Esbe valves are one of the most reliable and functional components used in various water supply systems, including domestic and main ones. It has a very wide range, which includes: rotary vrg131, dn25, as well as other popular varieties.
Currently, a three-way rotary sample of such equipment can be installed in every home. In order to do it right, let's look at the intricacies of working with such equipment and the features of its use.
Article content
Esbe valves are a variety of devices used to control a liquid or gas when it is supplied from one pipe to another. The three-way type of valves is distinguished by the presence of three connections that allow you to effectively redirect the flows in the system, especially in the case of mixing hot and cold water.
Adjusting the operation of valves of this type within the same system can realize the servo. This device needs a little more attention.
Servo. This is a separate element in the system that controls the position of the valves. The servo drive is usually the most affordable and easy to install, which is why it is most often used for.
According to the design features, the servo drive can be different, most often the category of such devices includes. For example, this can be installed with vrg131 samples. Today they provide the highest quality and accuracy in system maintenance, which is why they are so popular among consumers.
In some devices, a servo drive, as well as motor control is not used. In such cases, such special devices are used as for adjusting the operation of the equipment.
Such varieties include, for example, a dn25 valve, which can be mounted in a crane without a drive.
This type of product can be used in a wide range of systems, including heating systems, even centralized, hot, cold water supply, as well as air conditioning.
These types of valves are suitable for various systems, including those operating on oil products, gas, as well as eco-fuels, including solar energy or wind energy. It is possible to install these types of equipment, for example, a three-way rotary valve vrg131, both for central water supply networks and for home networks.
You can pick up a product for any crane. It is only important to choose the right type of product and install it according to the recommendations. Also, for the system to work properly, it is very important to adjust the servomotor or thermostatic controller.
Then the model chosen by you will work without failures, irrespective of the set technical parameters.
Among the main advantages of installing exactly Esbe products are:
Currently, the following models of Esbe valves are especially popular on sale:
The Swedish company ESBE (Esby) has been a recognized leader in the field of water heating and cooling control systems for many years. ESBE VRG 131 and 3F three-way mixing valves and ESBE ARA and 90 series electric actuators are an example of excellent quality and reliability at an affordable price. Esbe's wide range of mixing valves allows you to make the best choice depending on the requirements of the system. High quality brass alloys or cast iron are used as materials. The valves are available with threaded or flanged connections.
Model | vendor code | DN, mm | Connection | Kvs, m³/h | Weight, kg | Replaces |
---|---|---|---|---|---|---|
VRG131-15-0.4 price >> | 11600100 | 15 | Rp 1/2" | 0,4 | 0,40 | - |
VRG131-15-0.63 price >> | 11600200 | 15 | Rp 1/2" | 0,63 | 0,40 | - |
VRG131-15-1 price >> | 11600300 | 15 | Rp 1/2" | 1,0 | 0,40 | - |
VRG131-15-1.6 price >> | 11600400 | 15 | Rp 1/2" | 1,6 | 0,40 | - |
VRG131-15-2.5 price >> | 11600500 | 15 | Rp 1/2" | 2,5 | 0,40 | 3MG15, 3G15 |
VRG131-15-4 price >> | 11600600 | 15 | Rp 1/2" | 4,0 | 0,40 | - |
VRG131-20-2.5 price >> | 11600700 | 20 | Rp 3/4" | 2,5 | 0,43 | - |
VRG131-20-4 price >> | 11600800 | 20 | Rp 3/4" | 4,0 | 0,43 | - |
VRG131-20-6.3 price >> | 11600900 | 20 | Rp 3/4" | 6,3 | 0,43 | 3MG20, 3G20 |
VRG131-25-6.3 price >> | 11601000 | 25 | Rp 1" |
6,3 | 0,70 | - |
VRG131-25-10 price >> | 11601100 | 25 | Rp 1" |
10 | 0,70 | 3MG25, 3G25 |
VRG131-32-16 price >> | 11601200 | 32 | Rp 1 1/4" | 16 | 0,95 | 3MG32, 3G32 |
VRG131-40-25 price >> | 11603400 | 40 | Rp 1 1/2" | 25 | 1,68 | 3G40 |
VRG131-50-40 price >> | 11603600 | 50 | Rp 2" |
40 | 2,30 | 3G50 |
VRG132-25-10 price >> | 11602500 | 25 | G 1 1/4" | 10 | 0,70 | 3MGA25 |
VRG132-32-16 price >> | 11602600 | 32 | G 1 1/2" | 16 | 0,95 | 3MGA25 |
Flanged mixing valves Esbe 3F, 4FESBE 3F, 4F flanged mixing valves are made of cast iron and are widely used in heating and cooling systems. Esbe 3F valves can be used in closed systems with water free of dissolved oxygen. When the Esbe 3F, 4F valve is operating, the hotter coolant is mixed with the cold one entering the boiler, which ensures an increase in the temperature of the coolant returning to the boiler. This reduces the risk of low temperature corrosion. The valves are manufactured in sizes DN 32-150. Flange connections, body - cast iron, spool - brass, seal - EPDM, T=-10C...110C. Pmax=6 bar |
Model | vendor code | DN, mm | Torque required drive, Nm |
Kvs, m³/h | Weight, kg |
---|---|---|---|---|---|
3F-20 price >> | 11100100 | 20 | 3 | 12 | 3,5 |
3F-25 price >> | 11100200 | 25 | 3 | 18 | 4,0 |
3F-32 price >> | 11100300 | 32 | 5 | 28 | 5,9 |
3F-40 price >> | 11100400 | 40 | 5 | 44 | 6,8 |
3F-50 price >> | 11100600 | 50 | 10 | 60 | 9,1 |
3F-65 price >> | 11100800 | 65 | 10 | 90 | 10,0 |
3F-80 price >> | 11101000 | 80 | 10 | 150 | 16,2 |
3F-100 price >> | 11101200 | 100 | 15 | 225 | 21,0 |
3F-125 price >> | 11101400 | 125 | 15 | 280 | 27,0 |
3F-150 price >> | 11101600 | 150 | 15 | 400 | 37,0 |
4F-50 price >> | 11101900 | 50 | 10 | 60 | 11,0 |
4F-65 price >> | 11102000 | 65 | 10 | 90 | 12,2 |
4F-80 price >> | 11102100 | 80 | 10 | 150 | 20,0 |
4F-100 price >> | 11102200 | 100 | 15 | 225 | 25,0 |
Electric actuators, Esbe ARA 600 actuators for three-way mixing valves.Esbe ARA 600 actuators are designed to automate the control of valves of the VRG, VRB, MG, G, F series< DN50. Выпускаются для 24В и 230 В (частота 50 Гц). Некоторые виды клапанов и приводов сконструированы таким образом, что между ними образуется специальное соединение «клапан – привод», образующее устройство с уникальными характеристиками точности и устойчивости. Диапазон действия приводов составляет от 90°. Разные модели предусматривают разное время закрывания, в среднем от 15 до 240 секунд. Надёжность, экономичность и комфорт в использовании – главные принципы, которыми руководствуются специалисты компании Esbe при разработке сервоприводов Esbe ARA. |
Model | vendor code | Email nutrition | Time closing |
Control | An effort | Replaces |
---|---|---|---|---|---|---|
ARA639 price >> | 12520100 | AC/DC 24V | 15/30/60/120 sec. |
0-10V/4-20mA |
6 Nm |
- |
ARA642 price >> | 12101600 | AC 230V | 30 sec. |
3-point with add. off |
6 Nm | - |
ARA651 price >> | 12101200 | AC 230V | 60 sec. |
3 point | 6 Nm | 65 |
ARA652 price >> | 12101700 | AC 230V | 60 sec. | 3-point with add. off | 6 Nm | 65M |
ARA655 price >> | 12120900 | AC 230V | 60 sec. | 2 point | 6 Nm | 68 |
ARA659 price >> | 12520200 | AC/DC 24V | 45/120 sec. | 0-10V/4-20mA | 6 Nm | 62p |
ARA661 price >> | 12101300 | AC 230V | 120 sec. | 3 point | 6 Nm | 66 |
ARA662 price >> | 12101800 | AC 230V | 120 sec. | 3-point with add. off | 6 Nm | 66M |
ARA663 price >> | 12100300 | AC 24V | 120 sec. | 3 point | 6 Nm | 62 |
ARA664 price >> | 12100800 | AC 24V | 120 sec. | 3-point with add. off | 6 Nm | 62M |
Electric actuators, Esbe series 90 actuators.Esbe series 90 compact reversing actuators are designed to control Esbe control valves of sizes DN 15-150, torque 5-15 Nm. These servo drives are supplied in three versions depending on the type of control signal: 2-point, 3-point or proportional, equipped with limit switches in the extreme positions and have the ability to adjust the operating angle in the range of 30–180°. The Esbe 90 electric actuator allows you to control the valve in manual mode, while the position is displayed on the indicator disk. This series is available with both 24V and 230V power supply and different opening times. Esbe Series 90 actuators work effectively with VRG100, VRG200, VRG300, VRB100, F, MG, G, BIV and H series valves. |
Model | vendor code | Email nutrition | Time closing |
Control | An effort |
---|---|---|---|---|---|
92 price >> | 12050600 | AC 24V | 60 sec. |
3 point | 15 Nm |
92P price >> | 12550100 | AC/DC 24V | 60/90/120 sec. | 0-10V/4-20mA | 15 Nm |
93 price >> | 12051300 | AC 24V | 240 sec. |
3 point | 15 Nm |
94 price >> | 12051700 | AC 230V | 15 sec. | 3 point | 5 Nm |
95 price >> | 12051900 | AC 230V | 60 sec. |
3 point | 15 Nm |
95-2 price >> | 12052000 | AC 230V | 120 sec. |
3 point | 15 Nm |
95M price >> | 12052200 | AC 230V | 60 sec. | 3-point with add. off | 15 Nm |
95-2M price >> | 12052100 | AC 230V | 120 sec. | 3-point with add. off | 15 Nm |
96 price >> | 12052300 | AC 230V | 240 sec. |
3 point | 15 Nm |
97 price >> | 12052500 | AC 230V | 15 sec. |
2 point | 5 Nm |
98 price >> | 12052600 | AC 230V | 60 sec. |
2 point | 15 Nm |
Esbe controllers of the CRB, CRA, 90C, CUA series.Modern Esbe controllers of the CRB, CRA, 90C and CUA series have been designed to provide a higher level of comfort and energy savings. The CRA series includes combined drives and constant temperature controllers with the ability to control the temperature from 5 to 95°C. CRB controllers with built-in actuator and user-friendly interface consist of an actuator and a display with a room temperature sensor, based on which the adjustment is made. ESBE CRB and CRA controllers are used with the following valve series: VRG100, VRG200, VRG300, VRB100, G, BIV, H and HG, F<=DN40, Для клапанов серии F предназначены контроллеры CRA120, CRB 120. |
Model | vendor code | Email nutrition | Time closing |
An effort |
---|---|---|---|---|
CRA111 price >> | 12720100 | AC 230V | 30 sec. |
6 Nm |
CRA121 price >> | 12742100 | AC 230V | 120 sec. | 15 Nm |
CRA122 price >> | 12742200 | AC 24V | 120 sec. | 15 Nm |
CRB111 price >> | 12660100 | AC 230V | 30 sec. | 6 Nm |
CRB114 price >> | 12661400 | AC 230V | 30 sec. | 6 Nm |
CRB122 price >> | 12662200 | AC 230V | 30 sec. | 6 Nm |
CRC111 price >> | 12820100 | AC 230V | 30 sec. | 6 Nm |
CRC121 price >> | 12842100 | AC 230V | 120 sec. | 15 Nm |
CUA111 price >> | 12640100 | AC 230V | 120 sec. | 15 Nm |
CUA122 price >> | 12642200 | AC 230V | 120 sec. | 15 Nm |
90C-1A-90 price >> | 12601500 | AC 230V | 120 sec. | 15 Nm |
90C-1B-90 price >> | 12601600 | AC 230V | 120 sec. | 15 Nm |
90C-1C-90 price >> | 12601700 | AC 230V | 120 sec. | 15 Nm |
90C-3B-90 price >> | 12603600 | AC 230V | 120 sec. | 15 Nm |
90C-3C-90 price >> | 12603700 | AC 230V | 120 sec. | 15 Nm |
Esbe thermostatic mixing valves VTA320, VTA370, VTA570Esbe thermostatic valves of the basic series VTA 320, VTA 370 have a high flow capacity and have increased functionality. Depending on the model, they can be used in domestic hot water and underfloor heating systems. The main functions of these valves are asymmetric flow direction and scald protection. The scalding protection is based on the automatic interruption of the hot water supply when the cold water supply is interrupted. Coupling, valve body - DZR brass, spool - brass, EPDM seal, PN=10, coolant temperature max. 95C. |
Model | vendor code | Accession | Kvs, m³/h | Pace. range, °C | Weight, kg |
---|---|---|---|---|---|
VTA321-15 price >> | 31100300 | Rp 1/2" | 1,5 | 20 - 43 | 0,45 |
VTA321-20 price >> | 31100700 | Rp 3/4" | 1,6 |
20 - 43 | 0,48 |
VTA321-20 price >> | 31100800 | Rp 3/4" | 1,6 |
35 - 60 |
0,48 |
VTA322-25 price >> | 31101000 | G 1" | 1,6 |
35 - 60 | 0,48 |
VTA372-25 price >> | 31200100 | G 1" | 3,4 |
20 - 55 |
0,52 |
VTA572-25 price >> | 31702100 | G 1" | 4,5 |
20 - 55 | 0,86 |
Model | vendor code | DN | Kvs, m³/h | Accession | Weight, kg |
---|---|---|---|---|---|
VLA121-15-1.6 | 21150100 | 15 | 1.6 | Rp 1/2" | 1.0 |
VLA121-15-2.5 price >> | 21150200 | 15 | 2.5 | Rp 1/2" | 1.0 |
VLA121-15-4 price >> | 21150300 | 15 | 4 | Rp 1/2" | 1.0 |
VLA121-20-6.3 price >> | 21150400 | 20 | 6.3 | Rp 3/4" | 1.2 |
VLA121-25-10 price >> | 21150500 | 25 | 10 | Rp 1" | 1.3 |
VLA121-32-16 price >> | 21150600 | 32 | 16 | Rp 1 1/4" | 1.8 |
VLA121-40-25 price >> | 21150700 | 40 | 25 | Rp 1 1/2" | 2.7 |
VLA121-50-38 price >> | 21150800 | 50 | 38 | Rp 2" | 4.2 |
Model | vendor code | DN | Kvs, m³/h | Accession | Weight, kg |
---|---|---|---|---|---|
VLA131-15-1.6 | 21150900 | 15 | 1.6 | Rp 1/2" | 1.1 |
VLA131-15-2.5 | 21151000 | 15 | 2.5 | Rp 1/2" | 1.1 |
VLA131-15-4 price >> | 21151100 | 15 | 4 | Rp 1/2" | 1.1 |
VLA131-20-6.3 price >> | 21151200 | 20 | 6.3 | Rp 3/4" | 1.3 |
VLA131-25-10 price >> | 21151300 | 25 | 10 | Rp 1" | 1.5 |
VLA131-32-16 price >> | 21151400 | 32 | 16 | Rp 1 1/4" | 2.1 |
VLA131-40-25 price >> | 21151500 | 40 | 25 | Rp 1 1/2" | 3.0 |
VLA131-50-38 price >> | 21151600 | 50 | 38 | Rp 2" | 4.7 |
Model | vendor code | DN | Kvs, m³/h | Accession | Weight, kg |
---|---|---|---|---|---|
VLE122-15-0.25 | 21250100 | 15 | 0.25 | G 1" | 1.0 |
VLE122-15-0.4 price >> | 21250200 | 15 | 0.4 | G 1" | 1.0 |
VLE122-15-0.63 price >> | 21250300 | 15 | 0.63 | G 1" | 1.0 |
VLE122-15-1 price >> | 21250400 | 15 | 1 | G 1" | 1.0 |
VLE122-15-1.6 price >> | 21250500 | 15 | 1.6 | G 1" | 1.0 |
VLE122-15-2.5 price >> | 21250600 | 15 | 2.5 | G 1" | 1.0 |
VLE122-15-4 price >> | 21250700 | 15 | 4 | G 1" | 1.0 |
VLE122-20-6.3 price >> | 21250800 | 20 | 6.3 | G 1 1/4" | 1.2 |
VLE122-25-10 price >> | 21250900 | 25 | 10 | G 1 1/2" | 1.4 |
VLE122-32-16 price >> | 21251000 | 32 | 16 | G2" | 1.8 |
VLE122-40-25 price >> | 21251100 | 40 | 25 | G2 1/4" | 2.6 |
VLE122-50-38 price >> | 21251200 | 50 | 38 | G2 3/4" | 4.3 |
Model | vendor code | DN | Kvs, m³/h | Accession | Weight, kg |
---|---|---|---|---|---|
VLE132-15-1.6 | 21251300 | 15 | 1.6 | G 1" | 1.1 |
VLE132-15-2.5 price >> | 21251400 | 15 | 2.5 | G 1" | 1.1 |
VLE132-15-4 price >> | 21251500 | 15 | 4 | G 1" | 1.1 |
VLE132-20-6.3 price >> | 21251600 | 20 | 6.3 | G 1 1/4" | 1.3 |
VLE132-25-10 price >> | 21251700 | 25 | 10 | G 1 1/2" | 1.6 |
VLE132-32-16 price >> | 21251800 | 32 | 16 | G2" | 2.0 |
VLE132-40-25 price >> | 21251900 | 40 | 25 | G2 1/4" | 2.9 |
VLE132-50-38 price >> | 21252000 | 50 | 38 | G2 3/4" | 4.6 |
Model | vendor code | DN | Kvs, m³/h | Stroke, mm | Weight, kg |
---|---|---|---|---|---|
VLA325-15-1.6 price >> | 21200100 | 15 | 1.6 | 20 | 2.1 |
VLA325-15-2.5 price >> | 21200200 | 15 | 2.5 | 20 | 2.1 |
VLA325-15-4 price >> | 21200300 | 15 | 4 | 20 | 2.1 |
VLA325-20-6.3 price >> | 21200400 | 20 | 6.3 | 20 | 2.6 |
VLA325-25-10 price >> | 21200500 | 25 | 10 | 20 | 3.2 |
VLA325-32-16 price >> | 21200600 | 32 | 16 | 20 | 4.6 |
VLA325-40-25 price >> | 21200700 | 40 | 25 | 20 | 5.8 |
VLA325-50-38 price >> | 21200800 | 50 | 38 | 20 | 8.0 |
Model | vendor code | DN | Kvs, m³/h | Stroke, mm | Weight, kg | Replaces |
---|---|---|---|---|---|---|
VLB325-65-63 price >> | 21220100 | 65 | 63 | 25 | 23.0 | VLB225 21203100 |
VLB325-80-100 price >> | 21220200 | 80 | 100 | 45 | 30.0 | VLB225 21203200 |
VLB325-100-130 price >> | 21220300 | 100 | 130 | 45 | 45.6 | VLB225 21203300 |
VLB325-125-200 | 21220400 | 125 | 200 | 45 | 55.0 | VLB225 21203400 |
VLB325-150-300 | 21220500 | 150 | 300 | 45 | 71.0 | VLB225 21203500 |
Model | vendor code | DN | Kvs, m³/h | Stroke, mm | Weight, kg |
---|---|---|---|---|---|
VLA335-15-1.6 | 21200900 | 15 | 1.6 | 20 | 2,5 |
VLA335-15-2.5 price >> | 21201000 | 15 | 2.5 | 20 | 2,5 |
VLA335-15-4 price >> | 21201100 | 15 | 4 | 20 | 2,5 |
VLA335-20-6.3 price >> | 21201200 | 20 | 6.3 | 20 | 3,2 |
VLA335-25-10 price >> | 21201300 | 25 | 10 | 20 | 3,8 |
VLA335-32-16 price >> | 21201400 | 32 | 16 | 20 | 6,6 |
VLA335-40-25 price >> | 21201500 | 40 | 25 | 20 | 7,5 |
VLA335-50-38 price >> | 21201600 | 50 | 38 | 20 | 10 |
Model | vendor code | DN | Kvs, m³/h | Stroke, mm | Weight, kg | Replaces |
---|---|---|---|---|---|---|
VLB335-65-63 price >> | 21221100 | 65 | 63 | 25 | 19.0 | VLB235 21203600 |
VLB335-80-100 price >> | 21221200 | 80 | 100 | 45 | 24.0 | VLB235 21203700 |
VLB335-100-130 price >> | 21221300 | 100 | 130 | 45 | 32.0 | VLB235 21203800 |
VLB335-125-200 | 21221400 | 125 | 200 | 45 | 46.0 | VLB235 21203900 |
VLB335-150-300 | 21221500 | 150 | 300 | 45 | 61.0 | VLB235 21204000 |
ESBE VLC125 seated control valvesESBE VLC125 2-way flanged control valves are used to control the flow of heating medium. The valves are made of ductile iron, which allows their use in heating and cooling systems with pressures up to 25 bar. The VLC125 series has flanged connections and is available in sizes DN15-DN50. The valves are designed for automatic operation in combination with ESBE actuators. | |||||
VLC125-40-16 | 21302600 | 40 | 16 | 20 | 7.7 |
VLC125-40-25 price >> | 21301100 | 40 | 25 | 20 | 8.8 |
VLC125-50-38 price >> | 21301200 | 50 | 38 | 20 | 12.6 |
Electric actuators for ESBE poppet control valvesLinear actuator series ESBE in 230 V or 24 V version, with analog or pulse control. The actuators have different forces and are adapted to valves with different strokes. A separate line of actuators with a return spring is also presented. Depending on the model, valves equipped with such actuators can be normally closed or normally open. ALD121 22150500AC/DC 24V |
2200 |
20 sec. | ALD144 22151200 | |||
ALH134 price >> | 22220100 | 3-position/0...10 V | AC/DC 24V | 900 |
15 sec. |
- |
ALH234 price >> | 22221100 | 3-position/0...10 V | AC/DC 24V | 900 |
15 sec. | - |
Three way mixing valve has a fairly simple device. It consists of a housing with two inlets and one outlet, as well as a specially shaped stem, on which a handle (for manual control) or an electric drive (for automatic flow temperature control) is installed. The rod is able to rotate along the vertical axis, blocking to some extent the inlet of hot or cold water, due to which a certain ratio of flows is created and, as a result, a mixture of a given temperature is obtained at the outlet. The body material of a three-way valve is most often brass alloy or cast iron. The stem is made of brass, cast iron or stainless steel.
Three way valve control is carried out with the help of an electric drive installed on the rod, which is supplied separately. The main characteristics of electric actuators are: the time of rotation of the rod by 90 degrees; the force with which the actuator is able to rotate the stem; electrical voltage and control signal (two-point, three-point, proportional). The electric drive receives a signal from the common house controller, which, based on the readings of various temperature sensors, calculates the position of the three-way valve stem to obtain the desired temperature of the coolant at the outlet.
Selecting an actuator for a rotary three-way mixing valve. For sleeve mixing valves ESBE actuators of the ARA600 series are used, for flanged cast iron valves the ESBE 90 series is used. If as a mixer, then 3-point control or proportional control is necessary: 0-10V signal. Next, select the desired combination of stem rotation time and valve assignment. 60 seconds will be enough for domestic hot water supply, and for supplying coolant to radiators, most often, electric drives with a stem rotation time of 120 seconds are used. If it is necessary to control external equipment depending on the position of the valve (for example, turn off an unnecessary pump, etc.), we determine whether an auxiliary switch is needed. When all the technical characteristics of the electric drive are determined, it will not be difficult to choose from the presented models exactly the one that will perform all the specified functions.
Esbe valves are one of the most reliable and functional components used in various water supply systems, including domestic and main ones. It has a very wide range, which includes: rotary vrg131, dn25, as well as other popular varieties.
Currently, a three-way rotary sample of such equipment can be installed in every home. In order to do it right, let's look at the intricacies of working with such equipment and the features of its use.
Article content
Esbe valves are a variety of devices used to control a liquid or gas when it is supplied from one pipe to another. The three-way type of valves is distinguished by the presence of three connections that allow you to effectively redirect the flows in the system, especially in the case of mixing hot and cold water.
Adjusting the operation of valves of this type within the same system can realize the servo. This device needs a little more attention.
Servo. This is a separate element in the system that controls the position of the valves. A servo drive is usually the most affordable and easy to install, which is why it is most often used for.
According to the design features, the servo drive can be different, most often they are included in the category of such devices. For example, this can be installed with vrg131 samples. Today they provide the highest quality and accuracy in system maintenance, which is why they are so popular among consumers.
In some devices, a servo drive, as well as motor control is not used. In such cases, such special devices are used as for adjusting the operation of the equipment.
Such varieties include, for example, a dn25 valve, which can be mounted in a crane without a drive.
This type of product can be used in a wide range of systems, including heating systems, even centralized, hot, cold water supply, as well as air conditioning.
These types of valves are suitable for various systems, including those operating on oil products, gas, as well as eco-fuels, including solar energy or wind energy. It is possible to install these types of equipment, for example, a three-way rotary valve vrg131, both for central water supply networks and for home networks.
You can pick up a product for any crane. It is only important to choose the right type of product and install it according to the recommendations. Also, for the system to work properly, it is very important to adjust the servomotor or thermostatic controller.
Then the model chosen by you will work without failures, irrespective of the set technical parameters.
Among the main advantages of installing exactly Esbe products are:
Currently, the following Esbe valve models are especially popular on sale:
Esbe products are quite popular today. is no exception. It is one of the many elements that are included in the life support system of residential buildings.
This design, on the one hand, is quite simple, but on the other hand, it is designed to perform an extremely important task, being part of engineering networks. Everyone knows the rule that demand creates supply, which is why on the market today you can find many models that are represented by various manufacturers. However, valves manufactured by Esbe are distinguished by excellent performance. A three-way valve of this type can be purchased at an affordable cost. This is confirmed by user reviews.
In a wide range today you can find Esbe products. The three-way valve is no exception. This element has a regulating component, which is a ball or a rod. The latter moves vertically, but as for the ball, its movement occurs around its axis. Due to the fact that the movements of the regulating element do not allow to block the flow of liquid, distribution and mixing occurs. The most common and simple models are cranes.
Their main advantage is low cost and simplicity. However, if you need to adjust the Esbe three-way valve, then you should exclude the purchase of simple devices, since they have the main drawback, expressed in the inability to stabilize the outlet temperature.
Almost all described valves that are on the market are connected on the basis of one scheme. Most often, mixer taps are used in water supply systems. Their main goal is to reduce the risk of backflow. Between the streams of cold and hot water, a pressure difference will inevitably occur. It can cause reverse flow. If you install a valve, then you will not encounter such a problem. If we are talking about a heating system, then such devices are used exclusively in three directions, namely, to stabilize the temperature regime of the coolant flow in the incoming pipeline of boiler equipment, to reduce the supply of high-temperature water from the heating device to the pipeline, as well as in the conditions of mixing units of systems underfloor heating.
If you are interested in Esbe products, the three-way valve can be purchased from any relevant store. One has only to consider before that how the tap is used in the underfloor heating system. The use of a mixing unit allows you to create an additional circuit in the system. It connects with two points to this allows for a constant circulation of water at the outlet. As for the inlet, the flow is provided only if there is a need to obtain additional heat. The thermostatic valve is connected to the mixing unit. Due to the fact that all valves are at the point, they are narrowed, which can cause insufficient flow of pumping equipment. To increase it, it is necessary to create an additional line, with which you can reduce the electricity consumption of the pump. During the installation process, it is worth remembering that a second line is not always required. A number of valve models have a fairly large passage. An Esbe three-way valve, whose connection diagram can be designed based on the instructions presented in the article, may suggest insufficient flow capacity in the first line. In this case, the thermostat is not able to open the passage of the required size. This issue can be easily solved in two ways: the first involves narrowing the second line, while the other option is to mount on it. The latter option is considered more productive, as it allows you to adjust the flow.
Installation of the Esbe three-way valve can also be done by another method. It does not involve the use of a balancing crane. The pump is connected to the second line, eventually the temperature of the outlet and inlet streams equalize. A thermostatic valve is found in single circuit systems. The simplest example of such systems is underfloor heating in small rooms. In this case, it is not always justified to create a mixing unit with large dimensions. It is best to connect the underfloor heating system using one circuit. If you are thinking about how to connect an Esbe three-way valve with an electric drive, then it can be placed on the return line, through which cooled water runs. In this case, the thermostat will lead to the movement of the valves, the cross section will be increased, and the flow will be open. As soon as the pipe is heated, the thermal sensor will detect this and reduce the flow.
This issue, according to professionals, must be considered separately. The main task of the installation is to prevent the entry of a cold water flow to the incoming pipeline, which is connected to the heating equipment. If this requirement is not taken into account, then condensation will occur on the pipes, temperature drops will lead to deformation at the joints. If we talk about the consequences of deformation, then at best you will encounter a small leak, while at worst the system will need to be completely changed. In order to avoid the need to repair the Esbe three-way valve, it is important to connect the shut-off valves to the boiler, which is characterized by temperature changes during operation. If you install a mixing valve, then you can ensure that water does not enter the inlet of the equipment, the temperature of which is below 50 degrees. The temperature difference is significantly reduced, the negative impact of cold is reduced. Experts advise supplementing systems that are equipped with plastic pipelines with mixing valves. In this case, the task is to prevent the ingress of high temperature water into the pipeline. While polymers have many advantages, they do not do well with frequent temperature changes, which can be higher than operating temperatures.
Under the influence of such conditions, the pipeline system fails soon enough. Experts advise choosing Esbe products. The three-way valve, the installation instructions for which are presented in the article, has been manufactured by this company for a long time. If you use this element, then you can provide temperature readings ranging from 75 to 85 degrees, which are recommended by experts. Mounting the valve allows you to cope with many problems, however, the model must be selected in accordance with the characteristics of the network, and also have a sufficiently large passage.
When purchasing Esbe products - a three-way valve, the installation and adjustment instructions for which are presented in the article - you must remember that with this device it is possible to mix the cooled water from the return into the supply. For high-quality regulation, not only a three-way valve, but also a four-way valve, which must be present in the heating system, is installed in the system independently. It is located directly in front of the contour of the warm floor. The handle allows you to open the bypass, while the circulation pumps and equipment draw in the cooled coolant from the return, where it is mixed with hot water. In order for the adjustment to be made as efficiently as possible, you should understand what happens at certain positions of the handle. The latter can be set to the bypass overlap position, while the hot coolant will flow into the pipe of the underfloor heating system. As for the mode in which the supply is blocked, water enters the tank and runs in a small circle. The third position allows you to feed the supply from the return system without blocking the full cycle of water passage throughout the circuit.
Recently, experts have increasingly recommended purchasing Esbe brand products. A three-way valve, the instruction, the wiring diagram of which is presented in the article, is just an example of this. It can act as an indispensable element of the heating system and part of the boiler equipment, however, it is important to choose the right model and install it, observing the technology.
A three-way valve in a water supply or heating system is responsible for mixing or separating liquids of different temperatures, as well as for obtaining the required temperature at the outlet of the liquid (adjusting the temperature of the coolant using a servo drive).
The body of the device contains two inlets and one outlet for liquids and a control element, which can be of different designs (for example, a rotary ball or a travel rod), as well as a place for a servo drive.
Usually, the valve is not designed to completely shut off the liquid outlet, but is only capable of controlling the mixing ratio of the liquids and the temperature in the system. The instruction does not imply, but functionally, it is quite possible to shut off the liquid supply.
A three-way valve of a certain variety, which performs a dividing function, may have a rotary servo to redirect the flow to different pipes (then it is called "shut-off").
In this case, there is no gradual or smooth mixing of fluids with temperature control, and the rotary mechanism itself consists of a ball (like a Bugatti ball valve).
There are several varieties of it, according to the type of drive mechanism, performing the same functions:
Yes, three Esbe's new valve, having a servo drive, will assume the actual sample itself and a compatible drive manufactured by the same company.
Esbe has been in business for over 100 years and specializes in temperature control for hydraulic systems in small buildings.
It manufactures a valve and a rotary actuator for cooling or heating systems, also working "in conjunction" with indoor and outdoor temperature sensors in the system. The principle of operation of the Esbe three-way valve is similar to the above options.
The company produces several model series of three-way valves, including a mixing valve:
Valves of the VRG130 series are applied to systems of hot/cold water supply. This model range, like the subsequent ones, has various options (for example, the three-way valve from Esbe VRG 131 also belongs to this series and has a connection for a servo drive).
They are compact mixing models made of brass alloys, designed to minimize leakage and with a manual adjustment dial. The instruction indicates that they are also compatible with Esbe automatic control systems and controllers, which allow automating the operation of valves.
Esbe three-way valve of this model series - available in sizes DN 15-50, pressure class - PN 10, model options include varieties with internal (three-way mixing valve type Esbe model VRG131 with connection for actuator), external thread
(model VRG132), with union nut or compression fittings.three-way Esbe's VRG330 Series Mixing Valve has similar features to the previously described VRG131 Series (DN 20-50, PN 10), but is specifically designed for high flows (60 percent kvs difference between inlets).
It can also be equipped with compatible controllers and automatic control. Available with three types of connection: internal thread, external thread, rotating nut.
According to Esbe specification, 3F series rotary mixing valves are designed for heating and cooling applications.
Esbe controllers and automatic control systems can also be used with them.
For ease of installation, the Esbe 3F three-way valve is marked with an adjustment scale on both sides. The valve body is made of cast iron, the model is also supplied with an adapter for a flanged pipe PN 6, model sizes - DN25-150.
The mixing valve from Esbe series H (DN25-40) and HG (DN25) is designed for installation in confined spaces.
This three-way control valve from Esbe is used only for heating systems and is specified for operation with a boiler group (made of cast iron, special "H"-shaped body). It also has an acceptable price.
As the main type of connection, both internal thread and its mixed type are used. Compatible with Esbe controllers and actuators like VRG131 .
Models of the VRH130 series are also made in the "H"-shaped version, but made of brass with a pressure class of PN 10. This model is more versatile than the previous sample and can also be used in water supply systems, is available with different body widths.
The VLF300 series is a 3-way mixing line with sizes DN 15-50.
This model range is It is made of nodular cast iron and can be used with working fluids such as cold/hot water, and which contain antifreeze components (glycol, for example).
In the latter case, the sample must be equipped with a rod heater. It is completed with a flange for a PN 6 pipe. Models similar to those previously indicated, VLF200 dn25, are distinguished by a high working pressure of up to 16 bar (against 6 bar for the previously indicated model range).
Models VLE132 - made of bronze with sizes DN 15-50. These are linear motorized valves, which, like the previously mentioned similar models, can use water with glycol as working fluids (connection - external thread PN16), unlike the VRG131 series. Its price ranges from 140 to 350 euros.
All listed 3-way in-line valves are compatible with the Esbe controller and actuator.
VTS520 / 550 - the instruction indicates that the three-way valves are designed to work with hot water systems that are connected to a solar heating system. Its price starts from 150 euros.
A feature of this model range is that the Esbe three-way thermostatic valve comes with specialized protection against burns, since the liquid circulating in the system is of a sufficiently high temperature.
Esbe's three-way thermostatic mixing valve with "scald protection" features a sensor that automatically turns off the hot water servo if cold water is not supplied.
The coolant with which these models work is water (including drinking water), the coolant of closed systems is water with non-freezing components. Pressure class - PN 10, the body is made of brass, resistant to corrosion, for example, the VRG131 valve is not suitable for such a system.
VTA330/530 is Esbe's thermostatic mixing valve of this series designed for use in domestic hot water systems, as well as in faucets or showers where no other means of temperature control is provided (VTA330), or in domestic hot water systems with high flow (VTA530). Its price is within 150 euros.
Also equipped with a security system you from burns. Pressure class PN 10 (material - brass, resistant to corrosion), is available with external threaded connection, fittings or adapters.
VTA360 / 560 - a series similar to the previous one in execution, but equipped with a large number of fittings and connections. The instruction assumes that the drive of the Esbe three-way device of this series must also be compatible with those specified by the company in the specification.
Representatives of the VTA320/520 series can be used both in conditions similar to the operating modes of the previous model ranges, and in systems where other temperature control systems are present.
These valves are recommended for hot water circulation systems (HWC) or floor heating systems. Also equipped with "burn protection". VTA370 / 570 - models designed for use in the "warm floor" system, have a high throughput.
VTA310 - sample supplied with adjusting knob, without burn protection system. It is used in domestic water supply systems, including - in the closed cycle hot water supply system (HWC). The price for it starts from 50 euros.
When installing a three-way mixing valve, various options, instructions and algorithms are selected for installation. As a rule, the part is not installed directly to the heat source, since the system uses a non-pressure manifold or "hydraulic arrow".
In the version for heating, the simplified instruction assumes that the coolant is supplied from the boiler to the valve, from there the coolant is supplied to the heating system through the pump.
The liquid that has passed through the heating system and cooled down is sent to the boiler for heating, but also to the mixing valve, which ensures the temperature control of the supplied substance.
The instruction for the Esbe three-way valve usually involves a description of the connection of the valve to the system, which, depending on the model range, may be different.
The cw602n Esbe three-way valve (here the brand of brass is indicated) of the VRG130 model range (namely, VRG131 ½) costs an average of $ 170 (if purchased complete with an actuator).
The price of a three-way valve from Esbe linear VLA330, depending on the configuration, is $ 150 (not equipped with an electric actuator).
The Esbe three-way thermostatic valve (VTA 320) can be priced at $70 or more.
Esbe products are quite popular today. is no exception. It is one of the many elements that are included in residential buildings.
This design, on the one hand, is quite simple, but on the other hand, it is designed to perform an extremely important task, being part of engineering networks. Everyone knows the rule that demand creates supply, which is why on the market today you can find many models that are represented by various manufacturers. However, valves manufactured by Esbe are distinguished by excellent performance. A three-way valve of this type can be purchased at an affordable cost. This is confirmed by user reviews.
In a wide range today you can find Esbe products. The three-way valve is no exception. This element has a regulating component, which is a ball or a rod. The latter moves vertically, but as for the ball, its movement occurs around its axis. Due to the fact that the movements of the regulating element do not allow to block the flow of liquid, distribution and mixing occurs. The most common and simple models are cranes.
Their main advantage is low cost and simplicity. However, if you need to adjust the Esbe three-way valve, then you should exclude the purchase of simple devices, since they have the main drawback, expressed in the inability to stabilize the outlet temperature.
Almost all described valves that are on the market are connected on the basis of one scheme. Most often, mixer taps are used in water supply systems. Their main goal is to reduce the risk of backflow. Between the streams of cold and hot water, a pressure difference will inevitably occur. It can cause reverse flow. If you install a valve, then you will not encounter such a problem. If we are talking about a heating system, then such devices are used exclusively in three directions, namely, to stabilize the temperature regime of the coolant flow in the incoming pipeline of boiler equipment, to reduce the supply of high-temperature water from the heating device to the pipeline, as well as in the conditions of mixing units of systems underfloor heating.
If you are interested in Esbe products, the three-way valve can be purchased from any relevant store. One has only to consider before that how the tap is used in the underfloor heating system. Application allows you to create an additional circuit in the system. It connects with two points to this allows for a constant circulation of water at the outlet. As for the inlet, the flow is provided only if there is a need to obtain additional heat. The thermostatic valve is connected to the mixing unit. Due to the fact that all valves are at the point, they are narrowed, which can cause insufficient flow of pumping equipment. To increase it, it is necessary to create an additional line, with which you can reduce the electricity consumption of the pump. During the installation process, it is worth remembering that a second line is not always required. A number of valve models have a fairly large passage. An Esbe three-way valve, whose connection diagram can be designed based on the instructions presented in the article, may suggest insufficient flow capacity in the first line. In this case, the thermostat is not able to open the passage of the required size. This issue can be easily solved in two ways: the first involves narrowing the second line, while the other option is to mount on it. The latter option is considered more productive, as it allows you to adjust the flow.
Installation of the Esbe three-way valve can also be done by another method. It does not involve the use of a balancing crane. The pump is connected to the second line, eventually the temperature of the outlet and inlet streams equalize. A thermostatic valve is found in single circuit systems. The simplest example of such systems is underfloor heating in small rooms. In this case, it is not always justified to create a mixing unit with large dimensions. It is best to connect the underfloor heating system using one circuit. If you are thinking about how to connect an Esbe three-way valve with an electric drive, then it can be placed on the return line, through which cooled water runs. In this case, the thermostat will lead to the movement of the valves, the cross section will be increased, and the flow will be open. As soon as the pipe is heated, the thermal sensor will detect this and reduce the flow.
This issue, according to professionals, must be considered separately. The main task of the installation is to prevent the entry of a cold water flow to the incoming pipeline, which is connected to the heating equipment. If this requirement is not taken into account, then condensation will occur on the pipes, temperature drops will lead to deformation at the joints. If we talk about the consequences of deformation, then at best you will encounter a small leak, while at worst the system will need to be completely changed. In order to avoid the need to repair the Esbe three-way valve, it is important to connect the shut-off valves to the boiler, which is characterized by temperature changes during operation. If you install a mixing valve, then you can ensure that water does not enter the inlet of the equipment, the temperature of which is below 50 degrees. The temperature difference is significantly reduced, the negative impact of cold is reduced. Experts advise supplementing systems that are equipped with plastic pipelines with mixing valves. In this case, the task is to prevent the ingress of high temperature water into the pipeline. While polymers have many advantages, they do not do well with frequent temperature changes, which can be higher than operating temperatures.
Under the influence of such conditions, the pipeline system fails soon enough. Experts advise choosing Esbe products. The three-way valve, the installation instructions for which are presented in the article, has been manufactured by this company for a long time. If you use this element, then you can provide temperature readings ranging from 75 to 85 degrees, which are recommended by experts. Mounting the valve allows you to cope with many problems, however, the model must be selected in accordance with the characteristics of the network, and also have a sufficiently large passage.
When purchasing Esbe products - a three-way valve, the installation and adjustment instructions for which are presented in the article - you must remember that with this device it is possible to mix the cooled water from the return into the supply. For high-quality regulation, not only a three-way valve is installed in the system, but also a four-way valve, which must be present in the heating system. It is located directly in front of the contour of the warm floor. The handle allows you to open the bypass, while the circulation pumps and equipment draw in the cooled coolant from the return, where it is mixed with hot water. In order for the adjustment to be made as efficiently as possible, you should understand what happens at certain positions of the handle. The latter can be set to the bypass overlap position, while the hot coolant will flow into the pipe of the underfloor heating system. As for the mode in which the supply is blocked, water enters the tank and runs in a small circle. The third position allows you to feed the supply from the return system without blocking the full cycle of water passage throughout the circuit.
Recently, experts have increasingly recommended purchasing Esbe brand products. A three-way valve, the instruction, the wiring diagram of which is presented in the article, is just an example of this. It can act as an indispensable element of the heating system and part of the boiler equipment, however, it is important to choose the right model and install it, observing the technology.
Despite the simple design, the esbe three-way valve is one of those elements on which the life support of the whole house directly depends. Devices of this type are commercially available in several varieties.
A three-way valve is a device for adjusting pipeline networks with a liquid working medium. If you explain popularly, after being included in the heating system, the device will perform the function of a well-known mixer tap, the task of which is to switch or mix flows.
Thanks to the esbe three-way valve, the following results are achieved:
The adjustment of the three-way valve is carried out using a stem or ball. In the first case, the adjusting element moves in the vertical direction, in the second - around its axis. This element moves in such a way that a complete blockage of the flow of the working fluid does not occur: it only mixes and redirects. The simplest example of such a device is a conventional crane. Its strong point is its simple design and low cost; weak - the impossibility of obtaining a stable outlet temperature. For all their shortcomings, taps are widely used in underfloor heating systems.
If an electric drive is introduced into the design of a conventional crane, then it will be possible to significantly increase its functionality: the device will be able to regulate the temperature of the liquid medium in automatic mode. The task of simple balancing valves is to adjust the section for the flow of the working flow.
The device works like this:
For commercially available models, the turns of the handles may differ slightly, which in no way affects the principle of operation of the devices.
Three-way valves are of three types:
Motorized appliances (eg model ESBE) differ slightly in their principle of operation. An electric appendage acts here like a conventional thermostat: thanks to it, the flows are not only mixed, but also kept at the desired temperature. During a decrease or increase in temperature, the position of the shut-off valves is automatically changed. As a result, the flow cross section increases or decreases. In parallel, there is a change in the cross section at the inlet of the cold flow, which makes it possible to inform the water at the outlet of a stable temperature. At the same time, the three-way esbe valve completely dispenses with human control: the equipment is controlled by automation.
The ESBE valve with electric actuator and thermostat can be successfully used in heating systems and in hot water supply. Strictly speaking, such a valve can be equipped with any type of pipeline, where it is required to mix two liquid streams and maintain a stable temperature. Even the most high-quality and reliable models of a three-way valve with a thermostat have one common drawback for products of this type: the entry points through which fluid enters are very narrowed. As a consequence, this provokes an increase in hydraulic resistance.
These faucets are great for plumbing. ESBE valves are often equipped with underfloor heating, although they use a special connection scheme. Along with the modifications mentioned above, three-way thermostatic valves can be found on sale. Despite the apparent similarity of these devices, their functions differ in many ways. In thermostatic varieties, thermostats with a remote type sensor are used. In addition, the principle of operation here is also different.
Unlike standard models, thermostatic taps control the flow at only one point. The other two inputs are in a permanently open position, with a stable section. When purchasing such a design, it is important to test the second point for narrowness, otherwise the device may experience difficulties due to high hydraulic resistance. If such a defect is found, the problem can be solved by installing a mixing valve in an additional circuit.
For the vast majority of commercially available three-way devices, one connection scheme is used. For example, consider installing an esbe three-way valve. It's best to start with the plumbing system, where mixing taps are most common. Valves in this case prevent the formation of backflow. The fact is that cold and hot streams have different pressures, which provokes drops. As a result, reverse flow may occur. Systems with ESBE valves are completely safe in this respect.
In heating systems, only three sections can be equipped with devices of this type:
The use of the esbe valve for underfloor heating has its own specifics. The location of the mixing unit is an additional circuit. Switching with the manifold is carried out through two points: this allows the inlet coolant to constantly circulate. The inlet flow is opened only when there is a need for additional heat.
The mixing unit is commutated with a valve and a thermostat. You need to understand that a thermostat for a water-heated floor allows you to reduce heating costs. Given the narrowness of all valves at point 2, the pump may be faced with the problem of insufficient flow. To solve the problem, it is necessary to live the second line, which reduces the level of electricity consumption. But such a need does not always arise, because. the cross section of some three-way valves is quite large.
In a situation where the first line has insufficient flow capacity, the thermostat does not block the passage on the required scale.
To get out of this situation, two options are usually used:
The second method is considered more effective, because. the flow in this case is tuned more precisely. There is another scheme for connecting the esbe three-way valve for underfloor heating - switching the pump to the second line: a balancing valve is not needed here. This allows you to equalize the temperature regime in the inlet and outlet streams.
Installation of a valve with a thermostat can be carried out in single-circuit systems. Their simplest variation is a warm floor of a small area. In this case, the overall mixing unit is not very practical to use. A more appropriate solution would be to connect a single-circuit underfloor heating. The installation of a three-way valve with a thermostat is carried out on a return pipe containing a cooled coolant. Thanks to the thermostat, the shut-off valve is activated, which increases the cross section. When the pipe heats up, the temperature sensor detects this and reduces the flow.
Three-way valves for heating boilers deserve special attention. They perform the task of preventing the cooled coolant from getting inside the pipeline entering the boiler. If this is not done, the pipes will begin to become covered with condensate, and a dangerous temperature difference will occur in the system. This is fraught with deformations of the docking sections, the most harmless consequence of which will be the appearance of small leaks. If you do not respond in time, the system may completely fail.
With special responsibility, one should take the installation of shut-off valves in the piping of a solid fuel boiler, during which significant temperature differences occur (read also: ""). The mixing valve allows you to protect boiler equipment from the ingress of coolant with a temperature below +50 degrees. In this way, a reduction in the temperature difference is achieved, which has a positive effect on the efficiency and durability of the system.
Experts recommend using mixing valves also in systems with plastic piping. Although polymer communications have a number of advantages, however, the frequent excess of operating temperature parameters affects them destructively. According to the standards, the most comfortable temperature regime is in the range of + 75-85 degrees. Valves protect plastic pipes from many negative consequences. The selection of a device model must be taken responsibly, taking into account the technical characteristics of the engineering network.
kayabaparts.ru - Entrance hall, kitchen, living room. Garden. Chairs. Bedroom