How to glue wallpaper in the corners of a wall room. How beautiful it is to join different types of wallpaper in the corners, especially if they are uneven

The easiest way to update the interior of an apartment is to wallpaper the walls. However, while doing the work, many face some difficulties. The greatest difficulty is gluing wallpaper in the corners. In these places, when carrying out repairs, many make mistakes that spoil general view of the updated finish. It is enough to familiarize yourself with the algorithm, which suggests the correctness of such actions, and such problems will no longer arise during subsequent repair work.

Wallpapering in corner areas

The main difficulties that apartment owners face when pasting walls with finishing materials are uneven external and internal corners, often having uneven geometry. All this not only complicates the process of gluing decorative material, but also significantly increases the repair time, which is hardly included in the plans of any person.

Ultimately, the owners of the premises are forced to additionally process the surface of the walls. At the same time, even the subsequent use of high-quality materials is not a guarantee that the corners will be perfectly even. This gives the impression that the work is done unprofessionally and spoils the overall look of the room.

Few people know how to properly glue wallpaper in the corners of a room. In order to properly perform this process, it is necessary to follow a certain sequence of actions. Before doing this, remember the following:

As the work approaches the next wall joint, the strip of wallpaper is trimmed so that it is only a few inches pasted onto the adjacent wall. Then the wall treated with adhesive. After the strip is fixed on the wall, it must be ironed with a rubber spatula or pressed with a roller. It is important that there are no folds at the junction of two walls, even if an uneven bevel of the edge of the strip is obtained on the adjacent wall. If the material is very dense, then shallow cuts can be made from the inside of the finishing paper material. In this case, the canvas will be better adjacent to the interface of the walls.

Then, on the wall, where there is a smaller part of the wallpaper strip, a straight line is drawn from floor to ceiling using a level or plumb line. In this case, you should retreat from the corner by the width of the roll. Next, the glue is applied to the wall, and a strip cut is applied to the existing line. At the same time, its edge will overlap the uneven edge of the previous piece of wallpaper.

When both bands are fixed, it is necessary to determine the place of the smallest overlap. It should be divided in half and draw a straight line from the middle along the entire height of the corner, then cut it with a sharp knife or blade.

The upper piece of material must be carefully removed, folded over and the cut off part of the lower strip removed. Then both edges of the wallpaper are smeared again glue, close and gently smooth out with a roller. The result should be a perfectly even angle, and there will be no sags or gaps at the junction.

Carrying out wallpapering in the corners, it is necessary to wait some time after fixing them on the wall. Otherwise, the material wet from the adhesive composition cannot be cut evenly. As you can see, there is nothing complicated in this process if you follow the algorithm

.

Such corners are much less common indoors. Wallpapering them works in a similar way:

It must be remembered: even in the case of perfectly even corners, one should not strive to wrap the whole canvas. This is most often leads to wrinkles and irregularities, as well as a high probability that the material will swell and bristle ugly. As a result, it will be necessary to carry out repair work again, which requires financial costs. The whole canvas is wrapped only when wallpapering on window or door slopes.

Cutting off part of the canvas will not lead to a large consumption of wallpaper, so gluing wallpaper on the corners will not require an increase in spending. In general, the work is not difficult, but there are small nuances. If you take them into account, everything will be done correctly in accordance with your own requirements. If there is no self-confidence, it is better to entrust the work to professionals.

Wallpaper is one of the most common types of decorative wall decoration. For wallpapering walls no perfect alignment required. This advantage distinguishes wallpaper from other materials.

Painted wallpapers are especially versatile. But when sticking them on the walls, some problems may be finishing of internal and external corners.

In order to glue the wallpaper on the corners evenly, it is necessary strictly adhere to the recommendations of the masters. You need to start docking and pasting wallpaper in the corners by taking measurements at the bottom and top of the walls.

Non-woven wallpapers are the most popular and affordable materials for wall decoration. They can hide small irregularities in the surface of the walls. If the walls have small flaws, it is possible that corners may also have some unevenness.

To correctly paste over the corners with non-woven wallpaper, necessary:

• measure distance from the last glued strip to the corner. Add about 15mm to this distance. stock;
• From a cooked strip of wallpaper cut to size when measuring the wall. After that, glue is applied to the wall and the resulting piece of wallpaper is applied;
• now wallpaper smoothed out along the wall to the corner. Then we wrap the edge of the wallpaper on another wall, and also smooth it out so as to avoid bumps or swelling of the material;
• If the strip is skewed, it does not need to be re-glued. You can safely measure the next strip and stick with an overlap. This operation will hide the resulting distortion;
• If the pattern does not match, move the wallpaper as far as possible up or down, left or right, as far as the distance allows, to roughly align the pattern;
• Paste the corner a whole strip is highly undesirable.

Today, pasting walls with vinyl wallpaper is a fairly common way to decorate an apartment. The peculiarity of this wallpaper is that they can be washed, do not wrinkle and do not lose color or texture over time. Non-woven wallpaper has the same properties.

Vinyl wallpapers have their own features and requirements for pasting. Despite this, the methods of pasting non-woven and vinyl wallpapers are approximately the same.

To get it right cover the corners with vinyl wallpaper, need:

• Do measuring distance to corner and choose the method and orientation of the wallpaper strips on the wall. You can start wallpapering from the corner, but this is done only by experienced professionals;
• According to the result start gluing stripes wallpaper so that there is an overlap of 3 cm around the corner. After that, we lubricate the wall with glue and lean strip after strip to the very corner;
• Smoothing out the pasted part of the walls in the direction of the corner;
• On the corner you need to be careful grease the wallpaper and bend a piece of wallpaper, smoothing them with a dense cloth to avoid wrinkles and irregularities;
• On the other hand overlap we join another part of the wallpaper;
• After that, we lean the ruler or level against the overlap and cut with a sharp knife;
• Trimmings should be removed;
• Lubricate the wallpaper liberally with glue and lean the joint against the wall. In this case, we get an evenly glued corner with vinyl wallpaper.

Pasting the outer corners is a very difficult task. But don't panic that you won't succeed. Just you need to know some tricks and methods pasting the outer corners of the premises of a house or apartment.

The process of sticking stripes of wallpaper on the outer corner is no different from the methods with inner corners. Such a process includes several actions:

• Need to start from the removal of the required dimensions. We measure the distance from the corner to the last glued strip. It is necessary to measure from above and below to determine the evenness or unevenness of the angle. We also take into account the size of the overlap around the corner of 2.5 cm;
• After that transfer the resulting size to the web of the roll. Having drawn the cut lines, we cut the wallpaper and get a strip of the desired size;
• We apply glue to the wall;
• We take strip and attach to the wall by smoothing it with a rubber spatula or soft cloth. We also do with the overlap area;

• Then the next piece is cut from the roll and glued with an overlap from the corner along the wall. This method of pasting will hide possible uneven corners and stripes of wallpaper.

Also watch a master class from a specialist on how to glue and cut wallpaper in the corners

To put it bluntly, everyone knows how to glue wallpaper. The matter is quite simple. It's almost like gluing children's stencils - by the way, there are also such types of wallpaper, on which the adhesive layer has already been applied.

But the material is much larger and the glue will need not a bottle, but a bucket. Therefore, we get down to business quite briskly, choosing the beginning of the surface to be treated.

Key points

Corners are far from the most prominent place in the interior of any room, but it is the quality of their finish that determines the real class of work.

Here we only define, for starters, what situations we may encounter.

Types of corners

The order of work will largely depend on what angle awaits us:

• internal between two vertical walls - there are such in any room, there are almost always at least four of them;
• external, also between two walls - there may not be such at all, they can be avoided by finishing the window slopes to the corner; but if there is an external corner, it is he who will require the most work;
• internal horizontal at the bottom, between the floor and the wall;
• internal horizontal at the top, between the wall and the ceiling - the last two types could not be taken into account if you prudently approach the organization of these corners.

About materials and tools

Before we get started, let's look at what we will be dealing with:

• Non-woven wallpaper - they are the main reason for all our actions, the most famous finishing material for walls. Wallpapers are made on the basis of long-standing paper ones - in them 70% is occupied by a cellulose layer, but with the addition of synthetic components that strengthen and give more flexibility, which provide the remarkable qualities of this material. To work on the corners here from paper - good flexibility, and from additives - great strength, which will not allow the material to tear at the most inopportune moment.
  When it comes to wallpaper, their dimensions are especially important:

• in width you need to count on 53 or 106 cm,
• and along the length (height) - by 10.05 meters.

• Glue - you can use universal wallpaper glue, but we still recommend a special one for non-woven, which, by the way, is not suitable for any others.
• Rollers - it is advisable to stock up on a whole set for all occasions:
  • for applying glue;
  • for smoothing wallpaper already on the work surface;
  • for work at the joints, and,
  • for corner work.

• Plumb line, ruler, level, pencil, scissors - you will have to measure and cut a lot, but most importantly - from the very beginning it will be necessary to get an ideal vertical line on the wall, and all further work will begin from it.

Helpful advice!
If in the future you will be able to strictly adhere to the received vertical, then it will be enough for one.
But we advise you to draw these lines on all four walls, closer to each corner, which will allow you to control the process more accurately.
Departure from the vertical always leads to very unpleasant errors and even the need for a complete re-glue of the roll.

• The cutting tool is necessarily comfortable with a well-honed edge;
• A trowel, a trowel, a convenient wide ruler - anything that allows you to get and control the cut line.

Nuances of preliminary preparation

The stage is preceded by very important steps for preparing a rough working surface.

As for the corners, it will be very important:

• when working at the top and bottom - provide for the installation of skirting boards as a last resort, after the wallpaper, then:

• the task of fitting the joint simply disappears by itself, the edges will be covered with skirting boards, providing a perfect joint;
• in this situation, if we take into account the standard height of the premises of 2.5 meters, the length of the wallpaper is 10, and the height of the plinth along the wall is 5 cm, then the roll is cut into 4 pieces of 2.5 each, which is enough for four verticals, and without any waste ; otherwise, given the allowances, you will have to cut more than 2.5, which means that 3 pieces will go into action and one shortened one will remain neither to the village nor to the city;

• it is very useful to use removable skirting boards - this will solve the problem with docking if you want to change the wallpaper in the future;
• when working on internal corners - they must be strengthened with non-woven paper tape, which is glued directly to the putty, and is also puttied on top;
• on the outer corners - it is better to carry out a more thorough reinforcement with the help of metal or plastic corners, which are fixed with screws; the corners are attached to the putty, and they are also puttied on top.

Helpful advice!
If your corners are not straight, we recommend using plastic corners, they are more convenient to select the desired angle.
There are quite a few options for reinforcing corners, but given that we will slightly trim the wallpaper further at the corners, it is better to use solid corners, without perforation.

• if we talk about the surface as a whole, then it should be:

• dried thoroughly,
• aligned
• primed
• puttied and
• sanded - at least with sandpaper by hand, but better with a machine.

Work progress

Consider in order all the angles, from simple to complex.

Angles top and bottom

Everything is quite simple here, even if you can’t hide the material under the plinth:

• cut wallpaper with an allowance above (or below) the plinth by 6-8 cm;
• glue and bend the allowance along the plinth line what is convenient to do ;
• then, using a spatula as a guide, cut off the allowance along the entire length with a knife;

• work must be done while the glue has not yet set, this will allow a small residue of 1-2 mm to be carefully inserted with a knife over the line of the plinth.

Angle inside

Here, first we provide ourselves with two reliable verticals on both joined surfaces:

• first we glue the wallpaper on one side so that the area, at least 2 cm wide, goes to the adjacent wall;
• waiting for the glue to dry completely;
• usually 2 cm of allowance will be enough to glue the adjacent piece if you've made more and it's holding up well then there's no need to cut it off, otherwise be sure to cut it off using a sharp knife and spatula as a guide;
• glue a piece on the adjacent wall right next to the corner and smooth it with a special;

• there is always a temptation to avoid such a hassle, bend the piece in half in width and try to create a "perfect" angle from one piece; but, as practice shows, the wallpaper in the future will begin to run together and the whole corner will simply move away; nevertheless, we advise you to keep this method in mind; if you have very high-quality wallpapers that “do not come together” over time, and even under glue, then this option will be just perfect.

Helpful advice!
When pasting wallpapers, in no case do not stretch them on glue - when the glue dries, the material will definitely “run down”, exposing wide joints.
In addition, be sure to determine what kind of wallpaper you have at your disposal.
There are options that generally overlap should not be glued, only end-to-end.
Some are glued only with a shift relative to the adjacent piece or even with a 180 degree turn.

Sticker wallpaper in the corners is the most difficult. Both the material itself and the properly prepared plane are important here. How to glue wallpaper in the corners, we will consider in this article. Expert advice will also be given. On the video and photo you can see everything yourself and better understand.

For an ideal result, without cutting the wallpaper at the fold, the corners in the room must be even. In such a situation, all the work will consist in processing the walls and wallpaper with an adhesive composition with further pasting.

However, it is very difficult to find a room with perfectly even, geometrically correct characteristics, even if one corner will spoil the overall picture.

What will affect the work:

Possible problems and subtleties when gluing wallpaper on corners

An important point, when performing this type of work, is the material from which the selected wallpaper was made. Different materials behave differently during the gluing process. And when doing the work with your own hands, you need to know these subtleties.

The instruction in this matter will be as follows:

Note: The overlap depends on how dense the material is. For example, if glass wall paper is used, the strips are glued joint to joint. Even a slight overlap will be noticeable.

How to glue wallpaper on an inner corner

The main goal when sticking wallpaper is to prevent “wrinkles” from appearing in the corners, and the wallpaper sheets themselves do not diverge.

So:

• To prevent this from happening, the canvas is wound up so that a grip of no more than 2 cm is formed on the adjacent wall. At the same time, it is necessary to take into account how uneven the angle is, and the stronger the curvature, the more allowance is left. The edge is pressed against the wall with maximum force. In the case when wrinkles begin to form on the strip, it is necessary to make neat cuts with scissors, cutting the canvas, heading towards the fold.
• The next step will be the marking, the next strip of wallpaper on the adjacent wall will be superimposed on it. From the allowance of the first strip that has entered the second wall, measure the distance of the width of the wallpaper sheet with a decrease of 5 mm.
• Then, using the level, a vertical line is drawn on this section of the wall. Upon completion of the markup, the next sheet is glued. In order for it to be perfectly level, a guideline is taken on the drawn line.

How to glue wallpaper on the outer corner

Wallpapering on outside corners has its problems, but it's possible to avoid them if done professionally.

Attention: In order for the wallpaper to fit perfectly on the outer corner, the point from which the sheet will go is determined so that its edge goes around the corner by 3 cm.

• The edge of the sheet is pressed against the wall with maximum force. In the case of wrinkles, as well as when working with internal corners, small cuts are made.
• Along the edge of the sheet, you can tear off a thin strip of wallpaper so that only a thin edge remains. This method allows you to seam more neatly, and will make the overlap less noticeable.
• After that, using a level, a value equal to the canvas and increased by 0.5 cm is marked from the corner. The next sheet is glued along the resulting line in such a way that its edge overlaps the torn edge of the previous canvas.
• The junction is pressed through with maximum effort, the upper and lower edges of the wallpaper are trimmed by trimming, after which the sheets are rolled with a rubber roller.

How to glue wallpaper with a pattern in the corner

When a pattern with vertically arranged stripes is applied to the wallpaper, the corners will be most visible if it is distorted. And with horizontal lines, pattern violations will be visible approaching the floor and ceiling plinths.

Avoiding these problems is easy:

• Do not forget to leave an overlap on the next wall;
• hide the resulting joint in the upper part of the corner;
• glue the wallpaper in the corner of the room so that the edge of the canvas lies perfectly even with the line drawn in advance. In this case, the second edge is cut to the edge of the corner.

It is rarely possible to completely avoid distortion of the pattern, minor errors are likely to remain. But only you will know about this shortcoming. Indeed, to detect it, you will have to carefully examine all the corners in the room. Subject to all the rules, the wallpaper will be perfectly even, and the pattern will not be disturbed.

Repairing an apartment or house is a very complex and time-consuming process. And if workers make it for you, it is also expensive, since the price for the services of craftsmen is often the same as the cost of the material. Therefore, if you do at least some of the repair work yourself, you can save a lot. Many people successfully wallpaper themselves, and find nothing difficult in this, except to glue the wallpaper in the corners.

Wallpapering in the corners is a responsible and important stage of work

Even in very good apartments there are bad corners. Not good because they are not perfectly aligned. What do the masters advise?

When pasting the outer corner, make sure that the strip fits snugly against the wall

Never glue a whole strip of wallpaper. If the corner is uneven, the strip will fold over and not meet with the other strip. Leave a ledge around the corner by 1.5-2 cm, then the strip will lie against the wall. Be sure to use a plumb line if you are gluing thick wallpaper. Glue a piece with a slight overlap to the adjacent wall so that it is as vertical as possible.

If there are switches or sockets close to the corner, you must first remove the casings, not forgetting to turn off the electricity in advance. Stick the canvas on the sockets and switches, then make cuts on the wallpaper and cut the circle slightly smaller than the size of the casing. Then put the covers back in place.

When pasting the wall at the door, it is better to approach the doors from both sides. The strip of wallpaper that covers the door must be cut vertically to the beginning of the frame. It is attached along the edge of the wall. The protrusion should be cut and fit over the door frame.

How to glue wallpaper in the corners: step by step instructions

• Step 1: preparing the corner

This step is performed long before the actual wallpapering at the stage of wall puttying. The corners of the room should be equipped with special plastic corners. They are attached to the walls with putty, and must be fixed very securely. After that, you can proceed to the design of the corners of the room.

Do not glue all the corners at once. Having chosen the corner where you will start, prepare a strip of wallpaper of the desired length. Coat the area with wallpaper glue along the width of the cut strip (plus 3-5 cm), do not forget to glue the plastic corner as well. When the wall section and corner are treated with glue, attach the wallpaper there. If you started gluing from left to right, you need to attach the left side to the inside of the corner so that the strip is perfectly even along its entire length.

• Step 3: leveling the wallpaper

Align the wallpaper well in the corners to visually hide existing defects

Wallpaper is rolled out with a special roller or spatula. After that, the next section of the wall is covered with glue, and the wallpaper is glued to the next corner. How to glue the closing corner? A new strip should be associated with the last wallpaper strip. Roll the glue towards the corner, and when the wallpaper is glued to the inside of the corner, cut off the excess area along the inside line of the corner with a clerical knife.

How to glue non-woven wallpaper in the corners

Interlining is a special material that consists of cellulose and non-woven fibers. These are wallpapers that are intended for painting, since their outer layer is not resistant to mechanical damage. Gluing non-woven wallpaper in the corners is much easier than any other wallpaper, since the glue is applied only to the wall, and a dry wallpaper is attached to it. Having previously decorated the corner of the room with a plastic corner, stick it in the same way as described above.

How to glue wallpaper with a pattern in the corners

With a clear geometric pattern on the wallpaper, distortion must be minimized

If the pattern on the wallpaper with vertical lines, it is in the corners of the room that its distortion will be especially noticeable. And if the drawing is horizontal, it will be skewed in relation to the ceiling and baseboards. How to avoid such troubles? Everything is simple. Firstly, do not forget to make a small overlap on the adjacent wall, and secondly, hide the existing joint at the top of the corner. Thirdly, try to stick wallpaper in the corners of the room so that the even edge lies exactly along the vertical line you draw (along the plumb line). In this case, the other edge is trimmed along the edge of the corner.

It is unlikely that a shift in the pattern will be completely avoided - a slight shift is likely to remain. But this is a flaw that only you will know about. After all, to find it, you need to carefully study the corners of the room. If you follow all the rules, the wallpaper will lie vertically on the adjacent wall, which means that the distortion of the pattern will not be noticeable.