Technoelast top layer. Technoelast: modern materials

Technoelast TKP gray slate is a SBS modified bitumen-polymer rolled waterproofing material of Premium class with a coarse-grained gray dressing on the outside of the irulon. Technoelast TKP is produced by double-sided application of a bitumen-polymer binder, consisting of bitumen, SBS (styrene-butadiene-styrene) polymer modifier and mineral filler (talc, dolomite, etc.) to the fiberglass. Polymer films are used as a protective layer.

Technoelast TKP gray slate is used:

• for waterproofing horizontal, vertical and inclined planes
• for the installation of the upper layer of the roof in two-layer roofs
• for single layer roofing

Technoelast TKP is based on modified (improved) bitumen. Technical characteristics allow it to maintain elasticity in frosts down to -30 degrees, the service life of the material is up to 30 years. Laying of Technoelast TKP-4.0 is carried out on a dust-free and fat-free base. To do this, the base (usually a concrete screed) is treated with TechnoNIKOL No. 01 bituminous primer, then the bottom layer of rolled waterproofing is melted and glued to the base.

Marking of Technoelast TKP:

In order not to make a mistake with the choice, we suggest that you familiarize yourself with the marking:

• T - designation of the base on which the material is made, T-fiberglass;
• TO- designation of the upper protective layer of the roll (K-crumb);
• P- designation of the lower protective layer of the roll (P-polyethylene film).

Transport characteristics of Technoelast TKP

• pallet volume 1.38 m3
• pallet weight 1064.0 kg
• 20 rolls per pallet
• weight of one roll 53.2 kg
• material thickness 4.2 mm

You can buy rolled waterproofing Technoelast TKP gray slate, the price is from 185.50 rubles / m2, at our warehouse complexes in Moscow or order delivery to the site. At Technoelast TKP, the price per m2 for wholesale lots from 3001 m2 is given from the manufacturer's warehouse, for lots less than 3000 m2 - from a warehouse in Moscow, but it can also be more profitable to bring average wholesale lots from the manufacturer.

Reading time ≈ 3 minutes

Technoelast is a built-up roofing material for arranging a flat roof, protecting building structures from the negative effects of water. It has high strength, elasticity: it retains flexibility at a temperature of minus 25 degrees, plasticity - at - 40 degrees. Due to such properties, positive customer feedback, it is popular in different regions, but is widely used in the northern regions, areas with high ground pressure.

The basis of this material is fiberglass, fiberglass, polyester. They are coated with bitumen-polymer binder, coarse/fine dressing (red, green, gray) or polymer film.

Technical characteristics of technoelast

Technical characteristics of technoelast grades: EKP, TKP, EPP, KhPP:

The main varieties of technoelast

According to the scope of technoelast, the type of protective level, the following modifications are distinguished:

• Technoelast EPP- material based on polyester with a high-strength protective film. It is very strong, has an extensible lining level. They are used for the lower layer of a flexible roof, its waterproofing, waterproofing of the floor, foundation, basement, utility rooms;
  • E - polyester
  • P - film
  • P - film
• Technoelast EKP- polyester base with coarse-grained powder, a layer of polymer film. Due to its increased reliability, it is used for the upper level of a flat roof, barn roof, garage;
  • E - polyester
  • K - baby
  • P - film
• Technoelast HPP- fiberglass base with a protective polymer layer. They are used for waterproofing floors, basements, foundations, flat roofs, for vapor barrier, garage roofs, utility rooms, pipe insulation;
  • X - canvas
  • P - film
  • P - film
• Technoelast TKP- the basis is fiberglass with a polymer film, coarse-grained dressing. Suitable for the top level of flat roof, garage roof, cottage, shed.
  • T - fabric
  • K - baby
  • P - film

By appointment, 2 groups are distinguished:

• Technoelast K- for the arrangement of the upper level of the roof. For its production, shale dressing is mainly used, which protects against solar ultraviolet radiation;
• Technoelast P- when installing the lower layer of the roof. Fine-grained dressing, protective film prevent sticking of the material.

Advantages

• durability - the material is designed for service in 30 years;
• elasticity - retains plasticity with serious temperature fluctuations, can lengthen, stretch, it is allowed to weld it on building structures of various shapes;
• high quality - high-quality bitumen is used for manufacturing;
• reliability - successfully resists mechanical, air, biological influences;
• the ability to use on any surface;
• technoelast has good waterproofing, perfectly absorbs sound, retains heat;
• ecological cleanliness - does not have a harmful effect on nature, humans;
• good adhesion - artificial rubber in the composition provides strong adhesion to different surfaces;
• ease of laying, installation.

- waterproofing, built-up, styrene-butadiene-styrene modified, polymer-bitumen, roll material. It is made by applying a bitumen-polymer binder to the finished polyester / fiberglass / fiberglass base. The surface of the rolls is treated with different-grained dressings or a polymer film.

Application

Product brands

Technoelast K (EKP, TKP, EMP)- material with a coarse-grained / fine-grained powder on the front side and a polymer film / fine-grained powder on the welded side of the waterproofing sheet. It is applied as the top layer of isolation with protection against sunshine.

Technoelast P (EPP, HPP)- material with a polymer film / fine-grained powder, or a combination of them on both sides of the waterproofing sheet. Used as bottom layers in multilayer insulation of building structures(tunnels, foundations, roofs, etc.).

Material Features

• The ability, due to the properties of the bitumen-polymer binder, to restore the tightness of the waterproofing layer in case of mechanical damage (puncture, cut)
• stable thickness. During production, the exact thickness values ​​​​are set, which is a controlled indicator of the quality of the material
• Hydrophobized coarse topping (slate) provides protection against UV radiation, retains moisture

Basic physical and mechanical characteristics

Examples of using

Examples of TechnoNIKOL systems using Technoelast waterproofing

Logistics parameters

Storage

Insulation rolls must be stored in a closed, dry room at a distance of more than 1 m from heating devices. The material is arranged in one row in height in a vertical position.

Packing data

Pallets with rolls are packed in a white shrink bag. There may be 20 or 25 rolls on a pallet, depending on the brand of product. Sun-protective white packaging reduces the likelihood of overheating of the waterproofing inside the pallet, preserves the appearance and consumer qualities of the material.

The use of materials of the Technoelast series significantly increases the maintenance-free service life of facilities, as a result, they save: money, time and labor costs.

When waterproofing non-exploited flat roofs on a concrete base

Consult, clarify information about availability, fill out applications and learn about discounts

The main area of ​​application of TKP technoelast waterproofing is the arrangement of the top layer of roofing. Also quite often this material is used as a protective substrate for the lower layers of the roof.

Technoelast (waterproof lining material for TCH marking) effectively protects the roofing carpet from mechanical damage and moisture penetration. It is actively used in conjunction with other bitumen-based polymer coatings.

The basis is fiberglass impregnated with a special modified SBS bitumen. The outer side has a protective layer of stone chips and slate in gray, blue, red or green.

Benefits of waterproofing

1. Long service life - from 30 years or more. The non-decaying fiberglass backing and modified SBS bitumen can significantly extend the life of the roofing.
2. High strength providing resistance to mechanical damage
3. Insensitivity to precipitation, temperature changes
4. The cost pays off with unique features:
   • heat resistance - not less than + 100–120 ° С;
   • bituminous layer flexibility temperature - up to -25 °С;
   • fragility of the bituminous layer - up to -35 ° С;
   • breaking strength of waterproofing - 800–900 N (in the longitudinal and transverse directions).
5. Environmentally friendly material for living quarters. Technoelast TKP complies with the established sanitary and hygienic standards.

Buy waterproofing technoelast TKP

• from the factory price we deduct a part (large enough) of our dealer discount;
• we minimize the cost of material delivery;
• our warehouses work at night, because night transport is cheaper;
• delivery to the regions is carried out by factory vehicles.

We deliver Technoelast during the day and at night, various types of car awnings are possible (rear, side, top). For large orders we offer object discounts. We form prefabricated machines with different brands of TechnoNIKOL waterproofing. We successfully work with the regions.

Technoelast marking

In order not to make a mistake with the choice, we suggest that you familiarize yourself with the product labeling:

• E, T, X- designation of the base on which the material is made, E - polyester, T - fiberglass, X - fiberglass;
• P, K- designation of the upper protective layer of the roll (P-polyethylene film or K-stone chips);
• P- designation of the lower protective layer of the roll (polyethylene film);
• Number at the end of the marking indicates the weight of one m2 of material (the larger the number, the thicker the material).

Varieties of Technoelast

• Technoelast P(lining) - for the lower layer of the roofing carpet and for waterproofing works for various purposes (the inner and outer sides of the roll are protected with polyethylene film).
• Technoelast K(roofing) - for the top layer of the roofing carpet (in this case, the lower part of the roll is protected by a polyethylene film, and the upper part is protected by a coarse-grained dressing of various colors).

Technoelast based fiberglass - Technoelast HPP, Technoelast Thermo HPP, is used for waterproofing and roofing works on unloaded structures with a small slope, which do not experience high tensile and tensile loads during operation.

This is Technoelast TKP, Technoelast Thermo TKP, has the best tensile characteristics.

These are Technoelas EPP, Technoelast EKP, Technoelast Thermo EPP, Technoelast Thermo EKP, have excellent tensile characteristics, therefore they are used in more critical areas of roofing and waterproofing. Special grades are used in accordance with the manufacturer's recommendations.

Production and application of Technoelast

Technoelast is obtained by double-sided application of a bitumen-polymer binder consisting of bitumen, SBS (styrene-butadiene-styrene) polymer modifier and mineral filler (talc, dolomite, etc.) to fiberglass, fiberglass or polyester. Coarse-grained and fine-grained dressings, polymer films are used as a protective layer.

Technoelast is one of the best Premium materials produced in Russia. Different brands of Technoelast are used:

• for waterproofing the foundations of buildings and structures for various purposes;
• for waterproofing of bridges, tunnels, flyovers, underground structures;
• for waterproofing flat roofs and roofs with a small slope, as well as "breathing" and "green" roofs;
• to protect the foundations of buildings from radon and methane gas;
• for the installation of a roofing carpet in a fireless way;
• for roofing and insulation at facilities where increased heat resistance of materials is required (withstands heating up to 140 degrees);

Laying can be done all year round. Even at very low temperatures, it does not lose its elasticity and strength, it does not stick together and does not "flow" in the heat.

Special grades of Technoelast

TechnoNIKOL produces special-purpose Technoelasts - this is waterproofing, which is designed to solve very specific problems.

• - bitumen-polymer waterproofing material that can withstand heating up to 130 degrees, no other rolled waterproofing material has such heat resistance. Produced on the basis of fiberglass and fiberglass. It is used for waterproofing in hot regions and places with high operating temperatures.
• - self-adhesive baseless bitumen-polymer hydro-vapor barrier material. It is used for waterproofing shallow foundations, waterproofing interiors under a screed, vapor barrier of building structures. Laying by the non-flammable method is possible on objects where it is forbidden to use an open flame, laying on combustible substrates is possible.
• -bitumen-polymer waterproofing material intended for waterproofing the reinforced concrete slab of the carriageway of bridge structures, for the installation of a protective-adhesive layer on the steel orthotropic slab of the superstructures of bridge structures, as well as for waterproofing superstructures with a reinforced concrete slab of the roadway, on which they are laid directly on the waterproofing asphalt concrete pavement, including from cast mixtures with temperatures up to 220 °C.
• - this is a rolled cushioning soundproofing material for soundproofing floors between floors of buildings. The material prevents the spread of impact noise transmitted through the supporting structures of the building.
• - it is a bituminous and polymeric waterproofing material. It is used for waterproofing buildings and structures with gluing on mastic. This technology allows you to combine the advantages of waterproofing from rolled materials (with high physical and mechanical properties) and seamless monolithic mastic waterproofing. It is used for fireless mastic laying.
• - bituminous and polymeric waterproofing material. Possesses increased fire-technical characteristics according to SP 112.13330: flame propagation group RP1 (not spreading flame); flammability group B2 (moderately flammable).
• is a rolled hydro-gas-insulating material. It is used for the device of hydro- and gas insulation of underground parts of buildings and structures. Protects against exposure to radioactive gases, including Radon gas. It is used as an outer (facing to the ground) layer in a two-layer waterproofing.

If you have any questions about Technoelast rolled waterproofing - call and ask our managers, we will try to answer everything.

BUY IN ONE PLACE, SAVE ON SHIPPING, USE DISCOUNTS FOR LOYAL CUSTOMERS