The simplest do-it-yourself sheet metal whistle. How to make a wooden whistle yourself? How to make a whistle from a tree diagram

So, we need an even willow rod, 7-10 millimeters thick. Why willow? Because it is very easy to remove the bark from a willow wand without damaging it. And this, as we will see later, is very important for us.

In addition, willow is a plant with brittle branches, which means that you do not have to spoil a living plant. It is enough just to take a walk under a willow tree after a fresh breeze to collect a bunch of branches, just the ones we need.

We select a branch with intact and even bark (this is a very important condition), if possible, without knots. Now we need to find on this branch a flat area 4-7 centimeters long. There may be buds in this area (this is common with willow), but in no case should there be any knots.

Now we cut the branch along the border of a flat area. At the other end of the section, we make an annular incision, as shown in Figure 1. The incision should be deep enough and slightly (precisely slightly) cling to the wood. To make sure that the entire layer of bark is really cut through, you can remove a ring 1-2 millimeters thick.

After that, we begin to lightly “tap” the bark with a small hammer in a circle in all places. Instead of a hammer, you can use a knife handle (Figure 2). Instead of tapping, you can also “roll” a branch. This is done with the aim that the bark subsequently peels off the wood more easily.

We make a cutout on the branch, of such a shape as shown in Figure 3. After that, carefully, with rotational movements, we try to remove the bark from the branch without damaging it. You should not hurry, if the bark is not removed, you need to knock on it again and try again. In the end, it will definitely be removed (Figure 4).

Now, carefully cut off the “round” with a knife from the branch left without bark just along the line of our cutout, as this is done in Figure 5

Then we cut off the round barrel (Figure 6).

Do not try to cut it absolutely straight, it will not work anyway. Yes, we don't really need it. If the cut turns out to be wedge-shaped, as in our drawing - this is only for the better - it will be easier to adjust the sound.

We insert the cut circle into its original place, cut up. If the cut turned out to be oblique, then we put it as a bottleneck to the hole (Figures 7 and 8).

Now, attention. We clamp the open end of the resulting tube and blow it strongly enough from the side of the round. The result will be a distinct whistle. True, its timbre may not be very beautiful.

Don't worry, we'll fix it now.

We cut off the remaining end of the stick, insert it into the open end of the tube and, moving the stick back and forth, select the most pleasant timbre of the whistle (Figure 9). Then we cut off the protruding part of the branch and the whistle is ready! (picture 10)

Attention! Our whistle gives a rather loud whistle. Therefore, the best place for exercise is a summer house or a country house, but not a city apartment.

And finally, one piece of advice. If you manage to find a willow twig with a fairly long section of even bark, 10-15 centimeters, then instead of a whistle you can make a simple home-made flute. It is made in the same way as a whistle, but instead of choosing the timbre of the sound, just plug the open end with a wooden cork, and in the remaining space, make 3-4 holes in the bark so that they can be plugged with your fingers at the same time. By opening one or another hole in turn, we can reproduce the simplest melodies. Of course, our notes will not correspond to the natural scale, but we do not need it. The main thing is that the melody is pleasant.

© www.freee.ru/masterskaya/samodelnyi-svistok-iz-vetki

homemade whistle

If you pass or drive with your young son past the willow bushes, do not forget to make a short halt in order to take the opportunity to strengthen your paternal authority. When in front of your son you cut a real working whistle from a willow wand, showing him how it is done, he will respect you even more. An unsightly homemade whistle will be the pride of your offspring in front of their peers.

If you are a city dweller, you may not know how a wooden whistle is made, so read on.

We need a smooth willow branch with a cross section of about a centimeter. Why the willow branch? But because you can easily remove the bark from a willow wand without damaging it. And this is important, since a single piece of bark will be the body of the whistle. In addition, willow branches are brittle, with a fresh wind under the willow there will always be a bunch of suitable branches, and you will not have to harm a living plant.

We select a branch on which there is a section 5-8 centimeters long with intact and even bark without knots. Kidneys in this area are allowed, they will not interfere with our product.

We cut the branch at one end of the selected section. At its other end, we make an annular incision of sufficient depth, slightly clinging to the wood. We can even remove a narrow (millimeter wide) ring to make sure that the entire bark layer is cut through.

Then lightly tap the bark of the area with a hammer or knife handle over the entire surface. Instead of tapping, we can “roll” a branch. This operation will then make it easier to peel off the bark from the wood. After that, on the branch we make a cutout as in the figure on the right.

Now, with rotational movements, we carefully try to remove the bark without damaging it. We are not in a hurry: if the bark is not removed, we tap it again. She's bound to come out eventually.

From the section of the branch remaining without bark, we cut off a cylinder with a knife along the line of the transverse incision. We cut off a small segment (barrel) from this cylinder. We don’t try to cut absolutely exactly, if it turned out to be a wedge, it’s even better: it will be easier to adjust the sound of the whistle.

We insert the cropped cylinder into its original place, cut up. If the cut turned out to be a wedge, then we put it as a bottleneck to the hole.

It's about to be a whistle! We clamp the open end of the resulting tube with a finger or palm and with sufficient effort blow into it through the cylinder. We hear a distinct whistle. The timbre of the sound on the move may not be very pleasant, but this is fixable: we will adjust the sound.

Having cut off the remaining end of the branch, insert the resulting piece into the open end of our tube and, moving it back and forth, adjust the timbre of the sound. Having picked up the most pleasant timbre, we cut off the protruding part of the piece. The whistle is ready.

Give it to your offspring and warn him to whistle anywhere, but not in the apartment, as the whistle makes a rather loud sound. Let him whistle with his friends in the yard.

While making a whistle, you might have a desire to make a more sophisticated whistling instrument - a pipe. And you can do it! You just need to find a willow branch with a section of even bark 15 centimeters long. The pipe is made using the same technology as the whistle, only the open end of the tube is simply plugged with a wooden plug (which does not move back and forth). On the remaining part of the bark, 3-4 holes are made so that the fingers of the hand can plug them at the same time. By opening one or more holes in turn, you can play simple melodies. Of course, the resulting notes will not correspond to the natural scale, but there will be a semblance of a melody!

The most valuable gift is a handmade gift! To make it interesting, original, unusual, you will need not so much time and effort! The main thing is desire. If you have, then this article is for you.

Whistle- a great, unusual gift for any child and for every adult. The task is not the easiest to make the whistle work, whistle the first time. This will require your patience and care.

How to make a whistle with your own hands?

You will get a very beautiful and interesting toy if you make a whistle out of wood! It will turn out natural, natural and alive! It will bring joy and pleasure to its owner. When choosing a tree for a future whistle, willow or linden is usually preferred, since you can easily peel the rod without damaging it at all.

How to make a whistle from a tree?

1. Be careful when choosing the future basis for the whistle. It is necessary to choose a beautiful rod, the thickness of which will be approximately like a finger, about 12 millimeters and cut it off. It is very important to choose a branch with a smooth, beautiful skin, because this is the basis of the future whistle. The length of the branch can be from 5 to 7 centimeters.

2. After you have chosen the desired rod, you need to cut it from all kinds of knots, leaves and small twigs. It is necessary to clean it from this, the rod should be even and smooth. Next, you should cut off the edge of the future workpiece.

3. The next step is to make a small wedge-shaped cut. It should be made deep enough. The notch should catch on the wood. You need to make such an unusual mark, which will soon be needed and will help your future creation.

4. The next step is an annular incision. It must be done 4 centimeters from the end of our rod. The rod should be cleaned of bark, this can only be done with a deep incision.

5. Need to tap the rod. For quick and convenient tapping of the rod, you can use the handle of the most common standard knife. It is lightweight and easy to use.

6. A very delicate task - you need to remove the bark. We scroll the workpiece, and carefully remove the bark with a knife. You must be sure to succeed!

When you peel the bark, it will look like this:

7. Have you forgotten about the unusual mark we made earlier? Now she is useful to us! It is necessary to remove small roundings of wood. Very important: it is necessary to give it the shape of a strip.

A homemade whistle is a fun toy with funny sonorous trills, which you can make from paper, tree branches, cans, plastic corks. We have collected the most interesting and proven ways to make a whistle - choose the material and follow our advice.

How to make a wood whistle

For the whistling mechanism, a freshly cut, even sprig of willow or hazel, 15 cm long, 2 cm in diameter, is suitable. You will also need a sharp knife and some free time.

• Cut vertically one tip of the twig, and on the second - make a circular notch.

• On one side of the stick, closer to the edge, cut the bark in the form of an English letter - D. Tap the blank with a knife so that the bark comes off, then press it with your fingers, and it will move off the base itself.

• From the bare rod, cut off a small rectangle at the place of the annular basting and cut off part of the wood from it - a gap for the whistle.

• Insert the resulting part into a case of bark cut up. Insert the remaining piece of the twig into the bottom of the whistle.

• Blow into the upper hole of the tube, and alternately raise and lower the stick-sleeve with your hand, adjusting the sound range. When the tone suits you, shorten the craft.

Tip: when the bark dries, the whistle stops whistling. Soak it for half an hour in water and it will work again.

Did your child like your gift so much that he whistles all day long? Build a pipe according to the same principle, doubling the length of the product and cutting several round holes on the bark, and listening to the music will be much more pleasant.

How to make a paper whistle

Even a kindergartner will make a paper whistle. True, the little thing will come out short-lived, but it will whistle strongly.

• Take a sheet of office paper and cut off one third of it horizontally.
• Set aside 1.5 cm to the right and left of the wide part, draw lines and wash them.
• Fold the figure in half so that the strips bent on the sides go to the outside. Cut out two triangles in the center of the fold.
• Place your lips on one triangle and blow into it, then blow into the second hole. Of course, the outgoing sounds bear little resemblance to a whistle, rather - it looks like the purring of a cartoon mammoth who was looking for his mother, but the kids will like it, that's for sure.

How to make a mini whistle

A whistle resembling a hunting decoy can be cut out of a tin coffee or beer can. Prepare: scissors, pliers, electrical tape, nails. See the drawing of the craft below.

• Cut out a piece of tin from a can, and from it - two rectangles, 20 x 40 mm in size. Mark them with a nail and make according to the template.

• Bend the wings on the first blank on both sides using a folding rule or fingers to make a 0.5 mm hole for air to pass through.

• Insert the second plate, assembled from tin, into the slot. Crimp the structure with pliers and tighten with electrical tape.

• Bend the tongue with a round pin.

• Close the sides of the tongue with your fingers and whistle. Do you think the whistle is too small? Adjust the model to the desired size by increasing its parameters proportionally.

In conclusion: all the whistles in our selection make piercingly loud sounds, so it's better to practice whistling in nature, and not in a city apartment.

Wooden whistle is a funny children's toy. The process of its manufacture can be of interest to both a child and an adult, especially since it is quite easy to make it yourself. At the same time, not everyone knows how to make a whistle. Although this activity does not take much time and effort. There is also no need for any special tool. All you need is a regular knife.

Branch selection

A whistle is best made from brittle ones. But you should not destroy a living tree. Many branches can be collected next to it. The best fit twigs with a thickness of not more than one centimeter. You can easily remove the bark from them with a knife.

Having collected enough branches, you should choose the only one from which you will make a whistle. To do this, find the most equal branch without knots and damage. Only 5-8 centimeters of a clean and even area on a branch will be enough. Pay attention to the bark: it must be perfect. The presence of kidneys will not be a hindrance - they can simply be removed.

After choosing a branch, you can cut off the excess part on one side, before the start of a smooth section. Having measured 5-7 centimeters from it, we make a circular incision. You will get a cut that resembles a ring. It should not be too deep, just cut through the bark, hitting the wood.

We remove the bark

It is necessary to separate the bark. We roll the stick on the table, pressing on it. You can tap with a knife handle. This will loosen its structure, and it will be much easier to separate it from the branch.

After tapping, you need to remove the bark with a rotational movement. It's important that she doesn't get hurt. The bark should peel off easily. If necessary, it is worth repeating tapping on the branch. Once removed, you'll get a bark cylinder. After setting aside 1-2 cm, make an incision in the shape of a semicircle.

Making a whistle

It is important to prepare all the details. A small cylinder should be cut off from the "bare" branch, no more than 1-2 cm long. The side side should be cut off from this cylinder. The cut should be wedge-shaped - this will allow you to adjust the sound.

We start assembly. Place the trimmed round timber with a wedge-shaped cut in its original place - in a cylinder of bark. You need to place it before the incision is made with the narrowed side.

Whistle ready

Having figured out how to make a whistle, you should start testing it. But the whistle should not only be tried, but the sound should also be adjusted. We press the free end of the tube from the bark with our fingers, after which you need to blow it as hard as possible. Finally, we hear a whistle. Of course, it may not work the first time. Everything can be corrected. Cut off a piece of the remaining branch and insert it into the free end of the bark tube. By moving it back and forth, you can adjust the strength and frequency of the whistle.

Now you know how to make your own wooden whistle. By analogy, you can make a more complex version of the whistle - the flute. This will require a stick of the same thickness, but of greater length - 10-12 cm. We also remove the bark and get a cylinder from it. Here, instead of one rounded incision, 3-4 incisions must be made. Plugging the open end of the tube with a stick, you can adjust the timbre of the sound with translational movements. By covering the holes with your fingers, you can play simple but pleasant melodies.

By learning how to make a whistle, you can make it quickly and in the shortest possible time. After all, this requires only the desired branch and a simple knife. This skill is especially useful for adults who want to please their children with such a toy. Having spent quite a bit of time and effort, you can please the child, giving him a lot of positive emotions.