What is the difference between MDF and array in practice. Choosing a material: chipboard, fiberboard, MDF or solid wood? Facades from chipboard

The choice of material is an important point in the manufacture of furniture structures for residential, office and commercial premises. It is this factor that ultimately affects the cost, durability, practicality and safety of furniture. But how to make a choice, if in most cases both chipboard products and solid wood products look very attractive, and the price range allows you to purchase any of the options on sale for a very reasonable price? Consider all the advantages and disadvantages of each of the options in more detail.

Chipboard and natural wood: material features

It needs no introduction - this is exactly what most manufacturers specializing in the manufacture of furniture structures from natural wood think. Indeed, this material, whether it be coniferous or hardwood, has a lot of advantages that make it much more attractive to buy. High density, durability, environmental friendliness - the advantages of wood furniture can be listed indefinitely. And the many options for decorative finishes make it easy to give a bed, table or wall made of pine the look and texture of noble oak or exotic wenge.

Chipboard or laminated chipboard belongs to the category of materials obtained on the basis of recycled raw materials. It is based on sawn timber waste, crushed to the state of chips or sawdust, bonded with formaldehyde-based resins. High-quality products usually have a three-layer structure, in the center of which there are components of a larger size, and the outer surfaces are covered with more fine-grained raw materials.

The coating of melamine resins and paper is moisture resistant and allows you to give the material a decorative effect and visual appeal. It should be noted that only products of class "E1" are suitable for residential premises - furniture made of a lower-grade material is unsuitable for the manufacture of furniture structures. But most manufacturers, especially in the budget segment of the market, prefer to save on quality and safety. So, in the absence of a certificate indicating the class of material used, buying such furniture can be simply dangerous.

Wooden furniture: obvious advantages

Wooden furniture- lacquered and painted, polished or retaining its natural texture, not too flashy design. Its natural harmony and aesthetics simply does not require additional decorations, being content with what is inherent in the structure of natural wood. That is why, in most cases, manufacturers only tint the surface of furniture structures and cover it with a protective compound. Which, of course, makes wood furniture a much more environmentally friendly solution for houses and apartments than its counterparts from laminated chipboard. However, in addition to this, products made from solid natural wood have many advantages. In particular, wooden furniture:

1. Universal - suitable for any interior solutions and styles. Moreover, in interior design in the style of country, "Provence", ethnic and classical orientation, it is furniture made of solid wood that always becomes one of the central elements of the composition in the design of the space.
2. It is esthetic - for a long time keeps external attractiveness. Moreover, over the years, many types of wood only become more decorative. And fashion trends simply have no power over natural wood - it always remains relevant, regardless of the change in trends and trends in design.
3. Respectable - looks impressive and spectacular, gives solidity and aristocracy to the interior of the room.
4. Practical - it has the longest service life, is easy to restore, with proper care it will not lose its performance characteristics even after several decades.

Of course, in any "barrel of honey" there is also a fly in the ointment. For example, an array of natural wood is sensitive to changes in temperature and humidity - as a result, restoration of dried out structures may be required even before they acquire the status of antiques. Otherwise, in all its parameters, including strength, this material is superior to any analogues made from woodworking waste.

The high price of wooden furniture: myth or reality?

Wooden furniture is inexpensive - this phrase until recently seemed like a myth. Indeed, at a time when the vast majority of furniture designs were made by just a few large factories, only options based on chipboard and other similar materials were available to buyers.

Today, private enterprises are also engaged in the manufacture of furniture, which can afford to produce inexpensive and high-quality products from solid pine or birch, without deceiving the trust of customers. For example, the catalog of the Furniture Paradise company contains dozens of product items, the price of which is not too different from the prices for similar products made from wood-based panels.

So, now even those buyers who previously considered it too expensive can afford to buy wooden furniture inexpensively. Moreover, modern design trends allow you to combine classic and avant-garde interior solutions. This means that a wooden bed, a chest of drawers, a bedside table, a table or a wardrobe will be quite appropriate even in rooms decorated in a modern style, giving the room comfort and warmth, which are characteristic only of products made from natural materials.

Online store of wooden furniture: secrets of profitable purchases

Do you want to purchase really high-quality furniture designs for your home, office or hotel? The online store of wooden furniture is open to customers every day, without a lunch break, and allows you to place an order for the supply of necessary interior items online, literally without leaving your home. You just have to make your choice and make a purchase.

Of course, in the case of laminated chipboard, buyers, at first glance, have much more options in terms of choosing a color scheme. But even the brightest accents in the interior sooner or later go out of fashion. But furniture made of pine or birch, which has retained its natural color or tinted in various shades from ivory and walnut to chocolate and apple trees, will always be relevant, regardless of the change in color of the walls or flooring.

Moisture resistance is another factor that manufacturers of laminated chipboard furniture focus on. But it is achieved with the help of not the most environmentally friendly materials. But the best furniture made of solid natural wood, coated with special protective compounds, is not only completely safe for human health, but can also withstand contact with moisture, in no way inferior to its wood-shaving counterparts.

Are you afraid that in the children's room or in the kitchen, natural wood will quickly lose its attractive appearance? In fact, furniture made of birch or pine is strong enough and is not afraid of mechanical damage. And even if dents, scratches or cracks form on the surface, they can be easily eliminated with the help of simple restoration work. But the cracked chipboard will either have to be completely changed, or thrown away along with a piece of furniture that has become unusable.

Do you want to make sure that solid wood furniture designs can be beautiful, functional and modern? The online store of wooden furniture "Furniture Paradise" is ready to provide its customers with such an opportunity. Study the products presented in the catalog, evaluate the presented options for design solutions, sizes and colors. And make profitable purchases online, receiving a full range of services - from manufacturing to delivery and assembly of furniture from the manufacturer on the most attractive terms.

Today we will talk about which facade for the kitchen is better to choose and consider the pros and cons of each type. There are not so few of them, but the most popular ones, for some reason, from MDF and chipboard, that is, from sawdust ... Let's find out why.

What properties should kitchen facades have?

It is desirable that the facade was like this: set it once and forget it! It stands, does not deteriorate, does not scratch, does not fade, does not turn pale, does not get wet. In general, it serves until you get bored.

And plus to all this, it’s very good that it is fashionable and strikes the eyes of guests. But, to combine all this into one whole is almost impossible.

That's why, the best way is here: consider all possible facades, identify their pros and cons, and on the basis of this knowledge, simply choose the lesser of evils.

Well then, let's get started! The description is formed in the form of a list, while the worst options are at the bottom. That is, we start from the best of the best and move in descending order.

Facades made of natural wood

Facades made of natural wood are almost impossible to decorate in such a way that they look ultra-modern.

Wood is a classic and calm interior, without any high-tech stuff and modern trends. Country, Provence, Scandinavian style, Mediterranean, classic - these are the styles where natural wood looks the best.

And this is, without a doubt, the best option. But, if you prefer wooden facades, then you need to understand that they weigh much more than particle boards.

And this means that the base of the kitchen must also be wooden, otherwise, over time, heavy facades will simply tear out the fasteners from flimsy glued boards.

Also, it would not hurt to consider the properties of several types of wood. Because, the difference between a pine facade and an oak facade is huge. But, let's not get ahead of ourselves, now you yourself will read everything.

Pine

Pine is the most budget wood. It is easy to process, costs a little more than sawdust slabs, but at the same time, it is not very good in operation.

Particularly because pine is a soft wood that can be easily scratched. Even cat claws can cause noticeable damage, not to mention kitchen knives and other household damage.

Yes, the pine facade is subject to restoration, like any other tree. But that's extra money! From pine it is better to make the inside, and not the doors that are in plain sight.

Ash

Ash is a hard wood and is great for facades, as it is durable. At the same time, its price is two and a half times more than pine and one and a half times less than oak.

That is, if you do not have a goal that the facade looks like a natural, classic oak color, then ash is a good alternative.

His drawing and color are simpler, of course, but no worse. Even sometimes it is better when it comes to designing a Scandinavian-style kitchen, where the yellowish colors of natural wood are a priority.

Oak

The oak facade is a classic. Looking at such furniture, especially if it is not painted on top with colored paint, no one will have any doubts that this is natural wood. Oak is oak. But, for some, its natural color looks a bit gloomy.

Bottom line: the pros and cons of wooden facades

Pros:

• Durability
• Environmental friendliness
• Natural and solid look
• Possibility of restoration

Minuses:

• Expensive pleasure
• Mandatory presence of an inner box made of wood
• A little styling tweak
• There is a high probability of buying poorly dried wood, because of which the structure will quickly “lead” and cracks will appear

Metal facades

The metal front is a good thing. They are durable, very easy to care for, they are not afraid of scratches, steam, impacts or fire.

But, the cost of such a kitchen will be quite high, and also, it will not have a very cozy look.

Facades for the kitchen made of metal look more organically at enterprises than at home.

It is very unpleasant to touch them, as they are always cold. But, if you have an interior in some modern style, such as minimalism, then such material is quite suitable and will look out of place.

When it comes to metal, one more thing must be taken into account: glossy facades get dirty very easily and need to be wiped endlessly. Fingerprints remain on them, stains from a not very clean rag, and every drop of water is very noticeable.

So, if cleaning is not your forte, you should not get excited and choose such facades.

stainless steel

Facades made of stainless steel are eternal. But, this is if you do not save money and choose a good, thick sheet of metal. It should be no thinner than 4mm. And those that are thinner have a lot of disadvantages.

They do not hold their shape, they are easy to bend if something is knocked on the door. Also, they can be deformed corners, from this becoming traumatic.

Aluminum

Aluminum is a soft material. But it is lighter than stainless steel and sometimes looks more interesting. And the cost of aluminum facades is significantly lower.

But, aluminum is scratched and restoring a metal facade is quite problematic. Although, it is quite possible. In the case of aluminum, thicker sheets should also be chosen to avoid later dents.

aluminum frame

Perhaps this is the best of all the options for metal facades. Only the frame is made of aluminum, and almost any filler can be placed inside it: MDF, tempered glass, plastic.

Of course, in combination with natural wood, an aluminum frame will look very ridiculous. Still, metal obliges to modern design.

Pros:

• Durability
• Stylish look

Minuses:

• Cold to the touch
• Can be dangerous at corners
• There may be scratches and dents that are difficult to restore
• The price is not very reasonable

Acrylic (plastic) facades

Acrylic is a relatively new material in the creation of kitchen facades. In fact, acrylic is just a polymer that became famous thanks to acrylic plumbing and ... extended nails.

Their acrylic kitchens look very modern and bright. Their surface is mirror-glossy, uniform and very pleasant to the touch.

The only thing is that acrylic is a non-plastic material, it cannot be used to decorate curved, radius and figured facades. But, by and large, for design styles such as "minimalism" - this is not important, since strict, direct forms are held in high esteem there.

As for practicality, it all depends on the type of acrylic plates, which we will now consider.

The only thing that unites them is a glossy sheen, which is quite difficult to maintain in its original form all the time. Even fingerprints are clearly visible on this coating, not to mention more significant pollution.

Acrylic framed in metal

In this case, the acrylic sheet is thick enough and is not superimposed on any support, such as chipboard or MDF. But, despite this, he is afraid of a blow.

That is, if you hit such a facade well, it will certainly crack and the edges edged with aluminum will not save.

Metal edging protects only from damage to the edge.

Acrylic based on MDF board

Here acrylic is applied in a small layer and such a facade has all the properties of a conventional slab of their sawdust. That is, if its edge is slightly damaged, then such furniture begins to absorb liquid like a sponge, and the acrylic film warps and lags behind.

Restoration, as you understand, such furniture is not subject to.

Pros:

• Stylish and glossy look
• Pleasant to the touch
• More affordable than metal and wood

Minuses:

• Difficult to care for
• The surface is scratch resistant
• The surface is afraid of impact
• Not subject to restoration

Facades from MDF

Today, probably 85% of modern kitchens are made of this material. MDF is quite affordable, has great possibilities in terms of design and color, and at the same time lasts much longer than particleboard furniture.

But, among MDF there are various options for the top coating, on which their service life depends.

Painted MDF

The painted MDF facade has one indisputable advantage: it does not look like plastic and it looks more comfortable.

On the other hand, such a surface must be washed very carefully, since the coating is sometimes simply washed out under the sponge and traces of paint remain on it, and stains on the facades, respectively.

True, the painted surface is easy to restore, one has only to sand and cover the facade with a fresh layer of paint. Otherwise, this furniture is not protected from the main disadvantages of MDF. We are talking about damage to the edges and chipped edges, under which water gets in and the plate begins to “inflate”.

MDF covered with PVC film

MDF covered with such a film does not look very expensive. But then, you can wash it as you like and as much as you like. He is not afraid of abrasives. But, he is afraid of blows and this can cause chips, which then you can’t remove with anything.

Such facades are not subject to restoration.

Veneered MDF

Veneer is the thinnest shavings made from natural wood. On the practical side, veneer is no better than PVC film, and in many ways, even worse, as it is softer.

But on the other hand, veneered MDF is very difficult to distinguish by eye from natural wood. This explains its popularity.

Pros:

• Inexpensive
• Great design options
• Ability to create panel and radius facades
• Easy to care for

Minuses:

• They do not serve so long, after 5 years the edges necessarily begin to “swell”
• Not all MDF facades are subject to restoration

Facades from chipboard

And finally, we come to the worst of the worst. Chipboard kitchen facades are so bad that it makes no sense to paint these outrages.

They please the buyer for a couple of years at most, and then, the edges begin to swell, chips appear on the surface, the fittings “loose”, locks and hinges sag, since the base is too flimsy .... No, no and NO.

So which facades for the kitchen are better in the end?

Let's now try to draw a conclusion from the above information. Which facades for the kitchen are better: PVC film, MDF, plastic or more expensive options?

Of course, wood and metal are the best. But, if you choose from the available options, while similar in appearance, then the most practical option - MDF as it is the best value for money.

Negative customer reviews about popular types of facades

And here we have collected some negative reviews about kitchen facades from those who already had experience using this or that material.

We deliberately did not choose laudatory posts, as we believe that the best adviser is a critic.

We really hope that our article was useful to you. Indeed, after such a detailed analysis, you should no longer have a shadow of doubt about which facade for the kitchen is better to choose.

There are many wood-based materials that can be used in construction and interior design, but most often the choice is between chipboard, fiberboard, MDF and solid wood. Let's compare them with each other and decide for what purposes each of them is most suitable.

Chipboard

Production technology: created by pressing sawdust with formaldehyde resins. Standard thickness - up to 25 mm.

In the production of chipboard, two types of resins are used - E1 and E2. E1 is less harmful than E2 and can be used to create children's furniture.

chipboard

Production technology: the same as chipboard, but additionally finished with a polymer film.

fiberboard

Production technology: created from steamed and compressed wood dust. Standard thickness - from 2.5 to 12 mm.

When buying products from fiberboard or chipboard, check with the seller for certificates of product conformity with GOSTs. So you can be sure that the amount of harmful chemical components used does not exceed the norm.

MDF

Production technology: produced in the same way as chipboard, but using smaller wood particles - less than 1 mm. The standard thickness of an MDF sheet is from 1.8 to 50 mm.

array

Application of materials

Based on the performance properties of each material, the following conclusions can be drawn:

Chipboard is not taken into account, since it is simply a more expensive variation of chipboard that has thermal stability.

The table indicates that chipboard, MDF and solid wood can be equally used for the production of furniture. A clarification is needed here.

• Chipboard is good for the production of furniture that must withstand heavy loads in conditions of low humidity.

Do not worry about the harmfulness of formaldehyde included in chipboard. Recently, such harmful substances have ceased to be used in the production technology of this material.

• MDF is suitable for installation in the bathroom or in the kitchen. However, MDF products cannot be placed directly above the stove, as they begin to deteriorate when in contact with temperatures above 70 degrees. MDF is also used when additional decorative surface treatment is planned (for example, cutting out patterns). In a classic style, this material looks somewhat unnatural, but the “unnatural” colors of MDF are well suited for techno, modern and high-tech.
• The array requires a high-quality protective coating for wood. In some cases, it is enough to buy wood oilto protect it from possible decay and moisture. Solid wood furniture is suitable for classic and country style.

There are objectively many requirements for the kitchen facade. It must be resistant to temperature extremes and steam, unpretentious in care and, of course, attractive in appearance. Especially if you cook often or in an open-plan space where the kitchen is always in plain sight. To understand the materials and understand what to expect from different facades, from traditional solid wood to modern plastic ones, HomeGuide turned to Elena Plotnikova, head of kitchen studios at Atlas Lux Krasnodar.

If we talk about the basis for the kitchen facade, the most economical option is laminated chipboard. New generation finishes like TSS, for example, make it more durable and expressive enough to be used in a modern kitchen. More expensive, but affordable facades made of MDF. They are more environmentally friendly than laminated chipboard and more practical than solid wood - besides, they have incomparably more color and texture combinations. To the array, in addition to being a 100% natural eco-friendly material, there are also a number of questions: over time, it can dry out and deform. Suffice it to say that factories that give more than five years of warranty on their product do not work with an array in its pure form.

Elena Plotnikova, designer, head of kitchen studios "Atlas Lux Krasnodar"

How to choose a facade for the kitchen?

• First, decide on the style: a kitchen made of solid wood or with facades made of natural veneer will fit perfectly into a classic, traditional interior; into a modern minimalistic one - from MDF with a soft touch coating (literally - “soft to the touch”), for example.
• Think about practicality: a matte kitchen, even because of a small stain, will have to be washed entirely so that there are no streaks left. A glossy facade made of MDF is enough to wipe with the usual glass cleaner. At the same time, it is effective and looks expensive.

• Be sure to pay attention to the production time. In a sense, this is a litmus test that will help you understand whether you are dealing with a bona fide manufacturer or not. There can be no less than 35 or even 45 working days - the time required for proper drying of panels, gluing, painting. If they offer to do everything in a week or two, most likely they assemble the kitchen from what was stale in the warehouse. Or not dried properly.

Facades from chipboard

Artificial material does not have a high density - which means it quickly fails, especially at the attachment points. In its “pure form”, without any coatings, it reacts to temperature changes and humidity. Therefore, large factories use chipboard exclusively as a basis for different finishes. You can make it stronger (even more visually spectacular) by covering it with a film, acrylic or TSS facing layer.

Pros: low cost; a large selection of textures: you can reliably imitate wood, concrete, stone, eco-leather.

Minuses: a facade made of chipboard suggests an edge, which, firstly, simplifies the appearance of the product, and secondly, it can peel off over time. Do not install mortise handles in chipboard (standard plate thickness is 16 or 18 mm). In its "pure form" in terms of environmental friendliness, wear resistance is inferior to all materials. The facade from a chipboard cannot be radius.

Kitchen Twist with a film facade, "Maria".

• Film facades from chipboard

They can be matte and glossy, with or without a pattern. But outwardly not very impressive. Glossy PVC film is always a bit rough, pebbly - and does not give a perfect shine. But such a facade is the most budgetary. Yes, it will have an edge and only overhead fittings (no curly mortise handles), but if you need to save money, this is the best option.

• Acrylic facades made of chipboard

Acrylic is a transparent coating that is applied to a film or already painted facade. Its cost, of course, is higher than just with PVC film, but it is also noticeably stronger. Although vulnerable to severe damage - the impact will leave a chip on the top layer. Not restored.

Kitchen with acrylic facade, "Maria".

• Facades made of chipboard with TSS coating

TSS (thermo-textured surface) is, in fact, compressed craft paper, which is soldered into a chipboard base under high pressure. Reliably conveys the texture of different bases: natural wood, leather, concrete.

Kitchen Loft Industry, "Atlas Lux".

The TSS coating makes the facade even from chipboard durable, resistant to damage and unpretentious in maintenance. In addition, such a finish will not be expensive. The only negative is the edge at the end.

Kitchen Loft Vintage, "Atlas Lux".

Facades from MDF

MDF - medium density board, pressed from small dry chips. For kitchen facades, the best option: with high-quality assembly and proper care, it will safely last 10-15 years. Unlike chipboard, MDF has no edges and can be used to make radius (curved) facades.

Kitchen "Ikon" with a radius facade, "Atlas Lux".

MDF facades are painted, veneered, laminated with PVC film. You can create a glossy, matte or pearly surface in the color, shade you want, imitate wood, concrete or metal. And use not only the consignment note, but also the mortise fittings.

Kitchen "Factory", "Atlas-Lux". Facade made of MDF with a metal finish.

Pros: surface without joints up to 2.7 meters, thickness from 3 to 60 mm. Strong and durable material, can be restored.

Cons: artificial material.

Kitchen "Empire" with a glossy MDF facade, "Atlas Lux".

• Film facades from MDF

PVC film is the most budgetary option for finishing MDF: it costs an average of 20% cheaper than painted facades. This is a huge selection of textures and colors, ease of care. However, the film may peel off, deform from high (from 70 ℃) temperature - it will not be possible to restore it.

Kitchen Life with a film facade, "Maria".

• Acrylic facades from MDF

A more reliable option compared to a chipboard base - and more expensive. Such a facade can be complex in shape, with all sorts of roundings. Acrylic is unpretentious in leaving. Durable, but not strong enough to withstand a strong blow. Damage is not repaired.

Kitchen with a radius acrylic facade, "Lorena".

• Painted facades from MDF

If you are considering a color coating without an edge, then the enamel facade is the ideal solution. You can paint it on both sides, make it matte or glossy, at your discretion. With this finish, you are not limited in choosing the shade you need: 188 colors according to the RAL palette and 304 colors according to the NCS palette. Painted facades can be polished and restored.

Kitchen "Chester" with a painted facade, "Atlas Lux".

• MDF facades with fine line coating

Fine line, or otherwise eco-veneer, is a cut of natural wood of inexpensive softwoods: poplar, for example. Fine-line is flexible, inexpensive to manufacture, absolutely environmentally friendly and allows you to transfer the pattern of any wood. And it is significantly cheaper than natural veneer.

• Facades made of MDF with natural veneer

A thin slice of natural wood is laid by hand, which allows you to not interrupt the pattern throughout the entire facade. The finish can be made matte and glossy. Facades veneered with rosewood, satin walnut (red gum), olive, anegri are always unique: two completely identical products simply do not exist. This is a plus and a minus at the same time: you can’t 100% predict what the facade of your kitchen will turn out to be. Therefore, when choosing exotic breeds, ask for a sample at the factory.

Kitchen "Walensa Wood", "Atlas Lux". The MDF facade can be veneered with seven types of precious wood veneer under a glossy or matte varnish.

• MDF facades with stone veneer

They are made from natural stone (slate cut 1-3 mm thick) - or polyester resins, which are almost indistinguishable from natural material outwardly. Such a facade is resistant to temperature extremes and high humidity, attractive from a decorative point of view. It's almost impossible to damage it. The only drawback of this finish is a small selection of colors.

• MDF facades with Soft Touch coating

Matte enamel is designed specifically for surfaces that we often touch - and kitchen fronts are one of them. Soft-touch is made on the basis of rubber varnish. On such a coating there are no fingerprints, stains, scratches; it does not glare, creates a feeling of a velvety, soft to the touch surface. Practical in care: stains, traces of fat on such facades are almost invisible.

Facade with Soft touch coating.

Solid wood facades

They can be made of a solid cut of wood or with a solid wood frame, with an insert of veneered MDF. If you are considering a classic-style kitchen, both options are for you. But be warned: just an array is expensive. And not quite practical: over time, the tree can dry out and deform, especially in the south, where there is always high humidity. Although high-quality, after proper drying, the array lasts 20-25 years.

A reasonable alternative to a 100% solid wood is a frame facade, in which the solid wood frames the MDF. An MDF insert does not change its size during service, therefore such a facade as a whole is more durable and resistant to environmental influences. You can't distinguish it visually: the veneer covering the MDF insert completely repeats the texture of the solid wood frame.

The texture of the array can be emphasized with patination or completely covered with enamel: it depends on the style of the kitchen. Modern classics suggest a smooth facade without wood texture, traditional classics, on the contrary, have a pronounced pattern.

Pros: natural, 100% eco-friendly material; long lasting when dried properly.

Minuses: subject to temperature changes and humidity; expensive stuff.

Wooden beds are loved by many for their attractive appearance, naturalness, durability and ability to create a truly cozy, homely environment. However, is all the furniture that looks like wood, really, is it and does it have the indicated properties? No, not all, because due to the high cost, few decide to purchase solid wood furniture, but turn to more affordable, thus more attractive substitutes like chipboard and MDF.

In this article, we will try to figure out what modern beds can be made of, and what qualities they will have.

Solid wood beds

Let's start with solid wood furniture. In its production, high-quality, well-dried wood without knots and cracks is taken, it can be either whole boards or typesetting boards from separate pieces connected with glue (glued board), which are then sanded and varnished. At the same time, in order for the bed not to emit harmful substances, it is important that a high-quality, environmentally friendly water-based varnish is used. Beds made of solid wood are valued primarily for the beauty of texture, hardness, strength, durability. Each breed is distinguished by the individuality and originality of its pattern, shade, tangible aroma and warmth. Among different types of wood, mahogany, oak, beech, ash, birch are considered the best, since it is they who have the greatest strength, do not creak and loosen less over time, preserving the beauty and nobility of the surface for a long time.

Often, those who cannot afford expensive furniture made of precious woods choose a pine bed, which wins significantly in price. Pine has its drawbacks: it is relatively soft, so the screw connections in such furniture can loosen over time, and bumps and pits may appear in the pine boards when dried.

The malleability of natural wood has contributed to the fact that furniture from it is always decorated with a variety of carvings and patterns, which makes your bed elegant and unique. It is because of this uniqueness that it is recommended to purchase the elements of a bedroom set not separately, but at once the entire set (usually a bed, wardrobe, bedside tables, chest of drawers), because then you may simply not find components that will fit the ones already purchased.

However, an array of natural wood is a very expensive material and not accessible to everyone, so such furniture is purchased for many years, or even for life.