After that, the frame of the walls of the woodcutter is mounted from the timber and the rafters for the roof are stuffed.
Home -> Construction of country houses, cottages, construction of bathhouses - Rif Company -> Useful information
On the summer cottage it is convenient to have a spacious shed for working equipment, various tools and other things needed on the farm. The most economical and practical option is a pallet shed, the construction of which will be absolutely inexpensive.
If old used pallets are used for our construction, you need to pay attention to their condition. With improper use of products, wood could gain excess moisture, unpleasant odors from spoiled products, and become saturated with harmful chemicals used to process vegetables and fruits. The boards could rot and begin to crumble.
Therefore, the pallets must be thoroughly checked for suitability for construction work and sorted. After that, our materials must be cleaned of various contaminants and disassembled into pallets using a nail puller. The finished elements will be used for sheathing the shed, so it is advisable to clean them with a grinder and process them with special tools that improve the durability of wood. After the preparatory phase, consider the following questions on how to build a pallet shed.
All stages of construction do not require special skills and craftsmanship, it is only necessary to strictly follow the sequence of all stages of the process. We begin the construction of a shed from pallets with our own hands from the preparation of the site. To do this, select a suitable area behind the house with a relatively flat surface.
The dimensions of the barn should have dimensions that are multiples of the length and width of the pallets.
The area is cleared and levelled. According to the dimensions of the future structure, formwork is carried out, which is covered with sand and gravel and poured with concrete. After it has completely solidified, you can proceed to the next step.
First of all, we build the floors of the barn at a low height from the ground so that moisture from precipitation does not get into the room. To do this, wooden beams are laid out on our prepared site, on which logs are laid on top.
After the floors are ready, we proceed to the construction of the frame of the structure. First, the corner posts are mounted strictly in a vertical position. They are fixed with the help of transverse bars at the top, bottom and in the middle of the frame. The number of crossbars can be different, the main thing is to get a stable, reliable design. The building provides several connectors for doors and windows.
After that, the frame is sheathed with our prepared pallets, doors are installed, which you can also make yourself or buy used ones at an inexpensive price. When the walls are almost completely ready and you are completely sure of the reliability of the resulting structure, you can begin the construction of the roof.
The roof can be of any shape, be single-pitched or double-pitched. For the construction of a gable roof, the frame of the structure is first made, which in turn can also be sheathed using pallets. For waterproofing, a special protective film is laid on top of the roof, on top of which any roofing material is laid. It can be metal sheets, roofing material or other materials.
In order for the barn to be reliable and durable, not to absorb moisture from precipitation, it is desirable to process all wooden surfaces. You can use special anti-corrosion agents for wood, but the simplest and cheapest way to treat such a surface is the usual painting with waterproof oil paints.
If desired, the walls of the barn can be insulated and sheathed with additional materials. But for the construction of a storage place for tools and other household equipment, you can do without these additional works. Externally, the construction of pallets turns out to be quite aesthetically attractive, in no way inferior to capital buildings using more expensive materials.
This article covered all the main points on the topic of how to make a barn out of pallets with your own hands. For clarity, photo and video materials with examples of such buildings are presented.
pallet shed
Do-it-yourself woodcutter is one of the easiest jobs that any owner can do on their own. It can be attached to an existing outbuilding, or it can be arranged as a separate structure. If you also decorate the woodcutter in the country with your own hands, you will get a structure that organically fits into the overall landscape of the backyard. This is where you will store firewood and wood chips for a fireplace or barbecue.
How to build a firewood shed with your own hands and successfully place it on the territory, you will learn on this page.
If your country house has a stove, and there is a brazier or barbecue on the site, then you definitely need a woodshed - a special room for storing firewood. The size of the woodshed will depend on the amount of wood you need.
The location of the woodcutter on the site should be rational in terms of proximity to the house, while firewood should be easy to take and stack. Therefore, it is not worth building it in the far corner of the garden. You can attach it to the hozblok. If possible, it should be located so that a car with firewood can drive up to it, and accordingly, a platform for unloading firewood should be provided next to it. But if this is not possible, then there should be a short path along which you will bring the firewood brought in, and it should be possible for a wheelbarrow to pass through it.
The best option is to attach a woodcutter to an already existing beautiful building in the garden. If a woodcutter is needed only for a barbecue, it is logical to install it on a barbecue area and style it depending on the design of this area: as a “fairy house”, as a “mini-castle”, as a modern “art object”, etc.
You can even overlay a small wooden woodshed with brick or stone.
As you can see in the photo, woodsheds are traditionally built of wood. But a woodcutter is not a barn. You can, of course, store firewood in a room built like an ordinary shed, or even under a canopy. But by and large, special conditions are needed to store firewood. If you take no more than 3 cubic meters of firewood, then you can build a room for them using traditional technology, with solid walls. But if you have a stove and you immediately purchase a large amount of firewood, then the woodshed needs to be equipped according to all the rules. Then the walls of the woodcutter in the country are made according to a special technology: they must be at intervals - for drying firewood. If the walls are solid or at least one wall is not wooden, but there is a lot of firewood, then they will not dry well even in summer.
1. The firewood shed must be mounted on brick posts or on pipes, under which the foundation is poured to the freezing depth. If the building is small, 4 columns are enough.
2. It is necessary to make a frame from a thick bar about 15 x 20 cm in size, on which a wooden flooring will subsequently be mounted.
3. The timber is treated with fire-retardant impregnation, it must be allowed to dry for at least an hour.
4. The timber is insulated with roofing material.
5. Now the flooring from the boards is mounted directly on the insulated frame.
7. The walls of the woodcutter are made of bars measuring 50 x 50 mm. We fill them on the frame of the walls with an interval of 3 cm between the bars. This is necessary so that the firewood is well ventilated.
8. A shed roof is made from corrugated board.
9. For the doorway, racks made of timber are set to the size of the future door, they are mounted on the floor of the woodshed. A wooden door is being installed.
Before you make a woodshed, consider whether it will be on public display or disguised. Unless your woodcutter is hidden behind a building, it should be neat. You can decorate it a little.
The most natural way is with firewood. It is enough to lay out a decorative woodpile along its wall or make small niches in the wall and lay them with the most beautiful logs.
In addition, just like a garden shed, it can be styled “like a house”. Wood saw cuts can also be attached to the walls, either arbitrarily, or any pattern can be made from them.
It will look great on slatted walls. It will look like the original screen.
We offer you to install a prefabricated metal woodshed in the country.
The prefabricated metal structure of the woodcutter allows you to disassemble and assemble it if necessary, moving in the country.
The woodcutter (woodcutter) is ideal for storing ready-made dry firewood in the country, as well as for drying split firewood in the summer.
The design of our country woodshed allows you to install it next to the wall of the house, garage, utility block, but not close, but so that dampness and mold from firewood do not move to the main building. Between the wall of the house and the woodcutter there is a constructive gap formed by metal braces that reinforce the rear wall of the woodcutter.
The roof of the firewood shed is made of metal tiles, with a slope necessary for the unhindered rolling of snow and precipitation.
The firewood shed has five sections 1 meter wide for convenient arrangement and sorting of firewood (dry, semi-finished, raw; small, large; chopped, not chopped). Our steel firewood storage structure can be installed on blocks, which allows you to use the lower space as well.
You can find out more, as well as buy a prefabricated metal woodshed for giving (including a different size and configuration) by phone:
Order a prefabricated metal woodshed
You can find out more, as well as order a prefabricated metal woodcutter for giving, by phone:
8-921-410-64-00.
How to make a pallet shed
To ensure the most comfortable stay in the country, you will need not only a good house, but also a number of outbuildings. First on their list is the shed, because in any case, you need a place to store things and property that you don’t want to keep in a residential building, such as agricultural equipment, tools or firewood.
Example of a barn with a simple pallet construction
Pretty suitable material to make such a shed are pallets or pallets. If the pallets are cleaned, disassembled and developed a little, you will get quite good and high-quality material for the barn. A shed made of pallets or pallets will not be inferior in strength and durability to other types of buildings, and at the same time it will look no worse than sheds built from other materials, the main thing is to build it correctly, connecting all your imagination to this process.
Such an original barn will be a real find for people who like to build or do something with their own hands with a minimum of financial investment. Pallets are a very affordable material that does not require large cash outlays. The lack of extensive experience in carrying out construction work will not be a problem, since this process does not require any special skills.
The original project of a shed made of pallets covered with plastic panels
It is much easier to build a shed from pallets or pallets with your own hands than many other premises, for this it will be enough only your desire and fairly simple instructions, which you will read below.
First you need to choose the right pallets, which will later be useful to you in order to build a barn in the country with your own hands. In this case, it is better not to use the following categories of pallets:
Usually pallets are made to the same standards and therefore have similar dimensions, most often it is 100 x 120 cm or 80 x 120 cm. There are also pallets of other dimensions.
Before you make such a shed from pallets or pallets with your own hands, you need to carefully consider its design. It will include the shape, dimensions, as well as a place on the site for the future building. For convenience, it is better to choose the dimensions of the shed so that they are a multiple of the dimensions of the pallets.
In this case, you do not have to take additional steps to saw the material, which will facilitate and speed up the construction process.
Particular attention must be paid to the location of the barn, which you are going to build with your own hands. For aesthetic reasons, it is not recommended to build it in the most visible place, but it will also be wrong to place it too far from the house, since you will have to go far for the necessary things. The optimal location of the barn would be a place close to the living quarters, located directly behind the house.
The process of building a shed from pallets
It is necessary to ensure that there are no lowlands in the place where you decide to make a barn with your own hands, as it may be flooded during periods of snowmelt or heavy precipitation.
If the pallets have already been purchased, the barn project is ready, and the place has been chosen, then it's time to prepare the material for construction. This process will include the following pallet work:
Building a barn from dismantled pallets
If you had to face this problem, you can cut the nails with the help of a grinder.
As a result of the work carried out by one's own hands, boards and crossbars were obtained - material for cladding the walls of the future structure, building the ceiling and fasteners.
For the construction of a medium-sized barn, approximately 32 whole pallets will be required.
The sequence of actions when building a barn from pallets or pallets is as follows:
Installing a pallet shed on a columnar foundation
The sequence of layers must be observed exactly like this. The concrete surface can eventually become the final version of the building floor. The period of complete solidification of concrete is 2-3 days with proper care, the formwork can be dismantled in about two weeks.
Fastening pallets to the bottom rail
It is important to place the pallets in such a way that the flooring is in the interior of the building.
Erection of the third row of pallets
In conclusion, I would like to conclude: a pallet shed is quite easy to build on your own, they will save you from having to buy expensive building materials. Knowing this little secret, you can build any outbuildings cheaply and quickly enough.
Do-it-yourself woodcutter is one of the easiest jobs that any owner can do on their own. It can be attached to an existing outbuilding, or it can be arranged as a separate structure. If you also decorate the woodcutter in the country with your own hands, you will get a structure that organically fits into the overall landscape of the backyard. This is where you will store firewood and wood chips for a fireplace or barbecue.
How to build a firewood shed with your own hands and successfully place it on the territory, you will learn on this page.
If your country house has a stove, and there is a brazier or barbecue on the site, then you definitely need a woodshed - a special room for storing firewood. The size of the woodshed will depend on the amount of wood you need.
The location of the woodcutter on the site should be rational in terms of proximity to the house, while firewood should be easy to take and stack. Therefore, it is not worth building it in the far corner of the garden. You can attach it to the hozblok. If possible, it should be located so that a car with firewood can drive up to it, and accordingly, a platform for unloading firewood should be provided next to it. But if this is not possible, then there should be a short path along which you will bring the firewood brought in, and it should be possible for a wheelbarrow to pass through it.
The best option is to attach a woodcutter to an already existing beautiful building in the garden. If a woodcutter is needed only for a barbecue, it is logical to install it on a barbecue area and style it depending on the design of this area: as a “fairy house”, as a “mini-castle”, as a modern “art object”, etc.
You can even overlay a small wooden woodshed with brick or stone.
As you can see in the photo, woodsheds are traditionally built of wood. But a woodcutter is not a barn. You can, of course, store firewood in a room built like an ordinary shed, or even under a canopy. But by and large, special conditions are needed to store firewood. If you take no more than 3 cubic meters of firewood, then you can build a room for them using traditional technology, with solid walls.
But if you have a stove and you immediately purchase a large amount of firewood, then the woodshed needs to be equipped according to all the rules. Then the walls of the woodcutter in the country are made according to a special technology: they must be at intervals - for drying firewood. If the walls are solid or at least one wall is not wooden, but there is a lot of firewood, then they will not dry well even in summer.
1. The firewood shed must be mounted on brick posts or on pipes, under which the foundation is poured to the freezing depth. If the building is small, 4 columns are enough.
2. It is necessary to make a frame from a thick bar about 15 x 20 cm in size, on which a wooden flooring will subsequently be mounted.
3. The timber is treated with fire-retardant impregnation, it must be allowed to dry for at least an hour.
4. The timber is insulated with roofing material.
5. Now the flooring from the boards is mounted directly on the insulated frame.
6. After that, the frame of the walls of the woodshed is mounted from the timber and the rafters for the roof are stuffed.
7. The walls of the woodcutter are made of bars measuring 50 x 50 mm. We fill them on the frame of the walls with an interval of 3 cm between the bars. This is necessary so that the firewood is well ventilated.
8. A shed roof is made from corrugated board.
9. For the doorway, racks made of timber are set to the size of the future door, they are mounted on the floor of the woodshed. A wooden door is being installed.
Before you make a woodshed, consider whether it will be on public display or disguised. Unless your woodcutter is hidden behind a building, it should be neat. You can decorate it a little.
The most natural way is with firewood. It is enough to lay out a decorative woodpile along its wall or make small niches in the wall and lay them with the most beautiful logs.
In addition, just like a garden shed, it can be styled “like a house”. Wood saw cuts can also be attached to the walls, either arbitrarily, or any pattern can be made from them.
It will look great on slatted walls. It will look like the original screen.
A small shed in the country is a necessary object. It can store garden tools, tools, some household items that are not used in winter, and so on, so on, so on. Today, many summer residents use wood heating. So the barn is often used as a storage for firewood. In this article I would like to talk about a woodcutter from pallets, as a kind of barn. Why pallets are so well suited for the construction of small objects, the savings from this construction, as well as the technology for building a woodshed.
Everyone has come across wooden pallets. This is a shipping container that is used as a storage unit. Piece goods are stored on it, stored and transported. In this case, the movement is carried out using special vehicles.
In Russia, pallets are not hospitalized goods. This means that they do not have specific requirements in terms of standard sizes. Therefore, different manufacturers have different products with different sizes. But in Europe, these devices have certain standards. But there is no single GOST, and in each country they approach production differently.
For example, the main type of wooden pallets used in Europe are 800x1200x144 mm. And in Russia they are called euro pallets. There is another variety that comes from Finland. Its dimensions are as follows: 1000x1200x144 mm. Sometimes the height is reduced to 138 mm.
The most important parameter to which special and strict requirements are imposed is the bearing capacity. So it should not be less than 1000 kg.
Today, manufacturers produce pallets for different purposes, hence their small classification:
Two-way or four-way. The first are stands into which loader fork may come in with two sides. Second - with four sides.
Single deck And double deck. In the first case, these are pallets, cargo stand which is located with one side. In the second, with two sides, that is, the pallet itself can be placed on any side.
Disposable And negotiable. Everything is clear here, the first ones are disposed of immediately after one use. The second - exploit many times.
For a barn, it is better to use double-entry, single-layer pallets. They are not inferior in strength to others, but at the same time the price of the product is much lower. But since the task is to build a barn from pallets, they are also pallets, the best option is used fixtures. Usually old coasters are thrown away, many of which are still in good condition. Often this wooden material is obtained free of charge.
So, first of all, you need to understand the terminology. There are two almost identical structures: a woodcutter and a woodcutter. They differ from each other in that the first is a firewood shed built on a foundation, which is a separate building. That is, it should not adjoin the main house on a suburban area. The second is a light structure, almost a canopy that adjoins the house.
There is another similar term - firewood. This is a wood basket. Firewood is carried in it, it is installed inside the house, where firewood is stored for heating the stove, heating and other household needs.
It is clear that raw firewood burns poorly, emits heat poorly, but smokes very well, clogging the stove chimney with soot. That is, there are many negative aspects from the use of such firewood. Therefore, they must be stored in a dry place. But in rural areas, where heating is more often based on the use of solid fuel, this can be said about cooking, and kindling a bath, and even cooking barbecue or barbecue, firewood is produced in large volumes. So, they need space, closed on all sides.
So, the woodcutter has certain requirements:
He must be located in convenient location. To him should be free an approach.
Dimensional sizes are selected based on stored fuel.
The barn must be thought out ventilation system. It is forbidden allow firewood inside the building dampened during their storage.
It is forbidden admit to the logs solar rays. Too much dried wood burns quickly.
It is necessary to ensure that the woodcutter is well fit in in the landscape design of a suburban area.
So, it was determined that the woodshed is just a barn. To build it from pallets means that you first need to decide on the dimensions of the structure, and then calculate how many pallets will be required in construction. Let's make a reservation right away that the pallets will be installed, as they say, "on the butt", that is, on the butt. In this case, the end is selected the one in which the ends of the beams used as the base of the pallet will be visible. That is, the bars will be located vertically.
This means that the width of the pallet in the woodshed becomes its height. And if, for example, a pallet with a width of 1 m is purchased, then at least two pallets installed on top of each other are required to achieve an acceptable height of the barn being built. That is, the height of the structure in this case will be equal to 2 m. And the length of the wooden fixture automatically becomes part of the length of the object being built.
For example, the simplest design of a woodcutter is pallets folded in pairs, which are also installed one on top of the other. The number of pairs will depend on the size of the structure itself, given that the length of the pallet for almost all varieties is standard - 1.2 m. As an example, a small barn can be given: three pairs of pallets are long, two pairs are wide. In size, this will turn out to be 3.6 and 2.4 m, respectively. The area of the internal space will be almost 9 m². And taking into account the height of 2 m, this will be a rather serious volume - 18 m³. This amount of firewood is enough for the whole winter for a family of several people.
Now we turn to the technology of building a shed from pallets. And immediately make a reservation that there is no standard technology. But the only thing that unites many varieties is the frame structure of the building. Therefore, first of all, a frame is built, and pallets are already attached to it.
Our website contains the most popular manufacturers of houses presented at the exhibition, which offer services:. You can directly communicate with representatives by visiting the exhibition of houses "Low-Rise Country".
The simplest version of the frame structure is the installation of vertical pillars. For this, beams with a section of 100x100 mm are usually used. They are dug into prepared wells, having previously carried out waterproofing measures. The last is the coating of the edges of the bars, which will be recessed into the ground, with bituminous mastic. For reinforcement, it is often carried out wrapping with roofing material in two layers.
The support posts of the frame are set strictly vertically. Taking into account the height of the barn and the length of the end buried in the ground, the length of the columns to be dug in is calculated. Usually the size of the dug-in end is at least half a meter.
After the racks are prepared, it remains to mount the pallets. For example, this can be done as shown in the photo below. Pallets are put on racks, and fastened to them with long self-tapping screws.
The described installation method is considered one of the most reliable. That is, a barn assembled using frame technology is a strong, stable and reliable structure. But there are other options that are no less reliable. Only they are not assembled using frame technology. Here, reliable fasteners are used, with the help of which the pallets are interconnected into one solid wall.
To do this, pallets joined in one horizontal row are interconnected by long M12 bolts. Therefore, in the bars, which are the supporting base for the pallet, through holes with a diameter of 14 mm are made. It is necessary to make the holes so that when docking the pallets, they coincide with each other. And since there are three pairs of support bars in each pallet, there will be three strong connections that guarantee the reliability of the structure being erected.
The connection can be made with direct hangers, which are used in the construction of false ceilings or ventilated facades.
The video just shows such an option for building a barn, where pallets and direct suspensions are used:
Another option. It is connected with metal pipes. This is somewhat reminiscent of a frame structure, but the approach to fastening is completely different. To do this, at the docking point of the pallets, pipes with a diameter of 32 or 40 mm are driven into the ground. A pair of plates are pre-welded to them by electric welding, in which holes for fasteners are preliminarily made. That is, two pallets in one horizontal row are fastened through the plates with self-tapping screws to one pipe support.
Let's start with the front door. Racks are specially installed for it. Usually these are wooden beams that are dug into the ground or attached to the base in any possible way. In this case, the racks are obligated with a horizontal jumper.
Now, as for the roof. Usually for a small structure it is shed. The woodcutter is no exception in this regard. The main thing here is to accurately observe the angle of inclination of the roof. It can be done by installing a wooden truss on the front side of a small barn. In fact, this is a rectangular structure assembled from bars of a small section. It is installed on the front side of the erected structure and attached to pallets in various ways, for example, with long nails or self-tapping screws.
After that, the rafter legs are laid, the crate is on them, and the roofing material is on top. After that, the farm is covered with sheet material: plywood, OSB boards, corrugated board, sheet iron, and so on.
So, the woodshed is built. But before the start of its operation, there is time, because the erected structure is a sieve. This means that it must be sheathed on the outside with sheet or slab material. There are a lot of options here, the main thing is to accurately fit the constructed object into the landscape design of the suburban area. Usually, decorative design is selected according to the external design of the main house.
A very important point is the base of the woodcutter. It must not only be durable, it must be dry. Therefore, most often a concrete floor is poured into the barn, in addition, it must be higher than the ground on which the barn is being built. This is for rain and snow. Water must not enter the building.
Often the floor is built from the pallets themselves. But in any case, under them form a solid foundation. Sometimes the barn is installed on a columnar foundation. Then, for this, a wooden strapping of beams with a section of 100x100 mm is assembled along the pillars. And already the pallets themselves are laid and fixed on them. The photo below shows just such a barn.
The roof must be erected with overhangs 30-40 cm long. This is a time-tested protection against natural precipitation. As for the roofing material, there are no restrictions. But more often they use slate or corrugated board, less often bituminous tiles, under which it is necessary to lay a continuous crate. And this is an additional cost.
The video shows how a simple firewood shed is built from wooden pallets:
Probably, we must pay tribute to our compatriots, who sometimes build service facilities in summer cottages out of garbage. And in this regard, wooden pallets are no exception. Even unsuitable ones, which are usually used as firewood, suddenly turn into a good building material. The main thing is to turn on the fantasy.
Pallets are such a material that can easily be used in construction. Of these, country houses are most often built and, for which strength is not a priority. Having at your disposal a couple of dozen pallets, a few hours, imagination and desire, you can build a house with your own hands, which will become a favorite place for summer holidays.
Finished pallet house project
Pallets can be hazardous to health, so before using pallets in construction, you should definitely ask about the history of their origin.
The following pallet options are not suitable for construction:
Therefore, the first rule for choosing pallets is an environmentally friendly material without visible defects and damage to the integrity of the wood.
The second rule for a successful choice of pallets is proven suppliers. You can order pallets in any transport company that is engaged in cargo transportation. Here the information you need will be provided and the pallets will be picked up better and cleaner.
Any buildings in which pallets are involved are divided into two large groups: residential and non-residential premises. The first type includes country houses, outbuildings and campsites intended for short-term or seasonal residence of people. Non-residential premises are nothing more than sheds for inventory, as well as front gardens and flower beds.
Consider several options for building premises from pallets with your own hands.
In order to build a whole house, even the smallest dimensions, you will need a considerable number of pallets. But it is the cheapness of pallets that encourages construction.
When the pallet is in your hands, it needs to be divided into two parts: thicker base boards will be useful for the frame of the house, and the crossbars will serve as walls. This procedure is the most boring and rather tedious in the entire construction process.
To reduce the cost of construction even more, you need to responsibly treat the stage of parsing pallets, using a nail puller, not to violate the integrity of the wood. These nails can be reused, which will save money. Next, we take measurements and outline the contours of the future house on a previously prepared plot of land.
He does not need a foundation as such, so it is enough to lay stone blocks on which the frame boards will be installed.
All work is carried out in the following sequence: first, the base is laid out and fixed, after which parallel logs are installed, on which a chipboard sheet is lined.
Read also
Construction of a private house in autumn
After that, vertical supports are installed that form windows and doors. The roof completes the construction process, which is also made of boards. Having installed all the supports and the frame, it's time to take care of the skin. Boards from pallets with the help of nails or wood screws are baited on the logs, controlling the level of their position relative to the axes of the guides.
The roof is additionally covered with a layer of roofing material, making the top layer of tiles. This will protect the house from moisture and precipitation, which is especially important for wood. When the pallet house is completely ready, you definitely need to paint it as well. The paint will protect the house from premature decay, as well as damage by small insects.
Such a house can only be inhabited during the warm season, although in most parts of the United States, it is these houses that are built by average Americans. For our conditions, such a house can be considered a suburban or country house, the role of which is a short-term shelter and protection from precipitation.
Even for such a small structure, a project is required, on the correctness of which the result of all work will completely depend. You can order a project from specialists if your own descriptive abilities leave much to be desired.
Pallets can be given a second life as a play area for children. All it takes is imagination and desire. Typically, playhouses are a hut on a hill, to which all kinds of stairs and other swings-carousels go.
Therefore, in order to build a house of pallets for the joy of children, you need to follow four rules:
Consider the most primitive version of building a children's playhouse with your own hands. We make a foundation. We take four beams and dig them into the ground, to a depth of at least 80 cm. It is desirable that the shape of the house be square. We fasten all the supporting pillars with crossbars, on which we will further line the boards that serve as the floor.
If you have a cottage, then the first thing you will need is the construction of such an object as a barn. Otherwise, where will you store inventory, tools and building materials at first?
If you want to build a barn with your own hands quickly, on budget and with a minimum of effort, look at materials such as used wooden pallets, which can be bought for a penny. In general, what is not made from old wooden pallets: furniture, houses and various outbuildings, etc.
Since the shed is lightweight, it does not need a major foundation. In this case, the foundation is done like this. We dig holes and insert reinforcement into them. Create a rectangular section by stacking blocks.
At the corner of the pallet, we fasten the embedded part with the exit of its bent end beyond the base of the pallet. It will be inserted into the recess formed by the pit.
Fill the pits with concrete. After the concrete has hardened, we remove the blocks.
We set the pallets according to the level. fastening them together.
We set the level of the first row of pallets, fastening them together.
The second tier of pallets is placed on top of the first. Between themselves, the pallets are fastened with bolted joints.
Racks and crossbars are attached to the pallets from above. Rafters are installed on the crossbars at an angle. On the rafters we lay the boards of the crate, on which the slate or profiled sheet is laid.
We sheathe the walls of the barn with siding or profiled sheet.
We install a gate in a niche.
Preparation for the construction of the barn consists of the following activities:
Let's deal with the supporting structure. The barn does not need a massive foundation. It can be installed on small concrete blocks, using them in the corners and in the middle of the walls. However, in areas with high wind loads, it is better to use screw anchors. This is a version of the screw pile in miniature. It is enough to install them at a distance of two meters from each other, the total need for such parts will be 8 pieces.
If you use the frame device scheme, you can make a solid barn with your own hands
The site for this building is prepared as follows:
Thus, the likelihood of stagnation of water under the barn, which will easily leave through the drainage, is reduced.
The amount of materials needed to build a barn is conveniently calculated in tabular form.
Name | Purpose | Quantity (pcs) | Size (cm) | Normative data (pcs/m3) | Notes |
Anchor | support structure | 6 | |||
Pine beam 100x100 Total by type of material: |
Bottom strap length Bottom strap width Top harness by lenght Top strap width Rack rear Rack rear Rack front Doorway |
2 2 2 2 4 1 5 1 11 |
600 400 600 400 200 200 300 90s 200 600 |
16,6 | From segments From the segment Total requirement 0.7 cubic meters |
Beam 100x50 Total by type of material: |
Additional crate in the openings jib Window openings 60x20 cm |
24 8 2 2 11 |
150 300 160 600 |
33 | Total requirement 0.33 cubic meters |
The board is not edged Total by type of material: |
Sheathing outer overlap of the rear wall The same for the front wall Same for side walls |
48 48 32 56 |
200 300 300 600 |
28 | Total requirement 2.0 cubic meters |
Beam 50x150 mm | Translations | 7 | 400 | 22 | Remaining 7 pieces x200 mm Total requirement 0.33 cubic meters |
In addition to the above, you will need a plastic film for a moisture protection device. With a width of three meters, it needs 20 linear meters for the outer protective layer and the same for the inner one. Depending on the price indicators, it can be replaced with roofing material.
The final covering of the roof is taken from the simplest of financial considerations. Suitable ordinary slate or fiberglass, galvanized or painted corrugated board. When calculating the need, it is necessary to take into account overhangs with a width of 0.3–0.5 meters.
Interior decoration is best made from sheet material. Useful and leftovers from the decoration of the house.
Thermal insulation in an unheated barn room has the opposite meaning. In hot weather, it is important to keep the temperature from overheating in the sun. In such a situation, without thermal insulation, it will be very uncomfortable to be in it. It is important to perform high-quality waterproofing of the walls.
A frame shed can also be built on poles
For such a simple structure, the need for a tool is small.
To build a barn, you need to perform a series of sequential steps:
A strong foundation is not needed to build a barn. Often it is installed simply on brick stands. It directly depends on the nature of the soil at the location. If the subsoil layer consists of clay or heavy loam, this threatens with significant soil movements, as a result of which the structure can be skewed with damage to the walls and jamming of the doors. In such a situation, a rather deep foundation is needed, the supporting part of which will be below the freezing level of the soil.
These conditions are met by the following types of support bases:
It makes no sense to consider other foundation designs. They are heavier and more expensive in execution: tape, grillage and other types of support bases, and they are inappropriate for a building weighing several hundred kilograms.
The columnar foundation with a concrete grillage serves as a reliable support Lightweight foundation on piles will withstand loads on unfavorable soils Pile-screw foundation with a wooden grillage for the installation of a barn does not require excavation Strip foundation - a lightweight option for installing a light structure
The base for the barn is ready for further installation when the timber trim is installed and fixed on top of the supports. It should represent a regular rectangle, the diagonals of which are equal to each other. The check is made by measuring with a long tape measure or cord.
Frame assembly:
As an option, you can consider the manufacture of a barn frame from a profile pipe measuring 60x60x3 mm. The dimensions of the building are the same, the distance from the base of the lower harness to the top should be two meters.
The profile pipe for the frame will ensure long-term operation of the barn
The work is carried out in the following order:
Further work on a wooden or steel frame is carried out in almost the same way:
Unedged boards are perfect for finishing the walls of the barn
For the ceiling in the barn, it is better to use sheet material
The draft floor in the barn is made of boards
Thermal insulation of the floor is made with expanded clay. It is advisable to use a fraction of 5-10 millimeters. For wall insulation, it is better to take rolled or slab materials, using the remains of building a house.
The volume of this bulk material is determined by the area of the backfill and the thickness of the layer. The floor area is: 6 x 4 = 24 square meters, the backfill layer, taking into account the layer thickness of 0.1 meters, will be 24 x 0.1 = 2.4 cubic meters. For the ceiling, you will need the following amount: 24 x 1.16 = 28 meters, 2, 4 + 2.8 = 5.2 cubes. Coefficient 1.16 takes into account the angle of inclination of the side walls.
The need for this material is determined by the area of the walls:
Thus, the total area of \u200b\u200binsulation for wall covering will be: 12 + 20 + 18 \u003d 50 square meters.
Sheathing shed walls with plank is inexpensive and lasts a long time Glass wool reliably keeps the temperature in the shed Laying OSB boards on the floor is a practical option for the shed Material with low thermal conductivity will protect the shed from overheating in summer Plywood is an excellent material for finishing the ceiling in the shed
All wooden parts must be treated with fire impregnation and antiseptic. Otherwise, the barn will not live long.
Shed from pallets in the country: photos of construction, interesting videos about the construction of sheds from pallets.
What can be done from pallets? Craftsmen never cease to amaze with their ingenuity, which is not only made from wooden pallets: sofas, beds, tables, benches, patios, flower beds, but this time we will consider a more substantial homemade product - a barn made of pallets.
You may immediately have a question - why build from old wooden pallets, because the pallets themselves are not intended for construction, and all this will look flimsy. But if you need a simple shed for household needs, storage of inventory, old things or just firewood, then in fact a capital building is not necessary, you can build a simple shed almost from garbage and the cost of building a shed from pallets will be cheap.
You can pick up pallets for free at construction sites where they are simply thrown away, but still you have to buy something for construction - self-tapping screws, bolts, nuts, canopies on doors, boards, roofing material.
Let's start building a barn, and first of all we will calculate the dimensions of the future structure. A standard wooden pallet has a length of 1200 mm and a width of 800 mm, it must be taken into account that each pallet of the bottom row must stand on support blocks, so concrete supports must be cast at the junction of the pallets.
Lay out the bottom row of pallets.
The pallets are fastened together with bolts, we drill holes in the transverse boards and tighten the pallets with bolts.
There are several types of pallets, the mounting option will depend on the type of pallet construction.
In the same way, we mount the second row of pallets, but we also fasten them with the bottom row.
We install rafters for a shed roof, observe the slope.
From the boards we will make a crate for the roof.
Now you need to cover the roof, you can use any roofing material, in our case profile sheets are used.
We cover the outside of the shed.
We will make a gate for the barn, we fix the gate on the door canopies.
And once again we paint our building.
Our shed is ready, of course, this is a simple structure and it cannot be called capital, but this is not required for a shed, such a building can be used for household needs, for example, to lay down garden tools, tools or building materials.
And another video about building a cafe from pallets.
In private households, outbuildings are always needed. Store numerous tools, garden tools, building materials and old but necessary things conveniently in the shed. This building is often used as a workshop or as a home for pets. In order for the barn to retain heat and a stable internal atmosphere, it is necessary to build it from a suitable material. For this outbuilding it is better to use foam blocks.
Foam blocks have all the qualities necessary for the construction of low structures and have significant advantages:
The disadvantages of foam blocks include the following criteria:
At the preparatory stage of building a barn from foam blocks, it is necessary to choose a place for its construction. An important point is its convenient location on the site of home ownership. As a rule, two entrances are made in the barn, one of which should be wide and unobstructed. This is convenient when moving furniture and large items, for example, when repairing a house. Depending on the functional purpose, the barn is placed close to the residential building or built away from prying eyes. It is necessary to pay special attention to the layout of the barn, the overall dimensions and its functional premises. With good design, in the future there will be no need to build additional extensions to it. The most convenient for household needs, it has dimensions of 6x3 m (divided into two rooms 2x3 m and 4x3 m). Such a project of an outbuilding will make it possible to use it for different purposes. This barn layout will accommodate not only a workshop, but also a home for pets.
The presence of two functional areas of the barn create convenience when using it
Optimal building dimensions
The truss system of the gable roof forms a floor that is conveniently equipped for storing fruits or grains. The height of the roof is selected depending on the purpose of use. If necessary, you can build a truss system with roof slopes that will allow the arrangement of the second floor. In our case, a roof with a slope of 53º was used.
The dependence of the useful area of the attic on the angle of the roof
You can calculate the number of foam blocks needed to build a barn without involving estimators. By simple mathematical calculations, you can get accurate information about the amount of material required. To do this, you need to know the parameters of the foam block used, the height and perimeter of the future barn. In our case, the barn will be built from foam blocks measuring 200x300x600 mm. With a building length of 6 m, a height of 2.5 m, it is necessary (6 + 3) 2 \u003d 18 / 0.6 \u003d 30 pieces of foam blocks, where 18 is the perimeter of the barn, and 0.6 is the length of one foam block. As a result, one row will contain 30 blocks. Now you need to find out how many strips of masonry are required. To do this, we divide the height of the building by the height of the block 2.5 0.30 = 8.3 rows. In total, 8.3 lanes are required to build a barn, 30 foam blocks in each row. To calculate how many blocks will go in total, you need 8.3 30 \u003d 249 foam blocks.
In some cases, a different masonry method is used, in which the height of the block will be 20 cm and the width 30 cm. In this case, not 8.3 strips, but 12.5 are needed to build the walls of the barn. This value is obtained as follows: 2.5:0.20=12.5, where 2.5 is the height of the wall, 0.20 is the height of the block. Therefore, the total number of foam blocks for laying walls in this way will be 12.5 30 = 375 foam blocks.
When calculating the number of foam blocks, it is necessary to take into account door and window openings. To do this, subtract as many blocks from the total as many windows and doors will occupy. The calculation is done by masonry with a block height of 30 cm. According to our drawing, the barn has two identical windows with dimensions of 50x50 cm and a pair of doors (one of them is double), with dimensions of 0.6x2.0 m and 1.2x2.0 m. For one window opening will need (0.5 2): 0.6 = 1.6 blocks in length and (0.5 2): 0.3 = 3.3 blocks in height.
Since we have two windows, we add the resulting dimensions of the length and height of the blocks 1.6 + 3.3 = 4.9 blocks. Now we know how much to subtract from the total number of foam blocks in order to accommodate two windows. It is necessary to round the number 4.9 to 5 foam blocks.
In the same way, the calculation of foam blocks for doors is done. To open one (smaller) door, you need 0.6:0.6=1 foam block in length and 2.0:0.3=6.66 or 2.0:0.2=10 in height. The second (double door) requires 1.2:0.6=2 foam blocks in length and 2.0:0.3=6.66 or 2.0:0.2=10 in height.
Total 1 6.66 = 6.66 and 1 10 = 10 blocks, as well as 2 6.66 = 13.32 and 2 10 = 20 foam blocks, 6.66 + 10 + 13.32 + 20 = 49 .98 blocks, rounded up to 50 foam blocks.
Then you need to calculate how many blocks will occupy the openings of doors and windows. For this 50+5=55 blocks. Now you need to subtract the extra ones from the total number of all blocks. For this, 249–55 = 194 foam blocks are needed to build a barn with doors and windows.
Now you need to determine the amount of material for the roof. This requires wooden beams and boards for the gable roof truss system, as well as roofing material. As this material, a red metal tile will be used.
The length of the front, rear and side overhangs should be 50 cm longer than the width and length of the base. This is necessary to avoid getting snow and moisture on the walls of the barn. To build a gable roof you will need:
Depending on the material from which the barn will be built, the type of foundation is selected. For this building, the following types of foundations are used:
An important point will be the study of the characteristics of the soil, since they may cause certain problems in construction:
Visual determination of the quality of layers
A barn made of foam blocks tends to keep a constant temperature indoors well, but it still needs additional work on insulation. This will eliminate the possibility of freezing of the walls and the destruction of foam blocks. In cases of low temperatures for a long time, it makes sense to insulate not only external, but also internal walls, floors and the ceiling of the barn. To date, there are several ways to insulate walls:
Warming the outer walls of the shed with mineral wool is a relatively inexpensive method with good thermal insulation properties. Due to its vapor permeability, this material perfectly ventilates not only the blocks, but also the interior of the barn. Mineral wool is resistant to fire and durable in use.
There are disadvantages of using mineral wool:
Mineral wool - one of the ways to insulate walls
Insulation of external walls with polystyrene foam or polystyrene foam is very convenient during installation. Quite often, these materials are called one foam. In fact, these materials have a common basis, but differ significantly in their characteristics.
Unlike mineral wool, this material is cheaper, has excellent frost resistance and is able to isolate sounds well. As a thermal insulation, the performance of expanded polystyrene is significantly higher than that of mineral wool.
Reliable and cheaper way - insulation with polystyrene foam
Thermal insulation of internal walls with cork has several advantages:
For insulation with cork material, it is not necessary to smoothly plaster the walls.
The material is easy to install
The heat-insulating layer of foamed foil polyethylene (penofol) allows you to save heat in the room by 97%. This material is used to insulate the interior walls of the barn. When it is mounted on a wall of foam blocks, bars of small section (10x10 mm) are attached. Penofol plates are laid between the bars. Joints are sealed with aluminum tape.
The material is water repellent
Insulation with polyurethane foam is used both for roofing, exterior walls, and for interior decoration. The technology of applying polyurethane foam by spraying greatly facilitates the work of insulating the walls of the barn. Due to this property, there is no need to use adhesive solutions. Sprayed polyurethane foam is firmly attached to the wall surface and hardens immediately. This material has found its wide application due to its advantages:
If we compare the thermal insulation properties of polyurethane foam with other popular materials, then its 50 mm layer has similar qualities as an 80 mm foam layer or 150 mm mineral wool. With its fire resistance, polyurethane foam surpasses all previously mentioned materials. It ignites only in close contact with an open flame, and ignition of the material does not occur.
The material is quickly applied to the surface
Warming the floor of the barn with expanded clay gives a good thermal insulation layer. To use this material, a concrete floor is required, on which a crate of wooden beams with a section of 15x10 cm is installed in increments of 40 to 60 cm. It should be noted that the expanded clay layer should not be less than 10 cm, since the smaller thickness of the coating with this material loses its thermal insulation properties . Granular expanded clay is poured between the bars of the crate. Then the expanded clay granules are leveled so that it does not rise above the wooden structure of the crate. A vapor barrier layer is spread on top, which is covered with a subfloor made of plywood or OSB boards.
This material protects floors
To build a barn from foam blocks you will need:
When all the tools are ready, and the necessary materials are purchased, you can proceed to the direct construction. For a barn of foam blocks, a strip foundation was chosen. To install it you need:
It is more convenient to do this with a cord
It is desirable to do the depth below the freezing point
Compacted wet sand covered with gravel
Reinforcing cage firmly fastens the wire
The monolithic structure of the foundation will become a reliable support for the building
Reinforcement will betray the walls of additional strength
A layer of waterproofing will protect the wood and blocks from destruction
Cord required for precise mounting
Metal fastenings will create additional rigidity
The light weight of this material does not create a significant load on the truss system.
Aluminum plank will strengthen the foam boards
In order for the wall to “breathe”, it is necessary to leave gaps in the glue
The expansion on the dowel will additionally fix the plate to the wall
Its application will level the surface of the wall for a finish coat.
With painted walls and metal tiles, the barn looks more attractive
kayabaparts.ru - Entrance hall, kitchen, living room. Garden. Chairs. Bedroom