Drilling rig operator job description (general form). Drilling rig operator: features of the profession

Requirements for labor protection and industrial safety rules

1. Drilling of the well shall be carried out in accordance with the operating instructions for the drilling rig, geological documentation and mine surveying instructions.

2. During work, the drilling rig operator must:

carry out constant monitoring of the condition of the sides and roof of the mine;

use personal protective equipment: glasses, gloves, respirators, safety belts, helmets;

Give a warning command to people near the drilling rig and equipment to turn on the drilling unit;

keep hand tools and lifting mechanisms in good working order;

avoid clutter in the workplace;

To carry out the laying of drilling rods so as to prevent their spontaneous rolling;

Carry out repairs only when the power is off.

3. During drilling operations, the drilling rig operator PROHIBITED:

Block up the passages to the workplace and the drilling rig;

Operate mechanisms and tools under loads and pressures exceeding the allowable ones;

violate the operating instructions for the drilling rig;

lower or raise drill rods and stabilizers with unscrewed threaded connections, except for the cases provided for in the operating instructions of the drilling rig (when installing a sludge disposal system);

check or clean threaded connections with bare hands;

bend or bandage air hoses;

carry out any repair or installation work during the operation of the unit;

to drill without means of dust suppression;

remove exhaust air with sludge and water to the existing ore passes and in the direction of people;

use worn out water, air and hydraulic hoses, connect and disconnect them under pressure;

open the electrical unit, carry out repair and maintenance work in it without first disconnecting from the network;

perform any manipulations with the pipelayer if there are people in its area of ​​​​operation;

be in the danger zone of a possible fall of the elements of the drilling string clamped into the pipelayer (rods, stabilizers, etc.);

To clean threaded connections and elements of the drilling tool during the rotation of the drilling string;

jam handles and control buttons of mechanisms with foreign objects;

clean and lubricate rotating mechanisms during operation.

3.8.2.2 The procedure for performing work during the installation (attachment) of the expander

Before starting work on the dismantling of the roller stabilizer, it is necessary to remove the pins in the lower chamber. The dismantling of the roller stabilizer is carried out by a link consisting of 2-4 people, one of which is appointed as a senior.

All operations associated with screwing the roller stabilizer and the sub using a hydraulic tong are performed at the command of the driver from the lower working chamber. At the same time, the drilling rig operator in the upper chamber confirms the acceptance of the commands by phone.

When performing operations to dismantle the roller stabilizer in the lower drilling chamber IT IS FORBIDDEN:

disconnect the stabilizer with the pilot bit and other elements at a height exceeding the height required for complete separation of the threaded parts of the nipples of the connected elements;

be located below the slope from the connected element of the drilling tool, if the soil of the lower working chamber has a slope, stand in the direction of a possible fall of this element;

perform any work without a stable two-way connection between the upper and lower working chambers;

in the event of the formation of a stuffing box that prevents the free exit of water from the annulus, after shutting down the well with the underlying horizon, carry out work to dismantle the stabilizers and install the expander without first completely draining the water from the well.

Expander installation.

The expander is installed in the lower chamber after cleaning it from foreign objects and rock mass residues. The roof of the excavation is cleaned from the fixing rods and should be as flat as possible in relation to the top of the expander, i.e. at an angle of 90 degrees to the well axis.

With a vertical well, the expander is set by the LDM on a horizontal surface; with an inclined well, rock is poured under the bottom of the expander. The reamer is set at the drilling angle of the well, the reamer shank must be located on the same axis with respect to the drilling tool

To give signals, a mining foreman or a worker (senior) on a shift appoints a signalman from among the drill rig operators. The drilling rig operator, located in the upper chamber, is signaled by telephone:

descent of the projectile down - "Maina";

projectile stop - "Stop";

any incomprehensible signal for the drilling rig operator means the “Stop” signal;

Before hanging the expander, it is necessary to strip the stabs in the lower working;

The reamer is to be hung in the lower working according to the operating instructions for the drilling rig.

All operations related to pulling up, setting, screwing in and screwing out the expander should be performed by the commands of the driver from the lower working by phone. At the same time, the senior driver of the drilling rig in the upper chamber confirms the acceptance of commands by phone;

When performing work on the installation - dismantling of the expander IT IS FORBIDDEN:

disconnect the elements of the drilling string at a height exceeding the height required for complete separation of the threaded parts of the nipples of the elements to be connected;

be located below the slope from the detachable element of the drilling tool, if the soil of the lower working chamber has a slope, and stand in the direction of a possible fall of this element;

when setting the coaxiality of the expander with the drill string, be under the expander hanging on the rigging devices;

Perform any work without a stable two-way connection between the upper and lower working chambers;

use faulty rigging devices;

execute unclearly audible or incomprehensible commands;

in the event of the formation of a stuffing box that prevents the free exit of water from the annulus, after connecting the pilot well with the underlying horizon, install the expander without first completely draining the water from the well.

3.8.2.3 The procedure for performing work when expanding vertical mine workings

Expansion of the pilot well is carried out in accordance with the operating instructions for the drilling rig;

Before turning on the drilling rig during expansion, it is necessary to receive an enabling command from the lower working chamber by phone, as well as give a warning command to people near the equipment to turn on the drilling rig and its systems. After making sure that the command is understood, the rotating parts will not harm anyone, there are no foreign objects on them, turn on the drilling rig and get to work;

When performing work on the expansion of the rising IT IS FORBIDDEN:

Expand the pilot well if the slurry cone tightly overlaps the rising cone in the lower chamber.

expand without dust suppression;

during the expansion, be under the riser, near the slurry cone and in the zone of expansion of the falling slurry.

3.8.2.4 Removing the expander

All work on the dismantling of the expander in the lower workings is carried out under the direct supervision of the mining foreman or worker - senior on the shift.

To give signals, the foreman, foreman or senior worker on the shift appoints a signalman from among the drilling rig operators.

Signals to the drilling rig operator in the upper horizon chamber are given by phone:

lifting the projectile up - "Vira";

descent of the projectile down - "Maina";

projectile stop - "Stop";

projectile rotation - "Rotation to the left" or "Rotation to the right";

any incomprehensible signal for the driver of the drilling rig means the signal - "Stop".

3.8.2.5 Dismantling the drilling rig

After lifting the drilling string into the chamber of the upper horizon, the procedure for dismantling the drilling rig should be performed in the reverse order of installation, according to the operating instructions for the drilling rig.

When transferring the drilling rig from the working position to the transport position, it is necessary:

Ensure that hydraulic hoses, electrical cables are not pinched, crushed or torn;

when disconnecting hoses and cables, close the connectors with special plugs;

make sure that the working pressure in the hydraulic system of the drilling rig does not exceed 55 kgf/cm².

It is forbidden to transfer the machine from the working position to the transport position together with the base plates, if the anchor fastening and turnbuckles are not removed.

3.8.2.6 Elimination of accidents when drilling a pilot well or expanding it

In the event of an emergency (drill string breakage, reamer breakage, drilling string jamming, etc.), the drilling rig operator immediately reports the incident to the site manager or mining foreman, and in their absence, to the mine dispatcher.

The liquidation of accidents is carried out according to individual measures developed by the head of the section that carries out work on the implementation of vertical mine workings using drilling rigs of the named type and approved by the chief engineer of the Severny mine.

The head of the site operating drilling rigs "Robbins", and in his absence - the person replacing him, is the responsible manager of the work to eliminate accidents.

3.8.2.7 Transportation of drilling rigs, auxiliary equipment, technological cargoes for drilling rigs of the Robbins type

Transportation on a rigid hitch, loading into the LDM bucket, unloading from the LDM bucket, transportation of drilling rigs, auxiliary equipment and technological cargo in the LHD bucket is carried out according to the project for organizing work on the delivery of drilling rigs, auxiliary equipment and technological cargo using LHD. Loading, delivery and unloading of drilling equipment for sinking vertical mine workings to the work site is carried out by the machinists of the Robbins type drilling rig using LHD. Moving the equipment over a short distance is carried out using a caterpillar conveyor, which is included in the drilling rig kit.

The order of delivery of drilling equipment such as "Robbins" in the buckets of diesel load-hauling machines in underground workings.

Transportation of drilling equipment of the "Robbins" type is allowed for LHD drivers who have at least one year of practical driving experience in underground workings and who have passed the appropriate briefing.

LHDs intended for transportation of Robbins type drilling equipment must be in full technical serviceability and meet the following requirements:

have proper lighting;

have serviceable hydraulic equipment that excludes spontaneous movement of the LHD bucket;

the bucket of the machine must be cleaned of rock mass and other foreign objects;

the LHD bucket must be fixed in the transport position, excluding its overturning;

have fire extinguishing equipment (autonomous fire extinguishing system, OP-10 fire extinguishers in the amount of at least 2 pieces).

All loading and unloading operations are performed only after the full stop of the LHD and the receipt of an enabling command from the driver of the LHD.

When performing loading and unloading operations, the LHD must be set to the parking brake on the horizontal section of the mine working.

All equipment moved in the LHD is secured with a safety cable. When moving a drilling rig on a rigid hitch using a LHD, the rig is also fixed with a safety cable, while it is necessary to ensure that during movement the equipment being moved does not touch the sides and roof of the working, lining elements, pipelines and cable routes.

Transportation of the drilling equipment of the Robbins rigs is carried out accompanied by a mining foreman (senior operator of the drilling rig), who, together with the driver of the LHD, is responsible for the delivery and safety of the drilling equipment. The speed of the LHD must not exceed 5.0 km/h.

When moving LHD with drilling equipment, the bucket must be in front in the direction of travel in the field of view of the driver. When escorting the LHD along horizontal workings and when moving up the slope, the mining foreman (senior operator of the drilling rig) must be in front of the LHD in the visibility zone of the LHD driver. When escorting the LHD when moving down the slope, the mining foreman (senior operator of the drilling rig) is behind the LHD in the visibility zone of the LHD driver.

The movement of LHD with drilling equipment at the junctions of mine workings should be carried out at a speed of 1.5 km / h with an audible signal and headlights on.

The speed of movement when moving the drilling rig on a rigid hitch (drag) in narrow places of workings or on turns should be reduced to a minimum, the mining foreman (senior drill rig operator) must warn the driver of the LHD about this.

LHDs engaged in the transportation of drilling equipment, when moving through mine workings, have an advantage over other vehicles, except for vehicles engaged in the transportation of explosives.

When transporting drilling rigs, auxiliary equipment and technological cargo for drilling rigs of the Robbins type, it is prohibited:

To transport drilling equipment on machines that have technical malfunctions, as well as not equipped in accordance with the requirements of this Regulation - when loading, unloading and transporting drilling equipment, perform any manipulations with the LHD bucket;

Exceed the established speed of movement when transporting drilling equipment;

accompany the LHD during the movement of equipment, following next to the machine or the equipment being moved;

be on a slope below the LHD, conveyor or moving equipment when unloading, loading and hitching equipment without taking measures against their arbitrary rolling;

when installing an oil station, electric unit or safe in the working chamber with the help of a LHD or a conveyor, be between them and the blocks, as well as the blocks and the side of the development;

use faulty towing or safety devices;

When installing an oil station, electric unit, control panel or safe in the chamber with the help of LDM, it is forbidden to be between the blocks, as well as between the blocks and the side of the mine.

The procedure for the personnel delivering drilling equipment when the emergency response plan is put into effect at the mine:

PDM driver:

If possible, place the vehicle on a level surface;

Sets it to the parking brake and shuts off the engine;

Places wheel chocks under the wheels of the LHD;

Mining foreman (senior operator of the drilling rig) protects the LHD with drilling equipment with a full house from the side of possible approaches.

Loading of equipment is carried out by machinists of the Robbins type drilling rig under the guidance of a mining foreman (chief rig operator).

On all sides of the possible passage of self-propelled vehicles, as well as to warn people, the workplace is fenced with notices that prohibit the passage of cars and the passage of people. Full houses are set up personally by the mining foreman (chief driver of the drilling rig) at least 25 m from the place of work, and at haulage workings with rail transport - at least 60 m.

If necessary, the passage of vehicles or the passage of people, the order of passage or passage is determined by the mining foreman (senior operator of the drilling rig), who personally removes the notices and makes the pass of equipment and people.

In the case of a large weight of equipment, loading and unloading is carried out using lifting mechanisms by specially trained machinists of the Robbins type drilling rig, who have the appropriate certificates.

The bucket or loading platform is loaded in such a way that the equipment and tools being transported do not protrude beyond the dimensions of the machine.

Transportation of drilling rigs and auxiliary equipment in workings of haulage horizons is carried out according to separate measures developed by the head of the site operating the Robbins drilling rigs, the head of the site of the VSHT mine and the approved chief engineer of the Severny mine.

3.8.2.8 Maintenance and repair of Robbins drilling rigs

Maintenance and repair of Robbins drilling rigs is carried out in accordance with the manufacturer's instructions.

3.9. Mining and preparation works and fixing of workings during mining by the POCC system

Mining and preparatory work is carried out immediately before the development of the chambers, and consists in driving drilling and delivery workings within the boundaries of the mining block. The sections of workings in the treatment blocks and the technology for their implementation must comply with the type passports adopted at the mine.

Development workings ensure the safe movement of people and self-propelled equipment in the mining block, the minimum distance of ore delivery, the supply of the required amount of air to each working development, and the required intensity of mining. The number and location of development workings in the block was chosen taking into account the conditions of occurrence of ore bodies and the accepted version of the development system.

To drill the chamber stocks of the YuZRT-1 from the field drifts of the lying side, drilling orts are passed along the roof and soil of the chambers.

For shipment of the ore beaten in the chamber, delivery orts are passed in the soil of the MCC, from which loading races are passed through 20 m (along the axes of the workings) along the length of the chamber. To ensure transport communication, the transport races passed along the hanging side are merged with each other. To ensure better penetration of the LDM ladle into broken ore, it is recommended to design the outlet bottom with a displacement of the haulage orifice by 2 m from the central axis of the pillar.

During the development of the ZRT, the main preparatory workings are the drilling drifts and loading bays that are passable on each sublevel. To unload the ore from the chambers, the sublevel field drifts are connected with the drilling drifts by loading runs every 12.5 m (along the axes). With a width of the races of 4 m, the width of the pillar between them will be 8.5 m. To save the races from destruction during blasting in the chamber, they are passed after blowing up the opposite fans.

A complex of self-propelled equipment is used in the sinking of horizontal workings: drilling of holes - drilling carriages of the "Boomer" type, loading of the face - chargers of the "Charmek" type; load capacity 7-12 tons of the Toro type, transportation of rock mass - dump trucks with a capacity of 30 tons of the Toro type. Roofing is erected with the help of "Utilift" installations, shotcrete - with the help of "Spreimek" self-propelled installation.

The fixing of workings is carried out in accordance with the fixing passport approved by the Chief Engineer of the mine. Types, parameters and technology of fastening preparatory - threaded workings are defined in TI 48200234-2-44-02, compiled taking into account the experience accumulated by the mines of the plant and the requirements of Gosgortekhnadzor.

3.10. Mining and preparation works and fixing of workings during mining by the POT system

The horizon preparation scheme determined by the local project should, as a rule, ensure the independent operation of each sublevel in terms of ore shipment, ventilation of tunneling and clearing operations, and collapse of overlying rocks.

Mining and development workings include sublevel field drifts, auto-slopes, ore passes and ventilation risers, and rifled workings include haulage orts (DO) and boring haulage drifts (BDSH).

Field sublevel drifts should be located 15-20 m from the ore body.

Ore passes and ventilation-running rising, connecting sublevel and floor workings, are passed as necessary during the development of mining operations on the sublevel.

The subfloor is divided into blocks by delivery vectors. The length of the block (the distance between the haulage drifts) at the initial stage of mining is assumed to be 50 m; with the development of work, it can be increased to 100 m.

The cutting work in the block includes the driving of haulage ores at each sublevel every 50 meters, drilling haulage drifts every 12 meters (their number is determined by the horizontal thickness of the ore body and substandard ores being blasted, at least 20 m and cut risers, by the method of sectional blasting of wells).

The cross section of the rock part of haulage orts and boring haul drifts, drilling drifts is accepted by the project 15.9 m 2 , field sublevel drifts - 19.5 m 2 and ore passes of about 6.5 m 2 . The gaps in the BDSh are chosen to be minimal, since the presence of miners in them, except for the LHD driver, is not provided for during shipment.

The preparation of the flank reserves of the Central area during the development of underpit and edge reserves is carried out according to the results of the refined morphology of the deposit and differs somewhat from the design scheme for the preparation of reserves.

Types and parameters of fastening of field mining and preparation floor and sublevel workings are accepted in accordance with TI 48200234-2-44-02, compiled taking into account the experience accumulated by the mines of the plant and the requirements of Gosgortekhnadzor. Mining and preparation workings are fixed mainly with reinforced concrete rods and in some areas with combined support (shotcrete, rods). The maximum period of existence of threaded workings is about 6 months.

Quarterly report Open Joint Stock Company Mining and Metallurgical Company Norilsk Nickel Issuer code 40155-f for the 2nd quarter of 2006

... production objects (dangerous production objects, on the which are being mountainworkon the mines and undergroundmines ... workon themine "Northern" on the... highly efficient technologicalprocesses; ...

APPROVE
Supervisor "_____________"
_____________ (____________)

JOB DESCRIPTION
DRILLING RIG OPERATOR OF __-TH DISTRIBUTION

1. GENERAL PROVISIONS

1.1. This job description defines the functional duties, rights and responsibilities of a drilling rig operator of the __th category "_______________" (hereinafter referred to as the "Organization").
1.2. The driver of the drilling rig of the __th category is appointed to the position and dismissed from the position in accordance with the procedure established by the current labor legislation by order of the Head of the Organization.
1.3. The driver of the drilling rig of the __th category reports directly to the ____________________ Organization.
1.4. A person with ________ professional education and ____ years of work experience in the specialty (without presenting requirements for work experience) is appointed to the position of a drilling rig operator of the __th category.
1.5. The rig operator must know:
- purpose, device, rules for installation, dismantling and operation of drilling and power equipment, their characteristics;
- designs of drilling rigs and masts, rules for their assembly and disassembly;
- technological regimes, rules and methods of drilling and expanding wells with and without core sampling under normal and complicated conditions;

Note. Access to the entire contents of this document is restricted.

In this case, only part of the document is provided for review and avoiding plagiarism of our developments.
To gain access to the full and free resources of the portal, you just need to register and log in.
It is convenient to work in advanced mode with access to paid resources of the portal, according to

Characteristics of works. Management of drilling rigs and installations of various types, including self-propelled on the basis of a tractor, when drilling and expanding wells. Installation, dismantling, relocation, preparation for work, installation and regulation of drilling equipment, planning and clearing the site for its installation. Marking of wells according to the passport for drilling operations. Management of the drilling process depending on geological conditions, the occurrence of complications, the state of drilling equipment and tools. Cementation, grouting, casing wells, other works provided for by the technological regulations and regime and technological documentation. Tripping, extension of rods, extraction of pipes. Choice of axial force, tool rotation speed, amount of flushing fluid supplied, air to ensure optimal drilling conditions. Observation of indications of instrumentation. Regulation of drilling process parameters to obtain optimal penetration rates. Performance of work on the prevention and elimination of curvature, accidents and complications in wells. Preparation of flushing liquids and cement mixtures. Control of parameters of washing liquids. Restoration of water loss of rocks in wells, installation of filters and water-lifting means. Selection of drills, bits and drill bits, changing them during drilling. Cleaning, flushing, lubrication of wells. Maintenance of compressors installed on drilling equipment, mobile compressors operating in combination with a drilling rig (machine), gasified installations used in fire drilling, pumps, liquid oxygen tanks and other auxiliary equipment. Fishing works, wellhead shut-in. Identification and elimination of malfunctions in the operation of the serviced equipment and tractor, participation in their repair. Replacement of engines, automatic machines, starters. Participation in the preparation of instruments and wellhead devices for special geophysical, hydrogeological and other studies. Carrying out liquidation works. In necessary cases - sampling of core, drill cuttings, rock samples and determination of the category of rock strength by drillability. Land reclamation upon completion of drilling operations. Slinging and loading and unloading operations at the drilling rig. Maintenance of primary technical documentation.

Should know: purpose, device, rules for installation, dismantling and operation of drilling and power equipment, their characteristics; designs of drilling rigs and masts, rules for their assembly and disassembly; technological regimes, rules and methods of drilling and expanding wells with and without core sampling under normal and complicated conditions; geological and technical order for the well; content and procedure for filling out the passport of drilling and blasting operations; the purpose and essence of cementation, bituminization of silicification, plugging and freezing of wells; purpose, composition, methods of preparation and processing of washing liquids, rock strength reducers and complex injection solutions; purpose, characteristics, types of tools, devices and materials used; requirements for the quality of filling drilling tools, depending on the strength of the drilled rocks; ways to control the drilling process, taking into account geological conditions, the occurrence of complications depending on the state of drilling equipment and tools; conditions and forms of occurrence of minerals; causes of technical malfunctions and accidents, measures for their prevention and elimination; instructions for sampling and storage of core; ways of performing fishing operations; fundamentals of geology, hydrogeology, mining, electrical engineering, hydraulics, pneumatics; name and location of mine workings; classification and properties of rocks; land reclamation methods; rules for maintaining primary technical documentation, its forms; device and scheme of the power network and methods for eliminating current leaks; methods and rules for the production of slinging works; arrangement of a tractor and a self-propelled unit, rules for their operation and repair; accident elimination plan, rules for safe blasting.

When drilling exploration wells for solid minerals with first-class drilling rigs (with a lifting capacity of up to 0.5 tons), motor drills, manual and portable sets, rods - 3rd category;

when drilling: wells with non-self-propelled rotary percussion drilling machines, self-propelled rotary drilling machines with an engine power of up to 50 kW, sounding drilling machines from underground mine workings; exploration wells for solid minerals by drilling rigs of the second class (hook capacity from 0.5 to 1.5 tons); hydrogeological and geophysical wells using a rotary method without the use of a cleaning agent, percussion and other drilling methods; when drilling oversized with self-propelled drilling rigs, perforators, electric drills - 4th category;

when drilling: wells with cable-and-percussion drilling machines, self-propelled rotary drilling machines with an engine power of more than 50 kW, self-propelled rotary percussion drilling machines with an engine power of up to 150 kW, self-propelled roller-cone drilling machines with an engine power of up to 300 kW, machine tools from underground mine workings, except for sounding drilling machines; exploration wells for solid minerals by drilling rigs of the third, fourth and fifth classes (hook capacity from 1.5 to 15 tons); hydrogeological wells by rotary drilling with the use of a cleaning agent; when extracting (drilling out) a mineral from thin layers with auger-drilling machines and machines for underground work - 5th category;

when drilling: wells with self-propelled rotary percussion drilling machines with an engine power of 150 kW or more (or equipped with hydraulic systems), self-propelled roller-cone drilling machines with an engine power of 300 kW or more, thermal drilling machines, vibro-rotary drilling machines; exploration wells for solid minerals by drilling rigs of the sixth, seventh and eighth classes (hook capacity over 15 tons); when extracting (drilling out) a mineral from thin layers with auger-drilling machines and machine tools in open-cast mining - 6th category.

Notes:

1. According to this tariff-qualification characteristic, work and workers employed in the drilling of wells of all types are charged, except for oil and gas wells, during the drilling of which workers and work are charged according to ETKS, issue 6,.

2. When drilling exploration wells using special technical tools that improve the quality of geological testing and drilling speed, establish and maintain a given direction of the wellbore (drilling using complexes with removable core receivers, hydraulic hammers and pneumatic hammers, with hydrotransport of the core; directional and multilateral drilling) ; when drilling exploration wells in difficult mining and geological conditions; when drilling exploratory wells in the fields worked out by mines (when drilling wells through worked out seams), the billing is one category higher.

3. Classes of drilling rigs for drilling exploration wells for solid minerals are approved by state standards and include: drilling depth, initial and final diameter of wells, hook load capacity, drive motor power, drill assembly rotation speed, inclination angle, lifting speed, length drill candle.

4. Engine power of drilling equipment is taken as the total power of electric motors installed on this equipment.

5. Assistants to the drilling rig operator who have mastered the entire range of work provided for in the tariff and qualification characteristics of the drilling rig operator are charged one category lower than the drilling rig operator with whom they work, and two categories lower if the entire range of work has not been mastered.

6. In the absence of assistants to the drilling rig operator, mobile compressors are serviced by mobile compressor operators (with different engines), which are charged according to ETCS, issue 3,.

Instruction:

Using the information in this article and the methodology for creating a job description, develop a job description. To evaluate your work, create a topic on the forum. We will always help and appreciate.

APPROVE:

________________________

[Job title]

________________________

________________________

[Name of company]

________________/[FULL NAME.]/

"____" ____________ 20__

JOB DESCRIPTION

Drilling rig operator of the 6th category

1. General Provisions

1.1. This job description defines and regulates the powers, functional and job duties, rights and responsibilities of the 6th category drilling rig operator [Name of organization in the genitive case] (hereinafter referred to as the Company).

1.2. The driver of the drilling rig of the 6th category is appointed to the position and dismissed from the position in accordance with the procedure established by the current labor legislation by order of the head of the Company.

1.3. The drilling rig operator of the 6th category belongs to the category of workers and reports directly to [name of the position of the immediate supervisor in the dative case] of the Company.

1.4. The driver of the drilling rig of the 6th category is responsible for:

• timely and high-quality performance of tasks for their intended purpose;
• compliance with performance and labor discipline;
• observance of labor safety measures, maintenance of order, compliance with fire safety rules at the work site (workplace) entrusted to him.

1.5. A person who has a secondary vocational education in this specialty and at least 1 year of work experience is appointed to the position of a drilling rig operator of the 6th category.

1.6. In practice, the driver of a drilling rig of the 6th category should be guided by:

• local acts and organizational and administrative documents of the Company;
• internal labor regulations;
• rules of labor protection and safety, ensuring industrial sanitation and fire protection;
• instructions, orders, decisions and instructions of the immediate supervisor;
• this job description.

1.7. The driver of the drilling rig of the 6th category must know:

• purpose, device, rules for installation, dismantling and operation of drilling and power equipment, their characteristics;
• designs of drilling rigs and masts, rules for their assembly and disassembly;
• technological regimes, rules and methods of drilling and expanding wells with and without core sampling under normal and complicated conditions;
• geological and technical order for the well;
• content and procedure for filling out the passport of drilling and blasting operations;
• the purpose and essence of cementation, bitumization, silicification, plugging and freezing of wells;
• purpose, composition, methods of preparation and processing of washing liquids, rock strength reducers and complex injection solutions;
• purpose, characteristics, types of tools, devices and materials used;
• requirements for the quality of filling drilling tools, depending on the strength of the drilled rocks;
• ways to control the drilling process, taking into account geological conditions, the occurrence of complications depending on the state of drilling equipment and tools;
• conditions and forms of occurrence of minerals;
• causes of technical malfunctions and accidents, measures for their prevention and elimination;
• instructions for sampling and storage of core;
• ways of performing fishing operations;
• fundamentals of geology, hydrogeology, mining, electrical engineering, hydraulics, pneumatics;
• name and location of mine workings;
• classification and properties of rocks;
• land reclamation methods;
• rules for maintaining primary technical documentation, its forms;
• device and scheme of the power network and methods for eliminating current leaks;
• methods and rules for the production of slinging works;
• arrangement of a tractor and a self-propelled unit, rules for their operation and repair;
• accident elimination plan, rules for safe blasting.

1.8. During the period of temporary absence of the driver of the drilling rig of the 6th category, his duties are assigned to [name of the position of the deputy].

2. Job responsibilities

The driver of the drilling rig of the 6th category performs the following labor functions:

2.1. Management of drilling rigs and installations of various types, including self-propelled tractor-based, during drilling:

• wells with self-propelled rotary percussion drilling machines with an engine power of 150 kW or more (or equipped with hydraulic systems), self-propelled roller-cone drilling machines with an engine power of 300 kW or more, thermal drilling machines, vibro-rotary drilling machines;
• exploration wells for solid minerals by drilling rigs of the sixth, seventh and eighth classes (hook capacity over 15 tons);
• when extracting (drilling out) a mineral from thin layers by auger-drilling machines and machine tools in open-cast mining.

2.3. Marking of wells according to the passport for drilling operations.

2.4. Management of the drilling process depending on geological conditions, the occurrence of complications, the state of drilling equipment and tools.

2.5. Cementation, grouting, casing wells, other works provided for by the technological regulations and regime and technological documentation.

2.6. Tripping, extension of rods, extraction of pipes.

2.7. Choice of axial force, tool rotation speed, amount of flushing fluid supplied, air to ensure optimal drilling conditions.

2.8. Observation of indications of instrumentation.

2.9. Regulation of drilling process parameters to obtain optimal penetration rates.

2.10. Performance of work on the prevention and elimination of curvature, accidents and complications in wells.

2.11. Preparation of flushing liquids and cement mixtures.

2.12. Control of parameters of washing liquids.

2.13. Restoration of water loss of rocks in wells, installation of filters and water-lifting means.

2.14. Selection of drills, bits and drill bits, changing them during drilling.

2.15. Cleaning, flushing, lubrication of wells.

2.16. Maintenance of compressors installed on drilling equipment, mobile compressors operating in combination with a drilling rig (machine), gasified installations used in fire drilling, pumps, liquid oxygen tanks and other auxiliary equipment.

2.17. Fishing works, wellhead shut-in.

2.18. Identification and elimination of malfunctions in the operation of the serviced equipment and tractor, participation in their repair.

2.19. Replacement of engines, automatic machines, starters.

2.20. Participation in the preparation of instruments and wellhead devices for special geophysical, hydrogeological and other studies.

2.21. Carrying out liquidation work.

2.22. In necessary cases, the selection of core, drill cuttings, rock samples and the determination of the category of rock strength by drillability.

2.23. Land reclamation upon completion of drilling operations.

2.24. Slinging and loading and unloading operations at the drilling rig.

2.25. Maintenance of primary technical documentation.

In case of official necessity, the driver of a drilling rig of the 6th category may be involved in the performance of duties overtime, in the manner prescribed by law.

3. Rights

The driver of the drilling rig of the 6th category has the right:

3.1. Get acquainted with the draft decisions of the management of the enterprise relating to its activities.

3.2. Submit proposals for the management to improve the work related to the responsibilities provided for in this job description.

3.3. Report to the immediate supervisor about all the shortcomings in the production activities of the enterprise (its structural divisions) identified in the course of the performance of their duties and make proposals for their elimination.

3.4. Request personally or on behalf of the immediate supervisor from the heads of enterprise departments and specialists information and documents necessary for the performance of their duties.

3.5. Involve specialists from all (individual) structural divisions of the Company in solving the tasks assigned to him (if it is provided for by the regulations on structural divisions, if not, with the permission of the head of the Company).

3.6. Require the management of the enterprise to assist in the performance of their duties and rights.

4. Responsibility and performance evaluation

4.1. The driver of a drilling rig of the 6th category bears administrative, disciplinary and material (and in some cases provided for by the legislation of the Russian Federation - and criminal) responsibility for:

4.1.1. Non-fulfillment or improper fulfillment of official instructions of the immediate supervisor.

4.1.2. Failure to perform or improper performance of their labor functions and assigned tasks.

4.1.3. Unlawful use of the granted official powers, as well as their use for personal purposes.

4.1.4. Inaccurate information about the status of the work entrusted to him.

4.1.5. Failure to take measures to suppress the identified violations of safety regulations, fire and other rules that pose a threat to the activities of the enterprise and its employees.

4.1.6. Failure to enforce labor discipline.

4.2. Evaluation of the work of the driver of the drilling rig of the 6th category is carried out:

4.2.1. The immediate supervisor - regularly, in the course of the daily implementation by the employee of his labor functions.

4.2.2. Attestation Commission of the enterprise - periodically, but at least once every two years based on the documented results of the work for the evaluation period.

4.3. The main criterion for evaluating the work of the driver of a drilling rig of the 6th category is the quality, completeness and timeliness of his performance of the tasks provided for in this instruction.

5. Working conditions

5.1. The mode of operation of the drilling rig operator of the 6th category is determined in accordance with the internal labor regulations established by the Company.

5.2. In connection with the production need, the driver of the drilling rig of the 6th category is obliged to go on business trips (including local ones).

Acquainted with the instruction __________ / ____________ / "____" _______ 20__

(signature)

Notes:

1. According to this tariff-qualification characteristic, the works and workers employed in the drilling of wells of all types are charged, except for oil and gas wells, for the drilling of which workers and works are charged under the “Drilling of wells” section.

2. When drilling exploration wells using special technical tools that improve the quality of geological testing and drilling speed, establish and maintain a given direction of the wellbore (drilling using complexes with removable core receivers, hydraulic hammers and pneumatic hammers, with hydrotransport of the core; directional and multilateral drilling) ; when drilling exploration wells in difficult mining and geological conditions; when drilling exploratory wells in the fields worked out by mines (when drilling wells through worked out seams), the billing is made one category higher.

3. Classes of drilling rigs for drilling exploration wells for solid minerals are approved by state standards and include: drilling depth, initial and final diameter of wells, hook load capacity, drive motor power, drill assembly rotation speed, inclination angle, lifting speed, length drill candle.

4. Engine power of drilling equipment is taken as the total power of electric motors installed on this equipment.

5. Assistants to the drilling rig operator who have mastered the entire range of work provided for in the tariff and qualification characteristics of the drilling rig operator are charged one category lower than the drilling rig operator with whom they work, and two categories lower if the entire range of work has not been mastered.

6. In the absence of assistants to the driver of the drilling rig, mobile compressors are serviced by drivers of mobile compressors (with a different engine), who are charged according to the section.