Mousetrap from a plastic bottle with oil. We make a mousetrap from a plastic bottle with our own hands

For thousands of years, mankind has come up with something to fight rodents. To destroy them, it threw the achievements of mechanics and the chemical industry, electricity and ultrasound - perhaps not atomic technology. But the simplest means can be recognized as the most reliable, for example, a mousetrap from a plastic bottle.

Despite the simplicity of bottle mousetraps, they are still very effective.

Unique simplicity

If rodents were not so cunning and inventive, a person would not need to invent new ways to deal with them. There are a lot of funds, but ultra-modern factory devices are not cheap, and their effectiveness is at least debatable. At the same time, it is easy to make a mousetrap from a plastic bottle with your own hands. It will work no worse than fashionable branded features.

Here is one of the simplest options:

This video shows how to create a mouse trap out of a bottle:

Such a trap for mice from a plastic bottle can be made in just a few minutes. Do not use glue to fasten components: its smell can scare away rodents. You can do without an awl: just glow the wire and pierce the plastic.

Engineering solution

You can build an even simpler mousetrap from a bottle with your own hands by cutting off the lower part of the container, making cloves from the walls and bending them inward (a tin can is also suitable). There are also more complex solutions. This is not only a dacha-village option, it is quite suitable for a city apartment.

It is done and applied like this:

Homemade mousetraps from a plastic bottle are also good for their economy - the materials for them are always available, you don’t have to spend money on them. In addition, the animals remain alive, they can then be released into the wild away from home. It would be useful to wear rubber gloves at the same time: mice are carriers of various infections.

Safety for everyone

In a discussion about why and how to make a mousetrap from a plastic bottle, one should not forget about its advantages. Such products, unlike spring-mechanical devices and chemicals, are safe for people and pets. Traps can be made without even using cutting tools. But this will take a little more time.

You can make and use such a safe homemade product:

The trap should be checked from time to time, as the rodent can die from starvation and weather conditions.

It is not enough to know how to make a mouse trap out of a bottle. It will be useful to follow some rules. So, if this device is not installed at home, but in the country, it is advisable to check it from time to time. After all, when the rodent dies of thirst and hunger, the unpleasant smell will intensify every day., and this is undesirable and based on sanitation considerations.

Some tricks and features

Simple mousetraps can be made in other ways. The role of the most elementary of them can be performed by a glass jar (or a bottle with a wide mouth) with a bait at the bottom. You can use a bucket or other container, on top of which a strong wire is placed, and on it - a ruler with food at the end. In catching rodents, no tricks will be superfluous.

Of the other methods, as well as features, at least the following can be noted:

1. A captured rodent can be released, but this must be done away from home, otherwise the pest will most likely return.
2. If it is decided to fight rodents “to death”, then when using a system with a bucket, it is worth pouring water into it. So that the pest is not saved, you should not fill the bucket completely.
3. The wire rack above the bucket can be made to rotate. So the trap will become reusable.
4. The neck of the jar can be sealed with paper cut crosswise: this will make it more difficult for the rodent to escape.
5. A jar, a box of cake can be used even in combination with an elementary support (twig, coin). The animal, making its way to food, will disturb the balance of the structure and will be trapped. For a greater guarantee, the bait can be fastened to the wall of the box.
6. You can catch a rodent using a champagne bottle with a small amount of oil poured into it.
7. For rodents, the smell of food is important. Therefore, fried seeds, salted or smoked lard, cheese, bread, nuts, meat, sausage are well suited as bait. Rice, wheat, buckwheat are also used.

In order not to bring the situation to the point of thinking how to make a mousetrap out of a bottle or use other means of rodent control, it is good to take preventive measures. They consist in observing sanitary rules, maintaining cleanliness. Food should be stored in inaccessible places, and holes and cracks in partitions, foundations, and floors should be eliminated.

Cunning mice successfully bypass human traps for centuries. It can be said that rodents acquire the experience necessary for survival, although sometimes the simplest means are enough against them. The name of one of them (and probably the most ancient) is a cat.

Rodents can settle in a room where from time to time there is access to products. The consequences of such a neighborhood are disappointing. In addition to irritation and anxiety, mice are carriers of infections, active pests for products and furniture in the house. The solution to the problem can be a do-it-yourself mousetrap made from improvised means. Below is a rating of the most effective trap options that you can make yourself.

What are the advantages of mousetraps made from improvised materials?

Before looking at the features of the top mousetraps, a few remarks about their advantages over ready-made traps or fancy devices such as electronic mousetraps for exterminating rodents.

If we compare home-made traps with drugs used to bait rodents, then the former will be more humane and safer. You can catch uninvited guests with homemade boxes, buckets and bottles at any time without requiring the removal of household members from the house. But insecticides do not provide for the presence of children and pets in the house, which creates certain difficulties.

The indisputable advantage of a homemade rodent trap is the availability of funds. You can make a mouse trap from anything at no extra cost, from a cardboard box from a cake to a plastic bottle.

An important advantage of handmade mousetraps is their reusability. In addition, most of the traps work in such a way that they do not require constant monitoring.

The secrets of choosing the right bait

You can make a mousetrap that will be thought out to the smallest detail, designed for reusable use in automatic mode, but only the right bait will help to achieve the effect.

It is believed that rats and mice are crazy about cheese. Actually this is a stereotype. Indeed, the product does not leave animals indifferent, but it is not their favorite delicacy. Loose ones with a pungent odor are of much greater interest to rodents, for example, bait from:

• sunflower seeds;
• crusts of bread dipped in sunflower oil;
• crackers in sesame oil;
• lard and black pudding.

All these products will attract the attention of rodents, which means they will lure them into pre-prepared traps.

How to make a wooden trap at home?

The desire to make a trap for mice or rats with your own hands and from improvised means fully justifies itself in all respects. Using previously unnecessary materials (remnants from repairs or construction work), you can build really working devices to catch pests.

Wooden mousetraps are one of the most practical options. Such devices can be used for a lifetime, having exterminated a single generation of rodents. At the initial stage, it is worth trying to make a trap for 5 cells. For this, a small piece of timber with parameters 180 × 100 × 60 mm from any tree is suitable, two parts of steel wire with a diameter of 2 mm and 0.2 mm, as well as natural thread No. 30.

The manufacturing process begins with the preparation of holes in the wooden base of the device. In total, such holes will need 35 pieces with a diameter of 1 mm each. The next step is to drill 5 niches with a diameter of 30 mm and a depth of 65 mm. For the device, you will need brackets and springs - they are made from prepared parts of the wire. As soon as the springs are fixed on the base, thin wire chokes are attached with a margin of 15 mm.

The finished mousetrap is charged using a thread. It is threaded into a large needle, a spring is pressed and tied into several knots. The rest of the cells are prepared in the same way. Once all compartments are charged, prepare the bait. These mouse traps work on a simple principle. Rodents are like the smell of bait, they gnaw through the thread to get to it, a spring with a noose is triggered.

Bank and paper - how does the trap work?

A simple option is a mousetrap from a jar, which even a child can make. In order for rodents to be able to climb to the neck of the jar, a kind of “ramp” is built for them, while the bait is placed inside the jar, tightening the throat with paper cut crosswise.

As soon as the mouse touches the paper, its parts will open and the victim will fall into the container. This humane mousetrap is suitable for those who are not ready to take on the responsibility of exterminating mice. It has a significant drawback - a low level of efficiency. Often mice, especially with experience, feel the catch and do not touch the notched paper. Only young individuals who are not able to sense the danger in advance get into the jar.

Bank and coin - how to make a mousetrap?

Another version of the device for catching mice from a jar, this time with a button or a coin. Just like the previous option, the jar will not kill, but will only help to catch rodents in a humane way.

The principle of operation is more than simple. A button, coin or any puck is used as a support, lifting the jar (can be replaced with a pan or bucket). A strong thread with a hook is tied to the support, a rod is placed inside the container to fix the thread, and a bait is put on the hook. The smell of the treat will attract the mouse to the jar, she will pull on the hook, the thread will stretch and drop the puck as a support, as a result of which the rodent will be in the trap unharmed.

By the same principle, a trap can be made from a box, for example, from under a cake. A hole is made in the lid exactly in the middle, where they insert half of the stick with a cotton swab at the end so that it is outside, and the part without the swab is inside the box with the bait.

Any weight is placed on the lid of the box, it can prevent the mouse from trying to get out after the trap slams shut. A bait is attached to a stick inside the box, the edge of the lid is lifted and placed on a small support. The rodent will be attracted by the smell of the bait, it will climb into the box, and when it tries to remove the food from the stick, the box with the weight on the lid will close.

Such homemade mousetraps are quite effective, but they have one significant drawback - they work once, which means they are able to catch one mouse.

//www.youtube.com/watch?v=-1SoXy2gY3o

A bucket of water at the base of the trap - a device

A working mousetrap from a bucket of water is made simply and quickly. To do this, two holes are drilled in the bucket, a metal rod is passed through them with a plastic bottle previously put on it with a lid lubricated with oil for easy rotation.

The neck of the bottle is pulled to the edge of the bucket, and the bait is attached to the middle. The mouse, smelling the smell of food, will climb the bottle, will not be able to stay on the slippery surface and will fall into the water.

Simple and at the same time effective designs of this type of mousetraps allow you to catch several individuals at once in the absence of the owners of the house.

A simple mousetrap from a flower pot - the secret of the device

Orphaned flower pots in the house can be used. One of them is a do-it-yourself mouse trap. The primitive and at the same time effective device of the mousetrap allows you to catch rodents in a short time without much difficulty and expense. It works simply: the pot is turned upside down, set at an angle on a small "gatehouse" by analogy with the jar described above.

The bait is planted at the end of the "gatehouse". As soon as the rodent comes to the smell of the bait, he will make an attempt to remove it from the point, which will lead to the fall of the pot and the slamming of the trap. To prevent the prisoner from escaping, it makes sense to install such traps on plywood sheets that prevent undermining.

Glue mousetraps - how do they work?

Glue traps are also quite easy to make with your own hands, with mouse glue, a base, such as plywood or a plastic pallet, and of course bait.

The base is smeared with special glue for mice (just buy it in a specialized store), a trap is placed in the center. There is nothing complicated about how this type of mousetrap works: a mouse or rat will get close to the treat and stick to the composition of the pallet.

The disadvantage of the trap is not the most humane method of capture. The rodent, sticking to the base, does not die, but tries to free itself for a long time, desperately squeaks and wriggles, at the same time, it is no longer possible to peel it off. For those who find it difficult to endure the suffering of animals, such an option as homemade Velcro for mice will seem inappropriate.

A simple trap made of plastic containers - manufacturing algorithm

A more than simple, and most importantly, humane way to catch rodents at home is to make a trap out of a plastic container. To do this, you will need the following elements:

• plastic bottle;
• thread or rope;
• bait.

A mousetrap is constructed from a plastic bottle simply. The neck is cut off at the container, two holes are made for attaching the thread. The bait is placed inside. One part of the thread is tied to the load or glued to the edge of the table. The container is placed on the table in such a way that most of it hangs from it.

As soon as the mouse comes to the aroma of the bait, it will climb into the bottle and gravity will play a role here - the bottle will fall to the floor along with the rodent, hover above the floor due to the correctly selected length of the thread. Caught prey can be released away from home without stress for her and the household.

Mousetrap "top" - how does it work?

Effective traps for mice at home, also suitable for trapping rats - "tops". Visually, these are structures based on oblong cells with a cone-shaped entrance. At the level of the cut end of the structure, another entrance begins - this is a dead end. Its lower part is the bottom of a smooth plate, fixed by a wide base. The plate is pressed against the cone under the bottom and masks the stroke as a counterweight.

A rat or mouse will try to get inside by smelling the bait. When the attempts are unsuccessful, she will try to move back to make sure the exit is safe, after which she will go inside again and fall into the second cone. Under the weight of the animal, the platform will sink and the victim will fall to the bottom of the trap, after which the structure will be brought back into working condition for new prey. It will be possible to make a design with your own hands, having a ready-made drawing of a trap.

Zürner mousetrap - how to make at home?

Similar to the previous design - a zürner trap at the base with a box, which is masked from the outside with a sloping lid, inside upholstered with galvanized iron. Two opposite sides have inlets or windows, opposite each there is a fixed bridge on a hinge, the ends of which rest on the edges of the holes. The inner ends, without supports, form a long bridge, stretched "over the abyss". A hook with a bait is attached above the bridge closure zone, fixing it on the box lid.

The design works according to the following principle:

• the mouse runs along the bridge to the bait;
• under its mass, the bridge bends and the animal falls to the bottom;
• the bridge returns to its original position.

Is it possible to make a trap at home with such a device? This is possible, and the process of constructing the structure will turn out to be many times simpler than the process of arranging the previous “top” mousetrap.

In spring and autumn, residents of houses and apartments are faced with a problem that is as old as the world - the invasion of mice. They have always caused trouble for people, especially those who have stocks of grain, etc. To fight mice, there are many means and traps that can not always be called humane.

Although they are pests, not everyone can just kill this animal. There are many ways in which you can get rid of uninvited guests in a humane way. Moreover, such methods of struggle do not require you to invest money and effort. We are talking about making a mousetrap from plastic bottles.

Everyone has such a container, so a mousetrap made will cost a penny. Let's find out the advantages of manufacturing these structures and the technology itself.

What is the advantage of a bottle mousetrap

Most traditional mousetraps are quite dangerous if there are children and pets in the house. After all, they can fall into a mousetrap and damage their body parts, and poisons that resemble seeds can attract them. As a result, poisoning and abrasions. In addition, buying a lot of traps for a huge family of rodents is quite expensive.

A plastic bottle mousetrap is good because it will not harm anyone. Children and animals can be calm. And the fact that the creation will require completely simple materials speaks in favor of home-made designs. You will not need much time for manufacturing, since the design is quite simple. Due to its design, the mousetrap is very humane and after catching a rodent, it can simply be released away from home.

Note! Homemade mousetraps are reusable. With one such design, you can catch many mice. It is enough to install it in the right place.

An important component is bait

If you want your mouse trap to be successful, bait is a must. It can be even the most high-tech, however, without a bait, the likelihood of a mouse entering the trap is minimal. Mice are not stupid creatures and will not climb anywhere for fun. Therefore, before considering how to make a mousetrap, you need to figure out the bait for it.

What do mice just love? Cheese? Not really. Undoubtedly, they love him, but this is just a banal stereotype that advertising and television dictate to us. Mice respond much better to sunflower seeds, which are not only tasty, but also smell good. Mice look for food by smell, so smell is important. For greater effectiveness, you can lightly fry them in sunflower oil. In addition, rodents do not disdain bread, which can also be moistened in oil for fragrantness. And to make sure pests go into the mousetrap, take sesame oil. It has a great option.

Advice! You can also use lard, crackers or popcorn.

When you have the right mouse bait in your arsenal, you can start making a trap out of plastic bottles.

Mousetrap from a bottle - option 1

For this simple design, you will need a minimal list of materials. It can be done in 10 minutes. You will need:

• 2 l plastic bottle;
• wire;
• stationery knife.

That's all. In the photo you can see what the finished structure looks like.

So, all you need to do is make one cut and connect the two parts of the bottle. Just? Absolutely. Visually split the bottle in half, identifying the half. The part where the neck is located, visually divide in half again and make a mark. It turns out that you divided the bottle into 2/3. On the mark, using a clerical knife, cut off the top.

You got two elements from a plastic bottle, one is shorter, the other is longer. It remains quite a bit, to collect a mousetrap. It is enough to insert the smaller part into the larger one, neck down. And to fix it, you can use a stapler, wire or glue. The mousetrap from the bottle is ready. It remains to make it effective.

There are two steps for this:

1. Lubricate the neck walls with oil. Not only will it be slippery, but it will also attract mice.
2. Sprinkle seeds or bread crumbs on the bottom.

The mouse will easily fall into the bottle, but will not be able to get out.

Advice! Since the plastic bottle is a light product, the structure may fall and the mouse will come out. To prevent this from happening, strengthen it or simply glue it to a wooden block.

Mousetrap from a bottle - option 2

The second way is not much harder. Even vice versa. The work needs all the same plastic bottle and stationery knife. That's all. The creation technology is as follows:

That's it, the trap is ready. It remains only to place the bait inside. The principle of operation is simple: the mouse will climb inside without problems, but it will not be able to get back, due to the design. As you can see, these are simple options for which you do not need to be an engineer. And in such a mousetrap many rodents can fit.

Mousetrap from a bottle - option 3

This method is already more complicated than the previous ones, but in general it is simpler than simple. Here is what it looks like when finished.

This is where balancing plays an important role. All that is required is to cut off the neck of the bottle. Everything. Next is the matter of technology. In its upper part, as shown in the figure, make a small hole and tie a rope. The length of the rope should be such that, having fallen from the table, the bottle is 5 cm above the floor. One end is tied to a bottle, and the other can be fixed to a shelf, a pipe at a table, etc.

A simple PET bottle mousetrap is shown, but, unfortunately, some of the rodents can escape from it. To improve reliability, several improvements are proposed.

1. Installing the cover on the mousetrap

The mousetrap is made from two identical bottles with a capacity of 1.5-2 liters. In the first bottle, only part of the conical part is cut off, and in the second, the conical part is cut off completely. The conical part of the second bottle will be the cap of the trap.

We make two symmetrical holes on the edges of the conical part of the first bottle for attaching a fishing line and hanging a bottle overturned by a rodent on this fishing line. We attach a lid to the top of the first bottle and mark the centers of two holes with a diameter of 5-7 mm, coinciding with the centers of the holes for the exit of the suspension lines. We make holes in the lid. With my own hands, I pass the fishing line through the holes in the lid and tie it to the first bottle.

Organization of pulling the lid off the table

Mousetrap refinement

If you install the mousetrap in this form, then when capsized, the cap will not close the bottle in any way and most likely will remain on the table. A special pusher is needed to move the cap behind the bottle. The pusher is made of wire in the form of a cropped letter “P”, the width of the upper shelf should be equal to the distance between the holes for attaching the fishing line. We firmly attach the pusher at a distance of ~ 20 cm from the bottle to the fastening lines. When the bottle falls down, the cap placed between the pusher and the bottle will be thrown off the table by the pusher. The pusher at the same time will optimally straighten the fishing lines for the correct lowering of the cap on the bottle.

The operation of the mousetrap is shown in the video.

You can simplify the homemade product by abandoning the pusher, but for this you will have to organize the suspension of the bottle outside the plane of the table.

2. Lengthening the bottle

We take a plastic PET bottle and cut off a section of the conical part, immediately make a hole in the bottom for the mouse to enter. From the first revision, there was a bottle without a neck. We combine the bottles together, we try to achieve a tight connection and, for the reliability of fastening, we wrap the joint with adhesive tape. The result was a bottle of increased length, and even with an additional obstacle from the conical part. We tie the bottle, put the bait at the bottom and set it for fishing.

Tests of such a homemade mousetrap are shown in the video.

Surely a good design will come from two bottles with cut bottoms and one neck. The bottles are combined and also connected with adhesive tape, the presence of a bottom from the conical part during capsizing will further complicate the accurate jump of the rodent to freedom.

An elongated bottle allows you to move the battlefield from buildings to the surrounding area. The combined bottles under the hole for the entrance of the rodent are vertically buried in the ground (carefully so that the structure does not collapse under the weight of the earth). I put the bait inside. We regularly check the results, if necessary, reinstall such mousetraps.

The topic of designing mousetraps is very interesting and will be continued.

In the future, a simple, reliable and very sensitive office floor mousetrap and an automatic reusable mousetrap made of PET bottles will be published.

More material on the topic of mousetraps.

To combat rodents, a lot of preparations and devices are produced: poisons with an attractive smell, spring and electric mousetraps, ultrasonic repellers. As a rule, the acquisition of these funds flies a pretty penny. A do-it-yourself mousetrap is practically free and at the same time does an excellent job of catching rodents.

For people unable to kill an animal, such traps are the only way out: most of them lure the mouse into a trap without causing it the slightest harm. We will figure out how to make a mousetrap at home simply and without much effort.

Disposable traps

Disposable mousetraps will have to be reinstalled after each rodent caught. For their manufacture, improvised materials (ropes, bowls, plastic bottles) and simple tools (scissors and an awl) are used.

1 option

The classic mousetrap is a snap-top lid, making it quick and easy. You need a small container: a jar of 0.5-1 l, a deep plate, a disposable plastic cup. You will also need a coin or a nut, a bait is tied to them with a short rope. The coin is set on the edge and the edge of the container rests on it. The mouse yanks the rope after climbing into the jar, and it falls, preventing the pest from escaping.

This elementary mousetrap from a jar can be improved: instead of a coin, you can cut a rectangle about 2 cm wide from thick cardboard or plastic and sharpen it on one side so that it is convenient to put the bait on it.

Option 2

If food spoiled by rodents is found on the table, a disposable mousetrap from a bottle is most convenient. To make it, you will need a bottle of 1.5 liters, a rope about a meter long, an awl and strong scissors. We cut off the neck from the bottle at a distance of about 5 cm from the cork, pierce the hole at the top with an awl and tie a rope through it to the bottle. The second end of the rope must be fixed on the table, for example, tied to the handle of the pan.

To catch a mouse in such a bottle, it is placed on the edge of the table so that the bottom with the bait hangs in the air. The mouse, having climbed inside, outweighs, the whole structure falls down and hangs on a rope. It remains to drown the rodent or take it outside the house.

3 option

The simplest mousetrap, but at the same time quite effective, is made from a plastic bottle as follows: using a clerical knife, you need to cut the bottle into 2 parts in the place where it begins to narrow.

Turn the neck over and insert into the main part, the sections must be placed at the same level and fastened with tape or glued. A bait is placed at the bottom of the bottle, the neck is lubricated with any edible oil. The mouse, once inside, slides down and cannot get out.

The only difficulty is that this plastic bottle mousetrap should stand so that the mouse can easily reach the neck, for example, near the shelves. For mice, you can make paths so that it is easier for them to climb. Then the bottles will have to be weighted by pouring some stones or sand on the bottom.

reusable traps

Making a reusable mousetrap is not much more difficult, the designs of most of them are elementary and do not require special skills. Such traps can be checked every few days, throwing out the caught rodents. True, they cannot be left for more than a week, otherwise the room will be saturated with the smell of decomposition.

Seesaw principle

The design of the first reusable mousetrap, which is easy to make yourself, is based on the principle of a swing. It will require any container with a volume of 5 liters or more with a wide mouth: a bucket, a saucepan, plastic containers. Across the edge of the bucket, with the help of adhesive tape, a rigid wire, knitting needle or wooden twig is fixed.

You also need a plank a few centimeters wide and a little less than the diameter of the bucket. Suitable, for example, a ruler or a rectangle cut out of thick cardboard, plastic, metal.

We position this plank so that it rests on a knitting needle, one edge lies on the edge of the bucket, and the other with the bait placed on it is in the air. In order for the mouse to climb onto the board, a homemade mousetrap is installed on a stool at the edge of the table. You can make a ramp from the board and attach it to the trap.

To make the trap reusable, the balancing board must be attached to the spoke and positioned so that it returns to its original state.

spinning drum

The basis of this trap is the same as the previous one: a bucket and a bridge leading to it. In order to drop the rodent into the container, a rotating cylinder is used. To make it, you can take a small plastic bottle or a tin can. A small hole is made in the bottom of the bottle, and then it is put on a knitting needle. The needle is placed on the bucket as a continuation of the bridge and fixed.

A mousetrap from a bucket will work for a long time if the bait is placed around the entire circumference of the bottle. You can smear it or attach it with a rubber band. The mouse, attracted by the smell, climbs onto the drum, which turns, and the rodent is in the bucket. If the mouse is not going to be released outside the house, water is poured into the bottom of the bucket so that it chokes.

trap trap

How mousetraps work, easily letting a rodent inside and not letting it go back out. A simple option can be made from the same plastic bottle: cut off the top, and cut the edge of the main part into narrow triangles 5-7 cm long. The resulting teeth are bent inside the bottle, and the bait is placed there. The mouse easily squeezes into a trap between elastic plastic strips, but can no longer get out.

A more complex reusable version of this design can be made from a wooden box. A round hole is cut out in one of its walls at a distance of no more than 5 cm from the bottom. Steel wires 5-7 cm long are inserted along its perimeter at a distance of 1 cm from each other so that they are inside the box. The mouse, having climbed into the hole, falls through the wires and remains inside the box. Rat traps are made in the same way, you just need to increase the diameter of the hole.

glue trap

When catching mice, you can also use special glue from rodents. It is sold in hardware stores and supermarkets in the pest control section. According to the instructions, such glue is smeared on a cardboard box, and a bait is placed in the center. The mouse, hitting it with even one paw, sticks tightly. This is far from a humane mousetrap, the rodent in it dies long and painfully.

The disadvantage of this tool is the ability of the glue to stick to curious pets and smear everything around. You can avoid this by building reusable homemade mousetraps. A hole for a rodent is made in the shoe box on the side, a sheet of paper with applied glue is placed under it inside the box, and a tasty-smelling bait is placed in the depth. After that, it remains only to replace the paper.

Bait selection

World cinema has long inspired everyone that rodents love cheese more than anything in the world. In fact, it is quite difficult to catch a mouse on any dairy products. The most effective way to attract them to traps is to use:

• lard, especially smoked,
• smoked sausage,
• white bread croutons,
• unrefined sunflower oil,
• Sesame oil,
• roasted sunflower seeds and peanuts.

The maximum attraction for rodents is bread soaked in sesame oil.

Baits need to be changed periodically, because mice, sensing danger, stop responding to the smell of treats.

A mousetrap from improvised means will not require special efforts and financial costs, and the result from its use is often better than from industrial products. And in some cases, there is nothing left but to make a mousetrap with your own hands. It will take much less time than looking for a working store late at night or dragging yourself into the city from your summer house. Having decided on what materials are in the house, you can always find the right option from a huge selection of homemade traps.

Residents of private houses, both in cities and in villages, have to deal with gray pests - mice. Unfortunately, cats and hedgehogs can not always help out. You have to install mousetraps.

But, the designs of mousetraps, which are produced by domestic manufacturers, in parallel with the advantages, have disadvantages:

• not only rodents can get into a mousetrap, but also your pet or even worse, a child.
• the design has a tight descent;
• the trap works loudly, blood appears, its smell will scare away other pests;
• danger in the process of charging the mousetrap.

The proposed designs of traps do not have all of the above disadvantages. These do-it-yourself safe mousetraps are made very simply, without requiring special skill.

Do-it-yourself wooden safe mousetrap

Photo No. 1 shows a “safe” mousetrap that you can make with your own hands, for 5 cells. In order to make it, you need a beam, 180x100x60 mm in size, from any type of wood, 2 pieces of steel wire: the first 1.5-2 mm in diameter and the second 0.15-0.2 mm, also cotton thread No. 30.

As you can see, the device of the mousetrap is quite simple.
Photo No. 1, do-it-yourself safe mousetrap: 1 - a piece of steel wire; 2 - a piece of thread; 3 - spring; 4 - bracket; 5 - body; 6 - bait.

Operating procedure:

1. First of all, in a bar of wood, you need to make 35 holes, 1 mm in diameter, according to the markings (photo 2), each.
2. Next, we need to drill 5 niches about 30 mm in diameter, 65 mm deep, as in photo 3.
3. We make springs and brackets.
4. After installing and fixing the springs, we put chokes made of thin steel wire, taking into account that when the springs are parallel to the beam, the wire from the loops is with a margin (10-15 mm).
5. After installing the nooses, we charge the trap. We take a thread and thread it into a long needle, thread it through the holes as in photo 1 and photo 3.
6. We press the spring to the bar and tie the thread into 2-3 knots. We charge the following cells in the same way.
7. When all the compartments are loaded, we put the bait in each of them.

How does the trap work? The smell of the bait we left attracts mice. Since it is located at the end of the cell, in order to get to it, the mouse is forced to gnaw through the thread. As a result, the spring will rise up along with the noose.

Do-it-yourself safe mousetrap from a plastic bottle

This type of trap is more humane. It will not be difficult to make it even for a schoolboy.

1. You will need a PVC bottle and a strong thread or rope. You need to cut off the neck of the bottle, as in the photo.
2. We make 2 holes to secure the thread. Inside the bottle, put the bait on the bottom.
3. We tie one end of the rope to something heavy, or glue it to the edge of the table with tape.
4. We lay the container on the table so that it hangs almost halfway from it.

Smelling the smell of the bait we left, the mouse will climb into the bottle. Thanks to the rodent, the center of gravity will move closer to the bottom, and the bottle will fall off the table along with the victim.

We select the length of the rope so that a safe mousetrap made with our own hands does not touch the floor after falling. On the smooth walls of a plastic bottle, the mouse will not be able to get out, and we will only have to throw the caught “prey” away from home.

If you are looking for simpler options for making a mousetrap with step-by-step recommendations and photos, we recommend the article: "".

Since the owners often have to deal with mice in their home, they accordingly have to take care of their prompt removal. Some people purchase special poisons and mousetraps from specialty stores, and some are ready to make their own hands. In this article, you can learn about how to make a mousetrap with your own hands and some of its advantages.

Many people prefer to use factory-made devices that they buy in stores (glue traps, electrical, mechanical). But in general, the mechanism of operation is very simple, so a do-it-yourself mousetrap is very simple. It is enough to have the right materials to make a quality mousetrap. Some devices can be made using improvised means or material that the owners have already gathered to throw in the trash.

The advantages of this approach include the fact that the production as a whole does not take much time, you can save money if a large number of devices are required. Also, you can independently choose the size of the trap, the principle of operation and other features.

It can also be considered a plus that if the trap breaks after several uses, the owner can always fix it himself or replace it with a new one. For this reason, the question of how to make a mousetrap on your own remains relevant.

Unlike factory-made mousetraps, homemade ones usually do not pose any danger to small children or pets. No hard descent. Also, its operation does not lead to the fact that blood appears, which will scare away other rodents.

Video "How to build a mousetrap from a plastic bottle"

Video instructions for making a simple and effective mousetrap from a plastic bottle.

Types of mousetraps and technology for their manufacture

If you are interested in learning how to make a mousetrap with your own hands, this information will reveal some aspects of their creation.

Mousetraps are disposable and reusable.

Usually, plastic bottles are used to make reusable traps. It is desirable that the neck be wide, since through it the mouse falls into the container itself. The plastic bottle is placed vertically or at a slight angle. Then a bait is placed in it, which exudes a strong smell. It can be fresh cheese, smoked sausage, lard, a piece of meat or peanut butter.

Also, the bottle can be placed in a horizontal position, fixing it on a flat surface. Then a small hole is cut out in the base, and the bait is again placed inside. The design feature lies in its simplicity, but if a mouse gets into it, then it will not work out. The smooth surface of the plastic will not allow the rodent to cling to it, and it will constantly slide off, remaining inside.

If you check it every day, you can catch pests more often. Usually no more than 2 mice can get into the bottle. Others will not climb if they understand the danger of this place. Therefore, periodically the mousetrap needs to be checked.

Disposable traps are made from glass bottles. If the mouse got into the neck, then they will not get out again. But getting them is not easy. Therefore, the bottles are broken or thrown away with the victim.

Such traps are good because they do not kill rodents, but lock them in a small space. This is suitable for people who do not want to hurt these animals. Catching them, you can release them into the field or far away from home. But you should definitely inspect the house or apartment for holes through which they could again enter the room.

You can use a glass jar to make a mousetrap. If there is no empty jar, open the can, eat the contents, and then wash it thoroughly.

Take one liter jar, then roll it up with a lid. If you don't want to roll up, then use an adhesive backing to hold the lid in place. Then you will need to carefully cut the lid from the center to the circumference (like a cake), and bend a little corner inward to clear the way for the mouse.

Inside you need to place a piece of some product - lard, meat or cheese. It is important that he smells good, and thereby attracts rodents to him. If the mouse gets into the jar, then it will not be able to get out of there in any way - sharp teeth and the slippery glass surface of the jar will interfere with it.

A homemade trap can be made from an ordinary bucket. A bucket mousetrap is easy to make and has a simple principle. Take an ordinary bucket, make a hole in two places so that a thin steel rod or rod can be passed through them (for example, 4-5 mm in cross section). Then, on this rod, you will need to string a can of sparkling water or something similar.

It is very important that the jar rotates easily around its axis (along the rod). After that, the rod is threaded through the holes in the bucket, and fixed. You can put something from food in a jar, preferably odorous. The trap is ready. The principle of operation is as follows - the mouse wants to eat what is in the jar, and when it gets inside or on it, the jar will turn. Thus, the rodent will fall into the bucket.

A wooden mousetrap can also be made. A wooden block is taken, and then holes are drilled through which pests can crawl through. As a drill, you need to take a special one, it is used to create holes in the boards during the installation of a wooden floor and other structures.

Absolutely any type of wood that is available to you will do. After that, 4 small holes are drilled from above - two at the beginning, and 2 in the center. They should reach the main hole, a thin thread will be pulled through them.

Then you will need 2 pieces of steel wire (the first is 1.5-2 mm in diameter, the second is 0.15-0.2 mm) and a regular spool of thread. The first will become the basis, and the second will fix the first on the bar.

A spring and a bracket will be made from the wire. A thick piece on one side is wound on a round base to make a curl, and the tip itself is fixed on a wooden block. The tip is located on the back side of the trap (where there is no hole). A small hook is made at the other end.

The threads are threaded through the holes. The central thread is fixed motionless so that the mouse has to gnaw through it, getting to the food, and the outer one hangs freely. Then their ends are fixed on top of a thick wire - the central thread is a knot, and the outer one is a loop on a hook. When the mouse comes for food, it will gnaw through the thread that holds the thick wire spring. Then the loop at the beginning (which is on the hook) of the box will grab the rodent and press it.

Traps with a glue base are made using double-sided tape. A box is taken and its bottom is glued with tape. This material does not lose its properties over time. And little mice will not be able to easily get out of the trap. Food with a pronounced smell is placed in the box, and placed in a remote place so as not to frighten away rodents. In a day, you can check, select the mice caught and take them out of the house.

With the onset of autumn, mice begin to search for warm places for wintering, sometimes overcoming quite long distances. And if in natural conditions animals feed on nuts, seeds or insect larvae, then once they enter a residential building, they become omnivorous, tasting stocks in the pantry, food leftovers in the trash can, and even such inedible things as candles or soap. When rodents enter a human home, getting rid of them can be quite problematic.

Harm from mice to humans

Mice in a relatively short time can cause serious damage to stored vegetables and fruits, spoil cereals and pasta. Pests gnaw wires, arrange nests in various places and carry dangerous infections. The diseases they cause include:

• leptospirosis,
• hemorrhagic fever,
• tularemia
• pseudotuberculosis,
• salmonellosis,
• helminthiasis.

These diseases can be transmitted:

Pests are incredibly prolific - they can bring the first offspring as early as the eighth week after their birth, and replenish the population five to ten times each year. On average, an individual lives for about a year in natural conditions. It is surprising that rodents have not yet flooded the entire planet with such indicators. This does not happen just because the total number of mice is regulated by both natural (natural) factors and human intervention.

How to catch a mouse

It is easier to deal with a pest when you know what it is.

Table: distinguishing features of mice

A medium-sized animal can easily seep into a round gap about a centimeter in diameter and jump in length in an extreme situation up to one meter.

The fight against domestic rodents includes the use of spring mousetraps, glue traps, various kinds of repellers, poisoned baits. At the same time, people have to change tactics all the time, inventing new devices. Live traps are the most humane means of getting rid of rodents and they are quite easy to make with your own hands from improvised materials.

Humane plastic bottle mouse trap

To make such a trap, you will need a plastic bottle, a rope, a heavy object and bait. The rope must be tied to the neck.
The rope must be long enough

We put the bait in the bottle. Mice are most attracted to foods with a strong scent, but scented chemical additives will likely not work.
It is better to use natural products as bait

The bottle should be placed on the edge of a table or other surface. We fix the end of the rope with a heavy object.
Homemade mouse trap installed and ready to go

Live trap from a can with a coin

The manufacture of this mousetrap requires an empty glass jar, coins and bait. Installation takes just a few seconds.
A coin trap is the simplest but very effective way to catch small rodents.

Fix the bait on the inner wall of the jar. Set up the trap as shown in the photo below.
This live trap may require concentration to install

Catching pests with a bucket and ruler

You can catch a boring mouse by using a plastic bucket. To prevent the rodent from jumping out of the container, apply a little vegetable oil to the bottom and walls.
Any sufficiently deep plastic bucket is suitable for catching mice.

The next step is to install a ruler with a bait on the edge of the table. Here it is important to properly balance the mechanism.

The installed ruler with the bait must support the weight of the mouse until the latter gets close to the fragrant piece

Place the bucket exactly in the center of the bait and go about your business with peace of mind. The captured rodent will not be harmed.
A live trap using a bucket and a ruler is installed and configured

Mousetrap from a jar and thick paper

To make the next trap, you need a glass jar, a sheet of thick paper, a rope, a knife and a piece of something tasty.
Cheese, of course, will do, but the mice do not like it too much, oddly enough

We put cheese in a container, cover it with paper and twist it with a rope in the same way as jam jars are corked.
It is advisable to tighten the neck of the container more tightly

Cut the paper on top with a cross with a knife. The corners should be sunk a little deeper.
Using a sharp knife, cut the paper in a cross

Set the trap where the pests are most active. Don't forget to check it from time to time.
Live traps should be checked more often, as a caught pest can escape with some effort.

Another live trap from a plastic bottle

Get an empty plastic bottle. Cut it with a knife along about a third of the total length. Be careful, plastic can slide on the surface.
When working with a knife, be careful not to cut yourself.

Turn the cut part over and fix it with clothespins, paper clips or, for example, hairpins.
The process of making such a live trap will not take much time.

It remains to put goodies in the live trap, put it in the places where mice are active and provide convenience for access.
So that mice can get access to free cheese, we again apply the ruler

barbed mousetrap

To make a trap, you will need the bottom of a plastic bottle cut in half and a knife (or scissors).
The lower half of the plastic container is a live trap blank

Further, being careful, it is necessary to cut out pointed elements with a length approximately equal to half the diameter of the container.
The step width of each element does not play a big role

It remains to put a fragrant piece of banana into the product to lure pests, bend the cutouts inward and wish yourself a successful hunt.
The mousetrap should be installed in places of increased activity of rodents, so the chances of success increase significantly

Video: how to catch a mouse without harming it

How to lure a rodent

Contrary to popular belief, cheese is not the perfect bait for catching mice. Of course, animals will not refuse a piece of fresh product, but if they have a choice, they will prefer seeds or smoked bacon to it.

Table: which products are suitable as bait

Salo	Mice love it. Use fresh, non-rancid product. A stale bacon with a small degree of probability will be of interest to animals.
Sunflower oil	An unrefined fragrant product is best suited for bait. Drip oil on the bread crust, this will attract pests even more.
Bread and grains	Everyone loves fresh baked goods, and mice are no exception. Cereals and bran are somewhat smaller, but also loved by these animals. Wetting a piece of baking with sunflower oil will enhance the effect.
A fish	Rodents love fish, and most of all cold smoked seafood. Such bait must be fresh, mice acutely smell stale fish and will not go for it.
sausages	The option only works if the product is made from natural ingredients. The presence of flavors, flavor enhancers, preservatives and other chemicals will not attract pests.
Cheese	Ordinary cheese is not suitable for bait, use smoked sausage. Again, the presence of chemical components in the latter will not help in catching uninvited guests.

To catch mice even more effectively, it's important to know what rodents don't like. Dried cheese, apples, chocolate, and dry bread crusts will most likely not work.

You should not trap any products with the presence of preservatives, flavors or flavor enhancers in their composition.

Where is the best place to set traps?

The fight against rodents indoors with the help of live traps also implies the correct installation of the latter. To do this, first of all, you need to understand where mice appear, how and when they feed and move.

Did you know that mice really like sunflower oil, smoked bacon and seeds. They are nocturnal animals with very fast metabolic processes of the body, so during the dark time of the day they can go out in search of food up to thirty times. It is very easy to notice that mice were in charge of the house, the animals always leave oblong black litter about one centimeter long.

Mouse droppings reach a length of 0.5-1 cm

As a rule, these animals do not travel long distances in search of food, and usually the animals leave the nest only ten to twenty meters.

Based on this, live traps should be placed along the expected routes of movement of pests, and where they appear most often. It should be noted that mice often move closer to walls and other objects, while being quite inquisitive creatures, they can explore any object in their path.

The appearance of mice in the house or on the site is a very unpleasant event. There are many ways to get rid of unwanted guests in your home, but they all entail the painful death of the captured animal. Read the previously published article - what it is and how it works!

What to do for those who do not want to kill animals, even if they harm people. Yes, and looking at the torn remains of a mouse is an unpleasant sight. It is much more pleasant to remove pests from your home with the help of humane mousetraps. Below are options on how to make a humane mousetrap without much effort.

To make such a mousetrap, you will need a plastic bottle, adhesive tape or plaster, an iron pan or bucket, a small board and an iron twig.

First you need to install the pan in the place where you plan to hunt mice. Next, you need to make two holes: one in the lid, the other at the bottom of the bottle. A metal rod is threaded through the holes - it should not be shorter or longer than the diameter of the pan.

The length of the twig = the inner diameter of the container

The twig is inserted together with the bottle into the pan. Before that, with the help of adhesive tape, a piece of some food is glued to the middle of the bottle. On one side of the pan, you need to install a board at an angle, which will help the mouse get to the bottle.

It is necessary to pour a little water into the container so that the mouse cannot jump out of it after being hit. When the mouse tries to get to the middle of the bottle, it will have to step on it. The bottle will start spinning on the metal rod and the animal will fall into the pan.

A very big advantage of this mousetrap is that with the help of such a device you can catch several mice per night!

Humane mousetrap - liter jar and walnut

This version of the mousetrap is the simplest. You will need to take a liter glass jar, a piece of cardboard or a large plastic lid, as well as a walnut and a piece of bread.

Grinded roasted seeds are also very popular with mice, so they can be used as bait along with bread. The walnut is cracked, all contents are removed from the shell. It will take only one half, which must be filled with bread with seeds. A glass jar is installed on plastic or cardboard. One edge of the jar is raised and a nut is placed under it. The part filled with bait should be directed inside the can. When you try to pull the bread out of the shell, the mouse will be under the jar. By moving the nut towards her, she will block her exit and be trapped.

Humane mousetrap from a plastic bottle: the swing principle

At first glance, the design of this trap may seem complicated and someone will decide that it will be much easier to buy a humane mousetrap. But it's not. No special fixtures are required. The following components of the future mousetrap will be needed: a liter bottle, a clothespin, a thin iron rod, a wooden block.

An iron rod is driven into the middle of a wooden block. Two holes are created in the bottle just above the middle towards the neck. Thanks to them, a bottle without a lid is strung on a rod driven into a wooden block. A clothespin is put on the second tip of the rod so that the bottle does not fly off. Next, a screw is screwed in the upper left corner. It will be the base of the structure that will fix the bottle cap at the same level. The lid should have two holes. Through them, the cap is installed on the pin opposite the neck of the bottle. The lid should not be positioned in the way it is usually positioned to close the bottle, but vice versa.

Inside the bottle is lubricated with bait. The bottle should swing and its upper part, falling down, should rest with the neck against the cork. Thus, the mouse, having made its way into the bottle, will not be able to get out of it, since, making its way to the neck, it will lower the bottle with the weight of its body to the level of the cap, which blocks the exit from the outside.

Humane mousetrap from a bucket

Such a mousetrap is good because it can be used to catch several mice at once. It is better to pour water into a bucket, because mice jump very well. The water will prevent them from jumping out of the trap. A strong iron rod is threaded through the lugs for the bucket holder.

In the middle should be a "springboard" for mice, cut out of a piece of plastic. One end of this plastic board should be adjacent to the edge of the bucket, the other should be suspended. Another important point is to secure the feeder in the middle of the bucket, next to the edge of the plastic. To do this, you can use the same metal rods, fastened together with wire and strung on the main metal rod. In the lid on the feeder you need to put food, trying to get to which, the mouse will fall into a bucket of water. The bait will remain intact, as approaching the edge of the plastic board, the mouse will inevitably fall down.

Conclusion

Any of the above options will help get rid of pests in the house without harming anyone. Materials for the manufacture of such traps are available to absolutely everyone and do not require any cash costs. It is worth making a little effort to enjoy the absence of uninvited guests in your home.