Homemade smoking pipe for tobacco. What wood is suitable for making a smoking pipe

Making a pipe with your own hands is a long and laborious process. This will require material, tools, skills and experiments. As practice shows, even for experienced carpenters, the first copies are far from the best quality. What smoking pipes are made of is a whole science.

A handmade smoking pipe is made of wood. The optimal material is briar, but it is almost impossible to find it in free sale. Briar is extracted from the root of the heather, which grows in the Mediterranean. Therefore, as a rule, cherry or pear wood is taken as the basis - available materials for a smoking pipe.

It is worth saying that making a smoking pipe with your own hands will cost many times more than buying a new one. This is due to the laborious process of sawing out the base, preparing the material, as well as clarifying the internal channels. You will have to spoil more than one blank before you get some semblance of a smoking device.

Many are wondering how to make a foil pipe, a bong from a bottle. It cannot be called a smoking pipe, since plastic and artificial surfaces do not have the effect that wood and briar do.

Technology and production does not allow the use of paper products.

You can focus on pottery, rust, but the slightest crack will render the product unusable.

Ready solutions

Tobacco stores sell original kits that will help you understand how to make a smoking pipe with your own hands in just 5 minutes. These are the so-called hobby blocks. Usually a hobby block is made in the form of a square or rectangular block of wood. A hole has already been drilled inside for the bowl and the smoke channel.

All that remains for the user is to attach the mouthpiece. You can also buy a drip tip on the online space, and according to the sizes that hobby blocks have.

To be honest, the hobby block is just a pipe making toy. It is problematic to make a full-fledged tube out of this. In most cases, such products are considered exclusively as souvenirs.

Equipment preparation

The key tool is a band saw and a drilling machine. You can find a machine in a used condition for about 5000-7000 rubles. through online advertisements. These are the simplest models that are easily fixed on the kitchen table.

It is not so easy to find a band saw for making smoking pipes and the device will most likely cost more. However, if tubes are to be manufactured in the long term, such equipment will become indispensable.

The next element of the preparatory kit is a drill. For the smoke channel, models with a diameter of 4 mm are usually selected. You can find such products for machine tools in specialized stores. The best option is a furniture hinge drill, with which repairs are made, including a wide range of options, ideal for creating a tube.

If carving is intended, art kits will be required. Carved decoration is a labor-intensive process.

Steps for making a smoking pipe

You can learn how to make a pipe for smoking tobacco according to the following steps:

How to make a mouthpiece?

The optimal choice for the mouthpiece is ebonite. Smoking pipe material can be purchased at hardware stores or in the same specialized tobacco stores. Before you make a bong or pipe, you should buy ebonite in reserve.

A piece of ebonite is vertically installed in a drilling machine. First, a perpendicularly flat surface is created with a drill. Next, holes are made for the trunnion in accordance with the parameters of the chubuk.

The most difficult part is drilling the smoke channel in the mouthpiece. It is important to remember that the hole must be tapered in length. Usually, drills with a diameter of no more than one and a half millimeters are selected, but in any case, exactly the drill is selected that fits under the smoke channel of the chubuk.

To make the hole tapered, the mouthpiece is drilled each time with thinner drills and in several passes. Wooden pipes in this case smoke better.

Some make and make pipes from clay, paper, and other improvised means. But this is a qualitatively different technology, which is problematic to implement without skills. Briar pipe bush and ebonite are the best materials.

In contact with

The sandbox is one of the favorite places for children to play. So that the sand does not crumble throughout the yard, and it is convenient for children to play, you can independently build a sandbox with closing doors that can easily be transformed into benches. Materials To build a sandbox with your own hands, you will need: boards; self-tapping screws; screws; grout for wood; meter; loops; pencil; protective glasses; circular […]

to bookmarks

In this master class, we will make a modern and stylish knife stand made of natural wood. All details with photos below. Materials Before starting work, prepare: boards; bamboo skewers; stain; roulette; wood putty; small nails; wood glue; clamps; pencil; saw; grinder or sandpaper. Step 1 Based on the number of knives you have and […]

bookmark 1

This tripod is suitable for both video and still cameras. It folds up conveniently for easy storage. You can easily make a tripod with your own hands. How exactly, you will learn in the above and described master class. Materials Before starting work, be sure to have: boards made of durable wood with a thickness of about 1 cm; screws; steel bars; plastic cases […]

bookmark 2

You can make an effective mini-stove for camping conditions from an ordinary thermos. In order for the flame to flare up more efficiently, and the contents to smolder much better, a home-made fan should be sent in pair with the burner design itself. We will tell you in detail how to make a mini-stove with your own hands in a step-by-step instruction. Materials To make a mini-burner you will need: a thermos; drill; drill; aluminum plates; aluminium case; […]

to bookmarks

You can make an interesting technological table lamp from a small old engine. It looks very urban. And to turn the lamp on/off, you just need to turn the engine piston, which will actuate the switch. Materials To make lamps from an engine, prepare: an old engine; marker; cardboard sleeve; hacksaw for metal; grinder; wire brush; solvents; primer; paint; pieces of wood […]

bookmark 1

An ordinary iron can from drinks can easily turn into a candlestick. In this master class, we will not just cut it, but by making an interesting ornament for a beautiful effect, we will keep the shape so that we get the feeling that the jar has remained intact. ATTENTION. The jar is heated by a candle, and therefore do not leave it unattended without extinguishing the flame. Materials To make […]

bookmark 2

Sawing round logs by hand and alone can be extremely difficult and inconvenient. Many people do this by laying logs on benches, but this is time consuming, since after each manipulation it is necessary to re-balance so that the log does not roll. In this master class, we suggest you make a stand-holder for manually sawing logs. Despite the simplicity of the design, it will become […]

bookmark 1

An old stool can be turned into a handy turntable. For this we need its round seat. The rotating mechanism in the tray is necessary so that during dinner each member of the family can turn it to the right side. You can put spices, sauces on a tray, or just put a vase of flowers on it. It looks very interesting and stylish. Details […]

to bookmarks

The fascination with Star Wars has given rise to a whole series of various trifles and accessories depicting the characters that the audience has fallen in love with. This quirky Darth Vader helmet pendant can be made by hand with little effort. The hardest part of the whole manufacturing process is finding the right plastic packaging in the shape of the infamous helmet. In this case, it was a package of sweets, you can […]

to bookmarks

A cardboard stand for a tablet is good because it takes just 20 minutes to assemble and does not require any financial investment. You can make it even on the road and, being far from home, if you forgot the usual stand or cover at home. The materials used are quite light, but the design itself and the method of attaching its elements make the stand stable. Materials for […]

bookmark 1

It's amazing that trends are literally in the air and often even those who do not follow them create things that resemble the hits of design exhibitions. Muscovite Elena Sokolova made furniture “from branches” no worse than the students of the Danish Design School. Elena Sokolova masterfully handles an ax and a jigsaw: she herself invented, designed and manufactured laptop tables, lamps and […]

bookmark 2

Using the papier-mâché technique, you can create very unusual decorative decorations for a room from threads. One of them is a vase. It can be decorated in any color, but it looks most impressive in the white version. Remember that this vase cannot be filled with water! Materials: Ball. Glue. Papier-mâché paste. Threads. Paper. Brushes. Scissors. Cardboard. Scotch. Film. Step […]

to bookmarks

This interesting version of the shelf in the interior can be beaten in many ways. For example, instead of an uncomfortable and bulky bedside table. In this case, the countertop was chosen so that you can put a book and gadgets on it. The cut was chosen with a crack under the charger cord from the smartphone. Also on the shelf you can put an alarm clock, a pot of flowers and other […]

bookmark 1

The shelf presented in this master class will perfectly fit into the space of a small area due to its collapsible design. If necessary, it can be a regular shelf on which books and other items stand, or you can fold it so that it takes up as little space as possible. To learn how to make a folding shelf with your own hands, read the following […]

bookmark 1

We already had a similar master class using a mirror, but now based on it we will make an even more interesting thing for the house - a wall clock with an infinity effect. The details of this process in stages and with a photo are presented below. Materials For work you will need: an old round wall clock; round mirror with a 10 mm hole in the center; […]

bookmark 1

You can make a simple and cute case for your gadget yourself. You do not need special skills and abilities in fabric processing. It is very easy to build a pattern for him, and you will need very little material. For details of the process of how to sew a fabric cover for a laptop with your own hands, read and see further in the master class. Materials For work, prepare: a piece of cotton [...]

Today we will tell you how to make a handmade pipe at home. If you already smoke, you need to customize this process: cigarettes from a pack and a lighter for three rubles is not a dude's choice. The tube is another matter.

Frankly, I myself smoked a pipe - of course, until I quit. The case was interesting. Hammering and lighting a pipe is a whole science, we have already told you about this. My pipe has always interested others: friends asked me to try it, and in public places (for example, in cafes and bars, before smoking was banned there) I always got into the center of attention, as soon as I got comfortable with my pipe. In general, you probably already understood that the pipe is royal, especially if you made it yourself.

So, you will need:

• briar (wood);
• ruler;
• chisels for woodcarving;
• saw;
• pencil;
• drill with different drills;
• compass;
• polishing machine;
• sandpaper;
• cutters - at least 18 mm;
• time (many);
• idea.

Idea

First of all, you need to understand what your pipe should look like. Draw the options on paper and choose the one you like best.

Embodiment

Cut off a piece of wood of the right size - your pipe will only be slightly smaller.

Draw an outer circle - the diameter of the pipe - and an inner circle - the diameter of the recess in it, where you will fill the tobacco.

Now we draw on the remaining sides of your bar the selected shape. It's up to the small thing - to trim the tree so that the idea is embodied in your bar (grab the tools and work). As a result, you will get approximately what is shown in the picture.

Drilling

You need to drill a hole through which the smoke will enter your mouth.

As you can see from the picture, you first need to measure how deep you have to drill. Be careful: the walls of the tobacco chamber must not be thin, otherwise the high temperatures will destroy your pipe.

The wall thickness of the tube shown in the picture is 8 mm. Tobacco chamber diameter - 18 mm, depth - 30 mm.
In the end, it is clear that the dimensional characteristics depend on the chosen design.

Now you need to make a hole in the mouthpiece, which will connect the mouthpiece to the tobacco chamber. Carefully drill a hole (a 7mm drill was used to make this tube). Then we change it to a smaller drill (in our case, 3 mm). Do not forget to test - how well does it pout, is the connection between the tobacco chamber and the mouthpiece improved?

We round off

Should the tube look like a tube? Who has seen a cube-shaped tube? This is some kind of cubism.

We grind

This will require sandpaper and a lot of patience. Sand until you're happy with the texture.

Finishing

We connect one with the other and make minor adjustments.
The handset cannot yet be used. You need to polish it - for this you need a polishing machine.

Tobacco smoking is very popular, despite all the warnings of doctors. There are many different ways to do this, but the pipe is especially popular. This item gained its fame around 1493, after the discovery of America by Columbus. The first pipes of the Indians were shaped like the letter "U". The smoke from the tobacco burning in them was drawn in through the nostrils.

A little about the device

modern beautiful,carved smoking pipeshave a completely different, long-established structure. It has three main parts:

bowl;

shank;

mouthpiece.

There is a tobacco chamber in the bowl, combustion takes place in it. Through a small hole in the base of this chamber, the smoke goes into a special channel (chimney) that passes through the chubuk. Then it follows into the mouthpiece connected to it and from there into the mouth of the smoker. The pipes have many different shapes, they are made from different materials and even have some variations in their design.

What is the secret of rich taste

Why is it so attractive to smoke a pipe? The thing is that tobacco, burning in it, acquires a stronger taste, respectively, and the smoker feels a bright and rich flavor range. But in order for it to open completely, the tube must not only be made of the right material, but also have a specific shape. All this may seem very complicated at first glance. In fact, it is quite possible to acquirehomemade smoking pipe. Using this will definitely be more pleasant than the highest quality and most expensive store product.

Getting Started: Choosing a Model

Before starting work, you need to decide on the device of the tube. One moment is fundamental here - it will be with or without a filter. The first option provides for the presence of a special chamber in the product, where a special smoke purifier will be placed. It is made from paper, activated carbon, balsa wood and other materials. A good filter does not affect the taste of tobacco, but only reduces the amount of harmful substances in the smoke, cools it and absorbs moisture from it. All this, of course, is good, but it will be necessary not only to make a compartment in the tube for such a cleaner, but also to regularly change used filters. There is an easier way (it is used in inexpensive tubes). An evaporator is inserted inside the joint between the stem and the mouthpiece (a small metal cylinder with a groove for smoke to flow through). It plays the role of both a cooler and a resin collector. Its efficiency, of course, is small compared to the filter, buthomemade smoking pipemay well get by with just the presence of an evaporator.

About the tool

After everything is decided with the tube device, you need to take care of the tool. The required minimum is as follows:

file;

sandpaper;

any device for drilling;

band-saw;

set of chisels (forcarved smoking pipe)

pencil;

tassel.

blanks

Next, you need to take care of the blanks for the tube. The Internet is full of sites where you can order everything you need, the only question is price and shipping costs. By and large, you need to purchase only a piece of briar for making a stammel (a bowl with a shank) and a small (about 10 cm long) cylinder of ebonite with a diameter of 1.0 - 1.5 cm for turning the mouthpiece. It is better not to even try to take these two things somewhere with your hands, but only in special stores or from trusted suppliers on the network. Of course, you can also take care of a decorative ring for a pipe or other similar decorating elements, but for the first homemade product, this is all absolutely superfluous.

Manufacturing technology

Now, finally, considerhow to make a smoking pipehimself. First you need to use a file to give the briar the shape of the future stammel. Its contour is pre-drawn on the tree, so it will not be so difficult to do this. The main thing is not to forget that the total length of the tube should be at least 10-15 centimeters.

Having given the briar the desired shape, they proceed to drilling the tobacco chamber, holes for the trunnion (the part of the mouthpiece that is inserted into the chubuk) and the smoke channel. This must be done carefully, at the lowest speed and with regular extraction of the drill from the workpiece. Otherwise, it will simply start to burn, and this cannot be allowed in any way. It is better to drill the smoke channel first and not to the end, so as not to miss when the tobacco chamber is drilled. It is better to make a hole for the trunnion of a small size (as far as the workpiece allows) in order to prevent chips and cracks on the walls of the cylinder resulting from this process. Then they already take up chisels, if donecarved smoking pipe, and in the end everything is finally processed with sandpaper.

We also make an ebonite mouthpiece with a file. This material lends itself well to processing. The main difficulties lie in drilling a smoke channel in it and fitting the neck of the mouthpiece to the diameter of the seat in the shank. The connection must be tight and at the same time easy to separate with little effort. It is important to know that the mouthpiece is inserted and removed only in a circular motion, and it is screwed only clockwise, and unscrewed, on the contrary, against it. The final form of the mouthpiece will be determined only by the imagination of the master.

Even if something does not work out the first time (and this, most likely, it will), then you should not despair. Invaluable experience is gained only in work. Given the mistakes of past attempts, it will be much easier to achieve mastery and eventually make a first-class pipe for yourself.

Smoking pipes have been around for ages. This is a very popular item and comes in a variety of styles, from Player to Church Keeper. How to make your own smoking pipe?

I don't smoke, so I made just for fun. There are many ways to make your own smoking pipe. You can lathe it out of the halves and then join them together, you can carve it out of wood and then drill a channel from the leg to the other end. But in this simple step-by-step guide, we will cut two identical shapes out of wood and use a dremel to cut out the inside, then glue the two halves together.

Step 1: Cut out the tube

Print the PDF file on an A4 size sheet of paper. Cut out the stencil and draw it twice on a piece of wood 2 cm thick. When you draw the outline of your homemade smoking pipe, it is very important to make sure that the stem is parallel to the grain of the wood.

If you draw it perpendicular to the fiber, the tube will be very brittle and will probably break. Next, cut out two shapes. I used a band saw for this, but you can use a jigsaw or anything you have on hand. Files

Step 2: Drilling the bowl

You will need a 2 cm drill bit, a drilling machine (a regular drill will also work, but may not be as accurate), and a clamp. Align the two halves and pinch them at the bottom. Then draw a straight line from the top right corner to the bottom left. Draw another line from the top left corner to the bottom right corner. Where both lines intersect and you need to drill a hole. Slide the 2cm bit into the drill press and drill so that the point of the bit goes straight into the center of the bowl. Go down 2.5 cm and stop there.

Step 3: Make the Air Duct

I've attached an image to this step - this is the duct diagram you need to cut out. Copy it onto the tube halves so that when you fold them in half, the duct pattern is inside. Use a dremel to cut the duct, don't make the groove too deep. Once you're done with the cut, align the two halves of your tube so that the duct is inside. Place your lips on the end of the barrel and blow. If the air passes easily, then you are ready to move on to the next step. If not, keep cutting until you can blow air through the barrel.

Step 4: Glue the halves

Get some strong wood glue and apply some where you haven't cut anything and put very little glue on the trunk because when you put the two halves together the glue will want to seep into the air duct and block it.

Squeeze the two halves together or place them in a vise for several hours. Once the glue is completely dry, remove the tube from the vise and blow hard into it. If you have been able to do this, then you are ready to move on. If not, place the tip of a flat-head screwdriver on the seam where the halves of the tube meet and tap the screwdriver with a hammer to separate it. Sand off all the glue and cut the duct a little deeper, and then try to glue the halves together again.

Step 5: Cut out the stem

You can use a hacksaw or band saw for this step. I chose the hacksaw because I could control it better. Mark a line on each side of the trunk indicating what you want to cut. Make sure the stem you're blowing into expands at the end. The wider end will fit more comfortably in your mouth. Place the tube in a vise and tighten it from below. Carefully cut out each line you have drawn.

Step 6: Skin the barrel

Use a dremel to cut the corners of the trunk. Continue cutting out the stem until you decide it looks good. Use 80 grit sandpaper and sand the barrel a little. Next, take 150 sandpaper and go over the barrel again. Keep increasing the grain until you get to 500 grit.

Step 7: Cut and Sand the Bowl Section

I clamped the tobacco pipe in a vise and cut off all the corners of the bowl with a hacksaw. Be very careful not to cut too much. Once all corners are cut, take 80 grit sandpaper and sand the entire bowl. You can sand by hand, but it will take a very long time, so I advise you to use suitable power tools. Once I was done with 80 grit, I decided to sand by hand and took a piece of 150 grit. Raise the grit as you did when sanding the barrel.

Step 8: Finishing up

I used wood stain to give my trumpet some character. But don't paint it if you plan to smoke, because when you light the pipe, it will catch fire. Next, I varnished it. Once again, if you are going to smoke from this pipe, do not use varnish, stain, etc. I only used lacquer because I don't intend to smoke.

If you're looking for a finish that won't catch fire, try mineral oil. Mineral oil is safe and can be used to finish smoking pipes. Apply some mineral oil to a piece of 1500 grit sandpaper and go over the tube with this sandpaper. Once the entire tube is sanded, polish it with a rag or paper towel. Now everything is ready! Enjoy your new handset.