Homemade swings with their own. Do-it-yourself garden swing made of wood: photos and drawings, dimensions and manufacturing recommendations

Holidays with children can be made even more enjoyable by providing interesting elements and facilities.

This is a barbecue area, and a playground or a whole complex.

In this article, we will consider the manufacture and assembly of wooden swings for summer cottages, drawings and photos of various construction options.

Blueprints

There are a lot of advantages in self-manufacturing of the structure:

• the choice of design convenient and functional according to your own taste and desire;
• a product made of natural wood is environmentally friendly and durable (with appropriate processing);
• cost savings (buying a finished product is always higher, moreover, there is not always a guarantee of quality);
• the tree will harmoniously fit into the environment, and the canopy over the structure will allow you to enjoy measured swaying and fresh air without the risk of getting burned under the scorching fire.

Did you know?In Ecuador, in the city of Baños, there is a swing on which brave tourists can soar over a precipice more than 2000 m deep and enjoy the view of the Tungurahua volcano.

We adjust the board to the desired dimensions, place them on a straight surface (on the floor) in the position in which they will be assembled, measure the width of the base and the angle at the top of the future rack.
In the upper part, two racks will be fastened together by a transverse beam. Therefore, the angle is measured, taking into account this detail, the easiest way to take measurements is to cut off excess wood by attaching a short bar of the same width to the parts of the supports folded together, draw a marking line with a pencil.
Cut off excess parts with a jigsaw, assemble all the parts together. Fix with a clamp for complete immobility and make sure that the bottom of the rack is not skewed, a level is useful here, remove excess.
Make the second rack in the same way.

A board of the desired size can be made rounded at the edges protruding from the fastener for aesthetics.

Next, we assemble the support: before screwing in bolts or screws, make sure that all corners of the structure correspond to the calculations.
The rack is not ready yet: it will need additional side rails for reliability. We try on a beam of suitable length to the bottom of the rack, the distance from the floor corresponds to the level of the future hanging bench.
Mark the cut lines with a pencil, making sure that there is no skew with a level. Install the prepared cross member in the right place, fix it with a clamp and fasten it with bolts.
In the same way, fabricate and install the crossbars in the upper corner of the rack about 20 cm below the attachment point. We add fasteners in the upper part for final fixation - the base of the swing is ready.

Important! Remember, all fasteners must be galvanized: this will protect the wood from cracks and extend the life of the wooden product.

Bench

Let's go to the bench. In order not to miss anything when making a swing to the country house with your own hands, refer to the diagrams and drawings.
Make frame parts for the bench of the desired size, turn and sand them, mark and carve grooves in the right places. Don't forget about armrests, they can be made curly.
Then the frame must be assembled and fixed with a clamp (one tool is indispensable here) in order to more accurately calculate the width and length of the back and seat parts. Start making details of a bench for a wooden swing, it is not difficult to make them with your own hands, the main thing is to take measurements accurately.

Two long parts with a groove turned along (for lamellas) and spikes at the ends. A thin planochka, narrowed on one side (under the width of the groove) and equal in width to two bases, will be needed during assembly to close the groove between the lamellas. Cut the plank into pieces equal to the width of the gap between the lamellae.
Further make lamellas, depending on the length of your bench, there will be from 10 to 12 pieces on the back, located perpendicular to the bases, do not forget to carve spikes at both ends for the grooves made in the bases.
For the seat, make the slats longer by the length of the bench, they will be parallel to the longer bases of the seat. The number of slats also corresponds to the width of the seat.
All parts are ready, start assembling the bench.

Assemble the backrest: install one of the bases with the groove up, mark the location of the lamellas with a pencil. Lubricate the groove and install all the slats in turn, and then the chops that close the gaps between them.
Also fix the upper base with glue and fix the assembled back with clamps.
Next, assemble by smearing all the grooves with glue, and fasten the frame for the bench with bolts. Install the prepared back on the frame, coat the spikes included in the grooves of the two side frame guides with glue.
Grind, sand, fix the seat slats with glue and press with a clamp.
Do-it-yourself wooden swing is almost ready, it remains to install the suspension and canopy.

(18 ratings, average: 4,00 out of 5)

Nursery garden swing in the country is a casual game, great leisure and fun. There is always a lot of children's laughter and joy near them. By installing them at their summer cottage, you can get another place for a pleasant pastime. By following the simple rules for creating design and safety, you can make a children's swing for a summer residence with your own hands.

In order to get it right calculate the possibilities and forces, you must first determine the preferences of family members and get acquainted with the manufacturing options (photos and drawings of a garden swing can help with this). Some prefer to lie languidly with a book or tablet, and some need to sway with a whistle in their ears.

Types of homemade swing

Swing garden wooden are divided into several main groups:

• balancing or sofa swing for giving. This type of swing for two;
• hanging swings on chains, cables or ropes, like a "bungee";
• a swing made of logs that are on stationary supports (classic look).

Each model can beat like this that the household will choose her favorite corner of the garden or cottage, and all the neighbors will begin to envy.

Where to install?

When the choice made in favor of the "bungee", then the answer to the question is obvious - we install it on the nearest tree, which inspires confidence in terms of strength. And when choosing a place for other types of swings for giving, it is necessary to take into account such factors:

• illumination. The best thing, so that the sun's rays got to the site until the evening. Thus, a garden swing made of wood will be insured against dampness;
• sufficient distance from fences, walls, wires, trees, pointed objects and thorny bushes;
• the site should not blown by all the winds". Constant drafts are fraught with colds;
• it is advisable to immediately select a smooth surface relief so that there is no need to perform additional work.

Great when under construction soft grass or sand. This will make it possible during the fall not to get injured on the reinforcement or stone.

Gallery: do-it-yourself garden swing (25 photos)

Drawings of a swing for a summer residence

You can do without them. However, when a serious project is meant with a claim for long-term operation, then for reasons of saving building materials, it is advisable to prepare a drawing of a swing . design a wooden swing with your own hands it will not be difficult when there is at least a slight experience of such work.

General provisions that display the drawings of a children's garden wooden swing:

• sizes. That is, the area of ​​the base and the height;
• frame structure;
• type of suspensions and their length;
• number and type of seats;
• it is necessary to note the places of reinforcing elements and fasteners.

Material for manufacturing

Whatever type of swing is chosen, it is necessary draw a lot of attention on the quality of the material (directly on the tree) from which the structure will be built. A high-quality tree can not only ensure the durability of the structure, but, most importantly, guarantee the safety of operation.

The following species showed themselves well: larch, oak and cedar. Also, wooden swings are often made of birch, pine and spruce.

wood must be purchased dry, without foci of decay or traces of mold. There should be no holes made by pests, crevices, falling knots. The construction of a do-it-yourself swing made of wood does not require a large amount, so you can check each beam and board.

Instruments

Before you make a swing in the country with your own hands, you need to make sure that you have all the tools required for this.

You will need:

This basic tools. When everything is prepared (project, drawings and material), we begin to build a garden swing in the country with our own hands.

In this case, the main difficulty is what to hang on. When you have a suitable tree growing, it is advisable to make the crossbar from a log (about 25 cm in diameter and 3 meters long), fixing it with ropes. A strong branch at the required height will relieve the need for this design.. When not in the country find a suitable tree, then, in addition to the supporting beam, two logs (30-40 mm in diameter) will also be needed to assemble the U-shaped frame.

Pre-logs need treat with an antiseptic and sanded, then they are placed in prepared pits (50 cm) with crushed stone at the bottom and filled with cement mortar. When pouring cement is not planned, then the logs will need to be dug to a depth of at least a meter.

During the installation of the frame, the most important thing is to prevent distortion. There is an interesting option to adjust the level correctly: the Egyptian plumb line. D this system is quite is simple: the upper load is a nut or any curved piece of iron, and the lower one is a small container of sand.

As for the seat, there are many variations for every budget and taste:

• from the board (with and without a back, on two suspensions or on one central one);
• from a log (of one thick diameter or 2-3 thin ones, which are connected to each other with fasteners or a rope);
• from a tire (solid or cut, horizontal or vertical arrangement).

To the choice of material for suspension, with which we will hang a bungee on fastening, it is necessary to treat responsibly. Cables, ropes or ropes must be reliable, best of all new, and not rotten from attic stocks. It is not recommended to use chains in this case, as the child can easily pinch his fingers in them.

Suspensions during fastening on a carrier beam must be no closer than 1.5 m from each other. You can secure them with leather-wrapped loops or hooks. You can also use special steel fasteners - thimbles. The most durable fastener is a carabiner with a collar. However, safety teeth must be on the carabiner, otherwise it may move during strong swinging.

Usually , frame swing for summer cottages they have a fixed solid base, for example, a sofa or a bench. This is a more permanent structure, unlike rope structures. Most often, this building is installed not only for children, but also great for relaxing with the whole family. Construction options will depend from selected material.

Log swing

Today swings made of logs are quite relevant. Though they look bulky but reliable and original. The seat can be hung on L-shaped, U-shaped and X- or A-shaped frames.

At the same time, X-shaped frames are the easiest to make: on the logs fixed with a “cross” (about 12-15 cm in diameter and 2.5-2.8 m long), a load-bearing beam is superimposed on top. The cross begins approximately 45-60 cm from the ends of the logs. For fixing, threaded spokes (15 mm) are best suited, which are fixed with nuts on both sides after installation.

The lower ends of the supports are cut inward at an angle of 45 degrees. Then, on each cross, it is necessary to fix the ties in the form of bars of small thickness measuring 2-2.5 m at a level of 35-50 cm from the lower ends.

We install both crosspieces and fasten the third tightening log between them at the same height as the first two, and also fasten the supporting beam in the upper grooves. The frame of the swing is assembled from logs. Now you just need to hang a sofa or put together a bench. The simplest seat can be easily built on a 6x8 cm timber frame, which is then sheathed with a 4 cm thick board. The parameters of the bench-sofa are as follows:

• back height 70 cm;
• bench depth 60 cm;
• length 180 cm.

As suspensions, you can use strong ropes, cables, ropes, chains. They are attached to the bench with carbines or knots. But for fastening to the cross beam, two eye nuts and two large bolts will be needed.

Hanger installation steps:

• In the places where the hangers are fastened in the carrier beam, two holes are made through from top to bottom.
• Bolts are inserted here, eye nuts are screwed in below.
• Carabiners or ropes are inserted into the rings of the eye nuts.

Near a large bench, as a combined option, you can fix a single bungee for children on a long supporting beam.

This is a fairly convenient material for assembly, therefore it is not difficult to build a wooden swing from a bar in the garden with your own hands, however, the skill does not hurt.

To assemble a swing from a bar with your own hands, the following material will be needed:

• for tightening the crosses, one edged board 4x12x70 cm;
• for the crossbar one bar 10x10 cm long 2.7 m;
• for side supports, four bars 12x12 cm, 3.2 m long;
• for a bench: approximately 15 linear meters of a bar measuring 4.6x5.5 cm, for sheathing 20 linear meters of a board 2.5x4.5 cm, as well as fasteners and suspensions.

First of all, we collect the crosses. This is done in the same order as according to the principle for a wooden garden swing made of logs: mark, cut, connect, hang a chair or bench.

On a swing made of timber, the crate of the crosses of their thin rails looks great, where you can attach flower pots. A light roof would also be quite appropriate. A very interesting option is when the roof is made of a "house", as over the wells in the village. If you apply maximum imagination, then this "harbor" in the garden will become a favorite place for family holidays. Especially with soft pads on the bench.

wooden pallet

Probably, many could see latticed wooden coasters for various goods in warehouses and stores. Often, after the importation of goods, they remain in summer cottages. However, the idea to build a garden swing out of it with your own hands can only come to a person with a remarkable imagination. The most important thing is that the pallet is not rotten and strong. It must immediately be treated with water-repellent and antimicrobial compounds, painted and dried.

So, here is another idea on how to make a garden swing for a summer residence with your own hands, and very quickly. A cable, rope, rope or chain is fixed on 4 sides of the pallet and hung on any frame or support. Thus, it is possible to make either a luxurious seat, on which two children can comfortably accommodate and swing together from two sides. Or, by laying a pillow and a mattress on it, we get practically a cradle.

When the farm has two pallets, then by fixing them with corners, you can build a bench that will look great on any frame base.

Balancer or swing scales

Once upon a time, such entertainment for two was a mandatory attribute on playgrounds. Which were willingly ridden not only by children, but also by older romantic people. On the garden plot, these swings will certainly come in handy.

When everything is relatively clear with hanging structures, then how to make a wooden balancing swing with your own hands to give? These swings can be made from boards, bars and logs.

For the simplest classic option, you will need:

• metal or wooden pin;
• a piece of thick saw cut or log;
• two handles;
• two beams measuring 30x30 cm;
• a board not less than 4 cm thick and about 2.5 m long.

So, the construction process is quite simple:

• Lay the log on its side.
• We fasten it on the sides with bars so that it does not roll on the ground.
• Having found the center, we fasten the pin.
• We put a board with fixed handles on the pin.

And now another garden wooden swing is ready.

How to care for a swing made of wood?

• From the end to the beginning of the new season, you need to cover the structures with waterproof material.
• Annual painting or treatment with special compounds will save the swing from pests and decay.
• Do not create disproportionate loads.
• Avoid rust on metal parts.

Garden wooden swing is a great way to relax in the country. It is even more pleasant if they are made by hand. Their construction does not take a lot of time, but you can literally enjoy the result every day!

Remember childhood sensations from the swing? This is not only pleasant, but also useful - monotonous rocking trains the vestibular apparatus, and also calms the nervous system. The second property is very useful in our time. Such a pleasant treatment-relaxation after a busy day. Moreover, any person with “straight” hands can make a swing with their own hands. There are, of course, complex models, but there are much more simple ones.

About designs

Like most outbuildings, swings are most often made of wood. Racks and crossbar - from timber, logs, seats - from planks and even from parts of home furniture.

A little about designs. There are three main types of hanging swings, or as they are also called - boat swings, sofas, benches, etc. The main difference is in the type of support structure: there are A-shaped and U-shaped. You see an example with racks folded into a triangular structure above, and in the photo below an example with a U-shaped rack. This is more likely with a hanging bench and it is built according to the same type, only taking into account swinging loads.

There is a third type - this is already a complex structure that requires certain skills - it is based on articulated joints and they swing from their feet to the floor. We will immediately give both photos and diagrams for those who wish (you can expand it to full screen by clicking on the arrows in the upper right corner of the picture).

We make a swing with our own hands from wood

Most often, they independently make a design in the form of the letter "A". It is simpler, requires less material consumption. We will analyze the nodes, fasteners in more detail, talk about materials, protection against destruction and stability.

materials

Immediately about what to make a wooden swing from. The choice of lumber section depends on the planned load. If it is assumed that one adult will sit, the uprights and the upper crossbar are at a minimum - 50 * 70 mm. If a larger number of "seats" is supposed - two or three, then the cross-section of the beam is at least 100 * 100 mm, better - 100 * 150 mm. It has been experimentally established that such a design, when using a beam of 100 * 100, can normally withstand a total load of about 200 kg. If you need more - take a larger section, or put logs))

About what the bench / sofa is made of. A bar 70 * 40 mm will go to the frame, the back height is at least 600 mm, the seat depth is at least 480 mm. You can experiment with the depth of the seat and the angle of the backrest: there are options for a “lying” position. Accordingly, both the length of the sofa and the dimensions of the structure change greatly from this. For fastening use nails 200 or studs at least 10 mm in diameter.

How to position the racks

Scheme with dimensions and a list of the required material in the photo below. To be frank, few people make from such materials as indicated in the specification. More often they put a bar.

There are varieties of this design: with or without a lower frame. If the swing is installed on a hard platform and the fasteners are made rigid, on studs, without the possibility of backlash, then such a design will stand without problems. If in doubt, you can make a screed from a bar along the bottom, nail it with studs to the coating, or drive the staples into the ground.

A crossbar has been added here, there is nothing to move apart The simplest design, but the “legs” can move apart

For those who are afraid of lateral loads - the design in this axis is not the most reliable - we can offer to install racks with a slope. The area will be large, but the stability will be high.

If installation in the ground is intended, parts of the posts that will be buried must be treated with bio-protection. As a cheap option, put it in a vessel with used oil for several hours. Dry, then bury. They bury to a depth of at least 50 cm, pour a little rubble on the bottom, set up racks and concrete. If you are afraid that this is not enough, attach a few strips of metal crosswise at the bottom. The hole will have to be dug larger, but the holding area will be larger.

Ways of fastening the crossbar

In all swings of this type - with racks sawn at the top with bars - the problem is the attachment point of the crossbar, to which the bench is then hooked. In the photo above, it is solved reliably, although not entirely aesthetically pleasing. The trouble is that aesthetic methods are difficult to perform. And, if you are not for sale, it's faster to do something inelegant, but reliable. So, in order to fix the crossbar, an overhead beam is attached below the intersection, pulled to the uprights with studs. A cross member rests on it, which is held from lateral shifts by racks and fasteners - nails and spikes.

Another way to install the crossmember is to mount the side racks in the form of the letter "X". With this option, the carrier beam fits perfectly. It is additionally fixed with nails, and the racks are pulled together with studs. See the next photo for this.

Everything is fine, but the length of the sofa is not enough ...

By the same principle, a do-it-yourself swing is assembled from logs: the side ones are fastened crosswise, and a support log is laid on top. If the timber is sometimes assembled on nails, then in the case of logs, studs are mainly used.

For those who are familiar with carpentry, there are other options: half a tree. Such a project is in the photo gallery below with close-ups of some of the key nodes.

How the racks are fastened together - inside view

Photo gallery of homemade swings on chains

And a few photos of different swings made on the basis of an A-shaped design.

From thin logs under a reed roof - it looks great Chic option - 3-seater, or maybe more, a swing manufacturing This is a whole swing house .... cool Immediately and a ladder ...

Fastening the swing to the crossbar

The swing mount also requires clarification, that is, it is not obvious to everyone how to hang a bench-sofa on the crossbar. First, the crossbar is drilled from the bottom up through. A bolt is passed through the hole, to which the eye nut is attached. One or two wide washers are placed under the nut head so that it does not squeeze under weight.

It turns out that the eye-nut ring is located at the bottom. You can attach a carabiner to it, throw a rope or cable, etc. Just note that the carabiner should hang normally, freely on the eye-nut ring. And in the carabiner, two links of the chain should fit freely. Therefore, it is advisable to buy everything together in one store: you can try on the entire knot at once.

By the way, in the rigging store you can stumble upon other devices that can be adapted for attaching chains or ropes from the swing seat. For example, such as in the photo below.

They are designed to lift loads from 0.5 tons, so it makes no sense to use them for children, but on a swing for adults - quite.

Such a mount has a significant minus - a creak is heard when swinging. For a while, you can get rid of it by lubricating the knot, but this operation will have to be repeated periodically. The way out is to make a knot on bearings, but you can’t do without welding.

Do-it-yourself metal swing

Their structure is exactly the same. The material is different, and the way it is attached. This is welding. For those who are familiar with, it will not be difficult to cook something similar. And for inspiration, a photo report.

Below is a drawing of this swing with dimensions. Some explanation is required. In the figure there is a pipe welded around the perimeter (this plane is shaded). It is buried and therefore not visible in the photo. It was made in order to increase stability: the masses of friends are considerable. For the same reason, metal plates are welded onto the ends of the racks. The installation was complicated, but the swing is tight.

For manufacturing, it took 22 meters of a profile pipe 50 * 50 mm, for a seat 25 * 25 mm - 10 mm, boards 2000 * 120 * 18 - 7 pcs and the rest - fasteners, paint, anti-rust.

There is another way to attach the swing to the crossbar. He is in the photo.

A way to make a metal swing mount to the crossbar

The original form of a swing from a profile pipe - the racks are non-linear, but curved. If it is possible to do this with a tree, then only the master.

Baby swing

For children, you can make the same design, but smaller.

There are several other models for , but about . Here are the first ones - a swing-scale or a balance beam.

Swing for children - balance beam or scales

Everything is clear, questions may arise only on the attachment point. Below is a drawing with dimensions. To strengthen the upper part, steel plates are fixed inside. To make them swing, a hole is drilled into which the pin is threaded. You can improve the "rolling" by inserting bearings.

You can quickly and easily make a nest swing from a tire (car tire). Bolts with eye nuts are installed in it at four corners, but of a smaller diameter (do not forget about the washers), ropes or chains cling to them, and you can even throw them on the corresponding branch on the tree, even hang them on the horizontal bar.

Today, a large number of people have country houses or summer cottages - places where you can relax and unwind from everyday hustle and bustle. Today we will tell you how to make a metal garden swing with your own hands for your summer cottage.

This material is conditionally divided into 3 parts.

• In the first part: the use of metal to build a swing, and why country builders prefer it. We will talk about the advantages and disadvantages of such structures, calculate the mass of planned attractions, and also talk about the types of attachment for stationary and hanging swings.
• In the second part: we will tell you how to make an outdoor metal swing for a summer residence in the form of a bench or a sofa with your own hands, we will also give recommendations on the installation of single structures. And you will also learn how to make a swing seat from a profile pipe with your own hands, as well as a frame.
• In the third part: a little about decorating and caring for iron swings, as well as features of the choice in the store.

Advantages and disadvantages of a profile pipe

If you understand in detail the advantages of a profile pipe, you get the following list.

• The shape of the pipe is optimized for fast production, which means it is very easy and convenient to work with.
• Very economical material, especially when compared with reinforcing structures.
• The stiffening ribs, which are located on the structure, greatly increase the upper limit of permissible loads.
• The material perfectly resists mechanical damage - it is difficult to deform it with a blow.

However, along with the advantages, the swing from the profile pipe also has its drawbacks:

• Most of the operations that can be done with the pipe do not require sophisticated equipment. Except one - bending. It is very difficult to bend it, and all because of those very stiffeners. For this you need a special machine.
• Carbon steel rusts easily and is easily damaged by moisture. This shortcoming can be eliminated using the galvanizing procedure, but it also greatly increases the price of the final structure.

Calculation of a profile pipe to determine the mass of a swing

When calculating the size of a swing made of metal, it is necessary to calculate its mass. This will help in the future to determine whether a foundation is needed and what loads the swing will withstand.

• When using a square profile pipe with dimensions of 20x20 and a thickness of 1 mm, the weight of one meter of the tube will be ~ 600 g (it all depends on the steel grade).
• A 30x30 pipe with a thickness of 1 mm has a weight of 900 g, respectively.
• A profile pipe 40x40 with a wall thickness of 2 mm per 1 meter of length will weigh ~ 2300 gr.

Using the data provided, it is easy to calculate the approximate mass of both pipes and the frame of a future garden swing from a profile pipe. We can do this in the following way.

For example, the design uses 8.5 meters of a pipe measuring 30x30x1mm and 3 meters of a pipe measuring 50x50x2mm. Calculate the structural weight:

1. 8.5*900=7650 gr (total pipe weight 30x30x1mm);
2. Since the pipe 40x40x2mm weighs 2300 g, the pipe 50x50x2 has a weight, respectively, 2300 + 2300 * 0.25 = 2875 g.
3. 3*2875=8625 gr (total pipe weight 50x50x2mm).

Appointment of a profile pipe for a swing

In order to correctly answer this question, it is necessary to explain what types of pipes are used for which parts of the swing.

1. Round (oval) pipes. Suitable for curved structures (e.g. seats, armrests, arches).
2. Square and rectangular pipes. They have good strength, suitable for parts that are placed on the surface (vertical racks, spacers).
3. Flat pipes - suitable for auxiliary elements (horizontal struts).

Swing attachment types and classification

Before choosing a scheme according to which we will assemble a metal swing with our own hands, we need to decide on the methods of attaching them to the supporting structure.

There are two main types of attachments for hanging swings:

• on eye nuts;
• to nodes.

In the first case, you do the following:

1. Make through holes in a horizontal beam with a drill (~ 5 mm);
2. Insert long bolts with washers, tighten the eye nuts;
3. Attach carabiners and chains or ropes to them.

In the second case, the sequence is:

1. Throw the ropes over the crossbar;
2. Making a sea knot
3. Attach the other ends of the rope to the seat.

Hanging metal swing

Homemade swings for summer cottages made of metal are often quite small in size. These are usually small seats for one person, mostly for children. They do not need a fixed base to hang them in the yard, they only need a tree with thick enough branches or a supporting structure.

Hanging swings are most often hung on a chain or strong ropes - depending on the desire and style. At the same time, you can fix them without damaging the branch itself: wrap the chain or rope with a sliding knot, which will provide a fairly strong grip. The main thing here is to correctly calculate the thickness of the suspension itself.

Chain attachment example.

1. Drill a large through hole along the width of the seat with a thickness of 7-9 mm (along the red line in the picture);
2. Pull the chain through the drilled chain hole;
3. Screw the steel bolts along the edges of the seat in such a way as to fix the chain.

Stationary metal swing

Do-it-yourself stationary garden swing from a profile pipe is a more complex option, but no less popular. Great if you need to install seats for two or three people.

For a stationary swing, in addition to the seat itself, it is necessary to make a frame from a profile pipe. This is the supporting element of the entire structure, the heaviest loads will fall on it, so you need to do it with all the attention. Mounting to a stationary frame has several varieties.

Where to install a metal swing on the site

Before you weld a swing or buy it in a store, you need to choose a place on the site, we recommend that you adhere to the following rules:

1. The swing should be located in an open area near the house. The ideal option is 10-20 meters so that you can watch your children play;
2. There should be no communications above the iron swing (water, power lines and other wires);
3. There should be no roads nearby (it is best to put a fence around).

Having decided on the place, it is necessary to prepare a drawing-project of your design. We recommend that you specify all dimensions in advance - this way you will save a lot of time and resources for revisions and alterations.

Swing in the form of a bench or sofa with a metal frame

This type of swing is common among manufacturers - today on the market you will find a large number of ready-made assembled models of this type. They are distinguished by practicality and relative cheapness. Such swings are suitable for joint gatherings in the evening after a hard day or on weekends with children and loved ones.

Before you buy materials and start making an iron swing yourself, familiarize yourself with the design features:

• this type of metal swing for giving can be both portable and stationary;
• the foundation of a portable structure is not required - the square at the base is the support. In case you decide to make a stationary swing, we recommend that you keep in mind the columnar foundation;
• a canopy is often made to such structures - it can be either a polycarbonate roof or a stretched awning.

Materials and tools

To make a swing from a profile pipe with your own hands, you will need a whole list of tools and materials:

• Round profile pipe for a frame with a diameter of 20 mm, 14170 mm (take a meter or two more with a margin);
• 4 steel corners;
• 2 steel arcs, each 250 mm long and 15 mm in diameter;
• 2 wooden canvases;
• a cable, chain or any other suspension that can withstand a load of up to 250-300 kilograms;
• welding machine;
• pliers;
• hammer;
• vise;
• grinder or hacksaw;
• building level;
• roulette;
• special paint for metal against corrosion;
• eye screws 5x80mm, 4 pieces.
• shackle M5, 6 pieces;
• bolt M6x30, 4 pieces;
• nut M6, 4 pieces;
• spring washer M6, 4 pieces.

Step-by-step instruction

	Cutting parts from profile pipes for iron street swings. For side racks, you will need pieces of 2500 mm, 4 pieces. On the crossbar you will need a piece of pipe, 2100 mm long.
	We cut off the edge of the pipe at 30 degrees at the end, after which we weld them into an isosceles triangle using a welding machine.
	We measure 2000 mm from the top of the uprights and weld a 1035 mm long horizontal bar to strengthen the frame. See the drawing of a garden swing made of metal, which we made for you with our own hands.
	We weld a horizontal crossbar at the ends of the vertical racks. After that, the seat will be attached to it. The distance between the A-posts is 2000 mm, the crossbar protrudes 50 mm on each side.
	Let's create a swing bench from a profile pipe with our own hands. We take several bars 30x30x6000 mm and shorten them. You should get segments of 1500 mm in the amount of 24 pieces. We clean them with sandpaper or a machine tool. Or you can take a bar 100x100 and fit it to the required dimensions. It is not necessary to cut 30x30, you can use 20x50 and 30x70, etc.
	We apply paint and varnish on the surface to prevent rotting of the wood.
	We make a frame from a pipe 15 mm in diameter. We weld the segments together and attach the bars with bolts. The distance between them is 20-25mm. Along the edges, we weld eye nuts for attaching the chain (two on one side, two on the other). You can also experiment with the distance between the bars (it all depends on their size). More details on the drawing of a swing from a profile pipe.
	We fasten the seat to the vertical posts of the metal swing frame. We drill through holes in the crossbar for bolts with eye nuts. We thread them and twist them. We connect the carabiners with all the eye nuts and attach the chain.
	We dig 4 holes with a depth of 450mm. To do this, we use a hand iron drill.
	Mixing concrete. Add cement, sand and water to the container in proportions of 1:2:3. It is best to use cement labeled as M400.
	At the bottom we fall asleep a pillow of sand 100mm, after which we install the racks in the pits. We throw a few large stones for the stability of the structure, after which we fill everything with concrete. We are waiting for 3-4 days until everything dries. The design is ready

Metal single swing

Do-it-yourself single swings from pipes can be welded both stationary and portable - it all depends on who will use them and how much free space you have on the site.

Stationary swings have the greatest stability of all the listed options: children will not be able to turn them over even during the most active game. However, because of this, they have a drawback - low mobility: they cannot be removed during bad weather. Portable, of course, are not as stable, but also much more convenient than stationary ones.

The main stages of installation

	To weld the swing frame from the profile, you need to take the pipe and cut it into two equal parts, each 3100 mm. Cut the edges of the vertical racks at an angle of 45 degrees. After that, it is necessary to form the letter P - weld the third to the ends of these two segments. Its edges should also be cut at an angle of 45 degrees.
	The second step is the formation of a do-it-yourself metal swing structure on bearings. We need two pieces 5 centimeters long from a pipe with a diameter of 90 millimeters. Bearings are inserted into them, after which they are scalded for fixing. On the other hand, for additional fixation, a small piece of metal is welded over the pipe. A piece of pipe with a diameter of 27 millimeters will be inserted into the bearings.
	Two plates are welded to a 27 mm pipe - this will be fasteners for carabiners. The bearing structure itself is fixed on the crossbar with the help of two pieces of metal. They are welded on the sides of the pipe into which they are inserted into the bearings. Important - before starting the assembly of this part, apply grease to the bearing and periodically moisten it with water. If this is not done, then the material will heat up from welding, the steel will expand and the structure will be damaged.
	After the assembly of the frame is over, it is necessary to dig two holes under it, insert the ends of the pipe there and carefully concrete everything. After the concrete has dried, it is necessary to weld stabilizing slopes from the remains of the pipes.
	A frame is welded under the seat of a garden metal swing from a prepared profile pipe. We use a welding machine. At the edges we fasten the eye nuts (marked with green dots).
	We fasten the carabiners to the eye nuts and connect everything with a steel chain.

How to make metal swing seats

Such double swings from a profile pipe can often be found on playgrounds. First, a few words about the advantages and disadvantages.

Advantages:

• strength is the most important advantage of such a swing. Stiffeners greatly increase the bending resistance of the structure;
• profitability - profile pipes are easy to manufacture, which helps to significantly reduce the cost of all materials;
• durability.

Disadvantages:

• careful care - if you do not galvanize the profile pipes and do not cover them with protective compounds, then after a while rust will appear;
• the complexity of bending pipes - this may require additional equipment.

How to weld a frame for a swing made of metal with your own hands to the country house, prepare the foundation and hang the seats, we have repeatedly told, so now we will tell you which seat is suitable for such a design and its dimensions.

The following parts are needed: 3x1600m; 3x880mm; 2x200mm; 5x500mm. More details on the drawing.

A long segment of 1600 mm is installed, 3 short ones of 500 mm each are welded to it - the letter Sh is obtained. Another long segment is welded from the free ends. The back is formed in the same way. Everything is fixed with corners along the edges of each part of the structure and welded together at an angle of 90 degrees. Two pieces of board are attached to the structure with bolts.

To make the back more comfortable for sitting, you need to set it at an angle of 115 degrees. To do this, you need to make an appropriate section at the ends of 880 mm segments for the back.

How to make a garden swing frame - video

To independently create a garden swing frame from a professional pipe, we recommend that you follow the algorithm of actions, as in the video below.

Decorating and caring for metal swings

In order for the swing from the pipes that you made with your own hands to last as long as possible, we recommend that you pre-decorate them and, after every six months or a year, tint them with special paint for metal.

Here's what else you can cover the metal with:

• rust solvent;
• paint-enamel for metal;
• primer for surface treatment;
• paint with the addition of metal powder (yellow).

After the building is completed, you can decorate the structure:

1. Sew seat covers. For them, a dense fabric that is not afraid of contact with moisture is suitable.
2. Paint the side racks with patterns or drawings. To do this, you need a stencil with patterns or figures, paint for metal and a brush (or sponge). Attach the stencil to the walls. Take a sponge and wet it with paint. Blot the stencil and remove it. Repeat the procedure several times.
3. Decorate the area next to a homemade iron swing for the street. Plant flowers, build a small decorative fence, arrange sculptures.

How to choose a metal swing

When buying a metal swing for giving in a store, you should pay attention to:

• size and dimensions. As a rule, the swing has a width of 2-2.5, which is universal and allows you to easily install it on any type of site. If you need unique dimensions, it is best to make to order.
• Manufacturing material. Decide in advance what kind of material you want to see. The classic version is made of metal and wood, but there are also modern materials, such as high-strength plastic, steel bars.
• Price. This is an important factor, since on the market you can find absolutely any model for a different budget.

We offer to consider several models of single and double metal swings, which are now popular on the market:

Model	Price	Manufacturer	Main pros and features
	8 990 rub	China	1.9x1.13x1.8m	up to 300 kg	● double swing; ● soft seat; ● fabric canopy.
	3 710r	Russia	1.37×1.42×1.8m	up to 90 kg	● single swing; ● product bases are installed in concrete; ● wooden seat with chain attachment.
	6 890 rub	Russia	3x1.2m	up to 100 kg	● double swing; ● wooden seat; ● fastening - steel chain; ● without foundation
	12 990 rub	Russia	2.9x1.55x2m	up to 250kg in total	● double swing; ● seat material - plastic; ● suitable for children 3-10 years old; ● production material - steel

In conclusion, I would like to say that regardless of whether you want to assemble a metal swing yourself or purchase a finished product, you need to look first of all at their quality and ease of use, choose only the best. We hope that now you know how to do it. Good luck!

In this article, GD-Home has collected 14 swing photo ideas for summer cottages: from simple to complex, which will not only please, but also decorate the garden. Making a hammock or a swing with your own hands is not so easy without knowledge about the features of structures and fixtures. In order to make your search easier for you, we decided to combine all the necessary information into one BIG REVIEW ARTICLE. Here you will find information about the materials from which they can be made, types of structures and fasteners, as well as drawings with dimensions.

Do not forget to compare the weight of the child / adult with the reliability of the fasteners.

DIY garden swing: what, how and why

Garden swings are usually made from:
- tree
- metal

Wooden structures look more aesthetically pleasing, but have weight restrictions. Mounts should be bought ready-made, plastic products are suitable for children's models, but for adults it is worth getting metal mounts. Decorative forging can be used as a decoration for metal structures.

Idea: To create a swing, materials remaining after repair, such as pallets, boards, etc., are perfect.

Attachment to the support can be done using:
- thick rope
- metal chains with large links

A swing for a summer residence can be:
- portable
- stationary

By the name it is already clear that a portable swing for giving can be placed in a convenient place: on the terrace, in the garden, near the gazebo. They are easy to hide from the rain.

Stationary models have a massive structure and are installed in a specific place. These can be benches without legs with or without a back, models suspended from the ceiling of a terrace or a tree. As a rule, such structures can easily withstand two or three people, unlike portable ones designed for one person.

In order to make a garden swing with your own hands are often used pallets. They need to be sanded with sandpaper, then painted. Sitting on a wooden pallet is quite uncomfortable, so you should take care of soft pillows or a mattress. Products can be decorated with additional decor, in the form of balls, flags, colored ribbons.

Show us a man who would refuse hammock in the country! It can be hung from trees, metal poles or a crossbar. The maximum load is 200 kg.

Do-it-yourself garden swing made of wood: drawings + dimensions

This is the most common design of stationary products. Metal elements will help to stiffen.

1. It is worth installing supports in pre-prepared trenches.
2. After installation, the pits should be concreted. The mortar should consist of sand, cement and gravel in a ratio of 2:1:1, respectively. The amount of water should be calculated depending on the weight of the cement, approximately 40% of its mass.

A phased plan for creating a children's swing

1. The upper bundle is created from the board (115 × 10 × 5)
2. A visor (145 × 23 × 5) is formed to protect metal parts from rain.
3. Prepare two racks (275x23x5). They should be buried at least 60 cm, and then concreted. There should be 105 cm between the posts.
4. A stainless steel chain is attached.
5. Seat is made (60×15×5)

To make such a swing on four supports, you will need screws (1), rivets (5), wooden boards (2), corners for the frame (3), different types of bolts (14, 20), a bolt for fixing the liner (15), the liner itself with internal thread (16), large spacer (17), plain washer (19), deadbolt - 2 pcs (21).

The main (4) and side bars (7) will serve as a support for the entire structure. Metal elements, such as a connecting bar (6) or a kerchief-strut (12), will help to stiffen the product. The awning is fastened with the help of connecting elements (8) to the support frame (18). The seat can be hung on thick ropes (9) using carabiners (10) and a ring (11). Attached to the top bar (13)

To create a bench, you will need boards of the following sizes (cm):

One piece each: No. 11 - 1230 × 90 × 35, No. 12 - 1170 × 90 × 20
Two pieces each: No. 1 - 375 × 90 × 35, No. 2 - 375 × 70 × 35, No. 3 - 375 × 90 × 35, No. 4 - 275 × 45 × 35, No. 5 - 650 × 90 × 35, No. 7 - 585x145x20, No. 8 - 300x45x35, No. 9 - 300x45x35, No. 10 - 1300x90x35
Three pieces each: No. 13 - 1230 × 90 × 20
Four pieces each: No. 6 - 530 × 45 × 35
Twelve pieces each: No. 14 - 850 × 90 × 20

Do-it-yourself swing scheme

Scheme of a children's swing

Number 1 indicates the horizontal element of the side part. You need 4 such elements, 70 cm long with the same width and 5 cm height. The product uses three connecting rods with a diameter of 2.5 cm and a length of 80 cm (2), as well as 4 reinforcing squares measuring 2.5x10x10 (3). The four vertical side pieces (4,11) are 37.5 cm long and the same width and thickness, which are equal to 5 cm. To create the backrest, you will need two side pieces (5) of the same size. The seat and back are made of rods with a diameter of 2.5 cm and a length of 58 cm. 13 rods are needed for such a swing. The side elements of the seat have a size of 67.5x5x5 (7). The model is hung on special pendants (8) with a diameter of 2.5 cm and a length of 10 cm. You will also need a pin (9), with a diameter of 1 cm and a length of 7 cm, and a seat lock (10), with a diameter of 2.5 cm and a length of 68 cm .

Such a swing can be hung from a tree or made into an A-shaped structure that can withstand higher loads. The stand can be made of wood or metal.

Important! Accurate calculations of the angle of connection of the racks will allow you to design reliable fasteners. For fixing, you can use corners and screws.

Swing for a summer residence: types of fasteners

In order to create a good garden swing made of wood with your own hands, you should use carabiners or anchors.

1. Carabiners can have a round or rectangular section, so they are perfect for both cylindrical and square timber.
2. Anchors are the same carabiners only with a through type of fastening.

Models with four legs can have three types of mounting:
- 4 carabiners are attached to the ropes and chains, after which - to the support bars.
- 2 carabiners combine two ropes or chains and are attached at two points on the crossbar
- all ropes are attached to the 1st ring (carbine), which is then hung on a support
Obviously, the first type of fastening provides a uniform load on the entire structure.

We wish you success!

In the section you will find 100 ideas for landscape design, as well as creating furniture and decor with your own hands.