself. This is necessary just in order to achieve the same diameter of all your bubbles.

6) At this step, it is worth carefully considering the reservoir, through which the liquid will be added. Because it will definitely evaporate a little, because the container is leaky. Such a tank can be installed anywhere on the panel. In addition to all this, some people make a special valve for draining the liquid in order to be able to change the liquid.

The finished structure must be installed on a pallet. A beautiful backlight will be clearly visible through it. In addition, glass also diffuses light well. Leave some fluid in the system to maintain the level you want.

At the last stage, you need to properly decorate the panel. But it already depends on your imagination.