How to install a shower tray - options from different materials. Installation of a shower tray

Installation of any shower stall or corner begins with the installation of a shower tray. A shower cabin is a wonderful addition to a regular bath, and is quite capable of completely replacing it.

The shower cabin can be placed both in a small room and in a huge luxurious room, stuffed with plumbing fixtures.

Whatever the shape and material of the pallet, the principles of its installation are similar.

• Preparing for installation
• Required consumables and tools
• Installing an acrylic shower tray
• Installation of a ceramic shower tray
• Shower tray finishing

Modern shower stalls are equipped with:

• hydromassage;
• light and music effects;
• tropical shower;
• working telephone;
• aromatherapy, etc.

The more different functions there are, the more expensive the shower cabin, the more difficult it is to install. It all starts with installing a shower tray.

Preparing for installation

Before you begin the work itself, as well as preparing consumables and tools, you need to select the pallet itself.

Preparing the installation site

The shower tray can have the following shape:

• square;
• rectangular;
• triangular with a beveled or rounded outer corner;
• U-shaped, etc.

Shower trays are made from a variety of materials:

• cast iron;
• become;
• ceramics;
• acrylic;
• marble.

Installing a shower tray is by far the most difficult part of installing a shower stall.

Steel pallet on a metal frame

There are several ways to install shower trays:

• on a metal frame;
• on plastic supports;
• just on a flat surface (ceramic trays).

You don't have to do the installation of the shower tray yourself. You can purchase a turnkey booth, and experienced specialists will install it quickly and with a guarantee. This will increase costs, but will allow you to use the shower cabin on the day of purchase. But this is far from the only reason why it is better not to install some shower trays yourself.

Acrylic pallet on a prefabricated frame

Some types of shower trays are best left to specialists:

• Marble pallets are very heavy, they can break even at the measuring stage.
• Ceramic trays are resistant to even very weak impacts.

Consider installing an acrylic and ceramic tray yourself.

Return to content

Required consumables and tools

1. Screwdriver and hammer drill;
2. Screwdriver Set;
3. Marker or pencil;
4. Drill with drills;
5. Electrical cable;
6. Sewer pipes;
7. Fastening mixture;
8. Plastic dowels;
9. Self-tapping screws;
10. Plugs;
11. Concrete solution, container for it;
12. Penoplex;
13. Master OK;
14. Silicone sealant.
15. Building level;

Return to content

Installing an acrylic shower tray

Acrylic pallets are lightweight, they have the greatest number of shapes and modifications. These models made of sanitary porcelain and sanitary ware are equipped with adjustable legs, mounting brackets and other fittings that allow installation as quickly as possible.

Important: The weak point of acrylic structures is the lack of support under its central part.

Strengthening the bottom of the pallet

When installing an acrylic shower tray correctly, special attention is paid to strengthening the bottom of the tray.

Acrylic tray installation diagram

Step 1. Preparation

Even before installing a shower stall, water supply pipes, sewerage and electrical wiring must be installed in the bathroom:

1. Hidden electrical wiring must have a minimum number of “twists” and also have high moisture resistance.
2. Sewage pipes, as well as water supply pipes, must have outlets to which hoses can be easily connected.

Step 2. Installation

1. The pallet is set strictly according to level.
2. We fix the central part without losing horizontal accuracy.
3. Installation of acrylic pallets is carried out on monolithic supports or podiums.
4. To perfectly install an acrylic tray, use a thin pencil to draw a thin line along the wall tiles along the entire perimeter of the tray.

Checking the horizontal level

Step 3. Consolidation

1. The strength of an acrylic tray is directly related to the size of the installation clearance.
2. It is advisable to leave access to the sewerage system.
3. Additional elements of the foundation are bricks or steel pipes.
4. Thick rubber is placed on top of the bricks or pipes.
5. Then the entire structure between the “acrylic tray” and the floor is pushed in tightly.
6. Fastening is carried out by applying mounting adhesive, then fixing the drain hole.
7. We connect the booth to communications.

Important: The easiest way to secure the pallet is to install support bricks under its base.

Return to content

Installation of a ceramic shower tray

Installing ceramic shower trays is not very common. Decorative ceramic shower trays are quite expensive, they are durable and beautiful, but they are cold and not resistant to mechanical stress, and can crack when hit by heavy objects.

When installing a ceramic tray, do not forget about its fragility

Ceramic shower trays are distinguished by the fact that they have no free space under the structure, they do not require any supports, so they are installed directly on the shower floor. In this case, no reinforcement work is needed, but there are difficulties in providing access to the drain pipe.

Drain hole for pan

Installation and fastening of ceramic structures is carried out with tile adhesive or cement-sand mortar, followed by installation of a drain hole.

Installation of a drain hole for a ceramic shower tray

1. The pan should be positioned so that the drain hole is as close as possible to the connected drain pipe.
2. Use a pencil or marker to mark the boundaries of the perimeter, as well as the location of the drain.
3. Use a jigsaw to cut out the part of the floor where the siphon will be located.
4. To ensure free access to communications, next to the first recess we cut out a second section of the floor outside the structure for laying a pipe under the floor and the siphon itself.
5. We make an inspection panel from a cut-out piece of flooring, equipping the edges of the cutout with slats.
6. Apply PVA diluted with water to the place where the shower tray will stand.
7. After the glue has dried, you can apply another thin layer.
8. The siphon is mounted to the drain, then the pan is installed on the prepared solution in a horizontal position.
9. After the solution has dried (24 hours), the siphon is connected to the pipe through an inspection panel.
10. The junction of the walls and the pallet is covered with a tape of silicone sealant.
11. If the shower tray is installed in a wooden building, then the walls are insulated with plastic film and roofing felt.

Treatment of joints with sealant

Return to content

Shower tray finishing

Whatever shower tray (acrylic or ceramic) you choose, the final stage of its installation is finishing work.

Finishing is carried out depending on the type of installation of the shower tray:

• When constructing a frame for support, the supporting structure is most often faced with tiles. Then all seams are sealed.
• When installing a pallet directly on the floor, an “apron” device is usually used with mandatory waterproofing of the seams.

Important : When installing the shower tray, do not forget to make a slight slope towards the drain. This avoids water collecting after using the shower.

Which shower tray to choose in your bathroom depends only on you. It is always worth thinking about this in advance in order to provide for all possible nuances. Whether you make a shower tray yourself or install a purchased shower stall, first of all you need to resolve issues regarding placement and appearance, water supply and sewerage schemes.

Heating: ◄

Building your own wooden house is a very responsible task, and the timing of occupancy, financial costs, and future comfort depend on how meticulously you approach it. While doing...
Comprehensive optimization of technical devices from the point of view of modern knowledge in various fields of science also affected climate control equipment. The desire to move away from a multi-unit air conditioning scheme (split system) has been relevant since the advent of such equipment. Why monoblock construction is relevant For some time now, when walking through any urban settlement, you are struck by the disgusting appearance of the facades of residential buildings. A huge accumulation of haphazardly installed The post Wall-mounted air conditioners without an external unit appeared first on StroyDvor....
The same problem occurs in network systems with flows of matter or energy. These include electrical networks, hydraulic networks, transport networks, computer networks and many others. There is even a separate branch of mathematics devoted to considering these issues. We will not deal with it, but will move on to specific applications of this theory to household heating systems and collectors with... Read more Hydroshoot with a collector: advantages of use and design features →...
Cost of installation of a water supply system from a well Invoice for payment No. 689 dated June 26, 2016 Supplier (Executor......
An air conditioning and ventilation system, in general, consists of various parts. Some can be dispensed with or can be replaced, while others......
Cost of materials for water supply repairs Invoice No. 780 dated July 02, 2016 Supplier (Contractor): DESIGN PRESTIGE LLC, INN 77332......
Heating plant cost of equipment Invoice for payment No. 1096 dated July 13, 2016 &nbs......
Pumping water from a pond to a vegetable garden, providing water supply to a small country house, cleaning a shallow pond or reservoir......
The main task of any kitchen hood is to clean the room air from various odors, remove soot and grease from it that settle......
The presence of water is an indispensable condition for comfortable living in a country house. It's not just that it's needed for cooking......
Smoking hookah rooms are a promising modern business area. But given the fact that hookah smoking rooms......
Contents: Design and principle of operation of a septic tank Classification of septic tanks How to determine the optimal size of a septic tank? Accommodation is clear......
Repair of the heating system Heating repair, except in emergency cases, is considered as a planned, seasonal event that follows......
It is difficult to imagine a well without concrete rings; they form its main and integral part. The wells themselves are divided into several types......
The Skat electric boiler is recommended for private use as the most economical, compact and safe option for a heat source for residential premises. This is an alternative to gas heating, an easy to install boiler that does not require......
Recuperative ventilation systems provide a flow of fresh air into the room, thus creating a favorable microclimate. The recovery process involves regular exchange of air masses. Recently, systems of this type have been widely used......
//www.youtube.com/watch?v=c9hvjWo8QPE //www.youtube.com/watch?v=D3j1Ih94swo //www.youtube.com/watch?v=ZZZWP1JFROg The post How to clean the air conditioner appeared first on StroyDvor.. ..
Construction and installation company Design Prestige complies with OKPD, which is very important for every owner of a country house, dacha, cottage, or other......
Electric wood heating at home is perfect for those places where there is no gas mains, and the delivery of other fuel is considered difficult......
Private home heating Private home heating is the opposite of central heating. Today the first can easily surpass in quality and efficiency......
High-quality heating - Copper pipes "The miser pays twice." This folk wisdom applies entirely to those who......
Re-equipment of the boiler room The constant increase in tariffs for the use of gas and electricity is a stimulating factor for heat conservation......
Modern home heating is innovative heating systems that are increasingly used......
All the advantages and disadvantages of conventional locks can be forgotten if you have an electromagnetic one. With 5 W of energy, it creates a force of 350 kg (Falcon EyE). You just need to put it right. So let's [...]
Repair of refrigerators Orekhovo-Borisovo Yuzhnoye Inexpensive. Price The Silver Frost company provides services for high-quality maintenance and inexpensive repair of refrigeration equipment in the Orekhovo-Borisovo Yuzhnoye region. We provide services at affordable prices in Moscow. By contacting us, you choose durability and reliability. Services include the following: refilling the refrigeration system with freon; diagnostics to identify faults; setting up the electronic system; testing equipment in operating mode; replacement of worn parts and assemblies with new ones; restoration of optimal performance of faulty elements; identifying and eliminating problems in the electrical circuit. All repair work is carried out by qualified and experienced craftsmen who have the appropriate professional skills. In addition, a high level of service quality is ensured.......
We believe that you need to start with the most general phrases about how to work with a milling cutter. Because a person may need some thing, but not understand exactly how it can be made. […]...
A wrench differs from a screwdriver in the shape of the head, firstly. In this case, we do not have a hex socket, but a standard 13 mm square rod (or other size). As a result, it becomes possible without […]...
An energy-saving lamp is a lighting device that is more efficient than a conventional filament light bulb. Today, several types of devices fall under this definition, which readers will learn about below. We will […]...
All houses and apartments are equipped with special ventilation holes, the main purpose of which is to maintain normal air composition. Purpose of ventilation in the bathroom: maintaining normal air humidity in a room with constantly used......
Installation of ITP, central heating point A heat point (TP) is a complex of devices and communications that provides connection to heating and hot water systems......

A shower stall without a tray is not always convenient in an apartment, so it’s worth choosing a bathtub, because it’s easy to install it yourself. Which trays are best for showers?

To figure out how to make a shower stall with your own hands, you need to explore all possible options. This also applies to the design, the choice of water drainage system, and the selection of materials for the construction and decoration of walls, as well as interior design. Since the number of combinations of all these elements is very large, the output we can get is something unique, and isn’t this a reason for a true engineer and designer to be proud?

So, the shower stall is built approximately according to this scenario:

• Choosing a shower design;
• Pallet installation;
• Floor installation with a slope;
• Installation of cabin partitions;
• Selection of internal equipment.

Self-made cabins can be equipped with a shower tray purchased at the appropriate store, or equipped with a sloping floor along which water flows towards the drain hole. If in the first case everything is clear, then installing an inclined floor will require some additional knowledge from you. If you do not have sufficient skills in working with concrete, then it is better to stop at buying a ready-made pallet, since such pallets are produced in a huge assortment and are not that expensive.

The shower room includes a fence, also made by hand. It’s good if there is a suitable niche for its installation, in which case all that remains is to install special doors or make do with curtains.

When the area of ​​the bathroom allows you to install a cubicle without compromising comfort, then the partitions can be made in a common style with the rest of the room, which will have a beneficial effect on the overall atmosphere and comfort.

In addition, it is necessary to measure the bathroom space, determine the places where pipes for supplying and draining water will be laid, and provide for the possibility of installing light. You also need to decide in advance on the type of mixer, or maybe a shower column with additional options, such as hydromassage.

Pallet installation

If you decide not to tempt fate and buy a ready-made pallet, then to install it you need to prepare a flat area; it is advisable to place a concrete screed on the bathroom floor, after laying down a waterproofing material. This is necessary in case of an accident and subsequent repair of the drainage system. Before installing the pan on the racks included in the kit, you need to install pipes for water drainage and install a siphon. Pay attention to the installation height of the tray in advance, this will help you choose the appropriate siphon. Installation of the shower tray should be done using a long building level. To make it easier to seal the joint between the wall and the pallet, it is recommended to make a small recess in the wall and push the edge of the pallet into it. It is better to cladding with ceramic tiles or other material after installing the pallet.

Inclined floor device

If you decide not to buy a ready-made shower tray, then you can build a cabin with an inclined floor yourself. With size and shape, in this case, nothing will limit you.

The main difficulty associated with installing a shower stall with a sloping floor is the need to raise the floor level to such an extent that water can drain on its own into the sewer system.

To do this, you can lay out a shower curtain around the perimeter. For these purposes, you can use brick or foam concrete. The latter is more convenient to process and give it rounded shapes. The side must match the shape of the shower stall. Next, you need to connect the sewer pipe and install a drain. You should not use siphons designed for installation in a tray, as there will be problems with cleaning it. The ladder is installed lower than the height of the sides to ensure the required slope, which should be 3-4 centimeters. Channels for pipes can be installed in the wall. Such channels are cut with a hammer drill, and after installation they are sealed with concrete mortar. Also on sale are ready-made sets of drainage channels with ladders.

After work with the sloping floor is completed, you can begin laying the tiles. Since such a floor is not a flat surface, it is most convenient to do this with small ceramic tiles, which are sold in the form of ready-made mosaics on a special substrate. For installation, use special waterproof glue.

Installation of cabin partitions

To construct enclosing elements, you can use various materials and their combinations. It is better to build the frame from a metal profile, but if you choose wood, you need to dry it well and treat it with a special protective compound to avoid rotting processes; larch has the best water-resistant properties. To build walls, many people prefer to use a material such as plasterboard, but we recommend choosing gypsum fiber boards; they do not contain cardboard, and as a result are more moisture resistant.

From gypsum fiber boards you can build a seat and shelves, which are subsequently lined with the same material as the partitions. Cladding work must be done with the same waterproof glue.

Partitions made from glass blocks look good. They come in a variety of colors, and some contain various decorative elements, such as plant arrangements, shells or starfish.

As a cheap alternative, you can use polycarbonate or plastic panels. These materials do not need to be decorated; simply screw them to the frame with self-tapping screws.

It is very important to ensure a good seal between the pallet and the partitions; a special sealant is used for this. When working with such sealant, use an excess amount; the excess can be removed with a soft spatula or cut off with a knife after complete drying.

To arrange the entrance to the shower stall, you can use simple curtains that are hung on a rod using rings. The lower ends of such curtains are usually located inside the tray so that water falling on them does not flow out. If you want to see a more rigid structure in this place, then ready-made sets of special hermetic doors are available for sale. Such doors can be hinged or sliding. The latter are convenient because in the open position they do not take up much space. If you decide to install hydromassage in your shower, then ordinary curtains will not suit you.

If the ceiling of the bathroom is too high to install partitions under it, it is necessary to install a ceiling on the shower stall itself. Plastic panels on a frame are best suited for this. It is convenient to install additional lighting and hood in such a ceiling.

Tag Cloud:

DIY shower cabin without tray

The acrylic shower tray is collapsing around the steam generator nozzle. Two years ago the acrylic was already repaired, but now cracks have appeared over a larger area.

Last time they explained to you that the Chinese steam generator produces steam that is too hot for acrylic, although the tray itself is very good.

We'll fix it again, but now we have to think about what to do with the steam.

The Chinese acrylic pan is cracked and leaking.

The hot water deformed the plastic and peeled off from the fiberglass.

The reinforcing layer is full of holes, so the sawdust under the bottom has rotted. Now the bottom bends a lot, so it cracks even more. We need to make a new bottom.

Cracks and chips on the bottom of the acrylic bathtub. I put a glossy magazine so that you could see the color of the acrylic in the photo. What and how can you do?

The crack runs along the frame channel. This means the bottom is weak. Chips are nonsense. We'll have to strengthen the bottom. The color of the bath is clear and available. We'll handle it during the day. It will be durable and quite beautiful.

Shower cabin Aqua Joy AJ-A-120A L (size 120x80x215). Country of manufacture, when we bought it, they wrote that it was
Kaliningrad, although most likely China. Two thin parallel cracks, each about 35 cm long, appeared at the bottom of the pan.

Water does not leak from them onto the floor. It seems to me that if you step between the cracks, then in this place the bottom bends down. But it’s difficult for me to understand whether this place falls on the convex or concave part of the bottom relief (the photographs show the bottom topography from below).

After the cracks formed, the cabin began to squeak a lot when you were in it, but after some time during the washing process, the creaking almost stopped.

Stiffening ribs made of chipboard are glued under the bottom of the pallet.

In theory, there should be a solid slab of chipboard, not pieces. Saving on sawdust. The plastic is very thin and bends and breaks along the stiffening rib.

The acrylic has already cracked, and the polyester putty with fiberglass underneath has not yet had time to break. That's why it's not leaking yet. During the washing process, the reinforcing layer gets wet and creaks less. The bottom needs to be strengthened well. There is no point in doing anything under the bottom unless you build additional support. We will work from the front side. It seems that it can be done very firmly and almost imperceptibly. It’s hard to say exactly how many hours you’ll have to work, but we’ll do it in one day.

My shower tray leaked on the Serena SE-12013G high tray, 90x90, round.

Apparently, there is a delamination of the acrylic, and maybe a break (it is pressed when pressed). There is a small crack inside and outside (but in slightly different places, not through). The pallet is undermining. How much will the repair cost, and is repair possible, or does the pallet need to be replaced?

Judging by the description, the Chinese acrylic tray broke under the weight of a person.

Since the cracks on and underneath the tray are in different places, this means that the plastic has become deformed and peeled off from the fiberglass polyester resin. The strength of the trough has decreased significantly.

How to install a shower cabin with your own hands

It should be strengthened on both sides if possible. The cost of the work will be slightly higher than the minimum order value.

The acrylic shower tray is cracked and leaking.

It bends a little. What can be done?

An ordinary Chinese grayish flimsy pallet, that's why it broke.

It is necessary to thoroughly strengthen the place where the hole is, and at the same time the entire bottom. You can also support it from below. Choosing a color is not a problem.

My pallet broke in the “first step zone”, a crack 1.5-2 cm long, along the entire length of the “pimples” (the pallet has a pimply surface, in squares).

From below in this place one of the beams of the fastening cross passes, at the end of which legs are installed. And if you look at the pan from below, there is delamination of the acrylic (I think) to the right of the crack, you can see brown stains through which water is dripping in (it collects and drips in).

But they are not end-to-end. I'm sending photos. The plumber coated the inside of the pan with something like liquid rubber, I don’t know for sure, but it comes out easily if you pull it. The pallet itself
tall, quarter circle, 90x90cm. Is it possible to repair the pallet? In what time frame can this be done?

The profile of the frame cross almost does not touch the bathtub.

There is no chipboard under the pallet for strength. There is only fiberglass, which broke safely. The acrylic has peeled off from the polyester resin.

The pan is leaking because the acrylic and fiberglass are torn. You will have to work under the pallet and in the pallet.

We'll get it done in a day. It will turn out beautifully.

Tell me how much it will cost to repair the bathtub - see the through damage in the photo - temporarily sealed with tape. Dimensions approximately: 30*5 mm. The sliding door fell.

In the photo, you can't see if there are any cracks around the hole.

The complexity of the repair depends on this. In any case, it can be fixed. It will turn out more beautiful if you can reach the hole with your hand from the outside.

A shower cabin is installed in the beauty salon. I would like to update the coating to make it look good.

The photo shows damage from chemicals under the water intake hole and on the nozzles; most likely there are cracks there.

Near the steam generator, the acrylic is damaged by hot steam and, possibly, aromatic oil. There are cracks in the bottom of the shower tray. The sawdust under the plastic has swollen and in those places where the frame profiles are located, the acrylic is torn. It seems that there is little point in repairing this Chinese pallet; it won’t work out beautifully.

Hello!

We retail shower cabins that we ourselves imported from China. During transportation, some pallets were damaged - approximately 20 pallets (scratches, cracks and chips). Would you like to offer you to repair/restore our pallets (for further sale)?

It is impossible to RELIABLY seal CRACKS on Chinese pallets so that they are completely invisible.

Recording a low pressure shower. One of the eternal questions that every person encounters in his life is the choice of a bathtub or shower.

Currently, a low-level shower can be considered one of the most hygienic and practical options. The cabin installation instructions will help you deal with any possible problems.

When installing this format in the bathroom, you can reduce the water consumption in water procedures, in addition, you do not spend a lot of time lounging in the bathroom and relaxing.

One of the most important issues is the height of the side of the pallet. Depending on what the owners of the house are.

Low range showers are those that have a side height of 0.5-1 cm. For all people, this height is comfortable. If, however, elderly people or small children live in the house or home, it is important that the cabin is as comfortable as possible for all family members.

Shower enclosures with a low palette are a modern and aesthetic option.

You can easily step on the bottom to use the shower.

Advantages of a low tray

Using a low pressure shower has many positive aspects:

• all models are sorted by model, so they fit perfectly into any interior and become more alive;
• The low temperature shower is ideal for a small room and does not take much time to install;
• models of this type are very diverse, completely complement the interior and fit perfectly;
• Due to the low palette and the presence of a tight door, water does not fall on the floor; in addition, the interior is very simple;
• Taking water in the bathroom is very convenient to accompany a child or help the elderly.

However, the cabin installation has a low defect spectrum.

weak sides

Disadvantages of low level pallets include the following:

• such models do not always have good sealing, so you need to install curtains or doors;
• The low sides make it impossible to collect water to buy a child. You also won't be able to use the tank to store different types of products;
• The tray heats up very slowly, which may cause discomfort to many people.

Variety of low range showers

Shower enclosures vary depending on the materials from which they are made and depending on the type, shape and availability of certain functions.

How to install a shower with a palette yourself

Pallets are often made of cast iron, steel, spores or acrylic:

• Cast iron is a material that is not only heavy, but also very expensive. Significantly maintains heat compared to steel and acrylic;
• a steel tray is “louder”, it can also bend under the weight of a person;
• many people prefer acrylic because it softens the sound of water, it is more durable and comes in different colors;
• Quarrel is a very interesting material that combines the advantages of acrylic and the beauty of a stone product.

  If desired, the shower cabin can be made of natural stone to order.

If the size of your bathtub allows you to purchase a larger stall, you can choose a model with a sit-on seat.

In some low concentration showers you can use fragrances and music. These models have a touch screen that allows you to switch modes.

Shower cabins with sliding doors are very popular.

But if you have enough space in your bathroom, you can install a model with a swing door.

Low-end corner shower models are an excellent option for very small bathrooms.

In addition, if you want to install such a device, you do not need to have special skills - it is very important to simply approach this issue responsibly and familiarize yourself with the stand installation diagram.

Installation of shower cable

When shopping for a shower, consider your bathroom options.

Don't forget that choosing cast iron pallets is a good choice as they are durable and easy to use.

If you purchased a simple, low-light model, you can watch video installation instructions online. Here you can find out what tools you will need to install the structure.

Installation of a shower product can be roughly divided into the following stages:

• siphon installation, which means the placement is below the bottom of the shower.

  The lower part refers to the installation location, describing the example and drains. When it moves to the intended area, a low siphon is installed.

  The cabin is then fixed and the pallet is loaded and compressed;

• Wall installation begins with the assembly of the locks or frame, as well as the vertical stand. After this, the fabrics are inserted into the recesses and secured with rubber parts. For strength, the walls are screwed in. Use self-tapping screws and fasteners to perfectly fit the profile.

  If you want to cover the closed storm cable screen more tightly, you need to connect the canvas to the frame brackets, then pull it and grease the profile parts;

• door installation. The fabric door is attached to the top and bottom through specially prepared holes.

  The doors are first connected to the rollers at the top and then the buttons are used for alignment. On a suspended canvas in the upper part it is mounted on lower rollers by a spring. This completes the installation process.

If you are confident in your abilities, you cannot invite professionals to install the shower and do everything yourself using special designs.

Installing a short-range booth is not a complicated process, but it does require some skill. If you are careful and pay attention to details, you will get a shower that will keep you strong and safe.

The differences in a deep bowl setup aren't that big of a deal, so you shouldn't have too much trouble.

Shower stalls are deservedly popular. Every owner dreams that a newly purchased new cabin will delight him for many years, without causing any trouble in the form of neighbors flooded from below. This condition can be met only under one condition - the shower tray must be installed in accordance with all the rules of professional installation. It is worth considering in detail how to install a shower tray so that it serves for many years.

Types of pallet designs

Improper installation of the pallet over time leads to its gradual destruction and, as a result, complete failure.

Note! When installing a pallet that rises above the floor, it is advisable to install an additional step. This is necessary not only to make getting into the shower stall as comfortable as possible, but also for safety reasons.

If all installation is done correctly and according to the instructions, the shower stall will please all family members for a long time and will leave the neighbors dry.