Topas septic tank: the principle of operation of the cleaning system. The principle of operation and installation of a topas septic tank with your own hands Installation of a topas septic tank in a private house

Self-installation of Topas-type septic tanks should begin with the selection and preparation of the site. Firstly, it is necessary to take into account the minimum distance between its body and the building, which is 5 m. Secondly, with the help of industry standards (SNiP) or design organizations, such a criterion as the depth of soil freezing in a given region is clarified. It affects the choice of the main or extended (Long) version of the septic tank.

After determining the location, you can proceed to the next stage of preparation - the formation of the foundation pit. Its dimensions depend on the dimensions of the septic tank and are determined by the wiring diagram that comes with the kit (example in the illustration below).

A wooden formwork is installed around the perimeter of the pit. This is a necessary precaution to keep the walls from collapsing. When groundwater occurs too close to the surface (the so-called quicksand), without a dense crate of the walls, it is not at all possible to form a foundation pit.

1. With high shrinkage and mobility, sand provides a dynamic, shock-absorbing base. That is, any movement of the soil will be leveled, and the septic tank will retain the correct spatial position and geometry;
2. A layer of 15 cm will raise the top cover to a similar height above the ground. Such a solution will prevent the flooding of the septic tank with melt water and, as a result, the failure of electrified units.

After that, you can proceed to the direct installation of the septic tank in the pit. For the convenience of the operation, there are technological holes in the individual elements of the body (stiffening ribs, for example). You need to thread a safety rope through them and slowly lower the module to the bottom.

This can be done manually, involving assistants, or using auxiliary equipment.

As soon as the septic tank is installed in the pit, it is leveled and the laying and connection of engineering networks begin. Usually, a specialized polyethylene sewer pipe with a diameter of 50 to 110 mm is used for these purposes. In a trench, it is also recommended to lay it on a sand cushion in order to avoid the influence of soil movement. It will be necessary to ensure a sufficient slope, which depends on the diameter of the line: for pipes Ø50 mm - at least 3 cm / m, and for Ø110 mm - at least 1-2 cm / m.

The place of insertion (input) into the body of the septic tank is determined based on the installation conditions and the requirements of the attached scheme. For its formation, it is desirable to use a special core drill with an adjustable diameter. The branch pipe for connection with the pipe is sealed with a special polypropylene soldering cord. It is laid around the perimeter of the hole and processed with a building hair dryer (it melts, and then cools and hardens).

Attention! Once again, I would like to focus on the need to align the body of the septic tank before sealing the joint, since after that it will be almost impossible to do this.

After connecting to the sewer, you can proceed to the electrical connections. For this, a PVC wire with a cross section of 3 × 1.5 mm is used, which is laid in a trench next to the pipe in a corrugated box. On the house shield, the input is carried out through a separate circuit breaker (6-16A). Connections in the terminal box of the septic tank are carried out in accordance with the attached diagram.

At the final stage of installation, it is necessary to fill the space between the walls of the septic tank body and the formwork. This should be done carefully and slowly, adhering to the following recommendations:

• It is desirable to use sand for backfilling for the same reason as in the case of a pillow under a septic tank and. The soil is harder and harder, which in the future may lead to deformation of the walls of the case and disruption of the normal operation of the unit;
• You need to fill up the space gradually, in layers of 15-20 cm, while filling the septic tank with water slightly above the sand level. Thus, it will be possible to equalize the pressure on the walls of the case and avoid their deformation.

Conclusion

On this, the installation of the Topas septic tank can be considered completed. It remains only to ennoble the site and follow the manufacturer's further recommendations regarding operation. There are not so many of them that it could complicate the life of the owner. Most of all, you will have to tinker with coarse filters (located between the receiving chamber and the air tank) - once a month they need to be audited. Every 2-3 years of operation, an audit, cleaning and, if necessary, replacement of compressor membranes is carried out. Approximately once every 3-4 years it is recommended to clean the waste sludge. By the way, it can be used as a fertilizer for the soil in the presence of a household plot. No more than 1 time in 12-15 years, you will have to change the aeration unit.

On the technical side, these are, in principle, all warnings, and as for sewage, it is not recommended to drain wastes with a high content of aggressive detergents, antibiotics and large fractions into it. Subject to these simple conditions, a deep cleaning station of the Topas type can easily serve its allotted 50 years or more.

The arrangement of water supply and sewerage systems on the site is one of the most responsible and complex issues faced by the owners of private houses and summer cottages.

Many homeowners are moving away from the traditional ways of disposing and treating sewage in favor of modern, more efficient and reliable cleaning methods. One of these methods is the use of the Topas septic tank installation. Consider the device, the principle of operation of the cleaning system, the installation procedure and the basic rules for operating the Topas septic tank.

Topas septic tank device

Topas septic tank is an autonomous sewage system that purifies wastewater by 98%. Recycled water is not suitable for drinking, but it is absolutely safe for the environment and does not have an unpleasant odor.

The device of a local treatment plant is quite simple, and the operation of a septic tank is based on biological processes that occur in several stages.

Due to the clear structure of the internal device of an autonomous sewage system, a well-functioning cyclic operation of the septic tank occurs

The following equipment components are involved in the cleaning process:

1. Station cover with air intake.
2. Receiving chamber - wastewater with the highest degree of pollution enters it. Primary water treatment is 45-50%.
3. Aerotank is a chamber in which water is purified by another 20-30%.
4. Airlift with pumping units - provides water transfer between the chambers.
5. Air compressors pump air to support biological processes.
6. The third chamber (usually pyramidal) is for water purification and sludge settling.
7. Cleaning chamber.
8. Device for collecting non-recyclable particles.
9. Silt suction hose.
10. Purified water outlet.

Septic tank Topas: the principle of operation of the cleaning system

The Topas septic tank copes with any sewage of household origin. At the outlet, industrial water and sludge are formed, which can later be used as a fertilizer for a garden plot.

Such purification can be achieved through the use of activated sludge containing dozens of bacteria. The cleaning system involves aerobic (life activity occurs only in the presence of oxygen) and anaerobic (can do without oxygen) bacteria.

The entire cycle of operation of the Topas septic tank can be divided into the following stages:

1. Drains enter and accumulate in the receiving chamber.
2. When the level of effluents reaches the limit mark, the float is activated and the compressor is turned on.
3. Air enters the chamber - anaerobic bacteria enter the process.
4. Large fractions of wastewater break up into small particles.
5. Mixed effluents are fed into the aeration tank.
6. Effluent is recycled by aerobic bacteria.
7. Half of the purified water enters the secondary sump. There is a division into silt and water.
8. Effluent is processed by anaerobic bacteria.
9. The sludge enters the stabilization chamber, and the water exits.
10. In the stabilizer chamber, the sludge is divided into fractions. Light fractions are pumped back to the receiver and participate in biological cleaning, while heavy fractions settle to the bottom.

The filter sludge accumulated in the sump must be periodically removed to prevent overflow of the tank and failure of the entire sewer installation

Advantages and disadvantages of autonomous sewage septic tank Topas

The Topas septic tank appeared on the market of treatment facilities 20 years ago, has established itself well in Europe, and in recent years has gained popularity among consumers in post-Soviet countries.

The demand for a treatment plant is explained by its advantages:

Septic Topas: reviews

Among the disadvantages of the Topas septic tank are:

• the high cost of the cleaning system (you can buy a Topas septic tank for no less than 80 thousand rubles);
• energy dependence of the station;
• neglecting the rules for the maintenance and operation of a septic tank can lead to serious damage and costly repairs to the device.

Choosing a septic tank Topas: types and their technical characteristics

The range of Topas septic tanks includes installations for country use, private houses, gas stations (Topas 5-20) and stations designed for wastewater treatment of a small cottage village (Topas 100-150).

The numerical designation in the product name indicates the number of conditional consumers - this is the main criterion for choosing a Topas septic tank

To give the best option would be to install a Topas-5 septic tank - a cleaning system of low productivity. Such an autonomous sewage system will fully satisfy the needs of a family of no more than 5 people.

Specifications Topas-5:

• the maximum allowable volley discharge of water - 220 l;
• performance of a septic tank per day - processing of 1000 liters of sewage;
• electricity consumption - 1.5 kW / day;
• all installations - 230 kg;
• overall dimensions - 2.5 * 1.1 * 1.2 meters.

If the connection depth of the septic tank is more than 0.8 meters, then it is necessary to install Topas-5 Long

On the site where the pool is located, you need to use a septic tank with a higher capacity - Topas-8 or Topas-10 (depending on the number of people living). Such models can process 1500-2000 liters of water per day.

The letter designations "Pr" and "Us" in the model range of septic tanks have the following decoding:

• Pr - forced water drainage (required at a high level of groundwater occurrence, removal occurs periodically using a pump);
• Us - enhanced water drainage (used if the septic tank is located at a depth of more than 140 cm from the level of the sewer pipe).

The cost of autonomous sewage is affected by the performance of the Topas septic tank (the price of a single-chamber septic tank serving 5 people will be significantly lower than the price of a two-chamber model with enhanced water drainage, designed for permanent residence of 20 people).

Do-it-yourself installation and connection of a septic tank Topas

Pit preparation

The first step is to choose a place to install a septic tank. Building and sanitary standards prohibit placing the treatment plant too close (less than five meters) to a residential building. However, it is not worth removing too much, as this will increase the cost of building the pipeline.

The installation of the Topas septic tank begins with the preparation of the pit:

There must be free space between the wall of the pit and the body of the septic tank - at least 20 cm

Installation of a septic tank and arrangement of the sewer system

Septic tanks Topas 5 and 8 can be installed in the pit without the use of lifting equipment, that is, manually. There are special holes on the stiffening ribs through which you need to pass the ropes, and carefully lower the septic tank to the bottom of the pit. Align the location of the septic tank using the building level.

The next stage is the supply of the pipeline and the arrangement of the sewer system of the topas septic tank.

The instruction involves the following steps:

The slope of the sewer pipe depends on the diameter of the pipeline. With a diameter of 100-110 cm, the slope is 1-2 cm per meter, and with a diameter of 50 mm - 3 cm per linear meter

Connecting a septic tank Topas

The next step in installing a Topas septic tank is connecting the power supply. To do this, you can use a PVA cable with a cross section of 3 * 1.5.

1. The cable must be placed in a corrugated pipe and laid in a trench near the sewer pipeline.
2. Insert one end of the cable through a special hole into the cleaning station and connect to the terminals.
3. Connect the second end of the cable through a separate machine (6-16A) to the switchboard in the house.

The final stage is backfilling with a dry sand-cement mixture. Sprinkling of the septic tank occurs simultaneously with filling it with water.

The installation is filled up by a third, and filled to the same level with water. Thus, the pressure on the septic tank body is compensated. The process of sprinkling and filling with water continues until the body of the septic tank is completely underground.

Installation and connection of the septic tank Topas: video

Durable and uninterrupted operation of the Topas septic tank is possible subject to a number of rules for its operation and maintenance.

The instructions for the treatment plant contain a list of permissible and prohibited actions.

During the operation of the Topas septic tank, it is prohibited:

• throw construction waste, polymer films and other inorganic compounds into the system;
• pour water containing potassium permanganate into the septic tank;
• pour disinfectants containing antibiotics and chlorine into the sewer system;
• dump large amounts of pet hair into wastewater;
• drain automotive oils, alcohol, antifreeze, alkalis and acids into the sewer.

During the absence of electricity, it is desirable to reduce water consumption in order to prevent overflow of the septic tank chambers and the release of untreated sewage into the external environment.

Regular maintenance of a septic tank is the key to the stable operation of an autonomous sewer. Septic service includes:

Topas septic biological treatment station is a modern installation for arranging local sewage. Despite the high cost, the Topas septic tank has gained popularity among consumers in different countries due to its efficient wastewater treatment, ease of use and low operating costs.

Until recently, biological wastewater treatment was considered an unacceptable luxury for an ordinary owner of a suburban subsidiary plot. And only in recent decades, the situation has changed dramatically, which is associated with the advent of septic tanks, in particular, treatment systems called Topas.

Devices of this type provide high quality wastewater treatment due to their decomposition under the influence of microorganisms (bacteria), which is not accompanied by the formation of waste that pollutes the environment.

Do-it-yourself installation of a Topas septic tank is quite simple from a technical point of view and can be performed by any user who has ever had to handle such equipment at least once. However, before installing it, and preferably before buying, it is advisable to familiarize yourself with all the advantages of a septic tank and the principle of operation of the device.

Device advantages

The main advantages of the Topas septic tank include:

• high efficiency of cleaning procedures;
• low power consumption;
• excellent tightness and low noise level generated by the device during operation;
• compactness and ease of maintenance.

We also note that when purchasing cleaning equipment, you are given the opportunity to individually select a septic tank for the needs of the family (depending on its quantitative composition). So, the Topas-8 model, for example, is designed to serve a family of eight people, and the Topas-5 is suitable for a family of five members.

Device and principle of operation

The main cleaning processes occurring in the settling tanks of the septic tank are the result of the vital activity of special bacteria that feed on organic matter and decompose it into elements ready for disposal.

Note! The device does not need special cultivation of bacteria, as they multiply on their own, feeding on sewage and oxygen.

A distinctive feature of the device we are considering is that its entire design is made in the form of a compact module, due to which the installation of a septic tank is noticeably simplified.

The device has four chambers and two built-in compressors that serve to keep the bacteria working, so that the decomposition process is accelerated.

The first chamber, equipped with a special float switch, serves to collect wastewater and settle it (with large particles of dirt falling to the bottom). When the chamber is filled to a certain level, the relay turns on the compressor, after which the drains are forcibly moved to the second chamber.

After passing through a coarse filter installed at the inlet of the second compartment, liquid waste enters the zone of influence of microorganisms and is cleaned of organic components. To speed up the fermentation process, oxygen is pumped into the chamber with the help of a compressor, which contributes to the mixing of wastewater with activated sludge, which acts as a kind of filter.

Sewage saturated with bacteria and oxygen then enters the third compartment, which is used as a secondary sump. In the fourth chamber, the final purification of water is carried out, which leaves the septic tank through a special channel.

Mounting

When choosing a place for the arrangement of the device, follow the recommendations below:

• The septic tank should be located in a pit, at least five meters away from residential buildings.
• The dimensions of the pit are selected depending on the model of the septic tank, and its walls are closed with formwork or laid out with bricks.
• At the bottom of the pit, a sand cushion with a thickness of about 150 mm is prepared.

Installation of a septic tank (its descent) is carried out using a system of cables pulled through special holes available on the stiffeners of the product.

After installing the septic tank in the pit, all the necessary communications are brought to it and, first of all, a sewer pipe. The insertion depth of the inlet pipe is usually 70-80 cm below ground level and depends on the distance of the station from your home. At a distance of 10 m from the pit to the house, the pipe is inserted at a depth of about 70 cm (at the same time, in the house itself, a sewer outlet is made at a depth of 50 cm).

After installation, complete sealing and thermal insulation of the device case is carried out. These activities must be carried out in accordance with the instructions supplied with the product.

Note! Even before sealing, the septic tank placed in the pit must be installed strictly according to the level (after that it will be impossible to straighten its position).

To supply electricity, it will be possible to use a cable of the PVS brand with a section of 3 × 1.5, laid in a corrugated pipe along the same trench as the sewer pipe.

And at the last, most important stage of arranging the device, it is backfilled with the previously selected soil, which is accompanied by pressure equalization on its walls. To this end, as the earth is added, the septic tank chambers are gradually filled with water, which compensates for the excess pressure of the soil on the walls of the device.

Video

This video shows the complete installation cycle of the Topas septic tank:

If earlier biological wastewater treatment seemed something unrealistic, then at the present time, thanks to the emergence of the new Topas septic tank treatment system, it has become quite feasible. The development of this unique method belongs to the leading domestic company for the production of wastewater treatment plants Topol-eco. An innovative feature of this system is the purification of wastewater by means of microorganisms. The process of processing and disposal of wastewater completely eliminates the possibility of environmental pollution. This system is environmentally friendly and complies with established standards for wastewater treatment.

The principle of operation of the septic tank Topas

As noted earlier, Topaz is a septic tank, the principle of which is to purify domestic water with the help of special microorganisms - anaerobic bacteria. Under their influence, organic compounds decompose, are disinfected and processed into sludge.

First, wastewater passes into the installation chamber (sector 1 in the figure), where the first stage of treatment takes place. In the process of it, large fractions of pollution are eliminated, after which the water is sent to the aerotank by means of an airlift (sector 2). The latter is the main part of the septic plant, where active bacteria are kept. It destroys contaminants that have managed to pass the first stage.

Sludge, which is formed as a result of waste processing, acts as a binder for particles of foreign bodies contained in water. After that, all the liquid goes to the sump (sector 3), called the pyramid. There, the silt settles to the bottom, and the finally purified water follows further (sector 4).

Filter sludge that accumulates in the sump should be removed periodically. The recycling process is quite simple and does not require special knowledge. If you plan to use a septic tank to give Topas, then silt can be used as a fertilizer.

Characteristics of the septic tank Topas

I would like to briefly dwell on the unique characteristics of this septic plant. Among them are:

• cleaning efficiency (99%);
• compact design;
• low power consumption;
• no noise during the working process;
• Topaz-septic tank is an automated device: it does not require special operating conditions and is easy to maintain;
• tightness that prevents the spread of unpleasant odors.

Here it should be added that users can easily choose the appropriate version of the septic tank for their needs. So, different models differ from each other in the number of users.

For example, Topas 8 and Topas 5: the first is designed to serve 8 people, the second, respectively, to 5.

Installation of a septic tank

It can be divided into six main stages, which we will consider in more detail using the Topas 5 model as an example.

Stage 1: site preparation

Topas septic tank instructions provide for installation at a distance of at least 5 meters from the foundation of the house. This recommendation is dictated by the norms of SES. After the place is determined, a pit is pulled out. Its dimensions are determined depending on the model of the septic tank. Topas 5 has dimensions of 1000x1200x1400 and for it the pit should be 1800x1800x2400. After it is dug, it is required to make a formwork.

Stage 2: installation of a septic tank

Next, in the pit, it is necessary to organize a sand cushion. To do this, its bottom is covered with sand by 15 cm. Thus, after installation, the septic tank will also rise above the soil surface by 15 cm. This is required for the convenience of operating the cleaning system in the spring season and preventing its damage. Otherwise, if the septic tank is installed flush with the ground, in the spring, during the snowmelt, the aeration station may be flooded. As a rule, water will get inside through the ventilation vents or the top cover. In this case, the compressors, and sometimes the entire system as a whole, may stop functioning.

Pro tip:

It is necessary to choose a model of a treatment plant taking into account the level of groundwater occurrence. If it is very close to the surface, then preference should be given to varieties marked PR. In such systems, a forced removal of treated water is provided, which is carried out by means of a built-in pump.

Septic tanks for a country house Topas (5 and 8) can be installed manually in the pit. No special equipment is required, unlike other models of these systems. A rope is threaded through special holes, which are located on the stiffening ribs, and the station is lowered into the pit.

Stage 3: organization of the sewer system

For HDPE pipes, diameter 110 mm are used. The depth of the tie-in level of the pipe into the septic installation is 70-80 cm relative to the upper ground level. For stations of the Long model, the depth varies from 120 to 140 cm. The slope of the sewer pipes depends on the diameter of the pipe:

• at 100 mm - 1-2 cm per meter;
• at 50 mm - 3 cm.

If the pipe insert was made at a distance of 70 cm from the top, then at a distance of 10 m from the house, the height of the pipe leaving the house should be 50 cm from the ground.

Stage 4: sealing the installation

In the outer case of the station, it is necessary to drill holes for the sewer pipe. To do this, it is recommended to use an adjustable crown (diameter 103-100 mm). In this case, the adjustment should be 105-108 mm. It is desirable to carry out sealing guided by the instructions.

The station is equipped with a special polypropylene cord, with the help of which the branch pipe placed in the hole is soldered to it. To do this, use a building hair dryer with an appropriate nozzle. After the pipe is securely attached, a sewer pipe is connected to it.

Pro tip:

Before sealing, it is worth leveling the installation using a building level.

Stage 5: providing a power source

Since the system is powered by electricity, the installation of the Topas septic tank provides for power supply to it. For this, a PVA cable (section 3x1.5) is used. It is placed in a corrugated pipe designed for earthworks, and placed near the sewer pipe.

The cable is brought to the unit through a special input and connected to the terminals. In the house, it is connected to the switchboard through a separate 6-16 A machine.

Stage 6: pressure normalization

The final stage is equalization of pressure on the outer surfaces of the station during its sprinkling. This is necessary in order to compensate for the pressure on her body. Filling the installation with water and sprinkling are carried out simultaneously and in the same quantities. The station is filled with water by a third and similarly by a third it is filled up. The process is repeated until the station is submerged into the ground to the required level.

Exploitation

From all of the above, it can be seen that it is quite feasible to install a Topas septic tank with your own hands. Nevertheless, if you have not had to deal with this kind of work before, it is better to turn to specialists. As for the operation, it is not associated with great difficulties. Operating features:

• It is recommended to clean the sump 1-2 times a year. If it is not possible to use the sewage equipment, you can do it yourself using a conventional deposit. The pumped-out sludge is suitable for use as fertilizer.
• Replacement of compressor membranes and cleaning of filters should be carried out at intervals of 2-3 years. These procedures can also be performed independently with a screwdriver and a wrench.
• The aeration system of the station is replaced every 12 years. This is necessary to ensure the normal functioning of the installation. Despite the fact that all contaminants are completely recycled, it is possible that large particles enter the septic tank. If they are not removed, the installation may fail.

So, maintenance of the Topas septic tank is quite simple. With the timely implementation of the necessary measures to clean it and replace certain elements, the station will serve for decades.

Related videos

The TOPAS septic tank is a unique offer on the modern market that allows you to radically solve the problem of accumulation and treatment of wastewater at any type of facility, regardless of their location and distance from centralized sewer systems.

Autonomous sewage - a compact and fairly easy-to-use device that allows you to clean wastewater up to 98%. Drinking and using such water for cooking, of course, is impossible. However, recycled water becomes transparent, has no odor and is absolutely harmless to the environment. Moreover, by attaching a special storage tank to the septic tank, it is possible to ensure the secondary use of water: for watering plants, washing fences, garden furniture, etc.

Model Selection Rules

Before planning and carrying out the installation of a TOPAS septic tank, it is necessary to decide on the choice of a specific model. Our company - "Topol-Eco" for the most complete satisfaction of consumer needs, has developed and organized a highly efficient production of various types of septic tanks.

The choice of a septic tank model suitable for the parameters must be carried out according to the following main criteria:

• The number of people permanently residing in the house (dacha, boarding house, etc.).
• The maximum volume of wastewater treatment.
• Limiting value of volley discharge of water (with simultaneous use of a bath, shower, sinks, etc.).
• Ground water level.

So, for example, for installation in a country house, sewage equipment designed for use by up to 5 people inclusive, installation of TOPAS 5 is suitable.

If the house is designed for 8 people, it is equipped, for example, with 2 shower cabins, a washing machine, a dishwasher, etc. - the best choice is the installation of a TOPAS 8 septic tank. In just 2 hours, such a station is able to receive and process up to 440 liters. drains.

It is preferable to choose Topas 10 if the estimated value of wastewater treatment within 2 hours should reach 760 liters. As a rule, this is a house with 10 living people. It is possible to combine the system and the Topas septic tank, installation of the tenth series, when organizing an autonomous sewage system for 2 houses located nearby.

If you have a high level of groundwater in your area, then you need to choose devices marked "PR"

Topas professional installation is a guarantee of reliability and durability of the system

Installing a Topas septic tank is a relatively simple job. The main thing is that during the installation and commissioning of the system, all technological subtleties, design features, as well as requirements are taken into account:

• SanPin (2.1.5.980-00)
• SNiP (2.04.03-85)
• other regulatory documents.

When installing Topas, it is important to strictly observe the technological chain of sequential operations. Main stages:

• Decide on the place of installation.
• We are preparing a pit, the size of which should ensure the free installation of the septic tank body and the possibility of fixing it.
• We carry out the installation of a system of sewer pipes laid from the building to the septic tank.
• We bring power supply, cables to ensure reliable operation of the treatment plant.
• We install the septic tank in a regular place, we dock all the structural elements. We check the tightness of the system.
• We fine-tune the operation of the septic tank, after which the object, ready for operation, is transferred to the customer.

The preparation of the pit begins with the selection of a site. This must be done in accordance with the requirements of sanitary standards. As a rule, installation is planned in one of the most distant corners of the site from the buildings. There should not be a well, a pond, or other bodies of water nearby. It is necessary to tear off the pit, taking into account the overall dimensions of the treatment plant. For convenience of work during installation and connection, it is necessary to provide an extension of 20-40 cm on each side. A soft sand cushion is laid at the bottom of the pit, the layer thickness is 15-20 cm.

Works are carried out with the help of special winches or lifting equipment. Light models of the septic tank Topas (5 and 8) installation can also be done manually.

Further, the supply and fixing of sewer pipes is carried out. The standard diameter is 110 mm, as a rule, it should be used. Pipes are connected to the septic tank at a depth of 70-80 cm. If, due to difficult soil, high water levels, the Long model is used, the insertion depth will be at the level of 120-140 cm.

Trust installation only to professionals

The specialists of our company are ready to install the Topas septic tank quickly, efficiently and inexpensively. Each client will be guaranteed the perfect quality of the equipment, provided the possibility of long-term flawless operation.

You can apply for the provision of the corresponding service directly on the company's website, or by calling. Depending on the goals and objectives to be solved, financial capabilities and other conditions, the Topas septic tank can be installed in the following options:

• Standard installation.
• Installation chief.
• Installation of Topas "turnkey".

Maintenance features

The Topas septic tank is a reliable, highly efficient treatment plant. It is able to work for a long time and process wastewater with high quality. Its maintenance, contrary to expectations, is simple, consists in periodic inspection, periodic pumping of excess sludge, removal of particles that cannot be processed.

The best solution when organizing maintenance is to contact specialized service centers. StroyRemService LLC has created all the necessary conditions for carrying out work of any degree of complexity, high-quality and inexpensive maintenance of septic tanks.

Our advantages

The company has created ideal conditions that allow performing work of any complexity at the highest professional level:

• selected highly qualified personnel,
• all our specialists have extensive practical experience in the installation and connection of septic tanks of various sizes;
• all equipment, professional tools, special equipment,
• the technology of production of works is clearly developed, strict quality control is carried out.

We issue a quality certificate to each client - this is a guarantee of reliability and impeccability of the installation performed.

We never overestimate the strictly fixed cost of the service provided. On the contrary, if possible and appropriate, the installation of a septic tank will be organized in such a way as to make it the most profitable and affordable for the company's customers.

Contact the professionals!

Water drainage schemes